Engineering Commons^™

Rapid Animatronic Target System, Brandon Keith Bray, Matt Gerhardt Guise, Martin Thomas Quinn

Mechanical Engineering

No abstract provided.

Characterization Of The Relationship Between The Microstructure And Tensile Strength Of Annealed Ti-6al-4v, Aldo Corona

Materials Engineering

Tensile coupons of Ti-6Al-4V were heat treated at varying annealing temperatures from 1200°F (648°C) to 1450°F (787°C)  at 50°F  (23°C) increments for 1 hour. The samples were air cooled to room temperature or furnace cooled to 800°F (426°C) followed by air cooling to room temperature. Four tensile coupons were treated at each annealing temperature and cooling rate. Alpha case was observed to form on the surface of the samples post heat treatment with a maximum depth of 25 µm (.001 in). Samples were tensile tested for their ultimate tensile strength, yield strength, and percent elongation.  Samples across all annealing temperatures …

The Effects Of Colorant Oxides And Firing Rate On The Nucleation And Growth Of Zinc Silicate Crystals In Crystalline Glazes, Nicolas Coffey

Materials Engineering

This study looked at the effects of colorant oxides and firing rate on the nucleation and growth of crystals in zinc-based crystalline glazes. One weight percent of iron and copper oxide powders were mixed separately with a zinc-based crystalline glaze. The uncolored glaze along with both colored glazes were applied to test tiles and fired. Two different firing schedules were used with different ramp up firing rates of 165°C/hr (slow) and 205°C/hr (fast). X-ray diffraction (XRD) analysis found both zinc oxide and silica oxide in the raw glaze, which are the main components in the formation of zinc silicate. XRD …

Processing Pdms Gecko Tape Using Isopore Filters And Silicon Wafer Templates, Boris Luu

Materials Engineering

Gecko tape was processed through nanomolding involving two types of templates. One template was a Millapore Isopore polycarbonate membrane filter and the other template was an n-type silicon wafer processed to include four different pore diameters. These pore diameters were 20, 40, 80, and 160 microns. AutoCAD was used to design to a mask to be used later during photolithography. Two n-type wafers were sputtered with aluminum, underwent photolithography, and then etched using reactive ion etching. A template was placed into a Petri dish and Sylgard 184 polydimethylsiloxane (PDMS) was poured on the template. Once the PDMS cured,   the 1 …

Oxidation Kinetics Of Silver Thin Films For Antimicrobial Applications In The Health Care Industry, Sean D. Morham

Materials Engineering

To determine if varying city water qualities from around the United States can support a developing “oxidation corrosion of silver thin films” method of creating aqueous ionic silver solutions for the anti-microbial treatment of healthcare linens, a test was devised holding all variables constant with the exception of water quality parameters. This corrosion style test was done in order to assess a pass/fail criteria of 25 ppb ionic silver concentration in the aqueous solutions which resulted from the corrosion of silver thin film coated substrates. Above 25 ppb being a pass, below 25 ppb being a fail. While varying the …

Investigating The Mechanical Properties Of Compression Molded Carbon Fiber Reinforced Sheet Molding Compound, Bradley A. Jones

Materials Engineering

Callaway Golf receives a proprietary blend of prepreg material from Quantum Composites. Callaway processes the prepreg in-house and supplied 254mm x 254mm x 1.3mm panels of carbon fiber sheet molding compound (CFSMC) for characterizing. Tensile strength was analyzed by conducting tensile tests per ASTM D3039. Tensile coupons were cut to 254mm long by 25.4mm wide. Tabs were constructed from 1.6mm thick GFRP printed circuit board material. A commercial grade two part epoxy was used to bond the tabs to the CFSMC. Tensile results were inconclusive due to consistent fractures occurring outside the gauge lengths of the specimens.

Flexure strength was …

Improving Cal Poly Space Systems Infrastructure, Tyler Richier

Industrial and Manufacturing Engineering

The goal of this project was to increase the usable space for the club Cal Poly Space Systems to work on its projects, improve the safety for its members, and reduce the time it takes to manufacture its products. The project demonstrated the effectiveness of 5S in improving a workspace. Club members were measurably more comfortable in the work environment and spent less time looking for tools. Current rooms were made more professional by ridding the workplace of non-valued items and finding sensible locations for high-traffic items. Additional rooms were added and they should indisputably support club projects the upcoming …

5s Implementation Plan For The Shipping Department At Helical Products Co., Eric William Walker

Industrial and Manufacturing Engineering

Helical Products Company is a business that manufactures flexure products, such as couplings and u-joints. As part of a movement towards lean manufacturing, Helical Products Company of Santa Maria, California is in need of a principle that will help them continuously improve their shipping department. A study of 5S, a lean principle focused on waste reduction, will be done to investigate opportunity for implementation. A literature review takes a peek on research of lean manufacturing history, lean workbook/ tutorials and lastly case studies and journal articles. The output of research provides a design plan for Helical using 5S and other …

Ackermann Steering Geometry Applied To A Skateboard Truck, Daniel D. Downs

Industrial and Manufacturing Engineering

Conventional skateboard trucks are currently unable to meet the challenges of the modern enthusiast. They are lacking in key performance metrics such as handling, stability, and traction. Longboard enthusiasts, whom rely heavily on handling performance, are hungry for new and innovative technology to help bring the sport to the next level. The aim of this project was to solve these problems by applying specific aspects of automotive steering geometry and best engineering practices. Three successive prototypes were designed, with the first two prototype sets being manufactured and extensively tested. The first prototype served as a proof of concept, but suffered …

Cardiac Staging Facility Workflow Redesign, Ryan Chang

Industrial and Manufacturing Engineering

This study analyzes and proposes Cardiac Staging nurse workflow improvements along with a new Cardiac Staging facility design at French Hospital. Currently, patients spend an expected 125 minutes in Cardiac Staging. It was found that 60% of the time in Cardiac Staging was spent waiting to be transferred into the Cath Lab. The following Industrial Engineering methods were utilized to eliminate waste in staging and design a new staging area:

 Use of Lean and Six-Sigma tools to recommend new patient arrival time

 Manufacturing product scheduling to reduce patient wait time

 Use of facility redesign techniques to improve …

Chinese To English Introductory Cover Letter Generator, Jason L. Stine

Liberal Arts and Engineering Studies

The Chinese to English Introductory Cover Letter Generator allows Chinese computer users who know little to no English automatically generate a self-introductory cover letter in good English. As an example, professors in English-speaking countries are increasingly receiving emails from students abroad in countries like China, and these students often need to introduce themselves in order to support their reasons for their message. Unfortunately, more often than not these letters contain poorly written English. This software aims to help solve this issue. Using a combination of a “sentence template” system and intelligent natural language processing software, the program assembles each paragraph …

Groundwater Research In Middle Earth, Thomas Lapoint

Liberal Arts and Engineering Studies

My senior project focused on studying saltwater intrusion in a coastal town of New Zealand. I feel lucky that I was able to travel to such a distant place, conduct research that was insightful and interesting, and immerse myself in an international culture all in the name of my education. As a Liberal Arts and Engineering Studies student, I aim to analyze not only the cultural differences and similarities that the foreign environment offers to me but also the detailed, technical, engineering aspect of my research. I believe that my education should be approached with a well rounded perspective that …

Seawater/Wastewater Production Of Microalgae-Based Biofuels In Closed Loop Tubular Photobioreactors, Joshua Bradley Lowrey

Master's Theses

The push for alternatives to petroleum fuels has forced researchers to look for highly productive, renewable, non-food resources.  The advantages of using microalgae instead of traditional oil crops for biofuel production include high oil yields, rapid reproductive rates, and versatile growing requirements.  In order to reduce the cost of producing microalgae based biofuels, wastewater has been used as a nutrient source instead of specialized plant nutrients.  The purpose of this study was to compare the relative effectiveness of different combinations of microalgae strain and dairy wastewater for increasing biomass.  The methods for monitoring growth included optical density, cell counting, biomass …

An Inexpensive Method For Creating Paste To Be Used In Paper-Based Microfluidic Devices, Kirra Marie Sankey

Biomedical Engineering

Microfluidic devices are diagnostic tools that are small, portable, and inexpensive. This makes them ideally suited for resource-limited settings. To construct a 3D device, each layer of patterned paper is stacked using double-sided tape with holes corresponding to the pattern. It is necessary to have a paste to fill the holes in the tape and provide a medium for the fluid to wick through. The powder used to make the paste is very expensive and must be bought in bulk (an estimated $1121 - $1231), so it is not convenient for the Biomedical (BMED) department to use. This project was …

Development Of An In-Vitro Hyperglycemic Tissue Engineered Blood Vessel Mimic, Brian C. Wong

Biomedical Engineering

No abstract provided.

A Space Based Particle Damper Demonstrator, John Brown

Master's Theses

The structure and payload of a CubeSat flight experiment that investigates the performance of particle dampers in a micro-gravity environment was designed, built, and tested, and will provide on orbit data for model validation and improved performance predictions for space applications of particle damping.

A 3-D solid model of the integrated CubeSat structure and payload was created satisfying all constraints from CubeSat and the System Dynamics Department at Northrop Grumman Aerospace Systems. The model was verified using commercially available Finite Element Analysis software (FEA), and a prototype structure part was fabricated. The prototype was tested and verified the FEA. A …

Transverse Isotachophoresis Using Polyacrylamide Gel Electrodes, Mark P. Stambaugh

Master's Theses

Separation and isolation of a desired analyte from an impure sample solution containing numerous unwanted interfering agents is the first step of nearly every laboratory test performed in medicine and biology. Nucleic acids are often of particular interest to doctors and researchers, and although methods currently exist for their isolation, these procedures are costly in time, man-power, and real-estate. In addition to easing the execution of presently performed tests, mitigation or elimination of these drawbacks would make a large range of currently unperformed tests both practical and feasible.

This thesis presents a microfluidics-based approach to the isolation of nucleic acids …

The Effects Of A Damage Arrestment Device On The Mechanical Behavior Of Sandwich Composite Beams Under Four-Point Bending, Richard Anthony Davis

Master's Theses

The demand for an insert on composite sandwich structures to aid in the arrestment of face-core delamination is of great need.  This research studies the use of a damage arrestment device (DAD) that connects the carbon fiber face sheets to the foam core to find whether an increase in the structural integrity of the sandwich beam results.  Experimental analysis was employed to test the samples and was verified by a theoretical and finite element approach.

The mechanical properties of LTM45/CF1803 pre-impregnated carbon fiber and Last-A-foam FR 6710 polyvinylchloride foam were experimentally analyzed using ASTM D3039 and ASTM D1621 standards respectively …

Plug-In Hybrid Electric Vehicle Impacts On A Central California Residential Distribution Circuit, Darren Janigian

Master's Theses

The adoption of plug-in hybrid electric vehicles (PHEV) as a means of transportation over conventionally fueled vehicles introduces new challenges to the existing infrastructure of the electrical transmission and distribution system.  PHEV battery charging can represent a significant power demand that has the potential to overload electrical distribution components.  This study examines the impacts of PHEV charging on household service transformers, distribution conductors and voltage levels of a Central California residential distribution system.  The system is simulated using ETAP power system analysis software.  Transformers are the most vulnerable to overloads, especially if PHEV charging occurs in clusters.  Main feeder conductors …

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems.  As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire.  By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Energy Harvesting From Exercise Machines: Forward Converters With A Central Inverter, Nicholas Keith Lovgren

Master's Theses

This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project.  Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid.  This active clamp forward converter boasts a 14V-60V input voltage range and 150W power rating, which closely match the output voltage and power levels from the elliptical trainer.  The isolated topology outputs 51V, higher than previous, non-isolated attempts, which allows the elliptical trainers to interact with a central grid-tied inverter instead of many small ones.  The final converter operated at greater than …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

A Neural Network Receiver For Em-Mwd Communication, Timothy P. Whitacre

Master's Theses

Baseband digital communication in electro-magnetic measurement while drilling (EM-MWD) systems is often corrupted by non-white surface noise. The inability to reliably decode the transmitted signals in a noisy environment limits the depth at which EM-MWD systems can operate. Correlation receivers, which are optimal in the presence of additive white Gaussian noise, can be sub-optimal in the presence of various types of field noise at different drilling sites.

This thesis investigates the application of artificial neural networks (ANN) as communication receivers in EM-MWD baseband digital communication systems. The performances of various ANN architectures and training algorithms are studied and compared with …

Active Pen Input And The Android Input Framework, Andrew S. Hughes

Master's Theses

User input has taken many forms since the conception of computers. In the past ten years, Tablet PCs have provided a natural writing experience for users with the advent of active pen input. Unfortunately, pen based input has yet to be adopted as an input method by any modern mobile operating system. This thesis investigates the addition of active pen based input to the Android mobile operating system.

The Android input framework was evaluated and modified to allow for active pen input events. Since active pens allow for their position to be detected without making contact with the screen, an …

Poroelastic Finite Element Analysis Of A Heterogeneous Articular Cartilage Explant Under Dynamic Compression In Abaqus, Kelsey Kiyo Kam

Master's Theses

A poroelastic finite element model of a heterogeneous articular cartilage disc was

created to examine the tissue response to low amplitude (± 2% strain), low

frequency (0.1 Hz) dynamic unconfined compression (UCC). A strong correlation

has been made between the relative fluid velocity and stimulation of

glycosaminoglycan synthesis. A contour plot of the model shows the relative fluid

velocity during compression exceeds a trigger value of 0.25 μm/s at the radial

periphery. Dynamic UCC biochemical results have also reported a higher

glycosaminoglycan content in this region versus that of day 0 specimens. Fluid

velocity was also found not to be …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

A Pmma Conductivity Pretreatment Microfluidics Device For The Optimization Of Electrokinetic Manipulations, Cameron Paul Purcell

Master's Theses

This project encompasses the design and development of a pretreatment microfluidic device for samples of physiological conductivity, namely a saline solution. The conductivity was reduced through the combination of dilution and ion removal using electric fields to enable downstream electro kinetic manipulations. The two major parts of this project include (1) designing a pretreatment protocol to reduce the conductivity of the sample solution to an acceptable level and (2) designing /fabricating a microchip that will effectively allow aim (1) to be performed on chip.

This project is one of the first to observe the effects of an electric field, used …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

Rfid Classroom Management System, Andrew W. Wright

Master's Theses

Professors who manage large classes are unrealistically expected to grade each student fairly and accurately.  Even with all of the technological advancements that have occurred in the past thirty years, very little progress has been made in classroom management, and as a result, professors are not equipped with enough tools to successfully manage large class sizes.  Because radio frequency identification (RFID) technology is making its way into student issued identification cards, there is an opportunity to use it as a tool to aid professors in the classroom.  The focus of this paper is to discover the most effective system that …

Adaptive Component Usage For The Thermal Management Of Picosatellites, William D. Whalen

Master's Theses

The CubeSat standard originated in 1999.  It was a joint development led by Dr. Jordi Puig-Suari of California State Polytechnic University San Luis Obispo and Professor Robert Twiggs of Stanford University. The engineering challenges that have come from this picosatellite class have created incredible educational opportunities for engineering students throughout the world.  Since the challenges of engineering a CubeSat abound the designers are always looking at novel and even revolutionary solutions to each one.  One of those opportunities is in thermal subsystem design, implementation and characterization.  A potential solution for CubeSats is adaptive component usage.

This thesis is the written …