Engineering Commons^™

A Computer Simulation Of A Partial Venous System Of A Human Lower Extremity, David C. Smith

Theses and Dissertations

The human body is truly a fascinating and complex creation of our Maker. Because of the complexity and variability, many of its workings were little known until recent years. Some of the more amazing facts of the circulatory system follow. If the individual blood vessels of a single adult, i.e., artery, arteriole capillary, venule and vein, were laid end to end, they would extend more than 60,000 miles. For the average adult, the heart beats 70 times per minute; for the well-conditioned athlete, 50-60 beats per minute; and for the extraordinary athlete, as few as 37 times per minute. The …

Transient Convective Heat Transfer Coefficient For Injection Into Rigid Vessel, James Edward Steiger

Theses and Dissertations

The purpose of this study was to develop and demonstrate a method for experimentally determining the convective heat transfer in a rigid vessel while air was being injected. The heat transfer took place between the air in the pressurized vessel and the surrounding walls which were maintained at a temperature of 32 F. with a circulating ice water bath. The study considers the effects of injection geometry and injection flow rate on the heat transfer process. The problem of heat transfer after injection has been considered by Means (1), and was responsible for establishing this study. The experimental technique used …

Hydraulics Of Waste Stabilization Ponds And Its Influence On Treatment Efficiency, Kenneth A. Mangelson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The treatment efficiency of waste stabilization ponds depends on many factors, the most important of which are generally presumed to be the biological factors such as the type of waste and the organic loading. However, the biological activity in a pond is greatly influenced by the environmental conditions of temperature, wind, sunlight, and the hydraulic flow patterns. In the past little attention has been given to the hydraulic characteristics of waste stabilization ponds. Specifically, little consideration has been given to the gross flow patterns within stabilization ponds as affected by the shape of the pond or lagoon, the presence of …

A Comparison Of Technologist Needs And Training Requirements Of The Major Industries Within The State Of Utah, Gene E. Forsberg

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The technologist needs and training requirements were determined from a selected cross-section of Utah industrial firms.

The larger industries were significantly more aware of the training requirements and capabilities of four-year technologists than were the smaller firms.

A significant difference was found regarding general and specialized training required by each firm. Thirteen of the 16 responding firms indicated specialized training as being most important.

The 10 areas of technical training rated most critical in their order of importance were: electronics, technical writing, electricity, English, mathematics (calculus and above), machine shop, manufacturing processes, physics, and metallurgy and design.

There was no …

Hydrologic Inventory Of The Great Salt Lake Desert Area, Gary L. Foote

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Utah, located in the arid southwest, is a state that experience s chronic water shortages. The pattern of valleys and high mountain ranges that exists in the state produces sharply contrasting differences in climatic conditions . Desert valleys in the western portion may receive as few a s 4 inches of precipitation in a year while headwater areas in the Wasatch Mountains receive 60 inches or more. Wide cyclic as well a s geographical variations of precipitation added to uneven seasonal distribution makes development and efficient utilization of water resource s vital though difficult.

In order to make the most …

Phosphorus Distribution In The Bottom Sediments Of Hyrum Reservoir, Kirk L. Schmalz

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The distribution of phosphorus in the sediment of Hyrum Reservoir was studied by collecting and analyzing 84 sediment samples for total, inorganic, organic, and water-soluble phosphorus.

Sample locations were mapped by triangulation and sediment phosphorus distribution maps were made. Sediment analysis showed average total phosphorus content of 755 micrograms per gram, with organic phosphorus composing approximately 97 percent of total phosphorus.

Sediment samples showed variability in phosphorus content which precluded identification of point sources of phosphorus input to the reservoir. Several areas of comparatively higher phosphorus content in the sediments were shown with isopleth maps.

An estimate of the extent …

Conduction Error In Thermocouples Embedded In Low Conductivity Material, Tumkur G. Nagaraju

Theses and Dissertations

Thermocouples are generally used as devices to determine the internal temperature of any material. The purpose of the temperature measuring device is to measure the temperature which would exist at some known location if the device were not present. The thermocouples are embedded in the material in order to study the temperature-time history of the point of location. The presence of the thermocouple induces error in the temperature measured. This error becomes significant if heat is conducted into or away from the point of measurement by the sensor itself, or if the sensor insulates the point. This would result from …

A Statistical Theory Of Avalanche Breakdown In Silicon, Terence Vincent Sewards

Electrical and Computer Engineering ETDs

A statistical theory of avalanche breakdown in silicon is presented, based on the conventional Boltzmann transport equation. The scattering mechanisms considered are impact ionization (electron-hole pair production), phonon emission and absorption, thermal generation and recombination. The resultant critical field is found to depend on the recombination statistics, which were ignored in previous theories of avalanche breakdown. The theoretical temperature dependence is compared with the temperature dependence of the breakdown voltages of three conunercial diodes.

Development Of An Electronic Means Of Weighing Vehicles In Motion, Ben W. Carr Jr., Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

An in-stream weighing platform was designed and installed in the eastbound lane of I 64 and 75 near Lexington, Kentucky. The broken-bridge scale platform was designed with the outer edges of the two sections supported on hinges and contiguous edges supported by two 20,000-pound capacity load cells. The assembled scale measures 4'-6" x 10'-1/2" with a total weight of about 2,000 pounds.

The electronics developed for the system included digitizing circuitry which processed the load cell signals and recorded the data on digital magnetic tape. Computer processing of the field data produced tabular information on vehicle speed, axle spacing, number …

Experimental Concrete Pavement Containing Fly-Ash Admixtures [1971], James R. Philpot

Kentucky Transportation Center Research Report

The report enclosed is somewhat routine inasmuch as it documents a repeat of a portion of an earlier experimental project. The previous project was on Poplar Level Road; our final report was dated July 1966 (KYHPR-64-1). Special Provision No. 70 was used also on the Jefferson Freeway project. However, there was no "control section" involved in the current project. The Jefferson Freeway project was authorized by the BPR under P.P.M. 60-2 only (now PPM 20-6.3).

The most significant findings from both projects concern the water requirements the concrete containing the fly-ash admixture. Whereas laboratory tests indicated reasonable expectations of a …

An Experimental Investigation Of The Vortex Sink Rate Sensors, Nelson L. Lu

Mechanical & Aerospace Engineering Theses & Dissertations

The vortex sink rate sensor device consists basically of an ideal sink flow between two coaxial disks. A sink tube was located at the center of one disk. The vortex was created by the rotation of the unit about its axis of symmetry. Five inch and 10 inch diameter of porous couplers were used for the air chamber here in this investigation. Several slenderness parameters, i.e., the ratio of the sink tube diameter to the height of the air chamber ^ro/n were conducted. Two probes were used to measure the static pressure and stagnation pressure respectively at various positions …

A Theoretical And Experimental Study Of An Unsteady Pressure Measuring System, Ramesh R. Batki

Mechanical & Aerospace Engineering Theses & Dissertations

Experiments were performed to determine the frequency response of gas filled instrument tubes, and the results were correlated with a theoretical model. The theoretical model developed by Bergh and Tijdeman for a series connection of thin circular tubes and volumes was studied in full detail and employed. A measuring system was designed and built to measure pressure ratio and phase lag employing thin nylon or vinyl tubes and strain gage transducers. 1'leasurements were performed using cathode ray tube, strip chart, analog techniques and also a commercial electronic function analyzer and the various results were compared. The theoretical and experimental influence …

Transverse Vibration Of A Class Of Orthotropic Plates, Nicholas J. De Capua

Dissertations

This study determines the eigenvalues, eigenvectors, and nodal patterns of a class of orthotropic plates whose geometry is governed by the equation

(x/a)^α + (y/b)^β = 1,

where the parameters a, b, a, and a permit the plate geometry to vary over a range which includes the rhombus, circle, ellipse, square, and rectangle.

Variable thickness, inplane forces, and mixed or discontinuous boundary conditions are also considered. The following assumptions have been employed:

i). plate is thin with respect to other dimensions,

ii). deflections are small,

iii). rotary inertia and shear are neglected.

The method of analysis employed is …

A Theoretical And Experimental Study Of The Mechanism Of Axoplasmic Convection In Nerve Fibers Driven By Peristaltic Surface Waves, Robert John Biondi

Dissertations

In the study of cell biology, investigators have found that substances which are produced within the cell nucleus are sometimes found throughout the cell at points distant from the site of production. In the case of nerve cells (neurons), this is particularly dramatic because of the unusual elongated geometry of these cells.

A neuron possesses a cylindrical tubular extension called an "axon" or "axis cylinder" which is characterized by a large length-to-diameter ratio (10³-10⁶). The existence of a continuous proximo-distal flow of axoplasm within these cylindrical axons has now been demonstrated by numerous investigators. In …

The Development And Use Of Scattering Parameters For Semiconductor Junction Devices, Lee Dennis Philipp

Electrical and Computer Engineering ETDs

Scattering parameters are developed for diodes and tran­sistors. The parameters are developed through a modification of the wave equation from quantum mechanics. The effects of pulsed X-ray radiation on these devices is then calculated with the use of these parameters.

Various methods of analyzing semiconductor junction de­vices are discussed. These methods include diffusion theory, invariant imbedding and quantum mechanics. The background in these areas necessary for a discussion of semiconductor models is outlined.

Models resulting from the three basic approaches are presented. These include the Ebers-Moll Model, the Charge Control Model, the Linville Model, the Gore Model, the MLB (McKelvey, …

Ole Miss Engineer 1971

Ole Miss Engineer

No abstract provided.

How About A System?, Tim Brady

Publications

A checklist for air safety is discussed. A lengthy process, but necessary for air safety.

Static And Dynamic Buckling Of Shallow Arches, David D. Loendorf

Civil & Environmental Engineering Theses & Dissertations

The static and dynamic buckling behaviors of a shallow, simply supported sinusoidal arch subjected to both a uniformly distributed step pressure load and a purely impulsive load are considered. Five equilibrium paths are obtained for the arch under static loading conditions. Critical static loads corresponding to two different instability modes and based on characteristics in the load displacement curve are obtained numerically. Critical dynamic loads, corresponding to three different instability modes, are obtained from a numerical procedure in which buckling criteria are based on characteristics in the time response of the structure. The influence of damping on the various dynamic …

Parameter For Comparing Anemometer Response, L. M. Fingerson

Symposia on Turbulence in Liquids

In comparing the theoretical performance of sensors, the term e_b/q (voltage change due to change In heat transfer) was found to be a fundamental sensor parameter. This was true for both sensitivity and frequency response in both constant current and constant temperature systems. Equations and data are presented for calculating this parameter for most wire and film sensors. Wedges, cones, and other non-cylindrical sensors have not been included because of their special problems at low frequencies due to conduction losses.

Internal cooling of the sensor is used for high temperature environments. Calculations show that the sensitivity at low …

An Attempt To Characterize The ‘Turbulence Burst Phenomena’ Using Digital Time Series Analysis, B. Johnson, R. Saylor

Symposia on Turbulence in Liquids

Several attempts to measure "periodicity" in the output signal of hot wires and hot films located in the viscous sublayer have been made in recent years. The usual method is to perform an autocorrelation on the signal and to interpret the strong peaks in the correlation function as indicative of the mean period of the "turbulence bursts" during a particular sampling interval.

The data analyzed for the presence of "turbulent bursts" were from the test of a 60-foot, 8-oared racing shell at the David Taylor Model Basin of the Naval Ship Research and Development Center. The shell was instrumented with …

On The Phenomenon Of Vortex Street Breakdown, William W. Durgin, Sture K.F. Karlsson

Office of the Provost Scholarship

A von Kármán vortex street generated in the usual way was subjected to a deceleration, thereby changing the ratio of longitudinal to lateral spacing between the vortices. Distortion of the individual vortices followed which resulted in annihilation of concentrated vortex regions and creation of a stationary wake flow. This wake flow was itself dynamically unstable and developed into a new vortex street of a different frequency from the initial one. The breakdown of the initial vortex street is qualitatively explained by considering the convection of a concentrated vortex region due to the motion imposed by all the other vortices.

Ole Miss Engineer 1971

Ole Miss Engineer

No abstract provided.

The Analysis And Behavior Of Thin-Steel Hyperbolic Paraboloid Shells, Peter Gergely, P. V. Banavalkar, J. E. Parker

CCFSS Library (1939 - present)

An extensive experimental and analytical investigation of thin-steel hyperbolic paraboloid (hypar) structures was carried out to provide design information. As a result of this work, empirical data is provided regarding the behavior of such structures and computer programs are presented for the analysis of thin steel hypar structures. Hyperbolic paraboloid structures possess a unique combination of structural and architectural properties, some of them are the following 1) Due to the double curvature of the surface the internal stresses in the deck are generally low and the deflections are small. 2) Since a hyper surface can be generated by straight lines, …

Column Research Council: Proceedings 1971, Column Research Council

CCFSS Library (1939 - present)

One of the purposes of the Council is to maintain a forum where problems related to the design and behavior of columns and other compression elements in metal structures can be presented for evaluation and discussion. The Annual Technical Session provides opportunity to carry out this function. The 1971 Annual Technical Session was held on May 25 and 26 at the Pick-Rosseve1t Hotel in Pittsburgh, Pennsylvania. Seventy-seven persons attended the Session and twenty-two papers were delivered. A panel discussion on "Fire Effects on Structural Stability" was held in the evening of May 25. In conjunction with the Technical Session, an …

Damping Capacity Of A Model Steel Structure, Dixon Rea, R. W. Clough, Jack G. Bouwkamp

CCFSS Library (1939 - present)

The damping capacities of seven model steel structures, each consisting of a heavy steel platform supported on four columns, have been determined from forced vibration tests. The vibrations were produced by an eccentric-mass vibration generator, and the amplitudes ranged from small displacements up to slightly greater than yield displacement. The tests were terminated at the higher amplitudes once fatigue cracks formed in any of the joint welds in the columns. For vibration amplitudes up to a critical amplitude slightly less than yield displacement, the damping factors of the structures were constant, independent of amplitude, and ranged between .15 and .25~ …

Analysis Of Light Gage Steel Shear Diaphragms, Albert R. Ammar, Arthur H. Nilson

CCFSS Library (1939 - present)

INTRODUCTION: It has long been recognized by structural engineers, that light gage steel cladding floor and roof decking systems have a considerable stiffening and strengthening effect on building frameworks. The beneficial contribution of these diaphragm systems is most pronounced when the structure as a whole is subjected to loads which result in an in-plane shear action of the cladding. This occurs, for example, when the rigidity of a floor or roof diaphragm acting as a membrane is utilized to transmit lateral forces to stiff end walls. Another example of diaphragm action is found in pitched roof portal sheds under vertical …

Analysis Of Light Gage Steel Shear Diaphragms, Albert R. Ammar, Arthur H. Nilson

CCFSS Library (1939 - present)

INTRODUCTION It has long been recognized by structural engineers, that light gage steel cladding floor and roof decking systems have a considerable stiffening and strengthening effect on building frameworks. The beneficial contribution of these diaphragm systems is most pronounced when the structure as a whole is subjected to loads which result in an in-plane shear action of the cladding. This occurs, for example, when the rigidity of a floor or roof diaphragm acting as a membrane is utilized to transmit lateral forces to stiff end walls. Another example of diaphragm action is found in pitched roof portal sheds under vertical …

Analysis Of Light Gage Steel Shear Diaphragms, Arthur H. Nilson

CCFSS Library (1939 - present)

A method is presented for the elastic analysis of shear diaphragms composed of standard light gage steel panels. A finite element approach is adopted, in which the mechanical properties of the diaphragm components are incorporated in an analytical model of the assemblage, using the direct stiffness method of matrix structural analysis. Results are compared against experimental values.

Conference Proceedings Of The Symposium On Turbulence In Liquids October 4-6, 1971, University Of Missouri--Rolla

Symposia on Turbulence in Liquids

No abstract provided.

Fisheries Report No Viii (8) - Report On A Visit Of Inspection To Barrow Island November 1969, A. A. Burbidge, A. R. Main

Fisheries Research Reports

The aim of the inspection was to examine the effects on the fauna and flora of the oil exploration initiated in mid-1963 by West Australian Petroleum Pty. Ltd. (WAPET) and the construction and development programme which followed in 1966 and which is now nearing completion.