Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- Composite materials (15)
- Photoluminescence (11)
- Silicon carbide (11)
- Additive manufacturing (9)
- Ceramic-matrix composites--Fatigue (9)
-
- Ceramic-matrix composites (6)
- Lasers (6)
- Quantum wells (6)
- Thin films (6)
- Ceramic-matrix composites--Creep (5)
- Composite materials--Creep (5)
- Materials--Fatigue (5)
- Nonlinear optics (5)
- Optical fibers (5)
- Oxidation (5)
- Composite materials--Testing (4)
- Creep (4)
- Fatigue (Mechanics) (4)
- Fretting corrosion (4)
- Gallium arsenide (4)
- Ion implantation (4)
- Metamaterials (4)
- Semiconductor lasers (4)
- Atomic force microscopy (3)
- Ceramic Matrix Composites (3)
- Ceramic matrix composite (3)
- Composite Materials (3)
- Doped semiconductors (3)
- Electron paramagnetic resonance spectroscopy (3)
- Gallium arsenide semiconductors (3)
- Publication Year
- Publication Type
Articles 31 - 60 of 276
Full-Text Articles in Engineering
Creep Behavior And Deformation Mechanisms Of Spark Plasma Sintered Oxide Ceramics For Aerospace Systems At 1300˚C - 1400˚C, David D. Swanson
Creep Behavior And Deformation Mechanisms Of Spark Plasma Sintered Oxide Ceramics For Aerospace Systems At 1300˚C - 1400˚C, David D. Swanson
Theses and Dissertations
The mechanical behavior of YAG and LuAG was investigated at elevated temperatures. The specific materials investigated in this work include high-purity, polycrystalline YAG, high-purity, polycrystalline LuAG, and two doped variants of YAG: 2at% Yb-doped, polycrystalline YAG and 2at% Er-doped, polycrystalline YAG. Several billets of each material were prepared and processed by means of spark plasma sintering (SPS). Many different sintering parameters were utilized in order to obtain materials with various physical properties and to identify the effects of sintering parameters on the average grain size of the resulting materials. The compressive creep behavior of these materials was investigated at 1300°C …
Optically Active Selenium Vacancies In Baga4Se7 Crystals, Brian C. Holloway, Timothy D. Gustafson, Christopher A. Lenyk, Nancy C. Giles, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Larry E. Halliburton
Optically Active Selenium Vacancies In Baga4Se7 Crystals, Brian C. Holloway, Timothy D. Gustafson, Christopher A. Lenyk, Nancy C. Giles, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Larry E. Halliburton
Faculty Publications
Barium gallium selenide (BaGa4Se7) is a recently developed nonlinear optical material with a transmission window extending from 470 nm to 17 μm. A primary application of these crystals is the production of tunable mid-infrared laser beams via optical parametric oscillation. Unintentional point defects, such as selenium vacancies, cation vacancies (barium and/or gallium), and trace amounts of transition-metal ions, are present in BaGa4Se7 crystals and may adversely affect device performance. Electron paramagnetic resonance (EPR) and optical absorption are used to identify and characterize these defects. Five distinct EPR spectra, each representing an electron …
Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith
Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith
AFIT Patents
A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.
Improvements To Emissive Plume And Shock Wave Diagnostics And Interpretation During Pulsed Laser Ablation Of Graphite, Timothy I. Calver
Improvements To Emissive Plume And Shock Wave Diagnostics And Interpretation During Pulsed Laser Ablation Of Graphite, Timothy I. Calver
Theses and Dissertations
This dissertation covers nanosecond pulsed laser ablation of graphite for 4-5.7 J/cm2 fluences with 248 nm and 532 nm lasers in 1-180 Torr helium, argon, nitrogen, air, and mixed gas. Three experiments were performed to improve the interpretation of common diagnostics used to characterize pulsed laser ablation, find simple but universal scaling relationships for comparing dynamics across different materials and ablation conditions, and provide a systematic analysis of graphite emissive plume and shock wave dynamics. A scaling of the Sedov-Taylor energy ratio was developed and validated for a range of studies despite differences in wavelength, pulse duration, fluence, and …
Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily
Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily
Theses and Dissertations
This thesis systematically goes through the derivation, simulation, and experimentation of Zinc Oxide optofluidic micro laser elements. Single and coupled ring resonators were simulated to show single mode transmission as well as enhanced coupling capabilities when surrounded by high refractive index liquid. Devices with diameters ranging from 100-500 µm were successfully fabricated inexpensively through standard cleanroom procedures. The devices were tested using two different pump laser systems. Testing included such factors as high pump intensity, various angles of excitation, and low temperature. In all cases PL emission was observed and recorded.
Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith
Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith
AFIT Patents
A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.
Fatigue Of Two Oxide/Oxide Ceramic Matrix Composites At 1200°C In Air And In Steam. Effect Of Diamond Drilled Effusion Holes, Anthony R. Cabri
Fatigue Of Two Oxide/Oxide Ceramic Matrix Composites At 1200°C In Air And In Steam. Effect Of Diamond Drilled Effusion Holes, Anthony R. Cabri
Theses and Dissertations
The tension-tension fatigue behavior of two oxide-oxide ceramic matrix composites (CMCs) was investigated at 1200°C in laboratory air and steam. Both composites consist of a porous oxide matrix reinforced with laminated, woven mullite/alumina (NextelTM720) fibers. The first composite had an alumina matrix, while the second had an alumina-mullite matrix. First, we assessed the effects of incorporating mullite into the matrix material on fatigue performance by studying the tension-tension fatigue behavior of alumina-mullite matrix CMC. Second, we evaluated the effects of effusion holes on the alumina matrix CMC's fatigue performance. Specimens containing an array of 17 effusion holes of 0.5-mm diameter …
Static Fatigue Of Hi-Nicalon™ S Ceramic Fiber Tows At 600°C In Air And Silicic Acid-Saturated Steam, Caleigh M. Nelson
Static Fatigue Of Hi-Nicalon™ S Ceramic Fiber Tows At 600°C In Air And Silicic Acid-Saturated Steam, Caleigh M. Nelson
Theses and Dissertations
Ceramic matrix composites (CMCs) have the potential to be utilized in applications such as hypersonic vehicles, aircraft leading edges, hot sections of engines, and rocket nozzles. Of particular interest are advanced SiC/SiC composites that can withstand the elevated temperatures and harsh oxidizing environments while maintaining their properties and structural integrity under an applied load. Steam, a major component of combustion environment, is one such aggressive oxidizing environment. As steam passes through the SiC/SiC composite, entering the composite interior through the cracks in the SiC matrix, it becomes saturated with silicic acid, Si(OH)4. Before incorporating SiC/SiC composites in the …
Static Fatigue Of Hi-Nicalon S Fiber Tows At 500°C In Air And In Silicic Acid-Saturated Steam, Richard J. Reinink
Static Fatigue Of Hi-Nicalon S Fiber Tows At 500°C In Air And In Silicic Acid-Saturated Steam, Richard J. Reinink
Theses and Dissertations
Recent developments in aerospace propulsion systems, along with emerging interest in hypersonic air vehicles has emphasized the need for materials which can withstand extreme service environments. The leading candidates for the structural components expected to operate in these environments are SiC-based ceramic matrix composites (CMCs). When a CMC component is subjected to thermomechanical loads in an aggressive environment during service, surface cracks form. As steam penetrates cracks in the SiC matrix, it becomes saturated with silicic acid, (SI(OH)4) and attacks the SiC fibers. The interaction between the Hi-Nicalon™ S SiC fibers and the (SI(OH)4)-saturated steam is …
Photoinduced Trapping Of Charge At Sulfur Vacancies And Copper Ions In Photorefractive Sn2P2S6 Crystals, Timothy D. Gustafson, Eric M. Golden, Elizabeth M. Scherrer, Nancy C. Giles, A. A. Grabar, Sergey A. Basun, Jonathan E. Slagle, Larry E. Halliburton
Photoinduced Trapping Of Charge At Sulfur Vacancies And Copper Ions In Photorefractive Sn2P2S6 Crystals, Timothy D. Gustafson, Eric M. Golden, Elizabeth M. Scherrer, Nancy C. Giles, A. A. Grabar, Sergey A. Basun, Jonathan E. Slagle, Larry E. Halliburton
Faculty Publications
Electron paramagnetic resonance (EPR) is used to monitor photoinduced changes in the charge states of sulfur vacancies and Cu ions in tin hypothiodiphosphate. A Sn2P2S6 crystal containing Cu+ (3d10) ions at Sn2+ sites was grown by the chemical vapor transport method. Doubly ionized sulfur vacancies (V2+S) are also present in the as-grown crystal (where they serve as charge compensators for the Cu+ ions). For temperatures below 70 K, exposure to 532 or 633 nm laser light produces stable Cu2+ (3d9) ions, as electrons move from Cu+ ions to …
A Computational Investigation Of The Interstitial Oxidation Thermodynamics Of A Mo-Nb-Ta-W High Entropy Alloy Beyond The Dilute Regime, Adib J. Samin
A Computational Investigation Of The Interstitial Oxidation Thermodynamics Of A Mo-Nb-Ta-W High Entropy Alloy Beyond The Dilute Regime, Adib J. Samin
Faculty Publications
High entropy alloys (HEAs) are promising candidates for high-temperature structural material applications. Oxidation is a major factor that must be accounted for when designing such materials and it is thus important to study the oxidation behavior of HEAs to enable the optimum design of next generation materials. In this study, the thermodynamic behavior of interstitial oxygen in a Mo-Nb-Ta-W high entropy alloy was explored beyond the dilute limit. This was accomplished by sampling configurations of the HEA and HEA-oxygen systems from an isothermal–isobaric ensemble using a series of first-principle-based Monte Carlo simulations. It was found that the interstitial oxygen had …
3-D Fabry–Pérot Cavities Sculpted On Fiber Tips Using A Multiphoton Polymerization Process, Jonathan W. Smith, Jeremiah C. Williams, Joseph S. Suelzer, Nicholas G. Usechak, Hengky Chandrahalim
3-D Fabry–Pérot Cavities Sculpted On Fiber Tips Using A Multiphoton Polymerization Process, Jonathan W. Smith, Jeremiah C. Williams, Joseph S. Suelzer, Nicholas G. Usechak, Hengky Chandrahalim
Faculty Publications
This paper presents 3-D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3-D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity's reflection spectrum. The …
Temporally Multiplexed Ladar Polarimeter, Christian Keyser, Richard Kenneth Martin
Temporally Multiplexed Ladar Polarimeter, Christian Keyser, Richard Kenneth Martin
AFIT Patents
In a polarimeter, a polarization modulator changes a polarization phase of an output optical pulse with a modulation function that varies in time over the duration of the optical pulse. A static polarization state analyzer, which includes a one or more static polarization component analyzers and detectors, receives the modulated optical pulse after interaction with a target medium and provides time varying intensities of the polarization components of the received pulse. A signal processing module determines a polarization property of the target medium, such as a Mueller matrix, dependent upon time varied intensities over the duration of the received optical …
Nonlinear Optical Measurements Of Cdsip2 At Near And Mid-Infrared Wavelengths, Manuel R. Ferdinandus, Jamie J. Gengler, Kent L. Averett, Kevin T. Zawilski, Peter G. Schunemann, Carl M. Liebig
Nonlinear Optical Measurements Of Cdsip2 At Near And Mid-Infrared Wavelengths, Manuel R. Ferdinandus, Jamie J. Gengler, Kent L. Averett, Kevin T. Zawilski, Peter G. Schunemann, Carl M. Liebig
Faculty Publications
We measure the birefringence of the nonlinear optical (NLO) properties of cadmium silicon phosphide via the Z-scan technique at near and mid-infrared wavelengths. We discuss the implications of the NLO properties on optical parametric amplifier performance. We find that the nonlinear absorption does reduce the conversion efficiency, while the nonlinear refraction has a negligible effect.
Tension-Tension Fatigue Behavior Of Nextel™ 720/Alumina-Mullite Ceramic Composite At 1200°C In Air And In Steam, Sarah A. Witzgall
Tension-Tension Fatigue Behavior Of Nextel™ 720/Alumina-Mullite Ceramic Composite At 1200°C In Air And In Steam, Sarah A. Witzgall
Theses and Dissertations
Uniaxial tension-tension fatigue performance of an oxide-oxide continuous fiber ceramic composite was studied at 1200°C in laboratory air and in steam. The composite is reinforced with laminated, 0/90 mullite/alumina (NEXTEL™720) fibers woven in an eight-harness satin weave and has a porous alumina/mullite matrix. There is no interphase between the fiber and matrix. The composite relies on the porous matrix for crack deflection and flaw tolerance. Tension-tension fatigue was examined for maximum stresses of 45 – 136 MPa in air and in steam. To assess the effects of the steam environment on fatigue performance, experimental results obtained in air are compared …
Experimental Determination Of The (0/−) Level For Mg Acceptors In Β-Ga2O3 Crystals, Christopher A. Lenyk, Trevor A . Gustafson, Sergey A. Basun, Larry E. Halliburton, Nancy C. Giles
Experimental Determination Of The (0/−) Level For Mg Acceptors In Β-Ga2O3 Crystals, Christopher A. Lenyk, Trevor A . Gustafson, Sergey A. Basun, Larry E. Halliburton, Nancy C. Giles
Faculty Publications
Electron paramagnetic resonance (EPR) is used to experimentally determine the (0/−) level of the Mg acceptor in an Mg-doped β-Ga2O3 crystal. Our results place this level 0.65 eV (±0.05 eV) above the valence band, a position closer to the valence band than the predictions of several recent computational studies. The crystal used in this investigation was grown by the Czochralski method and contains large concentrations of Mg acceptors and Ir donors, as well as a small concentration of Fe ions and an even smaller concentration of Cr ions. Below room temperature, illumination with 325 nm laser light …
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Investigation Of Ultem 9085 For Use In Printed Orbital Structures, William R. Gallagher
Theses and Dissertations
Additive manufacturing is revolutionizing industries ranging from medicine to space. However, the structural characteristics of plastic parts created by these methods are not as well understood as their more established counterparts. This research explored two relevant areas: how the structural characteristics of ULTEM 9085 plastic behaved after exposure to orbital conditions and the design of the cross-sectional area of a beam to be 3-D printed in microgravity based on the expected loads from the printer. To study orbital effects, ULTEM 9085 was printed into 1/4th scale ASTM D638- 14 dogbones using a Stratasys 450mc printer. These dogbones were placed in …
Dynamic Micromechanical Fabry-Perot Cavity Sensors Fabricated By Multiphoton Absorption Onto Optical Fiber Tips, Jeremiah C. Williams
Dynamic Micromechanical Fabry-Perot Cavity Sensors Fabricated By Multiphoton Absorption Onto Optical Fiber Tips, Jeremiah C. Williams
Theses and Dissertations
This research leveraged two-photon polymerization microfabrication to integrate dynamic mechanical components with Fabry-Perot resonators onto the ends of low-loss optical fibers to prototype 3 micro-optic devices. The first device featured a multi-positional mirror that enabled thin-film deposition onto cavities of any length with mirrors of significant curvature, for refractive index sensing. The second device combined an FP cavity with a spring body featuring easily scalable stiffness for pressure sensing. The third device presented a high-speed rotating micro-anemometer for measuring a wide range of gas flows. All devices represent a significant reduction in size and weight over commercially available devices.
Wideband Metasurface Antenna, Thomas A. Lepley
Wideband Metasurface Antenna, Thomas A. Lepley
Theses and Dissertations
This effort explored design of metasurface antennas and evaluated their suitability for ultra-wideband applications (2 to 18 GHz). Six unit cell types were characterized. Eigenmode simulations produced frequency vs. phase data for the unit cells, from which impedance vs. gap size data was computed. A holographic design equation was used to generate the metasurface antenna designs. The unit cell simulations revealed that the assumption of single mode operation is a constraint for wideband designs. An 8" by 8" metasurface antenna with a Rogers 3010 dielectric and a design frequency of 10 GHz was fabricated and tested. It had a 1.5:1 …
Alternate Materials For High-Speed Projectile Casing, Andrew W. Beard
Alternate Materials For High-Speed Projectile Casing, Andrew W. Beard
Theses and Dissertations
A high-speed projectile impact is a highly complex dynamic problem that can be simplified with the use of finite element analysis solvers. Abaqus/Explicit was used to evaluate the impact of various projectiles using a plane strain setup. Using a baseline stainless steel projectile, the proposed sandwich construction design was analyzed and compared to the baseline projectile. The overall goal was to see if a new composite casing could perform similarly to the simple baseline projectile. The sandwich construction used stainless steel, tungsten, and silicon-carbide reinforce aluminum as outer and inner shell materials. The core material was created using additive manufacturing …
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Solution Anneal Heat Treatments To Enhance Mechanical Performance Of Additively Manufactured Inconel 718, David J. Newell
Theses and Dissertations
The nickel-based superalloy Inconel 718 (IN718) is an excellent candidate among aerospace alloys for laser powder-bed fusion (LPBF) manufacturing. As-built LPBF IN718 has a vertically aligned columnar (001) microstructure which translates into orthotropic mechanical behavior. The post-process heat treatments for IN718 were developed 60 years ago for wrought and cast processes and do not mitigate the columnar microstructure of the LPBF process. Recrystallization is required to remove the columnar microstructure, which would allow for parts to be fabricated on different machines or in different orientations but still achieve the same properties. This research investigated the microstructure of LPBF IN718 as …
Fatigue Behavior Of An Advanced Melt-Infiltrated Sic/Sic Composite With Environmental Barrier Coating At 1200°C In Air And In Steam, Thaddeus M. Williams
Fatigue Behavior Of An Advanced Melt-Infiltrated Sic/Sic Composite With Environmental Barrier Coating At 1200°C In Air And In Steam, Thaddeus M. Williams
Theses and Dissertations
Advanced aerospace applications such as aircraft turbine engine components, hypersonic flight vehicles, and spacecraft reentry thermal protection systems require structural materials that have superior long-term mechanical properties under high temperature, high pressure, and varying environmental factors, such as moisture. Because of their low density, high strength and fracture toughness at high temperatures SiC fiber-reinforced SiC matrix composites are being evaluated for aircraft engine hot-section components. In these applications the composites will be subjected to various types of mechanical loadings at elevated temperatures in oxidizing environments. Because their constituents are intrinsically oxidation-prone, the most significant problem hindering SiC/SiC composites is oxidation …
The Design Of A Continuous Wave Molecular Nitrogen Stimulated Raman Laser In The Visible Spectrum, Timothy J. Bate
The Design Of A Continuous Wave Molecular Nitrogen Stimulated Raman Laser In The Visible Spectrum, Timothy J. Bate
Theses and Dissertations
Hollow-core photonic crystal fibers (HCPCFs) shows promise as a hybrid laser with higher nonlinear process limits and small beam size over long gain lengths. This work focuses on the design of a CW molecular nitrogen (N2) stimulated Raman laser. N2 offers Raman gains scaling up to 900 amg, scaling higher than H2. The cavity experiment showed the need to include Rayleigh scattering in the high pressure required for N2 Raman lasing. Even at relatively low pressure ssuch as 1,500 psi, high conversion percentages should be found if the fiber length is chosen based on …
Cn And C2 Spectroscopy On The Pulsed Ablation Of Graphite In The Visible Spectrum, Brandon A. Pierce
Cn And C2 Spectroscopy On The Pulsed Ablation Of Graphite In The Visible Spectrum, Brandon A. Pierce
Theses and Dissertations
An experimental study was conducted on the nanosecond pulsed laser ablation of graphite using a KrF laser at a fluence of 3.8 J/cm2 in Air, Ar, He, and N2. Optical emissions spectroscopy revealed the C2 Swan sequences and the CN Violet sequences. A spectroscopic model was developed to extract the molecular rotational and vibrational temperatures of each excited species for t=0.5-10 microseconds after laser irradiation. The rovibrational temperatures were found to vary with background gas for the CN Violet; however, only the vibrational temperature varied between He and the other background gases for C2 Swan. …
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Design, Development, And Testing Of A Low Cost, Additively-Manufactured, Centrifugal Compressor, Aaron P. Bauer
Theses and Dissertations
The three objectives of this research were to: 1.) design, build, and test AM compressors to substitute into COTS micro-gas turbine engines, 2.) provide initial correlations between FEA and compressor failure speed, and 3.) characterize the effects of AM on compressor performance. These goals improved the design cycle cost and the design-validation time cycle. ULTEM 9085, 300-AMB, and Onyx-Kevlar temperature-dependent tensile properties were measured. FEA-predicted failure speeds of stock compressor designs led design improvements, potentially fulfilling the original compressor requirements. Physical testing of the stock and ULTEM 9085 compressors occurred. Comparing these compressors' performances demonstrated that low cost, AM materials …
Modeling Hybrid Composites Using Tsai-Wu And Hashin Failure Criterion, Candice R. Roberts
Modeling Hybrid Composites Using Tsai-Wu And Hashin Failure Criterion, Candice R. Roberts
Theses and Dissertations
Hybrid composites require further study and testing for future use in various fields. This study focuses on simulating a Hybrid Composite using IM7-977-3 laminae with steel foils in Abaqus under bolt loading by using Hashin and Tsai-Wu failure criterion. Initial simulations contain only the IM7-977-3 composite with cohesive layers. Foil samples were then tested for accurate material properties from which the simulations were then updated to include steel foils. The two models show that Tsai-Wu failure criterion, while great for anisotropic material in tension, does not prove accuracy around the hole of the composite material which is in compression. Hashin …
Effect Of Surface Roughness On Ultrasonic Inspection Of Electron Beam Melting Ti‐6al‐4v, Evan T. Hanks, Anthony N. Palazotto, David Liu
Effect Of Surface Roughness On Ultrasonic Inspection Of Electron Beam Melting Ti‐6al‐4v, Evan T. Hanks, Anthony N. Palazotto, David Liu
Faculty Publications
Experimental research was conducted on the effects of surface roughness on ultrasonic non-destructive testing of electron beam melted (EBM) additively manufactured Ti-6Al-4V. Additive manufacturing (AM) is a developing technology with many potential benefits, but certain challenges posed by its use require further research before AM parts are viable for widespread use in the aviation industry. Possible applications of this new technology include aircraft battle damage repair (ABDR), small batch manufacturing to fill supply gaps and replacement for obsolete parts. This paper aims to assess the effectiveness of ultrasonic inspection in detecting manufactured flaws in EBM-manufactured Ti-6Al-4V. Additively manufactured EBM products …
Deep Donors And Acceptors In Β-Ga2O3 Crystals: Determination Of The Fe2+/3+ Level By A Noncontact Method, Christopher A. Lenyk, Trevor A . Gustafson, Larry E. Halliburton, Nancy C. Giles
Deep Donors And Acceptors In Β-Ga2O3 Crystals: Determination Of The Fe2+/3+ Level By A Noncontact Method, Christopher A. Lenyk, Trevor A . Gustafson, Larry E. Halliburton, Nancy C. Giles
Faculty Publications
Electron paramagnetic resonance (EPR), infrared absorption, and thermoluminescence (TL) are used to determine the Fe2+/3+ level in Fe-doped β-Ga2O3 crystals. With these noncontact spectroscopy methods, a value of 0.84 ± 0.05 eV below the conduction band is obtained for this level. Our results clearly establish that the E2 level observed in deep level transient spectroscopy (DLTS) experiments is due to the thermal release of electrons from Fe2+ ions. The crystals used in this investigation were grown by the Czochralski method and contained large concentrations of Fe acceptors and Ir donors, and trace amounts of Cr …
Mitigation Of Anisotropic Fatigue In Nickel Alloy 718 Manufactured Via Selective Laser Melting, Volodymyr P. Sabelkin, Gregory R. Cobb, Travis E. Shelton, Megan N. Hartsfield, David J. Newell, Ryan P. O'Hara, Ryan A. Kemnitz
Mitigation Of Anisotropic Fatigue In Nickel Alloy 718 Manufactured Via Selective Laser Melting, Volodymyr P. Sabelkin, Gregory R. Cobb, Travis E. Shelton, Megan N. Hartsfield, David J. Newell, Ryan P. O'Hara, Ryan A. Kemnitz
Faculty Publications
The tension-tension fatigue behavior of heat treated selective laser melted (SLM) nickel alloy 718 (IN718) tensile specimens was tested and compared to as-built specimens. In addition to the industry standard IN718 heat treatment, a modified heat treatment was developed and tested in order to mitigate the anisotropic mechanical properties inherent to SLM materials. Electron backscatter diffraction verified that the modified heat treatment significantly affected the microstructure in all build planes. Three different print orientations were studied to determine their effect on the fatigue behavior. Both heat treatments improved the fatigue life of the specimens, although neither surpassed the fatigue life …
Nonlinear Characterizing Of A New Titanium Nitride On Aluminum Oxide Metalens, Michael A. Cumming
Nonlinear Characterizing Of A New Titanium Nitride On Aluminum Oxide Metalens, Michael A. Cumming
Theses and Dissertations
A sample metalens generated from Titanium Nitride deposited onto Aluminum Oxide was designed to focus at 10 microns with a beam centered at 800nm, and when analyzed with high intensity illumination was found to have a focal length of 9.650 ±.003µm at an intensity of 16.93[MW/cm2 ]. Analyzing this change by comparing it to a Fresnel Lens’ physics shows that for this lens, the effective nonlinear index of refraction is certainly greater than the nonlinear index of just Titanium Nitride itself, at −1.6239 × 10−15[m2/W] compared to the materials −1.3 × 10−15[m2 …