Engineering Commons^™

An Alternative Dual-Launch Architecture For A Crewed Asteroid Mission, Steven M. Korn

Master's Theses

This thesis is a feasibility study for a crewed mission to a Near Earth Asteroid (NEA). An alternate dual-launch architecture is proposed and analyzed against a more established architecture. Instead of a rendezvous in a low-Earth parking orbit, the new architecture performs the rendezvous while the two spacecraft are on an Earth-escape trajectory to the destination NEA. After selecting a target asteroid, 2000 SG344, each architecture will have its best mission compared to the best mission of the other architecture.

Using the new architecture, a mission is created to the chosen NEA, 2000 SG344. A back-up Orion MPCV and a …

The New Bicycle Model: Introducing Software Considerations Early Into The Systems Engineering Design And Integration Process, Nathaniel Dinglasan Angat

Master's Theses

Lockheed Martin Space Systems Company, Sunnyvale, California is in the business of designing and engineering satellites for commercial and government customers. This task is by no means a trivial endeavor but Lockheed MartinSunnyvale has many decades of experience in Systems Engineering. Training in systems engineering is a long process whose training tools must be kept up-to-date and appropriate as new advances in technology evolve along-side with the processes that develop these ever-evolving solutions. For many years new systems engineers have been introduced to the Bicycle Model as a paradigm for designing and developing complex systems that are composed of diverse …

Sbx7 Flow Rate Measurement Compliance For Agricultural Irrigation Districts, Charles M. Burt, Evan Geer

BioResource and Agricultural Engineering

Senate Bill x7-7 (SBx7-7) requires documented volumetric accounting to individual turnouts for water deliveries. Section 597.3 of the bill lists two very different requirements for devices. This document examines the requirements of SBx7 and the implications for agricultural irrigation districts. The definitions and impacts of flow rate and volumetric accuracy are defined. Example scenarios and solutions are offered, as well as descriptions of applicable devices.

Empirical Model For The Transconductance-Current Dependence Of Short-Channel Mosfets, Vladimir I. Prodanov

Electrical Engineering

This work is concerned with the g_m-I dependence of sub-micrometer MOSFETs. The transconductance-current expression given by the Advanced Compact Model (ACM) is reviewed and simple modification is proposed. The modification yields an expression which (with proper parametrization) captures the g_m-I dependence of short-channel MOSFETs. The proposed expression is “universal” in the sense that it is capable of modeling the g_m-I dependence of long-channel MOSFETs, short-channel MOSFETs, and resistively-degenerated BJTs.

Electric Currents Due To Stress-Activated Positive Hole Charge Carriers In Ice, Cary T. Keller P.E., Friedemann T. Freund, Dale P. Cruikshank

STAR Program Research Presentations

Jupiter’s satellite Europa, whose surface is composed of ice with a possible water ocean beneath, could conceivably serve as an abode for extraterrestrial life. This and other icy celestial bodies may contain organic macromolecular solid material that is produced when surface ices are exposed to ultraviolet radiation and/or electrical energy. Tidal and tectonic stresses or meteorite impacts in icy crusts may produce electrical discharges, which would provide the energy for in-situ synthesis of the organic solids. This electrical energy can be provided by positive hole charge carrier activation. Positive holes exhibit properties such as the ability to flow out of …

Technology Portal For Energy Efficient Buildings, Larry D. Hermanson, Daniel Studer, Annie Mroz

STAR Program Research Presentations

Project: Technology Portal for Energy Efficient Buildings

Date: August 2, 2012

Author: Larry Hermanson

Mentor: Daniel Studer

Cohort: Annie Mroz

Lab site: National Renewable Energy Laboratory (NREL)

Buildings account for 71% of the electricity demand and 39% of the primary energy consumption in the United States. The Commercial Buildings Group at NREL provides builders, designers and building owners accurate information to significantly improve the energy efficiency of new and existing buildings. The Technology Portal for Energy Efficient Buildings will increase the accessibility of standardized and credible energy performance data for all building systems, thereby allowing building owners to better evaluate …

Graphene Refinement By High Temperature Anneals, Benjamin A. Calvopina, Justin Bult, Jeff Blackburn

STAR Program Research Presentations

Graphene’s intrinsic properties of being a good conductor as well as having efficient optical transmission make it a potentially useful material in photovoltaic cells as a transparent conducting electrode. One problem preventing graphene from being fully utilized stems from contaminates created and deposited during the transfer process of multiple graphene layers. After synthesis, TRT (Thermal Release Tape) is applied to the graphene supported on the copper growth substrate. TRT utilizes a unique formulation of adhesive that is temperature sensitive so that it will release when heated. Upon removing the growth substrate in a chemical bath, the TRT is used to …

Telescope Assembly Alignment Simulator Performance Optimization, Joshua G. Thompson, Brian Eney, Zaheer Ali, Bob Thompson

STAR Program Research Presentations

The Telescope Assembly Alignment Simulator (TAAS) calibrates scientific instruments (SI’s) that are installed on the Stratospheric Observatory For Infrared Astronomy (SOFIA). An SI’s accuracy is directly dependent on the consistent performance of the TAAS, which has never been fully characterized. After designing various thermal and optical experiments to identify the current unknowns of TAAS, we now have a far better grasp on how the equipment behaves.

The Effect Of Stretch Wrap Pre-Stretch On Unitized Load Containment, Evan A. Cernokus

Master's Theses

There are three main factors affecting the stability of a palletized load that is unitized by a stretch wrapping mechanism. These factors include the type of unitized load, wrapping configuration and shipping method. The wrapping configuration is determined on the basis of the type of unitized load and shipping method. For this study, the aforementioned components were referred to as the package, the product, and the distribution environment. These components come together to make up a stretch wrapping system. The package corresponds to the stretch wrap film that is packaging the unitized load and pallet. The product corresponds to the …

Selective Laser Sintering; A Design Of Experiments, Philip David Hopkins, Victor Castillo Phd

STAR Program Research Presentations

Additive Manufacturing (AM), also commonly known as 3D Printing or Rapid Prototyping, is a method of manufacturing that provides for the ability to make intricate internal features and easily customizable parts. The concept is to break a Computer Aided Design (CAD) file into a series of thin layers that are sent to the machine and laid down one layer at a time. Just like any other form of processing, material properties can alter by undergoing this process. Manipulating various parameters of the AM process can allow for different properties to be achieved. For this reason, an in depth study will …

Commissioning Of The Asta Laser Lab With Uv Pulse Length Characterization, Daniel Kelley, Jeff Corbett

STAR Program Research Presentations

The Linac Coherent Light Source (LCLS) at SLAC depends on a photocathode electron gun to provide the linear accelerator with the raw material – electrons – used for making X-ray laser pulses. The photocathode used in the LCLS Injector is a clean copper plate in high vacuum. When the cathode is struck with high energy UV light, electrons are liberated from its surface and then accelerated down the linac with radio-frequency electric fields. These fast-moving bunches of electrons are directed through an undulator magnet to radiate X-ray light.

Although scientists have been using photocathode techniques at SLAC for 25 years, …

Two-Stage, High-Altitude Rocket With Internal Skeleton Design Entered In Advance Category Of 7th Esra Irec, Samuel S. Bowman, Kevin J. Byrne, Allen Capatina, Aliki S. Loper-Leddy, Joshua A. Van Schoyck

Aerospace Engineering

A high-altitude, two-stage rocket was designed, built, and entered in the advanced category of the 7^th Annual Experimental Sounding Rocket Association (ESRA) Intercollegiate Rocketry Engineering Competition (IREC). The rocket, called AJAKS, featured an internal skeleton made of carbon fiber rods, and a combination of plywood, carbon, and aluminum bulkheads. Loads were driven through the internal structure, with an outer skin tube providing an aerodynamic surface. A unique separation device was developed to ensure proper stage separation. The competition required the rocket to carry a 10-lb payload, which was chosen by the team to consist of an IMU and data …

Effects Of Sprinkler, Partial Sprinkler/Drip, And Drip Only Irrigation On Strawberry Transplants 2011-2012, Stuart Styles

BioResource and Agricultural Engineering

The Cal Poly Irrigation Training and Research Center (ITRC), in collaboration with academic, water district, and industry partners, proposes to evaluate new strategies for drip irrigation on strawberries to minimize runoff during transplant establishment.

The most common method used for irrigating strawberries is a mix of sprinkler irrigation and drip. Growers use sprinkler irrigation for bed preparation and salinity control, then eventually switch to drip irrigation after transplanting, but continue to use sprinkler irrigation as an insurance policy (for bonding between plant roots and soil bonding, washing off the leaves, controlling salinity, and frost). However, field observations have shown that …

Investigation Of Spillover Effect To Enhance Hydrogen Storage, Sarah C. Corrigan, Lin Simpson, Thomas Gennett

STAR Program Research Presentations

Hydrogen is an attractive energy option because of its low
environmental impact, but a critical problem is its low energy
density, which makes it difficult to store. For example, the US
Department of Energy (DOE) hydrogen plan for fuel cell powered
vehicles requires a gravimetric density of 6.5 wt%. There are several
existing hydrogen storage methods, including compressed gas,
liquefaction, metal hydrides, and physisorption, but at present, none
of these technologies comes close to achieving the targets set by the
DOE. Although chemical storage methods have been claimed to be the
most promising hydrogen storage technology, and activated carbons the …

Optical Mode Study Of Galium Nitride Based Laser Diodes, Douglas Cattarusa

Electrical Engineering

This paper focuses on the optical mode analysis of laser diodes to improve light emission. Under the mode analysis, we compare the optical confinement factor (OCF) percentage of the emitting light from the LDs. There are two structures which we analyze: a basic GaN waveguide structure and an InGaN waveguide structure. The second structure has additional InGaN waveguides and is analyzed under two additional design variations: the concentration of Indium and the thickness of the top waveguide layer. The results of this study indicate introducing InGaN waveguide layers correlates with lower order modes (zero and first order) and increase the …

Static Balancing Of The Cal Poly Wind Turbine Rotor, Derek Simon

Master's Theses

The balancing of a wind turbine rotor is a crucial step affecting the machine’s performance, reliability, and safety, as it directly impacts the dynamic loads on the entire structure.

A rotor can be balanced either statically or dynamically. A method of rotor balancing was developed that achieves both the simplicity of static balancing and the accuracy of dynamic balancing. This method is best suited, but not limited, to hollow composite blades of any size. The method starts by quantifying the mass and center of gravity of each blade. A dynamic calculation is performed to determine the theoretical shaking force on …

Control System Development For Small Uav Gimbal, Nicholas J. Brake

Master's Theses

The design process of unmanned ISR systems has typically driven in the direction of increasing system mass to increase stabilization performance and imagery quality. However, through the use of new sensor and processor technology high performance stabilization feedback is being made available for control on new small and low mass stabilized platforms that can be placed on small UAVs. This project develops and implements a LOS stabilization controller design, typically seen on larger gimbals, onto a new small stabilized gimbal, the Tigereye, and demonstrates the application on several small UAV aircraft. The Tigereye gimbal is a new 2lb, 2-axis, gimbal …

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Accelerating Ray Casting Using Culling Techniques To Optimize K-D Trees, Anh Viet Nguyen

Master's Theses

Ray tracing is a graphical technique that provides realistic simulation of light sources and complex lighting effects within three-dimensional scenes, but it is a time-consuming process that requires a tremendous amount of compute power. In order to reduce the number of calculations required to render an image, many different algorithms and techniques have been developed. One such development is the use of tree-like data structures to partition space for quick traversal when finding intersection points between rays and primitives. Even with this technique, ray-primitive intersection for large datasets is still the bottleneck for ray tracing.

This thesis proposes the use …

The Effect Of A Low-Velocity Impact On The Flexural Strength And Dynamic Response Of Composite Sandwiches With Damage Arrestment Devices, Kodi A. Rider

Master's Theses

Impact strength is one of the most important structural properties for a designer to consider, but is often the most difficult to quantify or measure. A constant concern in the field of composites is the effect of foreign object impact damage because it is often undetectable by visual inspection. An impact can create interlaminar damage that often results in severe reductions in strength and instability of the structure. The main objective of this study is to determine the effectiveness of a damage arrestment device (DAD) on the mechanical behavior of composite sandwiches, following a low-velocity impact. A 7.56-lb_f crosshead …

An Experimental Investigation Of A Goldschmied Propulsor, Joshua Roepke

Master's Theses

A wind tunnel investigation of an axisymmetric bluff body, known as a Goldschmied propulsor, was completed. This model conceptually combines boundary layer control and boundary layer ingestion into a single complementary system that is intended to use energy to reduce the axial force on the body by eliminating separation and increasing the pressure recovery aft of the body’s maximum thickness. The goal of the current project was to design, fabricate, and fully document the performance of a wind tunnel model incorporating the Goldschmied propulsor concept and complete an examination of its aerodynamic performance. The investigation took place at California Polytechnic …

Water And Energy Conservation Grow System: Aquaponics And Aeroponics With A Cycle Timer, Roger Hancock

Electrical Engineering

What some experts call the “blue gold”; water is a major issue in this world. There is only so much water and the reliability and cleanliness of water is what many developing countries are dealing with today. Countries around the world are facing problems with reliable water to grow enough food for their villages and homes. Is there is a way to minimize water consumption while optimizing growth in plants for food? One solution can be seen through both Aeroponics and Aquaponics. This project explores the potential of providing larger quantities of food to areas where water may be in …

3.5 To 30 Mhz Automatic Antenna Impedance Matching System, William Blodgett

Electrical Engineering

Two-way communications using 3 to 30 MHz, high-frequency (HF) radio, also known as shortwave radio, provides worldwide coverage with no infrastructure required between stations. Amateur or “Ham” radio operators apply this advantage to long distance communications and to provide disaster relief communications. Optimum frequencies for long distance propagation are time-of-day variant necessitating an operating frequency range of 3 to 30 MHz. HF half wave dipole antenna length varies from 15 to 150 ft over this range. Fixed-length antenna impedance varies with frequency due to physical dimension dependent capacitance and inductance. Maximum transmitter to antenna power transfer occurs when the transmission …

Improved Microalgal Biomass Harvesting Using Optimized Environmental Conditions And Bacterial Bioflocculants, Derek C. Manheim

Master's Theses

ABSTRACT

IMPROVED MICROALGAL BIOMASS HARVESTING USING OPTIMIZED ENVIRONMENTAL CONDITIONS AND BACTERIAL BIOFLOCCULANTS

DEREK CONTE MANHEIM

The cost and energy balance of microalgae biofuel production is sensitive to the algae harvesting method, among many other factors. Bioflocculation and settling of suspended microalgae cultures is a harvesting method with potentially low cost and energy input. However, bioflocculation (the spontaneous flocculation of algal cells without chemical addition) has not been a reliable process with cultures grown in ponds. To provide insights to help improve algae settling, factors affecting the settling of algae were investigated in the laboratory using pure cultures of two common …

Engineering Performance Of Polymer Amended Soils, Gary E. Welling

Master's Theses

A laboratory test program was undertaken to evaluate a series of engineering properties over a range of soil types; amendment types and addition rates; and moisture contents to enhance understanding of the engineering significance of polymer amendment. Four soils were manufactured and tested with varying ranges of fines and plasticity. A proprietary elastic copolymer was tested at addition rates of 0.5% to 2.5% (dry weight basis). Cement was tested at addition rates of 1% to 4%. Lime was tested at an 8% addition rate. Water addition rates ranged from 4% dry of optimum to 4% wet of optimum. Engineering properties …

Scale Model Shake Table Testing Of Shallow Embedded Foundations In Soft Clay, Steven Kuo

Master's Theses

This research involves shake table testing of 1g scale models that mimic the coupled seismic response of a structure on a shallow mat foundation and foundation soil (known as soil-foundation-structural-interaction or SFSI). In previous research, SFSI effects have been quantified through analytical models, numerical analyses, and limited field data. This research works towards increasing the amount of empirical data through scale model shake table testing. A suite of earthquake time histories is considered in evaluating a nominal 10^th scale soil-structure model using a flexible wall barrel on a 1-D shake table. San Francisco Young Bay Mud (YBM) is used …

Touchspice Vs. Reactive-Spice: A Human-Computer Interaction Perspective, Joshua Martin O'Hara

Master's Theses

Traditional SPICE simulation tools and applications of circuit theory lack real-time interaction and feedback. The goal of this thesis was to create an interactive physical environment to allow the manipulation and simulation of discrete electrical components in near-real-time while optimizing and streamlining the human-computer interaction (HCI) elements to make the user experience as positive and transparent as possible. This type of HCI and near-real-time simulation feedback would allow for the instant realization of how the parameters of each discrete component or hardware module affect the overall simulation and response of the circuit.

The scope of this thesis is to research, …

Structural Damage Detection Using Artificial Neural Networks And Wavelet Transform, Arthur Shi, Xiao-Hua Yu

Electrical Engineering

With the ever-increasing demand for the safety and functionality of civil infrastructures, structure health monitoring (SHM) has now become more and more important.

Recent developments in computational intelligence and digital signal processing offer great potentials to develop a more efficient, reliable, and robust structure damage identification system. In this paper, the application of artificial neural networks and wavelet analysis is investigated to develop an intelligent and adaptive structural damage detection system. The proposed approach is tested on an IASC (International Association for Structural Control)-ASCE (American Society of Civil Engineers) SHM benchmark problem. Satisfactory computer simulation results are obtained.

Implementation Of Magnetic Meters For Irrigation Volumetric Measurement, Stuart Styles, Lynn Groundwater

BioResource and Agricultural Engineering

The irrigation industry is experiencing a growth in the use of magnetic meters for measuring the flow rate and volume in irrigation pipelines. Historically, propeller meters have been the device selected by users. New legislation in California (SB7x7) will require measurement devices at key locations for irrigation water delivery. Some users are very interested in the magnetic meter for making the measurement at the turnout or farm gate. The key feature of the new meter is the ability for the device to work in less than ideal flow conditions. Electromagnetic meters have been tested by the Irrigation Training and Research …

Brain Recorder, Anthony M. Garcia

Computer Engineering

Electroencephalography (EEG) is the recording of electrical activity along the scalp. Our mind regulates its activities by means of electric waves which are registered in the brain, emitting tiny electrochemical impulses of varied frequencies, which can be registered by an electroencephalogram. These “brainwave” frequencies are split into different bands. There is ongoing research that attempts to correlate the frequencies in the different bands to different emotional states and levels of concentration. With the increase in availability of commercial EEG devices, such studies can be sped up by making the collection of data easier, faster, and mobile. Creating a mobile application …