Engineering Commons^™

Solar Energy Collection Analysis Tool For Conceptual Aircraft Design, Grant M. Glazebrook, Robert A. Mcdonald

Aerospace Engineering

As battery energy storage and solar cell technology improve, solar aircraft are increasingly being considered for high altitude long endurance missions. Although solar vehicles may theoretically remain on station indefinitely using the sun as a power source, their design and feasibility is sensitive to mission planning details as specific as the time history of the vehicle’s deck orientation relative to the sun; the energy available for capture by the on-board solar array is governed by the solar incidence angle, and at certain orientations, the vehicle may cast shadows on itself and further reduce its energy capture capabilities. To quantify these …

Pressure Regulating Valve Pilot Characteristics - 2-Way Vs. 3-Way Pilots, Charles M. Burt, Kyle Feist

BioResource and Agricultural Engineering

Pressure regulation valves, with 3” – 6” diameters, are commonly found at the entrance to agricultural irrigation blocks and manifolds. These valves are typical of a “hydraulic” design, in which a chamber above a flexible disc/diaphragm is filled or emptied. As the chamber is filled or emptied, the irrigation water passes through a smaller or larger orifice, and the pressure downstream of the valve is lowered, increased, or maintained at a constant target pressure. The flow in/out of the chamber is controlled by a small “pilot valve”. The characteristics of these pilot valves are discussed here, in general terms. Of …

Investigation Of Astm E 238 Bearing Pin Properties For Various Aerospace Alloys, Trevor J. Lee

Master's Theses

Aircraft are often designed with numbers determined by testing in a lab, rather than by repeatedly building prototypes. These lab tests conform to testing specifications so that the numbers can be compared between manufacturers, suppliers, and lab technicians. One such specification is ASTM specification E238 – 84(08), and it is used to determine important properties of a bearing pin joint like hinges, bolt holes, and rivet joints. The properties determined from this fastener-through-plate method are bearing strength, bearing yield strength, and bearing stiffness.

Adhering to the methods outlined in ASTM E238, a study was performed, looking at the effects that …

Methanol Fuel Safety - A Practical Guide, Art Maccarley

Electrical Engineering

This guide was written initially for the students at Cal Poly engaged in the conversion of IC engines to methanol fuel, especially my students working on methanol projects in my course “Automotive Technologies for a Sustainable Future”. It may be of interest to anyone considering the conversion or operation of an engine on methanol, or to those that handle methanol for other purposes. One of many Materials Safety Data Sheets (MSDS) for methanol that can be found online is: http://www.midi-inc.com/pdf/MSDS_Methanol.pdf.

Rainwater To Flush Toilets On A Volcano, Robert A. Buchan

STAR Program Research Presentations

Objective: Investigate the feasibility of a rainwater collection system to provide for a sustainable source of non-potable or potable water at a potentially isolated solar observatory site (likely Mauna Loa Observatory in Hawaii).

Introduction: The National Center for Atmospheric Research/High Altitude Observatory (NCAR/HAO) proposes to build a solar observatory comprising a trio of instruments for studying solar coronal magnetism.

Methods: Each square foot of collection surface will experience approximately 0.62 gallons of runoff from 1 inch of rainfall (12 in x 12 in x 1 in = 0.62 gallons). Some water will be lost to evaporation, splashing, overflows, and other …

Pipeline And Canal Downstream Control System For Recirculation - Patterson Id Case Study, John Sweigard, Charles M. Burt, Peter Rietkerk

BioResource and Agricultural Engineering

Patterson ID in Central California has five long, along-the-contour lateral canals that flow northward from a main canal. The main canal operates on downstream control, providing excellent flexibility to heads of the laterals. The lateral canals operate with manual upstream control and have little storage. The classic tail-ender problem existed; spill from the tail end was necessary to avoid under-supplying tail-end customers.

To eliminate the spill and to provide better flexibility, a system was designed and constructed to tie the ends of the five laterals together with pipes and pumps, with one central regulating reservoir. The automatic control system allows …

Geothermal Injection Well Monitoring, Timothy Rempher

Electrical Engineering

People depend on electricity all over the world. They depend on it for anything from drying their hair to global communications to heating up food. Many methods of power generation exist, each using a different fuel such as nuclear power, natural gas, coal, wind or the sun. This project focuses on a power plant which uses the naturally hot water in the ground to generate electricity. This process of generating power is called “Geothermal.” This project consists of two parts. The first and major part is the design logic of a PLC program that monitors the flow rate of an …

The Effect Of Sensor Mass, Sensor Location, And Delamination Location Of Different Composite Structures Under Dynamic Loading, Albert Darien Liu

Master's Theses

This study investigated the effect of sensor mass, sensor location, and delamination location of different composite structures under dynamic loading. The study pertains to research of the use of accelerometers and dynamic response as a cost-effective and reliable method of structural health monitoring in composite structures. The composite structures in this research included carbon fiber plates, carbon fiber-foam sandwich panels, and carbon-fiber honeycomb sandwich panels. The composite structures were manufactured with the use of a Tetrahedron MTP-8 heat press. All work was conducted in the Cal Poly Aerospace Structures/Composites Laboratory. Initial delaminations were placed at several locations along the specimen, …

Slowing The Onset Of Hypoxia Increases Colony Forming Efficiency Of Connective Tissue Progenitor Cells In Vitro, Christopher M. Heylman, Tonya N. Caralla, Cynthia A. Boehm, Thomas E. Patterson, George F. Muschler

Biomedical Engineering

Background: Survival and colony formation by transplanted tissue derived connective tissue progenitor cells (CTPs) are thought to be important factors in the success of clinical tissue engineering strategies for bone regeneration. Transplantation of cells into defects larger than a few millimeters expose cells to a profoundly hypoxic environment. This study tested the hypothesis that delaying the onset of hypoxia will improve the survival and performance of CTPs in vitro.

Methods: To mimic declines seen in an avascular in vivo bone defect, colony forming efficiency by marrow derived nucleated cells was assessed under osteogenic conditions. Variation in the rate of …

Cal Poly Nano Hydro, Brandon N. Fujio, Alex J. Sobel, Andrew F. Del Prete

Mechanical Engineering

This projects goal was to design, construct, and test a machine capable of generating a usable amount of energy from naturally flowing water. The device conceived for this purpose is a portable raft with a turbine mounted to the underside. The turbine is mated directly to a low angular velocity generator which outputs to a power electronics system on shore. Using a Gorlov Helical turbine, this proof-of-concept is designed to output ~50 Watts of electricity to charge a battery for later use. Possible applications for this device include camping in remote locations, supplemental power generation for a home, or for …

Dc-Dc Converter Input Protection System For The Energy Harvesting From Exercise Machines (Ehfem) Project, Ryan Turner, Zack Weiler

Electrical Engineering

The ongoing Energy Harvesting from Exercise Machines (EHFEM) project at Cal Poly San Luis Obispo seeks to provide renewable energy without the high cost of implementation by harvesting DC power generated on machines used for physical exercise. The EHFEM project consists of numerous subprojects that involve converting different types of exercise machines for power generation. This project specifically works by scaling the output voltage from an elliptical machine using a DC-DC converter and sending it through an Enphase Micro-inverter to feed AC power back to the power grid and minimize energy spending. As a subset of the much larger project, …

Optimizing Electrode Design For Microbial Fuel Cells Used For Wastewater Treatment, Lindsay Nichols, John A. Hogan

STAR Program Research Presentations

Microbial fuel cells (MFC) utilize bacteria to generate an electrical current that can be used in the decomposition of sludge and human urine. In a MFC there is an anode (for oxidation of organic compounds), cathode (reduction of oxygen or carbon dioxide), and a proton exchange membrane (PEM, allows protons to migrate); reduction-oxidation reactions between the anode and cathode produce a measurable current. Bacteria that are found in sludge can be used to produce electrons in a voltaic cell, but optimizing conditions for harnessing the energy is crucial to making a MFC efficient. Research has shown that the ratios of …

A Tunable Electromagnetic Band-Gap Microstrip Filter, Greg A. Lancaster

Master's Theses

In high frequency design, harmonic suppression is a persistent struggle. Non-linear devices such as switches and amplifiers produce unwanted harmonics which may interfere with other frequency bands. Filtering is a widely accepted solution, however there are various shortcomings involved. Suppressing multiple harmonics, if desired, with traditional lumped element and distributed component band-stop filters requires using multiple filters. These topologies are not easily made tunable either. A new filter topology is investigated called Electromagnetic Band-Gap (EBG) structures.

EBG structures have recently gained the interest of microwave designers due to their periodic nature which prohibits the propagation of certain frequency bands. EBG …

Solar Energy Collection Analysis Tool For Conceptual Aircraft Design, Grant Glazebrook

Aerospace Engineering

As battery energy storage and solar cell technology improve, solar aircraft are increasingly being considered for High Altitude Long Endurance missions. Although solar vehicles may theoretically remain on-station indefinitely using the sun as a power source, their design and feasibility is sensitive to mission planning details as specific as the time history of the vehicle’s deck orientation relative to the sun; the energy available for capture by the on-board solar array is governed by the solar incidence angle, and at certain orientations, the vehicle may cast shadows on itself and further reduce its energy capture capabilities. To quantify these losses, …

The Architecture Selection, Design, And Discharge Modeling Of A Passive Compensation, Iron-Core, Two-Phase, Permanent Magnet Compulsator To Power A Small Railgun Platform, Collin Macgregor

Aerospace Engineering

The goal of this project was to design and build a compensated pulsed alternator, or compulsator, to power the Cal Poly Electromagnetic Railgun Mark 1.1. This project examines the feasibility of implementing mechanical pulsed power supplies for repeatable use with a railgun load for orbital debris hypervelocity testing. The final system architecture chosen was a passively compensated, iron-core, 2-phase, permanent magnet compulsator. The Cal Poly Compulsator will be capable of storing 45 kJ of mechanical energy with a peak operating speed of 5,000 rpm at 190 V. Theoretical calculations resulted in the following predicted electrical performance values: a peak output …

Quantum Dot Deposition Into Pdms And Application Onto A Solar Cell, Christopher Marcus Botros, Richard N. Savage

Master's Theses

Research to increase the efficiency of conventional solar cells is constantly underway. The goal of this work is to increase the efficiency of conventional solar cells by incorporating quantum dot (QD) nanoparticles in the absorption mechanism. The strategy is to have the QDs absorb UV and fluoresce photons in the visible region that are more readily absorbed by the cells. The outcome is that the cells have more visible photons to absorb and have increased power output. The QDs, having a CdSe core and a ZnS shell, were applied to the solar cells as follows. First, the QDs were synthesized …

Investigation Of Out-Of-Plane Properties Of Interlocking Compressed Earth Block Walls, Nicholas Anthony Herskedal

Master's Theses

Interlocking compressed earth blocks (ICEBs) are cement stabilized soil blocks that allow for dry stacked construction. The incomplete understanding of the inelastic performance of ICEB building systems limits widespread acceptance of this structural system in earthquake prone areas. This thesis presents results from an experimental program designed to explore the behavior of ICEB walls, built according to current design practice in Indonesia and Thailand, and subjected to out-of-plane loading. A total of five reinforced and grouted ICEB walls were constructed and tested.

Results from experimentation show the current masonry design code, ACI 530, adequately predicts the yield strength of these …

Strider: Manufacturing Processes, Michael Warren-Angelucci

Industrial and Manufacturing Engineering

The goal of the Strider Project is to create a mobility device that can support a person with weakened leg strength and enable them to be supported and maintain a standing position. A prototype of the Strider was created by three Mechanical Engineering students as their senior project. The topic of this senior project was to analyze and create a manufacturing process for the manufacture of the Strider that will be ergonomic and cost effective.

There were many things that needed to be accomplished in order to create the manufacturing process. The first step was to verify that the prototype …

Using Player Profiling To Enhance Dynamic Difficulty Adjustment In Video Games, Aaron Burke

Computer Engineering

Video games have certainly come a long way since the days of pong. From humble beginnings of the first arcade machines they have bloomed into a multi-billion dollar industry and a global force to be reckoned with. Just like with movies there are enough genres out there to fit any demographic of gamer, and that’s not even just the game’s content but also the gameplay.

Unlike other types of media though, games are meant to be interacted with and played, which brings up new issues with accessibility and keeping things interesting for different levels of skill. Dynamic game difficulty adjustment …

Micro-Grid Wind Energy System, Aaron Steinkraus, Brian Huntziker, Cesar Hurtado

Mechanical Engineering

With the completion of a 3.5kW wind turbine located on Esculea Ranch, the power generated from the turbine was dissipated through electric resistance heaters. ABC Wind was given the task to design, build, and implement a system what will efficiently use the turbine’s harnessed power. After interviewing with the Beef Operations Manager of Escuela Ranch, it was decided to use the turbine’s power to supply supplementary water to anywhere on the ranch where and when needed by grazing cattle. The purpose of this project was to research, design, build and implement a system that would harness the generated power and …

Early Forest Fire Detection Using Texture, Blob Threshold, And Motion Analysis Of Principal Components, Georges Fouad Moussa

Master's Theses

Forest fires constantly threaten ecological systems, infrastructure and human lives. The purpose behind this study is minimizing the devastating damage caused by forest fires. Since it is impossible to completely avoid their occurrences, it is essential to accomplish a fast and appropriate intervention to minimize their destructive consequences. The most traditional method for detecting forest fires is human based surveillance through lookout towers. However, this study presents a more modern technique. It utilizes land-based real-time multispectral video processing to identify and determine the possibility of fire occurring within the camera’s field of view. The temporal, spectral, and spatial signatures of …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Laboratory Investigation Of The Effects Of Temperature And Moisture On Interface Shear Strength Of Textured Geomembrane And Geosynthetic Clay Liner, Taki Stavros Chrysovergis

Master's Theses

A laboratory investigation was conducted to determine the effects of temperature and moisture on the shear strength of textured geomembrane (T-GM) and geosynthetic clay liner (GCL) interface. Several landfill slope failures involving geosynthetics have occurred within the past three decades. Interface shear strength of T-GM/GCL is well documented for testing conducted at laboratory temperatures and at moisture contents associated with GCLs in submerged conditions. However, in-service conditions for landfill liner systems include a wide range of temperatures (extending from below 0 °C to above 40 °C) and a wide range of moisture conditions. Large-scale interface direct shear tests were performed …

The Application Of Systems Engineering Principles To Model Lithium Ion Battery Voltage, George Gibbs

Master's Theses

The objective of this project is to present a Lithium Ion battery voltage model derived using systems engineering principles. This paper will describe the details of the model and the implementation of the model in practical use in a power system. Additionally, the model code is described and results of the model output are compared to battery cell test data. Finally, recommendations for increased model fidelity and capability are summarized.

The modeling theory has been previously documented in the literature but detailed implementation and application of the modeling theory is shown. The detailed battery cell test voltage profiles are proprietary; …

Measuring Impedance Of Tissues Using A Microfabricated Microelectrode Array, Ashwini Bhat

Master's Theses

MEASURING IMPEDANCE OF TISSUES USING A MICROFABRICATED MICROELECTRODE ARRAY By Ashwini Bhat

This thesis looks at the possibility of using impedance spectroscopy for differentiating tissue, using a microelectrode array (MEA). The thesis first discusses the background and the motivation for this thesis. It covers the certain basic concepts of the human skin starting from the top epidermis layer all the way to the deep dermis layers of the skin. Then it discusses different types of skin cancer and how they occur, in humans. It also discusses various microfabrication techniques such as oxidation, wet etching, sputtering and photolithography for the creation …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Single-Phase High Efficiency Motor Testing, Marc Henry Perez

Electrical Engineering

A three-phase induction motor has higher efficiency than the single-phase motor counterpart. It is possible to run a three-phase motor with a single-phase source to develop a single-phase high efficiency system. The single-phase high efficiency motor, or SHE-motor, uses capacitor banks to operate at a balanced three phase induction motor using a single phase source. Unfortunately, this design has been limited, as it can only be balanced for one load configuration at a time. This provides the system to have maximum system performance. Due to this limitation in operations, it has proven to be non-ideal in commercial applications. It is …

Handitrike - Recumbent Tricycle, Sean Higginson, Kevin Howie, Vinay Patel

Mechanical Engineering

This report covers the design and construction of the recumbent racing tricycle for Mr. Robert T. Kelly, a disabled veteran. Unfortunately Rob’s right leg is five inches shorter than his left one and therefore is unable to properly operate standard cranks. Our team HandiTrike is composed of Sean Higginson, Kevin Howie, and Vinay Patel and our project requires us to come up with a design that is feasible to complete within the given three quarters, as well as allow Rob to gain full use of his tricycle. Currently Rob ‘s trike uses the standard crank set up found on most …

A.C.E. Lift: Assisted Cab Entry Lift System For Heavy Equipment Vehicles, Michael Berry, Eric Imazumi

Mechanical Engineering

The A.C.E. is a lift system to allow users with above-knee prosthetics to access the cab of heavy machinery. It is being designed as a senior project for California Polytechnic State University’s mechanical engineering curriculum with support from Quality of Life Plus (QL+) and sponsored by Jon Monett. In accordance with QL+’s mission of helping wounded veterans integrate into the workforce, the A.C.E. lift will allow disabled individuals to obtain jobs in the construction, agriculture, and waste management industries.

As a continuation of a previous senior project that focused on a Caterpillar excavator, the new design will be applicable to …

Formula Sae Turbocharger Engine Development, Eric Griess, Kevin Mccutcheon, Matthew Roberts, William Chan

Mechanical Engineering

This project, Formula SAE Turbocharger System Development, was sponsored by the Cal Poly, San Luis Obispo Formula SAE team. The team proposed this project in order to have a powerful yet lightweight engine so they can be extremely competitive at their competition. The baseline output of the single cylinder 450cc engine (2006 Yamaha WR450F) was 46 horsepower and 27 ft-lb of torque. The goal of this project was to increase the output of that engine to 60 horsepower and 35 ft-lb through the use of a turbocharger.