Engineering Commons^™

Kinematic/Static Model Of Complex Compliant Mechanisms With Serial-Parallel Substructures: A General Approach, Larry L. Howell, Mingxiang Ling, Junyi Cao

Faculty Publications

Kinematic and static analyses of compliant mechanisms are crucial at the early stage of design, and it can be difficult and laborsome for complex configurations with distributed compliance. In this paper, a general and concise kinematic/static modeling method of flexure-hinge-based compliant mechanisms with arbitrary serial-parallel substructures is presented to provide accurate and efficient solutions by combining the matrix displacement method with the transfer matrix method. The transition between the elemental stiffness matrix and the transfer matrix of the flexure hinge and the flexible beam is straightforward, enabling the condensation of a hybrid serial-parallel substructure into one equivalent element simple. Then, …

Distributed Electric Propulsion Effects On Traditional Aircraft Through Multidisciplinary Optimization, Kevin Moore, Andrew Ning

Faculty Publications

Electric aircraft face a steep tradeoff between the demand for runway performance and range. While fuel based propulsion technologies typically increase in specific power with increasing size, electric propulsion is typically much more scalable. This system scalability enables alternative designs including distributed propulsion, optionally powered propulsion units, and vectored thrust, which can all contribute to better runway performance and range. In this paper, we explore how continuously powered distributed propulsion can reduce takeoff distance while still satisfying range constraints. We use a combination of a blade element momentum method, a vortex lattice method, experimental data, and nonlinear optimization techniques to …

Benefits Of Two Turbine Rotor Diameters And Hub Heights In The Same Wind Farm, Andrew Pj Stanley, Andrew Ning, Katherine Dykes

Faculty Publications

Significant turbine-wake interactions greatly reduce power output in a wind farm. If different turbine hub heights and rotor diameters are included in the same wind farm, the wake interference in the farm will be reduced, resulting in a lower cost of energy (COE) than a farm with identical turbines. In this paper, we present a method to model wind farm COE in farms with hub heights and rotor diameters that vary across the wind farm. We also demonstrate how to optimize these wind farms to minimize COE. The results show that COE can be greatly reduced in wind farms with …

A Comparison Of Traditional And Adaptive Comparative Judgment Assessment Techniques For Freshmen Engineering Design Projects, Scott R. Bartholomew, Greg J. Strimel, Andrew Jackson

Faculty Publications

This article examines the use of an alternative form of assessment for engineering design projects called adaptive comparative judgment (ACJ). The researchers employed an ACJ tool to evaluate undergraduate engineering student design projects in an effort to examine its’ reliability, validity, and utility in comparison with traditional assessment techniques. The ACJ process employed multiple judges to compare the design artifacts of 16 first-year engineering majors. The authors conducted an analysis of the reliability and validity of the ACJ method compared to the traditional rubric used to evaluate the project and the performance data of each student’s design prototype. For these …

Characterization Of Pyrolysis Products From Fast Pyrolysis Of Live And Dead Vegetation Native To The Southern United States, Mohammad-Saeed Safdari, Mahmood Rahmati, Elham Amini, Joel E. Howarth, Jansen P. Berryhill, Mark Dietenberger, David R. Weise, Thomas H. Fletcher

Faculty Publications

Prescribed burning (controlled burning) is used to decrease accumulation of combustible materials and reduce impact of uncontrolled wildland fires. Prescribed fires are often used to burn undergrowth in Southern forests of the United States. In order to improve prescribed fire application, accomplish desired fire effects, and limit potential runaway fires, an improved understanding of the fundamental processes related to combustion of heterogeneous fuel beds of live and dead fuels is needed. The initial processes of combustion involve pyrolysis and ignition. During this research, fast pyrolysis of 14 live and dead (biomass) plant species which are native to the Southern United …

Effect Of Different Alumina Supports On Performance Of Cobalt Fischer-Tropsch Catalysts, Thomas H. Fletcher

Faculty Publications

Four identically-prepared 20 wt% cobalt/0.15 wt% ruthenium Fischer-Tropsch catalysts, supported on different aluminas, were synthesized by incipient wetness impregnation, characterized, and compared based on their performance under standard Fischer-Tropsch synthesis conditions. Three alumina supports were obtained from commercial sources (Sasol, St. Gobain, and Alfa Aesar), while the fourth was made using a published technique that included 5 wt% silica. The silica-stabilized alumina catalyst produced superior Fischer-Tropsch rates of 49 mmol CO/gcat h, compared to the other catalysts on the commercial supports with rates of 26–39 mmol CO/gcat h. The improved performance of the silica-stabilized alumina support compared to the commercially …

Development Of Bioreactors For Comparative Study Of Naturalattenuation, Biostimulation, And Bioaugmentation Ofpetroleum-Hydrocarbon Contaminated Soil, Mohammad-Saeed Safdari, Hamid-Reza Kariminia, Mahmood Rahmati, Farhad Fazlollahi, Alexandra Polasko, Shaily Mahendra, W Vincent Wilding, Thomas H. Fletcher

Faculty Publications

Bioremediation of soil and groundwater sites contaminated by petroleum hydrocarbons is known as a technically viable, cost-effective, and environmentally sustainable technology. The purpose of this study is to investigate laboratory-scale bioremediation of petroleum-hydrocarbon contaminated soil through development of eight bioreactors, two bioreactors for each bioremediation mode. The modes were: (1)natural attenuation (NA); (2) biostimulation (BS) with oxygen and nutrients; (3) bioaugmentation (BA)with hydrocarbon degrading isolates; (4) a combination of biostimulation and bioaugmentation (BS-BA). Total petroleum hydrocarbons (TPH) mass balance over the bioreactors showed about 2% of initial20,000 mg kg-soil−1TPH was removed by advection due to synthetic groundwater which was flow-ing …

Investigation Into Integrated Free-Form And Precomputational Approaches For Aerostructural Optimization Of Wind Turbine Blades, Ryan Timothy Barrett

Theses and Dissertations

A typical approach to optimize wind turbine blades separates the airfoil shape design from the blade planform design. This approach is sequential, where the airfoils along the blade span are pre-selected or optimized and then held constant during the blade planform optimization. In contrast, integrated blade design optimizes the airfoils and the blade planform concurrently and thereby has the potential to reduce cost of energy (COE) more than sequential design. Nevertheless, sequential design is commonly performed because of the ease of precomputation, or the ability to compute the airfoil analyses prior to the blade optimization. This research investigates two integrated …

Multidisciplinary Design Optimization Of Flexible Solar-Regenerative High-Altitude Long-Endurance Aircraft, Taylor Mcdonnell, Judd Mehr, Andrew Ning

Faculty Publications

Solar-Regenerative High-Altitude Long-Endurance (SR-HALE) aircraft are designed to sustain year-round flight at high altitudes indefinitely. No SR-HALE aircraft has yet accomplished this task due to the complex network of environmental, solar, structural, and aerodynamic trade-offs, among which aircraft flexibility plays a key role. A comprehensive SR-HALE aircraft multidisciplinary design optimization framework is developed in which the flexible aircraft analysis tool ASWING is incorporated in order to constrain nonlinear aeroelasticity. Energy, battery, ply thickness, material failure, local buckling, aerodynamic stall, longitudinal stability, and general stability (including flutter) constraints are applied in order to reasonably constrain the optimized SR-HALE aircraft design. An …

Complete Measurement System For Measuring High Voltage And Electrical Field Using Slab-Coupled Optical Fiber Sensors, Nikola Stan

Theses and Dissertations

A slab-coupled optical fiber sensor (SCOS) falls into a narrow class of all-dielectric optical fiber electric field sensors, which makes it a perfect candidate for measurements of high electric fields in environments where presence of conductors is highly perturbing to the system under test. Its nonlinear response to high fields requires a new nonlinear calibration technique. A nonlinear calibration method is explained and demonstrated to successfully measure high electric fields, as well as high voltages with dynamic range up to 50 dB. Furthermore, a SCOS can be fitted into narrow spaces and make highly localized measurements due to its small …

Large-Scale Multidisciplinary Optimization Of An Electric Aircraft For On-Demand Mobility, John Hwang, Andrew Ning

Faculty Publications

Distributed electric propulsion is a key enabling technology for on-demand electric aircraft concepts. NASA’s X-57 Maxwell X-plane is a demonstrator for this technology, and it features a row of high-lift propellers distributed along the leading edge of its wing to enable better aerodynamic efficiency at cruise and improved ride quality in addition to less noise and emissions. This study applies adjoint- based multidisciplinary design optimization to this highly coupled design problem. The propulsion, aerodynamics, and structures are modeled using blade element momentum theory, the vortex lat- tice method, and finite element analysis, respectively, and the full mission profile is discretized …

Impact Of Vapor Polishing On Surface Quality And Mechanical Properties Of Extruded Abs, Clayton Neff, Matthew Trapuzzano, Nathan B. Crane

Faculty Publications

Purpose — Additive manufacturing (AM) is readily capable of producing models and prototypes of complex geometry and is advancing in creating functional parts. However, AM processes typically underperform traditional manufacturing methods in mechanical properties, surface roughness, and hermeticity. Solvent vapor treatments (vapor polishing) are commonly used to improve surface quality in thermoplastic parts, but the results are poorly characterized.

Design/methodology/approach — This work quantifies the surface roughness change and also evaluates the effect on hermeticity and mechanical property impacts for “as-printed” and acetone vapor-polished ABS tensile specimens of 1, 2, and 4 mm thicknesses produced by material extrusion (FDM).

Findings …

Controlling Normal Stiffness In Droplet-Based Linear Bearings, Qi Ni, Nathan B. Crane

Faculty Publications

While Capillary forces are negligible relative to gravity at the macroscale, they provide adequate force to effectively manipulate millimeter to micro meter objects. The fluidic actuation can be accomplished using droplets that also act as bearings. While rotary droplet bearings have been previously demonstrated, this paper considers the performance potential of discrete droplets acting as linear bearings. Specifically, it addresses the positioning accuracy of a droplet-based bearing consisting of a droplet between a moving plate and a stationary substrate with constrained wetting region under a normal load using both closed form analytical solutions and numerical simulations. The vertical force and …

Examining Engineering Design Cognition With Respect To Student Experience And Performance, Greg J. Strimel, Eunhye Kim, Scott R. Bartholomew, Diana V. Cantu

Faculty Publications

This study investigated the design cognition and performance results of secondary and post-secondary engineering students while engaged in an engineering design task. Relationships between prototype performance and design cognition were highlighted to investigate potential links between cognitive processes and success on engineering design problems. Concurrent think-aloud protocols were collected from eight secondary and 12 post-secondary engineering students working individually to design, make, and evaluate a solution prototype to an engineering design task. The collected protocols were segmented and coded using a pre-established coding scheme. The results were then analyzed to compare the two participant groups and determine the relationships between …

Adaptive Comparative Judgment For Polytechnic Transformation: Assessment Across The Curriculum, Scott R. Bartholomew, P. E. Connolly

Faculty Publications

The authors are investigating potential applications of adaptive comparative judgment (ACJ) across numerous environments and learning scenarios within the Purdue Polytechnic Institute as part of Purdue’s efforts to transform the undergraduate learning experience. Six courses or program areas were selected for the study, involving a wide variation in subjects, subject matter, and assessment artifacts. The authors anticipate that positive results from these pilot studies will encourage broader and deeper applications of ACJ in the Purdue Polytechnic, across Purdue University, and in other academic institutions. Results from these scenarios will be disseminated in future conferences and scholarly journals.

Effects Of Ag Promotion And Preparation Method On Cobalt Fischer- Tropsch Catalysts Supported On Silica-Modified Alumina, Mahmood Rahmati, Baiyu Huang, Landon M. Schofield, Thomas H. Fletcher, Brian F. Woodfield, William C. Hecker, Calvin H. Bartholomew, Morris D. Argyle

Faculty Publications

A series of silver-promoted, 20 wt% cobalt Fischer-Tropsch synthesis (FTS) catalysts supported on an alumina modified with 5 wt% silica were prepared using two methods: traditional incipient wetness impregnation (IWI) and a new solvent deficient precipitation (SDP) technique. Catalysts containing silver promoter concentrations of 0.3, 0.6, 1.2, and 2.5 wt% were prepared using each of the two methods. Silver improved the reducibility of the cobalt significantly, lowering reduction temperatures by up to 100 C, and increasing the extent of reduction by up to 35%. Further, in both preparation methods, changing the silver loading altered the cobalt dispersion. The smallest Co …

Formation Of Deposits From Heavy Fuel Oil Ash In An Accelerated Deposition Facility At Temperatures Up To 1219 °C, Robert Laycock, Thomas H. Fletcher

Faculty Publications

Some industrial gas turbines are currently being fired using heavy fuel oil, which contains a small percentage of inorganic material that can lead to fouling and corrosion of turbine components. Deposits of heavy fuel oil ash were created in the Turbine Accelerated Deposition Facility (TADF) at Brigham Young University under gas turbine-related conditions. Ash was produced by burning heavy fuel oil in a downward-fired combustor and collecting the ash from the exhaust stream. This ash was then introduced into the TADF and entrained in a hot gas flow that varied from 1101 °C to 1219 °C. Sulfur dioxide was introduced …

Fire Behavior In Chaparral–Evaluating Flame Models With Laboratory Data, David R. Weise, Thomas H. Fletcher, Wesley Cole, Shankar Mahalingam, Xiangyang Zhou, Lulu Sun, Jing Li

Faculty Publications

Flame and mass loss data for chaparral, a mixture of shrub plants from the Mediterranean climate zone of southwestern North America, from five previously reported experiments were used to evaluate several published models relating flame characteristics to mass loss and heat release rates. These data are unique with fuel moisture content ranging from 0.36 to 0.94 (dry basis); the study used mass loss rates which included water loss. Fit of the data to Froude number correlations developed by Albini, Byram, Nelson and Thomas and heat release rate—flame length correlations by Heskestad, Zukoski, and Yuan/Cox for axisymmetric and line fires were …

Lab-Scale Observations Of Flame Attachment On Slopes With Implications For Firefighter Safety Zones, Jonathan R. Gallacher, Brad Ripa, Bret W. Butler, Thomas H. Fletcher

Faculty Publications

The Coanda effect is the phenomenon in which a jet entering quiescent fluid attaches to a nearby solid object due to inhibited entrainment of ambient fluid near the solid. Little is known about the influence of the Coanda effect on wildland fire behavior. Specifically, there is a lack of knowledge regarding how the flame attachment on slopes influences firefighter safety zone considerations in rugged terrain. This paper presents results for small-scale n-heptane pool fire experiments near a slope, showing how flame shape and heat flux are influenced by slope angle, slope boundary condition and distance from flame base. Flames near …

Combined Noncyclic Scheduling And Advanced Control For Continuous Chemical Processes, Damon Petersen, Logan D. R. Beal, Derek Prestwich, Sean Warnick, John Hedengren

Faculty Publications

A novel formulation for combined scheduling and control of multi-product, continuous chemical processes is introduced in which nonlinear model predictive control (NMPC) and noncyclic continuous-time scheduling are efficiently combined. A decomposition into nonlinear programming (NLP) dynamic optimization problems and mixed-integer linear programming (MILP) problems, without iterative alternation, allows for computationally light solution. An iterative method is introduced to determine the number of production slots for a noncyclic schedule during a prediction horizon. A filter method is introduced to reduce the number of MILP problems required. The formulation’s closed-loop performance with both process disturbances and updated market conditions is demonstrated through …

Carbon Nanotube Prosthetic Venous Valve, Ryan Coulton Packer

Theses and Dissertations

Chronic Venous Insufficiency (CVI) is a disease of the lower limbs that affects millions of people in the United States. It is categorized by constant venous hypertension, which can lead to swelling of the legs, pain, skin changes and ulcers. One of the widely known symptoms that can lead to CVI is varicose veins. The main source of the problem of CVI is incompetent venous valves. The purpose of venous valves is to direct blood through the veins to the heart and prevent retrograde flow to the lower limbs. CVI can be caused by leg injury, pregnancy, genetics, age, and …

A Robust Synthetic Basis Feature Descriptor Implementation And Applications Pertaining To Visual Odometry, Object Detection, And Image Stitching, Lindsey Ann Raven

Theses and Dissertations

Feature detection and matching is an important step in many object tracking and detection algorithms. This paper discusses methods to improve upon previous work on the SYnthetic BAsis feature descriptor (SYBA) algorithm, which describes and compares image features in an efficient and discreet manner. SYBA utilizes synthetic basis images overlaid on a feature region of interest (FRI) to generate binary numbers that uniquely describe the feature contained within the FRI. These binary numbers are then used to compare against feature values in subsequent images for matching. However, in a non-ideal environment the accuracy of the feature matching suffers due to …

Strain Path Effect On Austenite Transformation And Ductility In Q&P 1180 Steel, Jeffrey Grant Cramer

Theses and Dissertations

The ductility of Q&P 1180 steel was studied with regard to retained austenite transformation under different strain paths. Specimens were tested in uniaxial tension in a standard test frame as well as in situ in the scanning electron microscope (SEM). Then digital image correlation (DIC) was used to compute the effective strain at the level of the individual phases in the microstructure. Stretching experiments were also performed using limiting dome height (LDH) tooling, where specimens were strained in both biaxial and plane strain tension. The experiments were done incrementally, for each strain path, and the retained austenite at each level …

Relative Navigation Of Micro Air Vehicles In Gps-Degraded Environments, David Orton Wheeler

Theses and Dissertations

Most micro air vehicles rely heavily on reliable GPS measurements for proper estimation and control, and therefore struggle in GPS-degraded environments. When GPS is not available, the global position and heading of the vehicle is unobservable. This dissertation establishes the theoretical and practical advantages of a relative navigation framework for MAV navigation in GPS-degraded environments. This dissertation explores how the consistency, accuracy, and stability of current navigation approaches degrade during prolonged GPS dropout and in the presence of heading uncertainty. Relative navigation (RN) is presented as an alternative approach that maintains observability by working with respect to a local coordinate …

Real-Time Beamforming Algorithms For The Focal L-Band Array On The Green Bank Telescope, Mark William Ruzindana

Theses and Dissertations

A phased array feed (PAF) provides a contiguous, electronically synthesized wide field of view for large-dish astronomical observatories. Significant progress has been made in recent years in improving the sensitivity of PAF receivers though optimizing the design of the antenna array, cryogenic cooling of the front end, and implementation of real-time correlation and beamforming in digital signal processing. FLAG is a 19 dual-polarized element phased array with cryogenic LNAs, direct digitization of RF signals at the front end, digital signal transport over fiber, and a real time signal processing back end with up to 150 MHz bandwidth. The digital back …

Design And Analysis Of Compressed Air Power Harvesting Systems, Zachary James Sadler

Theses and Dissertations

Procedure for site discovery, system design, and optimization of power harvesting systems is developed with an emphasis on application to air compressors. Limitations for the usage of infrared pyrometers is evaluated. A system of governing equations for thermoelectric generators is developed. A solution method for solving the system of equations is created in order to predict power output from the device. Payback analysis is proposed for determining economic viability. A genetic algorithm is used to optimize the power harvesting system payback with changing quantities and varieties of thermoelectric generators, as well as the back work put into cooling the thermoelectric …

Trading Off Sound Pressure Level And Average Power Production For Wind Farm Layout Optimization, Eric Tingey, Andrew Ning

Faculty Publications

This research explores the trade-offs between a wind farm’s average power production and noise impact on nearby observers. Two specific wind farm designs were studied and optimized using the FLORIS wake model and an acoustic model based on semi-empirical turbine noise calculations. It was found in the two wind farms that the average power production could be increased, up to 8.01% in one and 3.63% in the other, ignoring sound level considerations. Including a noise restriction in the optimization had a minimal impact on the optimal average power production within about a five-decibel range. Past this range, sound limitations decreased …

An Analysis Of The Size And Impact Of Digital Footprints, Whitney Nielsen Maxwell

Theses and Dissertations

Personal information available online is known as a digital footprint. While many have a digital footprint, few if any, know what it encapsulates or how to control it. Technology and personal information are becoming more intertwined as technology becomes more integrated with everyday activities. Personal information can be defined as details that apply to a person such as race or shopping habits. Shopping habits are considered personal information by many corporations who spend money to track, or even predict purchases of individuals, whereas more traditional forms of personal information are details like gender, birthdate, and home town. With a wide …

Project Management: Skills, Tools, And Knowledge Construction Professionals Consider Important For Keeping Projects On Schedule, Lyle Scott Davies

Theses and Dissertations

Project managers have a major role in the construction and completion of projects. Much of their work consists of reviewing, clarifying, and coordinating information required by the field management and subcontractors performing the work on the job site. The assistance they give with the transfer of information helps with successfully completing projects. For many people, the largest indicator that a project was successful is that construction activities were completed on schedule. While finishing on schedule may be the primary focus of those involved with construction activities, projects still struggle to finish on time. The purpose of this study is to …

Advancements In Radio Astronomical Array Processing: Digital Back End Development And Interferometric Array Interference Mitigation, Mitchell Costus Burnett

Theses and Dissertations

The Brigham Young University (BYU) Radio Astronomy Systems group, in collaboration with the National Radio Astronomy Observatory (NRAO), the Center for Astrophysics at West Virginia University (WVU), and the Green Bank Observatory (GBO) have developed, and commissioned, a broadband real-time digital back end processing system for a 38-element phased array feed (PAF) with 150 MHz of instantaneous bandwidth. This system is capable of producing coarse and fine channel correlations, and implements a real-time beamformer that forms 7 simultaneous dual-polarized beams. This thesis outlines the hardware and software development for the digital back end and presents on-telescope commissioning results. This system …