Engineering Commons^™

The Irish Plumber And Heating Contractor, August 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

Analysis Of Radio Wave Propagation Over An Atmospheric Ground Layer By The Ray Tracing Method, Donnelly J. Johnson

Electrical and Computer Engineering ETDs

Previous efforts to analyze radio wave propagation in the troposphere have shown by agreement with experimental results the validity of the use of geometrical optics and the assumption of atmospheric spherical symmetry.

The Irish Plumber And Heating Contractor, July 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

Pavement Surveys, Milton Evans Jr.

Kentucky Transportation Center Research Report

The major considerations in the evaluation of a slab's condition, where surface defects exist, are the number of defects, their type and size. It is possible for a slab to contain a large number of surface intrusions without being appreciably damaged, if the impairments are all very small. On the other hand, only a few very large defects would be very damaging. Certainly, the most satisfactory condition would be the complete absence of blemishes.

In the surveys which have been made since the beginning of these pavement investigations, soil holes, chert pop-outs, shale pitting, trash imbedments and cracks have comprised …

Fugacity Coefficients Of Gases In Binary Mixtures, Louis David Mazzeii

Theses

A method of Pitzer for predicting component fugacity coefficients of gases in binary mixtures is evaluated by calculating 2100 fugacity coefficients and comparing the results to experimental data.

Pitzer employed the technique of Gamson and Watson in deriving an expression for fugacity coefficients. The expression is based on a three parameter corresponding states theory set of equations, and a definition of pseudo critical properties of mixtures, both previously proposed by Pitzer.

A further comparison with values calculated by similar methods of Edmister and Ruby, and Redlich et al (which previously were established as the most accurate general methods) indicates Pitzer's …

Thermodynamic Properties Of Hydrazine, Michael Perlswieg

Theses

The thermodynamic properties of hydrazine have been evaluated for the saturated region and for the superheated vapor. The superheated vapor properties were determined for temperatures up to 2200°F and pressures to 3000 psia. Enthalpy, entropy, and specific volume are reported for the saturated vapor and liquid and the superheated vapor. Results are reported in the form of tables.

Enthalpy values are relative to the saturated liquid at 32°F. Entropy values are absolute. The thermodynamic properties have been based on experimental data where possible. Due to the lack of experimental pressure-volume-temperature data, however, the generalized correlations of Lydersen, Greenkorn, and Hougen …

The Kinetics Of Hydrogen Reduction Of Chromic Oxide, Kurt Strater

Theses

The hydrogen reduction of Cr₂O₃ to chromium metal was found to be feasible at very low water vapor concentrations, approximately -38° to -24°C, over a temperature range of 1130° to 1490°C. Hydrogen reduction under these conditions was predicted by the calculated equilibrium curves which also indicated that Cr₂O₃ is reduced directly to chromium without forming the intermediate oxide, CrO. This reduction path was confirmed by X-ray diffraction analysis.

The percent reduction of Cr₂O₃ at each reaction temperature was constant with time suggesting an inhibiting effect of the gaseous reaction product, water …

Viscosity Correlations Of Saturated Fatty Acids And Their Esters, Thomas Joseph Redling

Theses

Several correlations have been developed which permit calculation of the viscosities of the n-paraffin fatty acids and esters, beginning with formic and including stearic acid.

The correlations were obtained by interrelating the Log u and the Log P_v at the same temperature, where u is the viscosity in centipoise and P_v is the vapor pressure in millimeters Hg. A single line relationship represents all the fatty acids from propionic acid to and including stearic acid, while formic acid and acetic acid each have their own line. Methyl, ethyl, propyl and butyl formate can be represented by a single …

The Effect Of Velocity On The Electrical Conductivity Of Blood, Judea Pearl

Theses

Although the change in the conductance of blood resulting from changes in its velocity has been noted by several investigators working with electrical impedance techniques, this parameter of measurement has heretofore not been investigated from the viewpoint of practical application to blood flow measurement.

In certain regions of the body such as the tooth pulp and the cranial cavity, the volume of the contained blood cannot fluctuate during a cardiac cycle because of the rigid wall of the chamber. Therefore, impedance pulses which have been obtained in studies on the tooth pulp, must be attributed to the rhythmical fluctuation of …

Physical And Electrical Properties Of The Manganin-Type Alloys, Wallace William Macintosh

Theses

This thesis is a report on the physical and electrical properties of the manganin-type alloys as compiled from the published literature on the subject. The peculiarities of these alloys, as related to mechanical history, heat treatment, and composition, are discussed. Empirical formulae, by which the temperature coefficient of resistance, the temperature of maximum resistance, the temperature-resistance equation, and the thermoelectric emf of these alloys against copper may be calculated, are shown.

A comparison of the effect of elongation on the specific resistivity of several sizes of manganin wire is made on the basis of experimental results. The effect of impurities …

The Electrolytic Preparation Of Perbromates, Robert M. Casciano

Theses

Since perchlorates and periodates can be formed by the electrolytic oxidation of chlorate and iodate solutions and since bromine lies between chlorine and iodine in the periodic table, it should be possible to electrolytically prepare perbromates. As yet, however, perbromates have not been prepared by any methods.

It was desired to attempt to prepare perbromates electrolytically and to definitely show their presence or absence after electrolysis. In order to accomplish this a new method of analysis was developed.

This work has shown that perbromates cannot be prepared by the electrolytic oxidation of bromate solutions under various conditions of temperature, current …

Effect Of Elevated Temperature On Efficiency Of Corrosion Inhibitors, Walter Dzingala

Theses

An experimental program was set up to investigate the effect of temperature on the protection efficiency of various inhibitors of metal corrosion. Contrary to most studies, an appreciable amount of the work was done with the corrosive effect being determined on the metal specimens that were exposed first to the inhibitor, then to air at different temperature, and finally to the corrosive medium with no inhibitor present. The purpose being to determine whether the inhibitor treatment would provide a permanent protection for a metal surface or would it be necessary to furnish a continuous supply of the inhibitor to the …

Extrapolation Of Viscosity Data For Liquids, Julius Irwin Gnapp

Theses

The method of finite-difference recurrence relations* is here applied to viscosity-temperature data to determine whether it offers an improved means of extrapolating such data. The best of the existing parametric correlations, which is considered to be that of Andrade, was found to be subject to important departures from linearity and dependent upon the particular data points used in its formulation. The proposed method is non-parametric in that it does not require an assumption of the explicit function relating viscosity with temperature. Instead, it assumes that there is a linear relation between successive values of viscosity at equal intervals of temperature. …

Catalytic Activity Studies In Aromatic Sulfonation, William Marvin Jayne Jr.

Theses

The object of this investigation has been to determine the catalytic activity of several inorganic materials in promoting the sulfonation of aromatic organic compounds. Initial work involved sulfonation of p-nitroaniline with an excess of sulfuric acid. However, due to insufficient precision of the method of analysis, this system was abandoned. Thereafter, the study was concerned chiefly with the benzene and other aromatic compounds in nitrobenzene solution. This phase of the work proved to be successful, and the results are reported in the text of the thesis.

The author gratefully acknowledges the suggestions and counsel given throughout these investigations by Professor …

A Simplified Procedure For Diffusion Coefficients From Cation Exchange Studies, Robert Peter Lanyon

Theses

The purpose of this investigation was to extend the data and to improve the procedures of previous investigators (1), (2), and (3), in the study of diffusion coefficients in aqueous media.

The main contribution of this investigation is the elimination of the tedious work of size grading, drying, weighing, and rehumidification of the Dowex 50 W - X8 resin, which is used to determine the ion exchange rates for the cations under consideration, The simplified procedure measures the resin volume by displacing a known volume of water. The method of calculating diffusion coefficients follows the procedure of (1), (2), (3), …

Binary Vapor Liquid Equilibria Isobaric Systems, Ira Lichtenstein

Theses

Oalculations of activity coefficients for thirty isobaric binary systems from vapor-liquid equilibria data were made using the Gilmont equation© An extensive literature survey showed the Gilmont equation provides an excellent means of correlating equilibrium data in most binary isothermal systems° However, the Gilmont equation’s applicability to isobaric systems had not been satisfactorily proven, and became the object of this investigation.

The Gilmont equation gave satisfactory correlation of the binary isobaric data for various systems. The correlation was found to improve as the systems approached ideal behavior. The introduction of a temperature correction to the relative volatility, term improved the correlation …

Hydraulic Characteristics Of Showerdeck Trays, Sam Gordon Marx

Theses

The hydraulic operating characteristics of the showerdeck tray were investigated. Air-water studies were made using a four plate, 11 1/4 inch I. D. plexiglas column.

Entrainment, liquid froth height, and pressure drop data were obtained at varying liquid and vapor rates.

Entrainment was found to be a function of the plate spacing, liquid height on the tray, the liquid rate and the column vapor velocity. It was found to be independent of the vapor velocity through the perforations. An equation of entrainment as a function of these variables was derived.

The liquid froth height on a tray was found to …

Electrolytic Amalgam Reduction Of Cinnamic Acid, Alan Ira Mytelka

Theses

The use of sodium amalgam and potassium amalgam to reduce cinnamic acid to hydrocinnamic acid was accomplished in two concentrically constructed cylindrical cells.

In the outer cell, liquid amalgam was prepared electrolytically using a mercury cathode. The amalgam was moved by a rocking motion into the inner cell where the cinnamic acid dissolved in ethanol was reduced to hydrocinnamic acid. The actual percent conversion as measured by iodine numbers varied from 6.0% to 567, the percentage depending upon the number of coulombs passed into the electrolytic cell, the amalgam used, and whether or not stirring in the inner reduction cell …

The Electrolytic Oxidation Of Para-Nitrotoluene, Mustafa Darwish Shamy

Theses

The factors affecting the electrolytic oxidation of p-nitrotoluene to p-nitrobenzoic acid have been studied, and optimum conditions determined for obtaining the best overall yield of 65.7 per cent. These Anode:lead sheetCathode:lead sheetAnolyte:250 cc of 50 per cent sulfuric acid
10 grams of p-nitrotoluene
5 grams of chromic trioxideCatholyte:250 cc of 50 per cent sulfuric acidVoltage:4.5 ± .5 voltsCurrent density:3.0 amperes per square decimeter.Temperatures65 ± 3°CReaction time:fifty per cent of the theoretical time required

It was observed that high potentials and prolonged reaction periods are detrimental to the yield.

A mechanism for the electrolytic oxidation process is suggested, based on experimental …

Surface Area Of Small Particles, Richard Henry Ullrich

Theses

Experiments using glass beads and water were performed to obtain data to relate evaporation rates with the total surface area of a small sample of particles. The object of this work was to explore the possibility of devising a new method of determining surface areas which would be simple, rapid and non-destructive.

One gram samples of glaze beads ranging in diameter from 840 to 150 microns were wet with water and dryed to constant weight under controlled conditions. Residual water was removed by continued heating at a higher temperature. The experimental conditions were deliberately simple in keeping with the purpose …

Attrition In A Fluidized Bed, Andrew Joseph Welter

Theses

The object of this thesis is to study attrition in a fluidized bed in an attempt to find a reliable method for predicting attrition rate when fluid flow rates and particle sizes are varied.

The system studied consisted of air as the fluidizing median with bauxite and fuller's earth as the solids in suspension. Fluid flow rates were changed while all other variables were held constant. Systems with both large and small particles were studied for each material.

It was found that the attrition rate of the material when the bed is maintained at a constant mass flow rate is …

Investigation Of The Stability And Response Of A Reboiler Under Condensate Control, Francis Arthur Winter

Theses

Control of heat flux by condensate throttling was investigated theoretically by frequency response analysis and experimentally on a simulated reboiler control system.

Transfer functions were derived for each component and ware used to describe the response of the experi- mental system. Experimental controller settings were in reasonable agreement with the calculated results. However, general overall control was poor because of dead time and cyclic disturbances. Experiments showed that the process contained dead time in the order of three to seven times the ultimate period (0.5 - 1.0 minutes). Several sources of disturbances prevented an accurate evaluation of stability at low …

Test 799: John Deere 2010 Ru Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 798: John Deere 1010 C Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Evaluation Of The Thermal Properties Of Plastic Laminates, Luciano Sedillo

Chemical and Biological Engineering ETDs

To insure the proper application of newly developed materials, it is necessary to evaluate their physical and chemical properties. In the case of plastic laminates for use as heat barrier material, thermal diffusivity is an important property. Thermal diffusivity is the parameter which governs the rate of temperature change through a material. Its value depends upon the chemical composition and the physical structure of the material and its temperature.

Cerenkov Radiation From An Electron Traveling In A Circle Through A Dielectric Medium, John Joseph Newman

Optical Science and Engineering ETDs

Two hardware configurations are discussed which might be used as vehicles for checking the accuracy of the theory. It is hoped that one of these configurations might lead to a device which would yield a useful amount of power in the submillimeter region of the microwave spectrum.

The Irish Plumber And Heating Contractor, June 1961 (Complete Issue)

Building Services Engineering

No abstract provided.

An Experimental Study Of The Production Of Metallic Impregnations And Coatings -- A Vacuum Process, Engle D. Southard

Chemical and Biological Engineering ETDs

The purpose of this study undertaken was threefold, (1) to design and construct an experimental vacuum apparatus to produce a metal impregnated or coated material; (2) to study some of the variables which affect the process; then (3) to examine the physical characteristics of the resultant materials. Described herein is the development and operation of a vacuum system capable of producing conditions to permit the evaporation of metals to impregnate and coat various materials. The fundamental principle involved in this process is that a rarified atmosphere reduces the temperature required for metal evaporation and protects the metal vapor from reacting …

Comparison Of Pulse And Fm Radar Altimeters Based On Terrain Return Theory, David L. Quinlan

Electrical and Computer Engineering ETDs

In this paper a comparison of pulse of fm radar altimeters is made from the standpoint of the mathematical expressions describing each system’s return signal from terrain at near-vertical incidence. The pulse-fm radar relationships resulting from this comparison facilitates application of the extensive information gained in previous pulse radar studies to the investigation of fm radar terrain return and the associated design of fm radar altimeters, and may also assist in the development of the new pulse-type radars.

Effect Of Cleaning Methods Upon Electrochemical Behavior Of High-Carbon Steel Cathodes In A Chromic Acid Electrolyte, George Chaplenko

Theses

The quality of electrodeposited coatings is to a great ex- tent determined by cleaning or surface-conditioning methods employed in preparing the basis metal for plating. Cleaning pro- cedures are usually established empirically, by trial and error. Little or no experimental work was devoted to a quantitative stu- dy of measurable parameters that are influenced by the relative effectiveness of individual cleaning processes. The present ex- periment was designed in an attempt to establish a correlation between one such parameter (namely, the single-electrode poten- tial of polarized cathode) and the quality of subsequent plating.

High-carbon steel cathodes, -a material that is …