Microgrid Power Quality Analysis, Nikolai Kempcatala, Daniel Pleau, Scott Clemons

Electrical Engineering

The microgrid power quality analysis senior project addresses power quality assessment. Our senior project uses the PowerSight 3000 power measurement tool to record and analyze various electrical measurements including voltage, current, power, power factor, harmonics and AC frequency.

Our project will analyze power quality issues that result from switching from the utility grid to a smart grid run on primarily photovoltaic distributed generation. In the event of a utility failure, the smart grid can serve as an isolated grid for the system, this is called islanded mode. Our project assesses the reliability of operation in islanded mode. Our analysis should …

Design And Evaluation Of An Irrigation System For Meyer Lemons, Anthony Atchley

BioResource and Agricultural Engineering

This senior project discusses the design and implementation procedures for an irrigation system for Meyer lemons. The irrigation system is designed from an economical standpoint incorporating limitations set by the ranch manager such as the use of existing pipe lines and emitter selection preference. Within this project there are the steps taken to ensure a healthy crop utilizing the data and advice collected from other fields and their managers in the same area.

The entire field is run as a single set with two manifolds to supply the Western and Eastern ends of the field. A total of 555 trees …

Dc House Distribution Panel, Khanh Ho

Electrical Engineering

This paper details the process in designing the distribution panel, or circuit breaker box for a DC house. The main purpose of the project is to design a distribution panel that will provide electrical power to the DC house while also providing an electrical system protection through the use of circuit breakers, or fuses. An actual hardware design for the distribution panel was built and tested. The results demonstrate the functionality of the breaker box to supply power to the DC House ensuring safe operation of the DC House.

Ad-Hoc Regional Coverage Constellations Of Cubesats Using Secondary Launches, Guy G. Zohar

Master's Theses

As development of CubeSat based architectures increase, methods of deploying constellations of CubeSats are required to increase functionality of future systems. Given their low cost and quickly increasing launch opportunities, large numbers of CubeSats can easily be developed and deployed in orbit. However, as secondary payloads, CubeSats are severely limited in their options for deployment into appropriate constellation geometries.

This thesis examines the current methods for deploying cubes and proposes new and efficient geometries using secondary launch opportunities. Due to the current deployment hardware architecture, only the use of different launch opportunities, deployment direction, and deployment timing for individual cubes …

A Microfluidic Pretreatment Isoelectric Focusing Dc-Field Assisted H-Filter For The Separation Of Charged Particles, Cameron Sean Carroll

Biomedical Engineering

Microfluidic devices are small portable diagnostic chips that allow for analysis of a biologic sample at relatively low cost. This makes them ideal for settings where a hospital is unavailable. The microfluidic pretreatment isoelectric focusing DC-field assisted H-filter is a device that allows for the separation of differently charged particles in a biologic sample. It does this by employing the concepts of diffusion, electrophoresis, and isoelectric focusing. This is perfect for isolation of a desired analyte or separation of waste from a sample in order to achieve better diagnostic results. The device was first modeled mathematically and visually using Comsol. …

Investigating The Reproducibility Of The Current Bvm Protocol, Corey Gross

Biomedical Engineering

Coronary Artery Disease (CAD) is responsible for 1 death every minute in the US. Angioplasty with the implantation of stents is a common treatment method for CAD. Although there is a variety of stents currently on the market, there is still a need to develop new types for different pathologic conditions. Preliminary assessment of the physiological response to new stents is needed as they are being developed. The FDA approval process implemented today is a long, tedious path with a range of testing methods that include static in vitro testing and high-cost animal testing. Tissue engineered blood vessels have been …

Design And Optimization Of A Keycard Encoding Machine, Elliott Oberg

Biomedical Engineering

Security on college campuses is a good thing, especially when it comes to your dorm room or apartment building. But due to high initial cost, the Housing and Business Department at Cal Poly, San Luis Obispo, has opted for a proprietary door lock system which requires encoding new keycards manually for every resident, every year. The goal of this project is to offset this labor cost and drain on resources by automating the keycard encoding process. This project will address the design specifications and economic advantages of automation while also exploring and comparing alternative solutions.

Mickey's Memory Game: A Children's Memory Game Designed For Sifteo Cubes, Anjelica Concepcion

Computer Engineering

Mickey’s Memory Game is a children’s memory game developed on the Sifteo platform. Sifteo cubes are small, interactive devices, which can display colored images and sense neighboring cubes or detect user actions, such as clicking, shaking, or tilting the cubes. Although many classic video games or mobile games can be recreated on the Sifteo cubes, the goal of this project was to utilize capabilities that are unique to the Sifteo gaming platform, while also creating a useful game for child development.

Women's High Heel Discomfort Analysis And Prototype Solution, Kevin Blakley, Annamarie Kepple

Industrial and Manufacturing Engineering

ABSTRACT

WOMEN’S HIGH HEEL DISCOMFORT ANALYSIS AND SOLUTION

Kevin Blakley and Annamarie Kepple

Women love high heeled shoes, but this love comes at the cost of comfort. Wearing high heels causes a lot of pain and, in the long term, health complications. This project tries to overcome the problem by ultimately making high heels more comfortable. In order to do this, one must first understand the reasons that high heels are uncomfortable, such as arch angle, heel height, and the changes in walking motion. Once there is a true understanding of the factors that contribute to high heel discomfort, the …

Axisymmetric Air Augmented Methanol/Gox Rocket Mixing Duct Experimental Thrust Study, Kyle Jacob Johnson

Master's Theses

A hot-flow axisymmetric Air Augmented Rocket (AAR) test apparatus was constructed to test various mixing duct configurations at static conditions. Primary flow for the AAR was provided through a liquid methanol-gaseous oxygen bipropellant rocket. Experimental thrust measurements were recorded and propellant mass flow rates and chamber conditions were calculated using an iterative solver dependant on recorded propellant line stagnation pressures. Primary rocket flow produced thrust ranging from 14 to 17.9lbf. Primary mass flow rate through testing ranged from 0.071 to 0.085lbm/s with calculated chamber pressures between 298-362psia. Calculated primary flow velocity ranged from 6,600ft/s to 8,000ft/s depending on propellant pressure …

Effects Of Ovariectomy And Anatomical Location On Osteonal Encroachment In Adult Cortical Ovine Bone, Paige Brell Ryan

Master's Theses

The purpose of this study is to further quantify adult ovine ovariectomized bone for new remodeling characteristics to obtain a better understanding of how remodeling is occurring and the effectiveness of this animal model for the study of postmenopausal osteoporosis. Postmenopausal osteoporosis is a major health concern and animal models to test new treatment options are needed. The ovine model is a good option because the ewes undergo Haversian remodeling, are a large sized animal, and have a similar hormone profile to humans. Ewes, however, do not undergo a natural menopause, so an ovariectomy surgery was conducted in the sheep …

Modeling Flood Reduction Scenarios For A Small Coastal Community, Evan J. Perez

Master's Theses

The Arroyo Grande Creek Watershed, an approximately 170 mi² watershed located on the central coast of California, drains to the Pacific Ocean via the Arroyo Grande Creek that passes through several coastal cities including the community of Oceano. At the mouth of the Creek is the Arroyo Grande Lagoon, which is connected to another lagoon known as the Oceano Lagoon, by a tidal flap-gate whose hydraulics is a function of water levels in the two lagoons. Historically the Oceano Lagoon has played a part in floods that have occurred in the community of Oceano. The most recent flooding occurred …

System Identification Of A Bridge-Type Building Structure, Pablo D. Ramos Jr.

Master's Theses

The Bridge House is a steel building structure located in Poly Canyon, a rural area inside the campus of California Polytechnic State University, San Luis Obispo. The Bridge House is a one story steel structure supported on 4 concrete piers with a lateral force resisting system (LFRS) composed of ordinary moment frames in the N-S direction and braced frames in the E-W direction and vertically supported by a pair of trusses. The dynamic response of the Bridge House was investigated by means of system identification through ambient and forced vibration testing. Interesting findings such as diaphragm flexibility, foundation flexibility and …

Design And Performance Of Circulation Control Geometries, Rory Martin Golden

Master's Theses

With the pursuit of more advanced and environmentally-friendly technologies of today’s society, the airline industry has been pushed further to investigate solutions that will reduce airport noise and congestion, cut down on emissions, and improve the overall performance of aircraft. These items directly influence airport size (runway length), flight patterns in the community surrounding the airport, cruise speed, and many other aircraft design considerations which are setting the requirements for next generation aircraft. Leading the research in this movement is NASA, which has set specific goals for the next generation regional airliners and has categorized the designs that meet the …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Hydrologic Modeling Of The San Joaquin Valley Watershed For Purposes Of Nitrate Analysis, Stephen Carl Clayton

Master's Theses

The San Joaquin Valley is regarded as one of the most productive agricultural regions in the world. This extensive agriculture has, however, caused extensive pollution of both ground water and surface water. This thesis develops a hydrologic model of the surface and ground waters of the San Joaquin Valley. Such modeling is useful in the development and implementation of water quality regulations such as Total Maximum Daily Loads (TMDLs). A properly validated watershed simulation model can supplement data collection and can account for watershed characteristics including topography, soils, climate, land cover, anthropogenic activities, as well as simulate watershed responses including …

Rfid Technology Selection And Economic Justification For Healthcare Asset Tracking, Tyler Robert Peabody, Tali Freed

Master's Theses

Although Radio Frequency Identification (RFID) and Real-Time Location System (RTLS) technologies for inventory tracking have been growing in popularity, the healthcare industry has been reluctant to adopt these technologies. One of the primary reasons for this lack of enthusiasm has been the risk associated with electromagnetic interference between RFID/RTLS systems and medical equipment functionality. The other reason has been the substantial cost and complexity of implementing RFID/RTLS in healthcare organizations. In this study, we show that there are several ways to safely install RFID/RTLS systems to improve the inventory management processes of hospitals and clinics. We then analyze the inventory …

Cloth Filter For Disaster Relief Water Treatment, Shasta Le'ja Billings

Master's Theses

Relief organizations and governments strive to provide safe drinking water to natural disaster survivors as quickly as possible. However, drinking water is typically provided either as bottled water or via mobile water treatment equipment, both of which can be difficult or expensive to transport rapidly into disaster zones. An alternative is the waterbag point-of-use treatment device developed at Cal Poly that allows survivors to produce safe drinking water from contaminated local sources. The waterbag is a 10-L bladder designed for use with Procter & Gamble Purifier of Water (PŪR^®) sachets, which contain coagulant and chlorine compounds. Following treatment …

Bacterial Growth On Metal And Non-Metal Surfaces In A Static Bioreactor, Rolan Yuk Loong Liong

Master's Theses

Research was conducted to observe bacterial growth on the surface of metals in a static bioreactor. Metal and non-metal samples were subjected to bacterial exposure (1 day and 9 days). The metal samples were surface treated prior to bacterial exposure. The microstructures of the surface treated samples were analyzed by optical microscopy. After exposure, the microstructures of the samples were analyzed by scanning electron microscopy (SEM). The analysis suggested that microbial attachment on the surface was related to the underlying microstructure of steel. The preferential attachment of microbes could potentially be influenced by cathodic and anodic regions created by the …

Kase, The Laptop Cooling Case, Jana Morrison, Tyler Ries

Biomedical Engineering

This report describes the final design and analysis of a laptop cooling case as a marketable product for a group of entrepreneurial marketing student based out of California Polytechnic State University San Luis Obispo. Background market research and empirical measurements were taken in order to confirm that this would be a marketable product worth designing. Then previous solutions were researched in order to identity weaknesses and strengths. After rigorous research, it was determined that a passive cooling system, in which channels directed airflow to the computer fan would be the best system in terms of functionality, performance, and cost. A …

Biomedical Advancements In Injury Recovery, Performance Enhancement, And Mechanical Assistance Applied To Athletics, Matthew Russell

Biomedical Engineering

Athletics is constantly changing, and athletes are continually getting bigger, faster, and stronger. At the same time, biomedical technology and innovation is rapidly developing. New methods of injury recovery, genetic enhancement, and prosthetic assistance are being assimilated into the athletic world. The up and coming athlete needs to be aware of all of the usable information around them. This project is an accumulation of some of the cutting edge advancements in those fields. Platelet Rich Plasma Injections, Frequency Specific Microcurrent Treatment, and Silk Polymer Anterior Cruciate Ligament Replacement are innovative new ways to treat common sports injuries. Performance enhancement has …

Polyparking, Christopher Blackmer, Michael Suttie

Biomedical Engineering

The purpose of this senior project is to analyze the various options for the implementation of a parking lot information system on the California Polytechnic State University, San Luis Obispo campus. This system would involve three main components: physical counting hardware, a database and analysis organization system, and a user interface for disseminating the gathered information. The project investigates and provides commentary on various available and commonplace systems, and the benefits and drawbacks of these systems. During the course of the project, a flexible database and user-interface was developed in Microsoft Access, which will allow counter output to be gathered …

Deterioration Of Metal–Organic Framework Crystal Structure During Fabrication Of Poly(L-Lactic Acid) Mixed-Matrix Membranes, Ajay Kathuria, Mohamad G. Abiad, Rafael Auras

Industrial Technology and Packaging

Poly(l-lactic acid) (PLLA) and metal–organic framework (MOF) mixed-matrix membranes were prepared by melt extrusion of PLLA with 5% (w/w) of either activated or water-saturated Cu₃(BTC)₂ (Cu₃(C₉H₃O₆)₂(H₂O)₃·xH₂O, HKUST-1). The morphology and the stability of injection-molded samples were evaluated using thermogravimetric analysis, differential scanning calorimetry, gel permeation chromatography, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The presence of activated and saturated MOF crystals increased the cold crystallization onset temperature as compared to neat PLLA. This can be attributed to the …

Smore Revision: Ignition And User Interface, Arash Mehrparvar

Aerospace Engineering

The Static Methanol Oxygen Rocket Engine (SMORE) has undergone several revisions since its inception. This latest revision aimed to increase startup reliability and user safety in the operation of the rocket. The implementation of maintenance procedures, safeguards in the ignition system, as well as construction of a new control box and redesign of the igniter itself have accomplished these goals while keeping costs down and without modifying the current rocket setup. Startup reliability has increased drastically, so long as all other rocket setup procedures are followed properly. 250 subsequent firings of the rocket have proven an igniter reliability of more …

A Biomechanical Comparison Of Three Spondylolysis Repair Techniques In A Calf Spine Model, R. Roberto, B. Dezfuli, C. Deuel, S. Curtiss, S. Hazelwood

Biomedical Engineering

Summary of background data: Previous work has demonstrated the efficacy of lumbar pedicle screw hook rod (PSHR) techniques and the Buck screw in the stabilization of spondylolysis. The mechanical behavior of lower profile cervical implants used to create PSHR, hybrid cable plate constructs, and titanium miniplating has not previously been described.

Methods: Calf lumbar spines (L2-L6) were utilized for testing (n = 27). Intervertebral rotation was measured in the intact spines across the L4-5 segment before and after creation of bilateral pars interarticularis defects. Defects were then stabilized with one of three repair techniques, PSHR, miniplate, or …

Electric Motor Modeling For Conceptual Aircraft Design, Robert A. Mcdonald

Aerospace Engineering

Electric motors have achieved very high efficiency and reliability; and in some cases, very high specific power. As the energy storage capabilities of batteries and fuel cells advance, these technologies are increasingly being considered for aircraft primary propulsion. In order to design electric aircraft, aircraft designers must be able to understand and model the performance characteristics of electric motors. Most electric machine modeling techniques either ignore potentially important phenomena or require an extreme level of detail undesirable for conceptual aircraft design. In this paper, a compromise approach is proposed which can capture the salient details of motor performance without requiring …

Enabling Rapid Conceptual Design Using Geometry-Based Multi-Fidelity Models In Vsp, Joel B. Belben, Robert A. Mcdonald

Aerospace Engineering

Four types of reduced fidelity or degenerate geometric representations have been defined and implemented in VSP for the purpose bridging the gap between conceptual design and analysis. They are Degenerate Surface, Degenerate Plate, Degenerate Stick, and Degenerate Point, corresponding to three-, two-, one-, and zero-dimensional representations of underlying geometry, respectively. The information contained in these representations was targeted specifically at lifting line theory, vortex lattice, equivalent beam, and equivalent plate methods, but could be used for other analysis techniques. The ability to output this information in both csv and Matlab file formats has been implemented in VSP. Ongoing work seeks …

Flow Uniformity Calibration Of Amelia's Circulation Control Wings, Eric N. Paciano, Johnathan A. Lichtwardt, David D. Marshall, Kristina K. Jameson, Robert K. Fong

Aerospace Engineering

This paper details the extensive effort required to achieve uniform now from the AMELIA wind tunnel model's circulation control wings. Performed in September of 2011 in the Fluid Mechanics Lab at NASA Ames Research Center, the calibration required a 500hp instrument-quality air compressor capable of delivering 250 CFM at pressures greater than 70 psL It was found that the geometery within AMELIA's circulation control supply plenums produced highly vortlcal flow, resulting in poor circulation control performance as measured by traversing external and stationary internal total pressure probes, as well as surface oil now. Adjustments were made within AMELIA to the …

Stol Performance Of Cal Poly's Amelia, Johnathan A. Lichtwardt, Eric N. Paciano, David D. Marshall, Kristina K. Jameson

Aerospace Engineering

Results from Cal Poly's recent wind tunnel test in the 40-by 80-foot test section at the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center are presented. AMELIA, the Advanced Model for Extreme Lift and Improved Aeroacoustics, is the first full-span cruise efficient short take-off and landing (CESTOL) model incorporating leading-and trailing-edge blowing wing circulation control and over-the-wing mounted turbine propulsion simulators (TPS) to date. Testing of the 10 foot span model proved successful and was the result of a 5-year NASA Fundamental Aeronautics Program Research Announcement. All of the results associated with Cal Poly's effort will be available …

Cal Poly's Amelia 10 Foot Span Hybrid Wing-Body Low Noise Cestol Aircraft Wing Tunnel Test And Experimental Results Overview, Kristina K. Jameson, David D. Marshall, Robert Ehrmann, Jonathon A. Lichtwardt, Eric N. Paciano, Robert J. Englar, William C. Hornes

Aerospace Engineering

A collaboration between California Polytechnic Corporation with Georgia Tech Research Institute (GTRI) and DHC Engineering worked on a NASA NRA to develop predictive capabilities for the design and performance of Cruise Efficient, Short Take-Off and Landing (CESTOL) subsonic aircraft. The work presented in this paper gives details of a large scale wind tunnel effort to validate predictive capabilities for this NRA for aerodynamic and acoustic performance during takeoff and landing. The model, Advanced Model for Extreme Lift and Improved Aeroacoustics {AMELIA), was designed as a 100 passenger, N+2 generation, regional, cruise efficient short takeoff and land (CESTOL) airliner with hybrid …