Development Of Wind Tunnel For Laboratory Wind Turbine Testing, Danny Alexander Zepeda

Electrical Engineering

A wind tunnel with a 0.5 HP motor was purchased by Cal Poly Electrical Engineering Department from Hampden for $16,000. It can only simulate winds of up to 10 MPH. The tunnel has a manual dial that controls the wind speed. It also measures the voltage and current output with an analog measure display. This wind tunnel was expensive and unfortunately cannot achieve very high wind speeds. For this reason, a similar wind tunnel with more potential and with a smaller budget was proposed to be built for use in the Sustainable Energy Lab. The new wind tunnel that was …

Constant Conduction Angle Bias Generation For Monolithic Rf Power Amplifiers, Stephen Garber

Electrical Engineering

There is a need for linear, efficient monolithic power amplifiers used for the wireless transmission of signals with amplitude variations. This paper proposes a circuit that actively biases a bipolar transistor so that it operates as a Class C amplifier, with a conduction angle that is constant over a range of output powers. This results in a linear amplifier with a very low two tone intermodulation distortion. By forcing a scaled DC current vs. input magnitude curve from a Class B amplifier on to a Class C amplifier, a constant conduction angle can be maintained in the Class C amplifier. …

Markerless Affine Region Tracking And Augmentation Using Mser And Sift, Gregory (Greg) Eddington Ii

Computer Engineering

Due to the advancements in mobile computing hardware and the inclusion of cameras in many computing platforms, augmented reality systems have become widely available. This paper presents a real-time implementation of a novel markerless augmented reality algorithm which is able to track two-dimensional affine regions without a priori information of the environment or computing a world model. The implementation consists of the MAR library; a modular software library which performs the region detection, identification, and tracking; and the Lighthouse application; a program which uses the MAR library to allow the user to augment scenes viewed from a camera. The algorithm …

Streaming Client And Server Model, Austin Alan Diec

Computer Engineering

A few years ago, several Cal Poly undergraduates started the Autonomous Robot Platform (ARP). Interest in a revision of the ARP requires a new layer of communication. This paper describes the design and partial implementation of the communication layer to be used with the revised ARP. The communication layer would allow the autonomous robot platform to connect with a client over the wireless local area network (WLAN) for instructions and commands. It is important to note that currently, the assumed revision of the ARP is nonexistent, so many of the design decisions are based solely on the assumptions of ARP …

Variability Of Electroluminescent Displays, Christopher (C.) Michael Shedd, Nathan Ostrout

Graphic Communication

No abstract provided.

Performance Of The Crack, Seat, And Overlay Rehabilitation Technique For Concrete Pavements In California, Reed Calkins

Master's Theses

Research was performed to analyze the performance of the crack, seat, and overlay (CS&O) roadway rehabilitation technique in the Central Coast and Northern regions of California. This technique was evaluated through literature review to determine the state of practice and their conclusions. California highway sections rehabilitated using CS&O were selected for evaluation based on age and location. Pavement distresses and traffic data for these sections were collected and analyzed. Prior to beginning analysis this data was checked for errors, outliers, and omissions. The analysis consisted of checking the data for correlations among distresses and regions.

The focus of this research …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

Design And Assembly Of A Super Treadmill, Simon Iacob

Aerospace Engineering

This report describes the design and construction of an oversized, ruggedized treadmill built for testing heavy loads. The design permits for speed and slope control, as well as a safety tether and emergency stops. The design description is categorized by related systems. The walking belt is powered by an electric motor, which transfers the mechanical rotation via hubs, a linkage belt and rollers. The floor and surface base are sized and designed for proper operation and clearance. The electronics board provides electric power, speed control, and a powered braking system. Safety features are designed for user protection: guard rails, covers, …

Hybrid Rocket Based Combined Cycle Test Rig Design, Construction, And Testing, Mark Costa, Matthew Handfelt

Aerospace Engineering

No abstract provided.

Construction Of Naca 66-415 Nlf Composite Wing For Acoustic Turbulence Testing, Scott Sawyer, Sean Stewart

Aerospace Engineering

A design is developed for a Natural Laminar Flow (NLF) wing, to be used at California Polytechnic State University for acoustic turbulence testing. Composite materials are used to produce high-quality surface finishes necessary for laminar flow. A design for the test apparatus is presented and justified. A manufacturing procedure is proposed for the carbon fiber skin, using Vacuum Resin Infusion (VRI). This procedure is tested on a scaled part with satisfactory results; lessons learned are discovered and integrated into the final manufacturing process. The test section has been fit to the Cal Poly wind tunnel, but full implementation has not …

Cp7 And Datalogger Design And Implementation, Hoang (Mike) Tran

Computer Engineering

No abstract provided.

The Effects Of Heat Treatment On Area Percent Porosity And Corrosion Behavior Of High-Nickel Thermal Spray Coatings, Travis Crowe, Alec Guraydin

Materials Engineering

Samples of two Thermal Spray Coating (TSC) alloys on a low carbon steel substrate were obtained: alloy C276 and Nicko-Shield 200. Specimens of each alloy were subjected to heat treatments at temperatures at 1100° for 60 minutes and 1200° for 10 minutes, with some specimens left in the as-sprayed condition. Three replicates were prepared for each condition. Thin 1” strips were cut using a diamond wafering blade for porosity measurements and 2” x 1” specimens were cut for corrosion testing using a SiC abrasive saw. The porosity specimens were mounted in acrylic resin, polished, and examined using SEM. From these …

Characterization Of A Pdms Microfluidic Reactor For Synthesizing Quantum Dots, Brian Harley

Materials Engineering

A PDMS microfluidic reactor was made in Cal Poly’s class 1000 clean room for the purpose of synthesizing quantum dots.  The device master mold was made from a silicon substrate and SU-8 features 50μm tall.  The PDMS reactor was cast from that mold.  The flow rates of fluid through the channels, heating of the reactor and pressure in the reactor were measured in order to characterize the potential for synthesizing quantum dots.  Flow rates of 20 mL/hr through 4 mL/hr were tested to characterize the consistency of amount of time the fluid remains in the reactor at a constant flow …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Characterization Of The Oxidation Kinetics Of Fecral Ferritic Stainless Steels At 900°C For Catalytic Converter Applications, Stacy Stamm

Materials Engineering

This study characterized the oxidation kinetics of two types of ferritic stainless steel foils used as substrates for catalytic converters. Catalytic converters rely on an alumina layer on the surface of the foils, which allows the catalyst to attach to the substrate. Because the alumina layer is so important, this study characterized the weight gain, thickness, and composition of the alumina as it grew at 900°C for up to 400 hours. The two foils characterized were an MK foil, used for gasoline engines, and an EMS foil, used for diesel engines. The MK foil showed a percent weight gain of …

Design, Construction And Evaluation Of An Automotive Bridge Jack, Thomas Gomes Jr.

BioResource and Agricultural Engineering

This Senior Project discusses the design, construction and evaluation of an automotive lift. This lift will be hydraulically powered with a 6000 lb lifting capacity. The lift constructed in this project will be installed within a current 4 post drive on vehicle lift and allows the user to lift one axle of a vehicle a few inches off the ramp of the drive on lift in order to remove the tires.

Optimization And Modeling Tools For Telescope Hexapod Structures, Michael Edward Feeney

Master's Theses

Hexapod trusses are an important element in many mechanical design systems. The natural frequency and stiffness behavior under geometric and mass variations of such structures is largely undocumented. Furthermore, the ability to quickly model hexapod designs and explore a large design-space in finite element software packages is, in general, time consuming and inefficient. The purpose of this project was to develop software tools that made design-space exploration (modeling and simulation processes) for hexapod structures drastically more efficient. Secondly, the project included an experimental analysis portion to demonstrate the various modal study techniques and to validate finite element analysis predictions. Lastly, …

Low-Power Self-Sustaining Schedule Display, Samuel (Sam) August

Electrical Engineering

The completed project is an Amazon Kindle, powered by a USB solar charger, running a student designed program to display a weekly schedule for a faculty member.  The purpose of the project was to design a sustainable electronic schedule display for use outside a faculty office.  It was designed in the hopes that faculty members could more easily update their schedules, and possibly allow for students to schedule appointments.  The program was designed using Java and the solar-charger was designed using a solar cell, Schottky diode, and a USB to micro-B USB cable.

Current Tracking Power Supply For Sensor Calibration, Joshua Brookley

Electrical Engineering

This report highlights the steps taken to design and develop a constant 5V power supply capable of tracking load current. The background of its previous design, its necessary specifications and steps taken to achieve specifications are highlighted throughout the report. The report also contains conclusions and final recommendations for the design chosen, including its strengths and drawbacks.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Dyl-Light: An Acn Controlled, Rgbw Led Light Fixture, Dylan Pavelko

Electrical Engineering

The Dyl-Light is a LED lighting fixture that is controlled with a recently released suite of entertainment technology protocols called A.C.N. This new protocol has a number of advantages to its use over the existing protocol, DMX512, used for controlling entertainment lighting fixtures. This project attempts to use this new protocol to directly control a light fixture, something that currently is not available on the market.

The project includes several aspects of engineering from electronics, embedded systems, applications, networking, power electronics, and computer interfacing.

Heart-Rate Monitoring Control System Using Photoplethysmography (Ppg), Wesley Nguyen, Ryan Horjus

Electrical Engineering

No abstract provided.

Discrete Alarm Clock, Travis Moore, Collin Barth

Electrical Engineering

The standard alarm clock, as used daily by millions worldwide, has clear room for modification and improvement.  This paper documents an implementation that rectifies many of these flaws.  Improvements include adjustable snooze length, an IR remote for ease of use, and an RF headset for discrete alarm use or potential incorporation into a device much like a hearing aid.  The processes involved in creating a digital alarm clock, as well as the obstacles met in the implementation of the enhanced design, are detailed within.

Mp3 Player System Design, Eric Wu

Electrical Engineering

The purpose of this project is to design and build a portable audio player that reads music files off an SD card, decodes the music file and outputs the music through a headphone jack.  A microcontroller running FreeRTOS will facilitate the data transfer between an SD card and the decoding chip.  The decoded audio will then be sent to a high-end DAC chip that outputs the sound.

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments.  There is good reason for this, too.  In the State of California, office buildings represent the single largest user of energy in the commercial sector.  This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations.  The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Rfid Home And Office Automation System: Based On Localized Room Entry, Nolan Clark

Electrical Engineering

Design and build a proof of concept model demonstrating an application of Radio Frequency Identification (RFID) technology for use in a home or office lighting automation system. The system provides new means for reducing energy consumption through active light switching based on simplified location tracking. Often lighting systems use motion sensors and timers to determine when a person enters or leaves a room, but these platforms are based purely on motion meaning “no motion, no light.” The RFID based system utilizes medium range RFID readers and tags located at doorways or narrow passageways in the environment to provide a general …

Design Strategy For A 3-Phase Variable Frequency Drive (Vfd), Omar David Munoz

Electrical Engineering

This paper describes the design processes for a 3-Phase Variable Frequency Drive (VFD) as broken up into two stages: The AC-DC converter and the DC-AC converter. It acknowledges three (3) design versions, all. The output of the motor drive is 3-phase pulse width modulation (PWM) ranging in possible operation frequencies from 0Hz to 13kHz. The frequency control circuit uses an Arduino Uno based of the ATMEGA 328p.

Building Balls: Final Design Report, Jumpsport Inc., Gary Johnson, Rosalie Mangione, Steven (Steve) Rose

Mechanical Engineering

JumpSport, a major trampoline company, has requested Cal Poly to design a custom play-structure consisting of large diameter balls with two types of connectors-long rod connections and very close connectors (for a ball-to-ball type connection).  By the end of the project, appropriate testing will be carried out on the connections and a full-scale model will be constructed.

After an extensive design process, our team of three decided on a rod connection style for both the long and short connectors.  These consist of a hook that latches into a loop protruding from the ball where the hook is attached by a …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …