Engineering Commons^™

Disintegration Of Green Missouri Fire Clay Bodies At Low Temperatures, Wilbur Brooks Schofield

Bachelors Theses

"Several years ago in the Ceramics Lab. of the Missouri School of Mines some A. P. Green Ozark Clay test pieces were left in a drier for a period of about seven months at a constant temperature of 110C. At the end of this period it was noticed that these specimens had disintegrated and crumpled down to a powdered mass. The object of this experiment was to repeat the former test and see if the clay would disintegrate and if so why. We also wished to find if by drying at higher temperatures for a shorter length of time would …

Size And Shape Of Clay Grains As Affected By Various Methods Of Grinding, Henry William Meyer

Bachelors Theses

"It is a common belief among those persons manufacturing dry pressed brick that the shape of grain of the clay used for this purpose would materially affect the physical properties of the resultant product. Some believe that clays, dry pan-ground, give a better product than clays disintegrated mechanically or passed through rolls. In some recent dry press investigations it was found that some milling methods gave an advantage over other methods, in the matter of pressure transmission. Due to this, a possible cause for the advantage was attributed to the shape of the grains resulting from the various methods of …

The Commercial Value Of High Iron And High Alkalie Diaspore, William Lucius Mccracken

Bachelors Theses

"In a recent survey of the refractory field particularly regarding high iron and high alkali diaspore it was suggested that perhaps some of these impure clays had the proper flux content to make them a body of stable volume in the initial firing operation. At present there is an apparant sic lack of information regarding the commercial value of these impure diaspores. One of the great problems in the use of diaspore refractories is the lack of stability of volume while in service subjected to severe heat treatments of varying degrees"--page 3.

The Transmission Of Pressure In The Dry Pressing Of Typical Building Brick And Fire Brick Mixes As Affected By The Variation In Grog Size, Henry Rickel Herron

Bachelors Theses

"In the formation of dry pressed ware, the transmission of pressure is of vital importance to the quality and character of the finished product as regards the resistance to spalling, load at high temperatures, slag action, abrasion and other physical properties. Furthermore, the transmission of pressure is a limiting factor as regards the size and irregularity of shape of a product manufactured by the dry press process"--Introduction, page 1.

The Transmission Of Pressure In The Dry Pressing Of Typical Building Brick And Fire Brick Mixes As Affected By The Variation In Grog Size, Stanley John Tompach

Bachelors Theses

"In the formation of dry pressed ware, the transmission of pressure is of vital importance to the quality and character of the finished product as regards the resistance to spalling, load at high temperatures, slag action, abrasion and other physical properties. Furthermore, the transmission of pressure is a limiting factor as regards the size and irregularity of shape of a product manufactured by the dry press process. Prior to the time of this investigation several companies have succeeded in producing ware up to six (6) inches in depth; but an increase over six inches has resulted, in every case, in …

The Effect Of Small Amounts Of Chrome Ore On Dry Press Diaspore Refractories, Allen John Reid

Bachelors Theses

"The term "Diaspore" as used in this paper will be used to mean the diaspore clay from which refractory bodies are made. The pure mineral Diaspore (Al₂O₃ . H₂O) has an Al₂O₃ content of 85%, while the best grades of diaspore clay run from 76% to 79% diaspore. Diaspore clay consists of a varying percentage of diaspore, ranging from 60% to 79%, and the remaining percentage as clay. The most objectionable impurities which occure sic in diaspore clay are alkalies. The chief source of diaspore is the central part of Missouri. It occurs in pot hole formations accompanied by "flint" …

Pressure Transmission In Clays Affected By Time Of Pressure Application, Robert Edward Lee

Bachelors Theses

"Experienced dry-press operators have long known that when they slow down their presses, to the proper speed they are able to exert more pressure on a wetter mix with out pressure cracks becoming apparent. When a clay mix is compressed in a dry-press there is a gradation of the pressure exerted, from the rams to the center, causing in some cases a soft centered brick. "Shelly brick", are undersirable sic because they do not have uniform physical properties through out. This weakens their structure, due to unequal stresses developed in drying and fireing sic. The defective structure of dry-pressed brick …

Test 186: Bates Steel Mule Model 35, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Some Early Geologists And Their Work In Montana, John E. Blixt

Bachelors Theses and Reports, 1928 - 1970

This paper marks an increased refinement and more detailed accuracy in the description of the geological features of the state. It includes the recent studies of mineral deposits, of oil structures, of the formations of bedded rocks and their included fossils, carried on both by the Federal and State governments and by various interested private persons, such as the mining companies. It is within this period that the Federal Government encouraged the U. S. Geological Survey in the publication of monographs on the National Parks, papers of great popular interest and educational value making these beautiful regions comprehensible in their …

Age Relationships Of Ore Deposits Of Southwestern Montana (A Microscopic Study), Charles R. Trueworthy

Bachelors Theses and Reports, 1928 - 1970

Although considerable work has been undertaken by some prominent geologists, the best known of which is that of Paul Billingsley and J. A. Grimes', in investigating the ore deposits of the Boulder Batholith and surrounding area, there has not been any complete microscopic investigation of these deposits, as a whole, published in the literature. With this in mind it was suggested to the writer by Professor Paul A. Schafer, of the Montana School of Mines, that a microscopic study of the ores of this region would be a worthwhile geologic problem.

It was thought that the mineral association and the …

A Preliminary Study Of The Separation Of The Copper Sulfides From Sphalerite And The Effect Of Certain Reagents On Some Of The Pure Copper Minerals In Synthetic Mixtures, Gailen T. Vandel

Bachelors Theses and Reports, 1928 - 1970

The problem of separating the copper sulfide minerals from sphalerite, in copper - zinc ores, has been a difficult one. This is largely due to the lack of adequate research and the small amount of data obtainable on the behavior of copper and zinc sulfide minerals in flotation circuits.

Discrepencies Of Theory As Against Empirical Results Of Critical Speeds Of Circular Cross Sectioned Shafting, Vern Kilpatrick

Electronic Theses and Dissertations

The scope of this thesis included computations and tests showing the first critical speeds of two shafts each 5/8" dia x 38" long one of C.R.S. and one of hard drawn brass. The purpose was to find and tabulate the discrepancies between the computed values for the critical speeds and the empirical values for critical needs.

Test 185: Rumely Model 6a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 187: Bates Steel Mule Model 45, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 193: Allis Chalmers Model Ek, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 196: Cletrac Model 15, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 194: Mccormick Deering Industrial Model 20, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 189: Allis-Chalmers "All Crop", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 190: John Deere Gp, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT: John Deere GP

TEST A: The manufacturer's representative operates the tractor for a minimum of 12 hours using light to heavy drawbar loads in each gear.

This serves as a period for limber up, general observation and adjustments. Adjustments that are permissible include valve tappet clearance, breaker ,point gap, spark plug gaps, clutch and others of a similar nature. No new parts or accessories can be installed without having mention made of it in the report. No data' are recorded during this preliminary run except the time that the engine is operated.

BELT HORSEPOWER TESTS

TEST …

Test 191: Massey-Harris "General Purpose", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 192: Bradley "General Purpose", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 197: Minneapolis- Moline Universal Model Mt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 198: Mccormick-Deering Farmall "F-30", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

Test 199: Mccormick-Deering "Tractractor", Nebraska Tractor Test Lab

Nebraska Tractor Tests

All tractors tested at the Nebraska Tractor Test Laboratory were certified by their manufacturers as being stock model machines, conforming to specifications filed with the application for test. No special or high-test fuels were used except as recommended by the manufacturer as necessary.

All results within the official tractor test report were actually attained in tests and are without correction or allowances for friction, temperature, altitude, etc. The results were initially accomplished with the tractor in charge of skilled operators employed by the University.

Unless otherwise noted, each tractor was apparently in good condition at the end of the testing …

A Qualitative Study Of Arsine And Stibine Reactivity Toward Inorganic Salts In Certain Solvents, John Edgar Antener

Masters Theses

"The effects of arsine and stibine on some substances have been investigated by various workers and recorded without any attempt at systematic classification. In this work a more comprehensive study of the precipitating effect of arsine and stibine on common inorganic salts in certain solvents, namely, water, ethyl alcohol, ethyl ether, acetone, carbon disulphide, carbon tetrachloride, chloroform, and benzene has been made, with an attempt at reactivity classification"--Introduction, page 1.

A Study Of Anode Corrosion And Its Influence On Cathode Purity In Electrolytic Zinc Production, Harold John Roesser

Masters Theses

"Anode corrosion is a problem with which electrolytic zinc producers have been concerned from the beginning of the practice. It has been attacked here from the view of modern practice, using alloyed anodes"--Introduction, page 1.

Flotation Of A Western Complex Ore, Guy Verdier Martin

Masters Theses

"The flotation of the complex sulphide ore, which is the subject of this investigation, has been in progress on a large scale for several years. As the operation has been successful it follows that the ore dressing methods have been developed in much detail. For further improvements an intense investigation is required. The complex nature of the ore opens many avenues of research along some of which clues may be found that will lead to ultimate savings. It is along a few of these avenues that this investigation has been directed. Hence an effort was made to add to the …

Comparison Of Results Obtained On Ores From The Tri-State Zinc-Lead District After Grinding To Different Sizes And Concentrating By Flotation, Hans Maucher

Masters Theses

"The purpose of this investigation is to compare the phenomena observed in concentrating a zinc ore by flotation, using a constant and new flowsheet as described a few pages later and varying only the sizes to which the headsamples are ground previous to each test"--Summary, page 1.

Wind And Earthquake Stresses In Tall Buildings, Henry A. Reynolds

University of the Pacific Theses and Dissertations

With the increasing cost of land in the modern city it has been necessary to expand upward rather than on the surface. The result has been to concentrate commercial and industrial enterprises in small areas whose influence is felt over the entire world. Notable examples are New York and Chicago. In these developments the engineer has played no small part. It is claimed by some that the maximum economic height has been reached at a thousand feet. However, both the Chrysler and Empire State Buildings have slightly passed this mark. It is not improbable that even taller buildings then these …

The Use Of A Small Electric Motor In Silo Filling, E. E. Brackett, E. B. Lewis

Nebraska Agricultural Experiment Station: Historical Circulars

Filling a silo 30 feet or more in height with a motor as small as five horsepower has been looked upon in general by Nebraska farmers as an impractical, if not impossible, procedure. The practice is not unheard of in other states, and certainly the possibility of avoiding the large tractor-driven cutters and the large crews will be welcomed by those who have available service from power lines.