Engineering Commons^™

A New Undergraduate Laboratory Course In Magnetic Design, Taufik Taufik, Scott Mcclusky, Jonathon Paolucci, Dale S. Dolan

Electrical Engineering

This paper presents a set of new laboratory experiments developed in conjunction with an undergraduate course in magnetic design. The course has recently been reintroduced as a technical elective course where students learn the basics of inductor and transformer design. Five new laboratory experiments have been developed to cover magnetic concepts and to provide students with the hands-on experience in designing and building magnetic components. The paper presents an overview of the course, and highlights the new lab experiments in the course.

Development Of Wind Tunnel For Laboratory Wind Turbine Testing, Dale S. Dolan, Danny Zepeda, Taufik Taufik

Electrical Engineering

This paper presents the development of a wind tunnel that will be used for wind turbine testing in a controlled environment. The prototype is designed to be able to provide wind speeds of up to 20 m/s (~43mph) depending on the cross sectional area of the tunnel chamber. A 42 inch tube axial fan is driven by a 5hp induction motor using a variable frequency drive to allow continuously variable wind speeds from near zero up to the maximum wind speed. The fan is rated to produce ~25,000 CFM and the corresponding wind speed is therefore dependent on chamber cross …

Forward Osmosis Bag: Ground Testing The Prospect Of Using Alternative Water Sources For Drinking Water, Michaela Marie Brant, Ariella Yendler, Mona Hammoudeh, Michael T. Flynn

STAR Program Research Presentations

On the STS-135 Space Shuttle mission, to be launched July 8, 2011, a forward osmosis bag (FOB) study will be conducted. At NASA Ames this summer, the ground truth testing is being conducted for results comparisons. The FOB technology is derived from a commercial product, the X-Pack water filter. Forward osmosis operates by utilizing an established concentration gradient across a semi-permeable membrane to move water molecules from one side of the membrane to the other. This concept is exploited to harvest drinking water from grey water sources such as urine, sea water, or vehicle water. In this experiment, potassium chloride …

Assessing Laser Lifetime Test Performance, Joe Weichman, Hamid Hemmati, Malcolm Wright

STAR Program Research Presentations

Assessing expected component lifetime is necessary in developing instruments for future space-flight projects to ensure long term operation in the challenging environment. Although semiconductor diode lasers have widespread use in terrestrial applications, their use in space is still an emerging technology that requires on-going testing to demonstrate their capability. The project called for re-establishing the test setup for assessing lifetime performance of 20 continuously running 200mW 830 nm diode lasers. These lasers underwent previous testing based on parameters for NuSTAR’s laser metrology system, and met the six month lifetime project requirements under nominal operating conditions. Laser testing is currently underway …

Sitting In The Pilot's Seat: Optimizing Human-Systems Interfaces For Unmanned Aerial Vehicles, Steven Michael Queen, Kurt Sanner

STAR Program Research Presentations

One of the pilot-machine interfaces (the forward viewing camera display) for an Unmanned Aerial Vehicle called the DROID (Dryden Remotely Operated Integrated Drone) will be analyzed for optimization. The goal is to create a visual display for the pilot that as closely resembles an out-the-window view as possible. There are currently no standard guidlines for designing pilot-machine interfaces for UAVs. Typically, UAV camera views have a narrow field, which limits the situational awareness (SA) of the pilot. Also, at this time, pilot-UAV interfaces often use displays that have a diagonal length of about 20". Using a small display may result …

Design, Fabrication, And Characterization Of A Thin-Film Nickel-Titanium Shape Memory Alloy Diaphragm For Use In Micro-Electro-Mechanical Systems, Brian Joel Alvarez

Master's Theses

Previous work done at Cal Poly has shown that thin-film nickel-titanium (NiTi) can be easily sputtered onto silicon wafers and annealed to create a crystallized shape memory alloy (SMA) film. Initial work on creating devices yielded cantilevers that were highly warped due to thin-film stress created during the sputtering process. The objective of this work was to create a thin-film NiTi SMA device that could be better characterized. A membrane was selected due to the simplicity of fabrication and testing which would also oppose the thin-film stress due to the increase in attachment points to the substrate.

Silicon wafers were …

Quantitative Characterization Of Microstructure Features For 1st Generation Advanced High Strength Steels, Margarita Vidrio, Ellen Liu, Donsheng Li, Kyoo Sil Choi, Xin Sun

STAR Program Research Presentations

The role of Advanced High Strength Steels (AHSS) in the automotive industry is important because of its affordability and excellent mechanical properties. The 1st generation of AHSS achieves its preferred combination of strength and ductility by embedding harder martensite grains into softer ferritic matrix. Ductility and strength of these steels are important to safety, formability, application, and life. However, a noticeable degree of inconsistent forming behaviors has been observed in the 1st generation AHSS in production, which seems to be related to the microstructure-level inhomogeneity. The objective of this project is to grain fundamental understandings on how different microstructure level …

Simulation Of Wing Tip Vortices, Ryan Termath, Jason Lechniak, Keerti Bhamidipati

STAR Program Research Presentations

Modeling and Simulation (M&S) computational fluid dynamics (CFD) techniques were used to better understand wing tip vortices about a wing section. The CFD results were compared to experimental wind tunnel data derived from the University of Iowa (Ref. 2). The experiment used Stereoscopic Particle Image Velocimetry (SPIV) to measure the flow field. The SPIV data from the experiment illustrates the vortex core development and behavior downstream of the trailing edge of the wing section. Three CFD simulations using various mesh sizes and time steps were completed and compared to the experimental results. Two dimensional plots of modeled local flow field …

Effect Of Au Content On Microstructural Evolution Of Snagcu Solder Joints That Undergo Isothermal Aging And Reliability Testing, Patrick J. Hyland

Master's Theses

Electronics, especially, printed circuit boards (PCBs) are a widespread technology. Metal coatings or “surface finishes” are often added to PCB board pads and component leads during manufacturing to improve their performance. Electroplated nickel/gold over copper is a popular surface finish for printed circuit boards and component leads. The presence of gold in solder joints, however, is known to have detrimental effects referred to as gold embrittlement. It is generally understood that tin-lead solder joints with less than 3 weight percent (wt%) of gold will not experience reliability issues. The acceptable level of gold in lead-free solder joints, however, is less …

Decisive Disaster Debris Management, Nazli Yesiller

Civil and Environmental Engineering

No abstract provided.

Morphology Changes In Pcpdtbt:Pcbm And P3ht:Pcpdtbt:Pcbm And Its Effect On Polymer Solar Cell Performance, Galen David Cauble

Physics

Polymer solar cell morphology is sensitive to both heat and time. By thermally annealing polymer solar cells the morphology of the devices can be altered causing immediate changes in device performance. Blending PCPDTBT:PCBM with P3HT:PCPDTBT combines the absorption characteristics of each to create a more even absorption spectrum. Subjecting PCPDTBT:PCBM, and P3HT:PCPDTBT:PCBM polymer solar cells to thermal annealing as well as recording device performance through time has shown that P3HT:PCPDTBT:PCBM devices react positively to thermal annealing (increasing from 0.8% to 1.4%) while PCPDTBT:PCBM devices have varied reactions. Furthermore, the P3HT:PCPDTBT:PCBM devices have achieved efficiencies of 1.6% in AM 1.5 compared …

Structural Analyses Of Wind Turbine Tower For 3 Kw Horizontal Axis Wind Turbine, Tae Gyun Gwon

Master's Theses

Structure analyses of a steel tower for Cal Poly's 3 kW small wind turbine is presented. First, some general design aspects of the wind turbine tower are discussed: types, heights, and some other factors that can be considered for the design of wind turbine tower. Then, Cal Poly's wind turbine tower design is presented, highlighting its main design features. Secondly, structure analysis for Cal Poly's wind turbine tower is discussed and presented. The loads that are specific to the wind turbine system and the tower are explained. The loads for the static analysis of the tower were calculated as well. …

Characterizing Nerve Fiber Activation By Varying Fiber Diameter And Depth Within A Conductive Medium: A Finite Element Approach, Nathan Daniel Soto

Master's Theses

In some instances neuropathies can be diagnosed through a conduction velocity test. However, not all neuropathies can be classified using this method. Gaining an understanding of how the stimulus level varies for different fiber sizes at different fiber depths within a conductive medium will provide useful information for simulation studies.

Following a two-step approach using COMSOL and MATLAB, a simulation was implemented to investigate the stimulus necessary to activate different sized fibers at different depths. In this two-step approach, COMSOL was used to describe the voltage profile that would be present within a conductive medium after a stimulus was applied. …

Constant Conduction Angle Experimental Generation For Rf Power Amplifiers, Michael Spahn

Electrical Engineering

As the demand for more devices to become wireless increases, there is a need for linear, efficient monolithic power amplifiers to deal with the variations in modulation of signals. With partial support from Cal Poly C3RP Grant #52268, this paper explains the implementation of and analyzes a circuit that actively biases a bipolar transistor to operate as a Class C amplifier. The Class C amplifier can maintain constant conduction angle over a range of output powers by using a Class B amplifier to force a scaled DC current vs. input magnitude curve on to a Class C amplifier. The knee …

Design, Construction And Evaluation Of Seven Shank, Three Point Ripper, Daniel Degraaf

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and testing of a seven shank, three point ripper built for de Graaf Ranch. This ripper will replace older equipment that was not built to withstand the horsepower developed by more modern tractors that are used by de Graaf Ranch. This tillage device is designed to meet ASABE standards for horsepower requirements of farm equipment. This implement incorporates a shear pin design that will protect the frame from damage in the event that the ripper encounters a subsoil obstacle that would significantly damage the equipment. The shank was designed to reduce the disturbance …

Wireless Passive Power Transfer Using Wire Antennas, Sheng Da Zhang

Electrical Engineering

This project tests and analyzes the efficiency of directional and omnidirectional antennas in wireless power transfer for charging. The project demonstrates the steps of construction and properties of dipole, monopole, and Yagi Uda antennas. A low power high frequency DC rectifier circuit converts the received RF power from the antenna and stored it as DC voltage on a capacitor. The receiver circuit also estimates the power received by the antenna. Wireless RF power transmission proves to be inefficient for short distances. The best efficiencies of the antennas were under 50% even at 0.1meter. The near field attenuation starts at around …

140 New Montgomery Power Distribution Design, Stephen Shaffer

Electrical Engineering

The Power Distribution Design for a high-rise building requires a great deal of coordination and design from the structural, electrical, mechanical, telecommunication, and PG&E engineers. This report will cover how I was able to coordinate and design the power distribution system for 140 New Montgomery, a 28 story building located in San Francisco. Furthermore, this report will cover the steps taken in the future to ensure a smooth transition from the schematic design phase to the construction document phase.

902–928mhz Uhf Rfid Tag Antenna Design, Fabrication And Test, Chiweng Kam

Master's Theses

Radio Frequency Identification (RFID) uses RF radiation to identify physical objects. With decreasing integrated circuit (IC) cost and size, RFID applications are becoming economically feasible and gaining popularity. Researchers at MIT suggest that RFID tags operating in the 900 MHz band (ultrahigh frequency, UHF) represent the best compromise of cost, read range, and capabilities [1]. Passive RFID tags, which exclude radio transmitters and internal power sources, are popular due to their small size and low cost [1].

This project produced Cal Poly’s first ever on-campus printed, assembled, and operational UHF (902 to 928 MHz) passive RFID tag. Project goals include …

Unsteady Total Pressure Measurement For Laminar-To-Turbulent Transition Detection, Akane Sharon Karasawa

Master's Theses

This thesis presents the use of an unsteady total pressure measurement to detect laminar-to-turbulent transition. A miniature dynamic pressure transducer, Kulite model XCS-062-5D, was utilized to measure the total pressure fluctuations, and was integrated with an autonomous boundary layer measurement device that can withstand flight test conditions. Various sensor-probe configurations of the Kulite pressure transducer were first examined in a wind tunnel with a 0.610 m (2.0 ft) square test section with a maximum operational velocity of 49.2 m/s (110 mph), corresponding dynamic pressure of 1.44 kPa (30 psf). The Kulite sensor was placed on an elliptical nose flat plate …

Foce Medium Voltage Load Switcher, Eric Nelson, Sean Tolibas

Electrical Engineering

No abstract provided.

Updating Purchasing Specifications For Energy-Efficient Commercial Boilers For The Federal Energy Management Program, Arturo Avila, James Lutz

STAR Program Research Presentations

The Federal Energy Management Program (FEMP) and the Environmental Energy Technology Division (EETD) at Lawrence Berkeley National Laboratory (LBNL) are conducting a research project that aims to update the current purchasing specification for energy-efficient commercial boilers. Data available on the internet was used to document the efficiencies, prices and other relevant data on commercial boilers. Boiler models were classified according to their fuel use (gas or oil) and if they produced hot water or steam. Boilers were ranked from highest to lowest thermal efficiency. Scatter plots were used to assess the ranges of efficiencies over a range of boiler capacities …

Effect Of Processing, Packaging And Vibration Treatment On The Sensory Quality Of Fresh-Cut Apple Slices, M. Siddiq, J. B. Harte, S. P. Singh, A. A. Khan, K. D. Dolan, Koushik Saha

Industrial Technology and Packaging

Fresh-cut fruit industry has seen tremendous growth in recent years. The present study was designed with the objective of studying the sensory quality of fresh-cut apple slices that were treated with different antibrowning agents, packed in three types of packaging materials and subjected to vibration treatment to simulate commercial transportation. The slices were treated with two commercial antibrowning agents [NatureSeal (Mantrose-Haeuser Co., Inc., Westport, CT, USA) and Ever-Fresh (Kraft Foods, Inc., Rye Brook, NY, USA)] at 5% (w/v) application rate. The treated slices were packaged in 5 oz polystyrene rigid container, 2 lb polyethylene bag or 2 oz polyethylene bag. …

Reliable Ethernet, Aleksandr Movsesyan

Master's Theses

Networks within data centers, such as connections between servers and disk arrays, need lossless flow control allowing all packets to move quickly through the network to reach their destination. This paper proposes a new algorithm for congestion control to satisfy the needs of such networks and to answer the question: Is it possible to provide circuit-less reliability and flow control in an Ethernet network? TCP uses an end-to-end congestion control algorithm, which is based on end-to-end round trip time (RTT). Therefore its flow control and error detection/correction approach is dependent on end-to-end RTT. Other approaches utilize specialized data link layer …

Benefits Of Near-Term Cloud Location Forecasting For Large Solar Pv, Timothy Robert Rudd

Master's Theses

As the ‘green’ energy movement continues to gain momentum, photovoltaic generation is becoming an increasingly popular source for new power generation. The primary focus of this paper is to demonstrate the benefits of close-to real-time cloud sensing for Photovoltaic generation. In order to benefit from this close-to real-time data, a source of cloud cover information is necessary. This paper looks into the potential of point insolation sensors to determine overhead cloud coverage. A look into design considerations and economic challenges of implementing such a monitoring system is included. The benefits of cloud location sensing are examined using computer simulations to …

Face Detection And Lip Localization, Benafsh Nadir Husain

Master's Theses

Integration of audio and video signals for automatic speech recognition has become an important field of study. The Audio-Visual Speech Recognition (AVSR) system is known to have accuracy higher than audio-only or visual-only system. The research focused on the visual front end and has been centered around lip segmentation. Experiments performed for lip feature extraction were mainly done in constrained environment with controlled background noise. In this thesis we focus our attention to a database collected in the environment of a moving car which hampered the quality of the imagery.

We first introduce the concept of illumination compensation, where we …

Full Custom Vlsi Design Of On-Line Stability Checkers, Chris Y. Lee

Master's Theses

A stability checker is a clocked storage element, much like a flip-flop, which detects unstable and late signals in the pipeline of a digital system. The On-line stability checker operates concurrently with its associated circuit-under-test (CUT). This thesis describes the full custom very-large-scale integration (VLSI) design and testing process of On-Line Stability Checkers. The goals of this thesis are to construct and test Stability Checker designs, and to create a design template for future class projects in the EE 431 Computer-Aided Design (CAD) of VLSI Devices course at Cal Poly.

A method for concurrent fault testing called On-line Stability Checking …

Equivalent Circuit Implementation Of Demyelinated Human Neuron In Spice, Nathan A. Angel

Master's Theses

This work focuses on modeling a demyelinated Hodgkin and Huxley (HH) neuron with Simulated Program with Integrated Circuit Emphasis (SPICE) platform. Demyelinating disorders affect over 350,000 people in the U.S and understanding the demyelination process at the cellular level is necessary to find safe ways to treat the diseases [9]. Utilizing a previous SPICE model of an electrically small cell neuron developed by Szlavik [32], an extended core conductor myelinated neuron was produced in this work. The myelinated neuron developed has seven active Nodes of Ranvier (nodes) separated by a myelin sheath. The myelin sheath can be successfully modeled with …

Lip Localization Algorithm Using Gabor Filters, Robert E. Hursig, Jane Xiaozheng Zhang, Chiweng Kam

Electrical Engineering

This paper describes a lip localization algorithm within a still image frame for subsequent tracking and audiovisual speech recognition processing. A Gabor filter-based feature space is promoted as a means to localize lips within an image based off of shape. This filtered space is shown to effectively differentiate facial features, including lips, from their backgrounds and to bound the full extent of the lips within a face-classified region of interest. Extensive training and test sets are used to justify design decisions and performance.

Green Building Policy, School Performance, And Educational Leaders’ Perspectives In Usa, Scott D. Kelting, Michael Montoya

Construction Management

The movement to construct high performance “green” buildings has had unprecedented market growth and continues to become mainstream practice for constructing schools in the United States. Green schools have economic, environmental and health benefits. Research provides information on the use of increased student performance found in green schools to justify building schools to a higher standard of indoor environment quality. There is clear and compelling evidence that schools currently built to specific green standards of indoor environmental quality, (e.g. thermal comfort, indoor air quality, acoustics and lighting,) result in healthier and more productive students and teachers. Current green building policies …

Aperture Coupled Patch Antenna Design Methods, Michael Civerolo, Dean Arakaki

Electrical Engineering

Microstrip patch antennas have been used extensively in applications requiring low-profile, mounting structure conforming, and low-cost wireless communications. Feed methods (antenna-transmission line interface) are critical for optimum performance. The aperture coupled technique exhibits reduced transmission line radiation and enhanced antenna radiation and co- to cross-pol performance relative to microstrip and probe fed configurations. Researchers have focused on analytical methods and design improvements without identifying parametric tradeoffs or design methods. Hence, this paper presents theoretically and parametrically identified critical antenna dimensions and performance effects, and a design procedure to convert desired performance requirements into operational prototypes.