Engineering Commons^™

Design, Construction, And Evaluation Of A Portable Reusable Plastic Container Dumper, Kevin J. Lau

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and evaluation of a portable RPC (Reusable Plastic Container) dumper. This RPC dumper is one piece of a citrus processing system to package citrus. Bee Sweet currently utilizes man power in order to dump its RPCs whereas this design will decrease the amount of man power needed to dump RPCs during high workloads.

The goal of this project was to design, construct, and test a custom fabricated RPC dumper that will decrease the number of people needed to dump RPCs and also the amount of damage on the oranges when being dumped from …

Micro Sprinkler Irrigation Design On Almonds, Scott Trinta

BioResource and Agricultural Engineering

This project is to design a micro sprinkler system with a cost analysis for a 17 acre field. This type of irrigation will allow for a more uniform distribution of water, with more water being beneficially used at low flow rates. This design should minimize unwanted runoff water and save the farmer money in the long run.

Design, Construction, Testing, And Evaluation Of Water Trough Float Valves, Chad Reenders

BioResource and Agricultural Engineering

No abstract provided.

Design Of An Energy Efficient Virtual End Node Client Using Openadr2.0a And Smap, Kevin Navero

BioResource and Agricultural Engineering

Demand Response (DR) describes the set of actions taken to impose a reduction in electrical loads to stabilize the power grid and decrease costs. It is used when power grid emergencies or extremely high demand and congestion, threaten the electricity supply-demand balance. Automated Demand Response (ADR) describes a web-based control system that triggers DR events automatically by signaling other pre-programmed control systems. This project intends to use the OpenADR2.0 specifications provided by the OpenADR Alliance to construct an open source Virtual End Node (VEN) client to retrieve DR signals. The Simple Measurement and Actuation Profile (sMAP) software is also used …

Residential Fire Sprinkler Design For The Phi Kappa Psi Fraternity House, Nolan Frost

BioResource and Agricultural Engineering

This senior project discusses the design of a residential fire sprinkler system for a local fraternity house. The design follows NFPA 13D code, and contains design calculations, design drawings, material specifications, and cost analysis. The design was completed with the intention of being used for the installation of a fire sprinkler system in the house.

Design And Installation Of A Mobile Agriculture Chemical Mixing Station, Jason Mendes

BioResource and Agricultural Engineering

This senior project encompassed the design and fabrication of a Mobile Agricultural Chemical Mixing System. The design parameters were provided by Mark McKean and McKean Farms from Riverdale, Ca. The project’s objective was to provide safer working conditions for operators by improving their working environment while increasing mixing efficiency. This mobile system will provide storage for materials, as well as, a diversified mixing system at the site of applications.

The major components of the project include two chemical mixers to mix materials, a 2-inch suction pump to supply water from non-powered sources, and a flatbed trailer to encompass the unit …

The Visual Representation Of Sound For The Hearing Impaired, Jonathan Brophy

Electrical Engineering

There are many difficulties that arise when one is faced with a hearing disability. New applications of advancing technology have the potential to enable designs capable of assisting the hearing impaired with the ability to see sound. This project seeks to provide a user with a visual representation of loud noises detected using small directional microphones. The microphones determine the location of the sound above a set decibel level and a microprocessor determines the approximate location of the sound source and displays a vertical colored bar on a video image in the direction of the noise using virtual reality glasses. …

Unipolar Pulse Width Modulation Inverter, Randy Baggao, Gabriel Tam

Electrical Engineering

This project portrays the design and construction of a pulse width modulation (PWM) inverter. The inverter is implemented as a unipolar converter. The inverter provides a steady single-phase sinusoidal 60Hz AC voltage output from a DC input. This is a basic DC-AC power converter that is built in 3 separate phases and integrated altogether at the end. The inverter can be broken down into the control unit, firing circuit, and the H-bridge. By using the PWM method, one can control the frequency and amplitude of the output by using a reference signal. This method will also avoid using a transformer …

Low Speed Alternator Design, Scott Merrick

Electrical Engineering

No abstract provided.

Micro Hydropower System, Christpher Neally, Ian Verstuyft

Electrical Engineering

The micro hydropower project strives to meet the needs of a specific village in northern Thailand in partnership with Engineers Without Borders. Specifically, the electrical side of the system must be designed to convert the mechanical power of a flowing river that is turning a turbine into sustainable and dependable power. Currently available hydropower systems will be considered, analyzed, and tailored to suit the specific needs of the community in need. The system to be designed will be flexible enough to demonstrate proof-of-concept with the limited maximum generable power in lab while having the ability to be easily scaled for …

Universal-Retro Console Gamepads To Usb Adapter With Two-Player Compatibility, Miguel Buenrostro

Electrical Engineering

An Arduino board or microcontroller development board with a microprocessor can be configured to interface with a variety of wired gaming input devices. Through software and hardware design this functionality is accomplished for the use of older gaming system gamepad devices such as the original Nintendo Entertainment System, the Super Nintendo, and Sega Genesis. The Arduino development board offers up to 18 general purpose input output connections which are sufficient for the simultaneous connection of up to 6 gaming devices of the aforementioned gamepads. The microcontroller‘s firmware is changed to achieved plug-and-play compatibility so windows can recognize the device as …

Pscad Modeling Of One-Cycle Control Var, Andre Keir Azares

Electrical Engineering

Voltage support has been a common problem utilities have faced for many years and although there exists many solutions, the advent of renewable energy devices and electric vehicles make the problem of voltage support an even greater challenge today. The increasing use of electronic devices by consumers also increases the magnitude of dealing with voltage support. A promising new solution to voltage support is seen in One Cycle Control, a new control method that uses a nonlinear feedback technique on power electronics to produce high quality sine waves with fast dynamic response. This control paradigm is seen in its application …

Obd2 Pid Reader, Andrew Fong

Computer Engineering

The most current standard on automobiles for monitoring data is OBD-II. Using On board diagnostic Parameter ID (OBD PID) codes hobbyists and mechanics have the ability to monitor, chart, and obtain data on cars by communicating to the ECU. The OBD-II connector is often located under the driver’s side inside of the car. The hardware will consist of a generic Bluetooth OBD2 connector and a laptop running windows. The software will be an program exe created by visual basic. The software created in visual basic will allow the user to examine PID codes in order to record and discover new …

/Usr/Sbin/Clksync - Leo Nano-Statellite Clock Synchronization Software, Matt Zimmerer

Computer Engineering

A CalPoly Student Based Organization called Polysat takes mission contracts regarding the development and production of nano-satellites designed to fulfill specific mission requirements. Nano-satellites themselves are very complex and dense electronic devices. Polysat Satellites have recently switched to a new version of the main system board. This system board hosts an ARM AT91SAM92G0 processor, and enough hardware to comfortably run an embedded version of the Linux kernel. Each mission requires specific configuration for the system image, and specialized software. I've spent much of the last two years developing software, and recently debugging both my software, and the software system as …

Sifteo Spice, Ikenga Kenneth Ugo

Computer Engineering

Sifteo SPICE is an application built on the Sifteo platform with the purpose of aiding in the learning of basic circuits. Traditionally, circuit theory is taught to students in two different methods, lectures and laboratory exercises. Lectures focus on auditory and visual learning and are largely passive learning. Lab experiments allow students to physically interact with the circuits, and learn visually through viewing output waveforms from simulators or on measurement devices.[3] The goal of the Sifteo SPICE project is to develop a physical system for virtual, real-time SPICE simulation that mimics the laboratory experience. In Sifteo SPICE, each individual Sifteo …

Bluelock: A Secure Bluetooth Operated Padlock, Trever Mckee

Computer Engineering

For this project a secure, battery operated, Bluetooth operated padlock was created. The project included both the hardware to integrate with a padlock and an Android application used to interface with the hardware. In order to make the padlock secure both AES encryption and challenge response authentication were used for secure message passing between the device and the Android phone. The project also included power consumption and sustainability tuning including exploring Arduino sleep states and integrating the project with a solar charging unit.

Roborodentia Entry: Rob-Ot, Robert Mickle

Computer Engineering

No abstract provided.

Small Bear Project Shield, Janice A. Gelacio

Computer Engineering

The Small Bear Project Shield is an upgrade of the Power Control Board used in the Small Bear Project class, which utilizes the printed circuit board technology for a smaller structure. It has a connector that receives a 9V power through a wall wart, converted to 5V with a voltage regulator. It also has a connector to plug in a computer power supply. The power source is selected with a switch. The assembled board is used to power a stuffed animal bear that is built and programmed in the class.

Multiple Input Single Output (Miso) Tablet/ Phone Charger, Kevin Wong

Master's Theses

This thesis entails the design and implementation of a multiple input single output (MISO) DC-DC converter using the flyback topology to charge tablets/ smartphones or any USB powered portable device. The MISO converter will enable the use of various renewable energy sources such as a solar panel/ rechargeable battery combination, bicycle dynamo, hydroelectric power, and wind turbine. This paper will cover the design, simulations, and test results of the MISO converter. The flyback topology was chosen due to its low part count and its efficiency at low power. The proposed converter has a nominal 12V input to output USB 2.0 …

Real Time Visibility Culling With Hardware Occlusion Queries And Uniform Grids, Ilya Iseletsk Seletsky

Master's Theses

Culling out non-visible portions of 3D scenes is important for rendering large complex worlds at an interactive frame rate. Past 3D engines used static prebaked visibility data which was generated using complex algorithms. Hardware Occlusion Queries are a modern feature that allows engines to determine if objects are invisible on the fly. This allows for fully dynamic destructible and editable environments as opposed to static prebaked environments of the past. This paper presents an algorithm that uses Hardware Occlusion Queries to cull fully dynamic scenes in real-time. This algorithm is relatively simple in comparison to other real-time occlusion culling techniques, …

Design And Modeling Of Centralized Distribution Network For The Dc House Project, Harpreet S. Bassi

Master's Theses

This thesis focuses on the design, modeling, simulation, and performance evaluation of Centralized Distribution Network for the DC House Project. Power System Computer Aided Design (PSCAD) is used to model a Centralized PV Source, Battery Bank, and Distribution Network for 25 DC Houses. Design and modeling of each component in the proposed system are described. For the performance evaluation, emphasis is on voltage stability and system reliability under different operating conditions. Results from the simulation demonstrate the feasibility of the proposed Centralized Distribution Network for the DC House Project to support the houses during non-generation periods and distribution network voltage …

Manufacturing Execution System (Mes) An Examination Of Implementation Strategy, Riley F. Elliott

Master's Theses

The priorities of executing the manufacturing orders generated by an MRP system are often in operational conflicts with the dynamics of the manufacturing floor. It is not uncommon for a given manufacturing order to reach the shop floor several weeks or longer after being "opened" by an MRP system where it may face a chaotic case of large queues, machine down-time, parts shortage, scrap problems and other resource management constraints. Many companies have resorted to the Manufacturing Execution System (MES) software solution to resolve these problems. This method first gained popularity in mid-90’s within the semiconductor industry. An MES approach …

Dairy Manure Flushwater Treatment By Packed-Bed Anaerobic Digesters, Neal Cary Adler

Master's Theses

Wastewater treatment performance of three pilot-scale packed-bed anaerobic digesters with walnut shell medium was researched for treating dairy freestall barn flushwater. Reciprocation mixing was evaluated as a means to lessen channelization in the media bed and to improve biogas production and organic matter removal at ambient temperatures. Reciprocation has been used in biological nitrogen removal systems to introduce air into the system to repeatedly oxygenate nitrifying biofilm along with mixing (Behrends et al. 2003), but the anaerobic systems benefit from mixing. Two tanks were used in each system, where one was full and one was empty at any given time. …

Nutrient Removal Using Microalgae In Wastewater-Fed High Rate Ponds, Matthew N. Rodrigues

Master's Theses

This thesis discusses the mechanisms associated with the removal of organic matter, nitrogen and phosphorus in wastewater-fed high rate algae ponds (HRAP) designed to operate as triplicates. Research was conducted at the San Luis Obispo Water Reclamation Facility (SLOWRF) as a pilot-scale study of nine 30-square meter ponds one foot in depth. During period of study, triplicates were operated at hydraulic retention times (HRT) of 4, 3 or 2-days. Main objectives for the study were to determine minimum HRTs required to achieve secondary and tertiary treatment. Experimental conditions such as CO₂ supplementation, nighttime aeration and operation of ponds in …

Applied Hw/Sw Co-Design: Using The Kendall Tau Algorithm For Adaptive Pacing, Kenneth W. Chee

Master's Theses

Microcontrollers, the brains of embedded systems, have found their way into every aspect of our lives including medical devices such as pacemakers. Pacemakers provide life supporting functions to people therefore it is critical for these devices to meet their timing constraints. This thesis examines the use of hardware co-processing to accelerate the calculation time associated with the critical tasks of a pacemaker. In particular, we use an FPGA to accelerate a microcontroller’s calculation time of the Kendall Tau Rank Correlation Coefficient algorithm. The Kendall Tau Rank Correlation Coefficient is a statistical measure that determines the pacemaker’s voltage level for heart …

Human Powered Hydrofoil Bike Pontoon Floatation, Shelley Dangoor, Tyler Brennent

Mechanical Engineering

This report documents the brainstorming and design development of the hydrofoil bike floatation device. This project is in conjunction with senior project team MobyBike. MobyBike’s focus is in the development of the bike actuation system, as our team’s focus is on designing and developing the floatation device to be incorporated in the final hydrofoil bike design.

Hvac Lab, Adrian Leon, Wes Allen

Mechanical Engineering

The Cal Poly Heating Ventilation and Air Conditioning (HVAC) Department was donated a fume hood so that it could be used for educational purposes in the lab. The fume hood was not fully set up and only ran in a constant volume mode; the fan ran at full speed with no feedback to reduce air flow. A fume hood can be opened or closed using the sash; air flowing through the sash opening must always be above a certain speed. As the sash is closed the opening grows smaller and the speed of the air increases. Two additional modes of …

Adaptive Eating Device, Patrick Yale, Jillian Hiu, Jeremy Black, Kevin Farmer

Mechanical Engineering

No abstract provided.

Cal Poly Brocade Challenge 2013, Chandler Morehardt, Alexa Coburn, Juan Silva, Kerry Sun, Greg Wang, Raul Chagoya, Jd Torres

Architectural Engineering

No abstract provided.

Design And Analysis Of Reusable Nozzles For Cal Poly’S Hybrid Rocket Lab, Cheyne Austin, Jose Vargas

Aerospace Engineering

Two nozzles were designed and constructed for testing in the Cal Poly propulsion laboratory to explore which nozzle was the most capable in producing the most thrust. A 15 degree and 30 degree converging-diverging nozzles were machined and tested. Theory suggest that a bell nozzle would be the most efficient since all of the gasses generated in the combustion chamber are directed and accelerated by the throat leave the nozzle traveling along the thrust axis. All of the momentum of the gasses are directed axially thus resulting in maximum thrust. Thrust should also be produced by the converging-diverging nozzle and …