Engineering Commons^™

Liquid-Vapor Distributions In Evacuated Small Diameter Channels For Improved Accuracy Of Initial Conditions In Modeling Of Oscillating Heat Pipes, Travis Mayberry

Mechanical Engineering Research Theses and Dissertations

Oscillating heat pipes, also known as pulsating heat pipes, are increasingly becoming a preferred high-performance thermal ground plane in a variety of heat spreading applications due to a number of advantages over traditional copper-water wicked heat pipes, including their lighter weight, thinner profiles, simpler fabrication, and greater variety of material and working fluid options. A major barrier to even wider adoption, however, is the lack of comprehensive analytical models to simulate their performance. A key input to first principles models simulating the fundamental physics of the devices is the initial condition of liquid and vapor segment lengths and their distribution …

High-Order Deterministic Sensitivity Analysis And Uncertainty Quantification: Review And New Developments, Dan Gabriel Cacuci

Faculty Publications

This work reviews the state-of-the-art methodologies for the deterministic sensitivity analysis of nonlinear systems and deterministic quantification of uncertainties induced in model responses by uncertainties in the model parameters. The need for computing high-order sensitivities is underscored by presenting an analytically solvable model of neutron scattering in a hydrogenous medium, for which all of the response’s relative sensitivities have the same absolute value of unity. It is shown that the wider the distribution of model parameters, the higher the order of sensitivities needed to achieve a desired level of accuracy in representing the response and in computing the response’s expectation, …

Coupled Flexural‐Electrical Evaluation Of Additively Manufactured Multifunctional Composites At Ambient Temperature, Ritesh Ghimire, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multifunctional composites offer a higher strength to weight ratio, electrical properties, etc., thereby providing possible solutions for replacing the physical electrical wirings in aircraft. The lack of research on the coupled multifunctional characterization of 3D printed composites flexural-electrical properties is the main reason for its unsuitability in aerospace applications. The proposed method evaluates multifunctional flexural‐electrical properties of 3D printed multifunctional carbon fiber composites. Traditional methods for conducting structural and electrical analyses for aircraft certification do not accommodate new technologies that are not yet proven. Such technologies are additive manufacturing (AM) techniques, multifunctional composite structures, and the certification requirements for 3D …

Assessing The Feasibility Of A Belt Based Continuously Varied Transmission For Bicycles, Ethan Wicko

Holster Scholar Projects

The objective of this project is to establish the feasibility of a new drivetrain that decreases maintenance and decreases rider effort compared to current widely used derailleur-based drivetrains by utilizing a belt based continuously varied transmission. With further development, this technology will make cycling more accessible by reducing the mechanical knowledge required to maintain a functional bike and facilitate bicycle riding by increasing durability and providing infinite gear ratios within that range, potentially increasing the health and quality of life for many.

Dynamic Modeling Of Soft Robotic Dielectric Elastomer Actuator, Abdullah De Jesus El Atrache Ceballos

Doctoral Dissertations and Master's Theses

Dielectric elastomers actuators (DEAs) are among the preferred materials for developing lightweight, high compliance and energy efficient driven mechanisms for soft robots. Simple DEAs consist mostly of a homogeneous elastomeric materials that transduce electrical energy into mechanical deformation by means of electrostatic attraction forces from coated electrodes. Furthermore, stacking multiple single DEAs can escalate the total mechanical displacement performed by the actuator, such is the case of multilayer DEAs. The presented research proposes a model for the dynamical characterization of multilayer DEAs in the mechanical and electrical domain. The analytical model is derived by using free body diagrams and lumped …

Me-Em 2020-21 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Responsive Research
• Alumni Impact
• Innovative Enterprises
• Enrollment & Degrees
• Graduates
• Department
• Donors
• Contracts & Grants
• Patents & Publications

Occurrence And Probabilistic Health Risk Assessment (Pra) Of Dissolved Metals In Surface Water Sources In Southern Peru, Alexander Ccanccapa-Cartagena, Betty Paredes, Corina Vera, Francisco D. Chavez-Gonzales, Elizabeth Joy Olson, Lisa Welp, Nadezhda N. Zyaykina, Timothy R. Filley, David M. Warsinger, Chad T. Jafvert

School of Mechanical Engineering Faculty Publications

Often, metal and metalloid ions are present in water at concentrations that seriously affect human health; understanding their occurrence is critical, especially in regions such as Peru, where natural volcanic activity and anthropogenic activity have made them more prevalent in local waterbodies. In this study, river, lake, aquifer, and irrigation water samples, collected from the Chili-Quilca, Camana-Majes, Colca-Chivay-Siguas, Oco˜na, Urubamba-Vilcanota, and Titicaca river basins in Southern Peru, were analyzed for transition metals, other metals, metalloids, and other inorganic water constituents. Special emphasis was placed on metals and metalloids regulated by Peruvian Water Quality Standards and those categorized as of “primary …

Nanofluids Improve Energy Efficiency Of Membrane Distillation, Harsharaj B. Parmar, Hamid Fattahi Juybari, Yashwant S. Yogi, Sina Nejati, Ryan M. Jacob, Prashant S. Menon, David M. Warsinger

School of Mechanical Engineering Faculty Publications

Thermal desalination of high salinity water resources is crucial for increasing freshwater supply, but efficiency enhancements are badly needed. Nanomaterial enhancements offer enormous potential for improving promising technologies like membrane distillation (MD). However, while many approaches have been tried, such as nanoparticle solar absorbers or nanomaterial membranes, there have not been studies to directly enhance the fluid properties in MD; via nanofluids. In this work, we examine nanofluids for gap-based MD systems, including the role of nanoscale physics and system-level energy efficiency enhancements. Our model includes the dominant micro-mixing from Brownian motion in fine particle nanofluids (copper oxide) and the …

Mems 411: Free Kick Robot, Rahi Miraftab-Salo, Will Goldberg, Wlodie Rebesque

Mechanical Engineering Design Project Class

The free kick robot was designed to help train the club soccer goalkeeper: Brady Shaeffer, to save shots on goal. After a customer interview with the our client, we aimed our design to shoot accurate and powerful shots in quick succession. In addition the robot was to be easily transportable. Initially, after looking at some patents, the most commercially used soccer training robots involved two parallel disks spinning and shooting out soccer balls. As a result an initial prototype was built with this idea. However, during our concept selection, we realized that the cost of building our machine was out …

Mems 411: Safely Capturing Giant African Pouch Rats, Anthony Brown, John Christensen, Jared Harrison

Mechanical Engineering Design Project Class

We were tasked with designing a trap to safely capture Giant African Pouch Rats. The traps are used in both urban and rural environments that include city streets, basements, farms, river beds, and bushes among other locations. Pouch rats are much larger than most rats and are a very ferocious species; they will harm themselves if there are any non-smooth surfaces when captured. It is very important that we designed a trap with this safety top of mind.

Mems 411: Soccer Robot, Sam Ginsberg, Ella Johnson, Aaron Ocken, Andrew Bergantz

Mechanical Engineering Design Project Class

This design project was altered from the 2018 ASME Soccer Robot competition. Dr. Jackson Potter led a competition where groups built remote control robots to compete against each other in 1v1 matches based on a modified rule set from the initial 2018 competition.

Mems 411: Giant Pouched Rat Trap, Ronald Fields, Mariano Gonzalez, Edward Li, Jordan Hu

Mechanical Engineering Design Project Class

Dr. Braude from the Biology department at Washington University in St. Louis is currently working on a project training giant Gambian pouched rats to find mines and other bombs in former conflict zones. In order to trap Gambian pouched rats, Professor Braude asked a few MEMS 411 Senior Design groups to design and build a trap that can safely capture the rats. The trap had to be about 2-3 feet long, 6 inches in diameter, completely mechanical, simple, and it had to cost less than 30 USD to build.

Mems 411: Mini Test Frame, Howard Wu, Max Richter, Baker Blevins, Andrew Issac

Mechanical Engineering Design Project Class

A lightweight, cheap, and portable compression test frame designed for testing students' structural designs for the Machine Elements class. Measures load and displacement applied on the specimen to determine the specimen with the highest strength.

Mems 411: Giant Pouched Rat Trap, Shannon Wang, Isha Shah, Vaishali Shah, Elizabeh Saliba

Mechanical Engineering Design Project Class

Our goal is to design a giant pouched rat trap that meets the customer needs from professor Stan Braude. The giant pouched rats are to be breed and trained to find land mines. Therefore, the rats must be captured in good condition. However, giant pouched rats are not passive once caught and tries to escape every way possible. In the past, with traditional trap wires, they tend to get caught in the wire and hurt themselves. Our solution offers a completely smooth inner wall of the trap to prevent damage to the rats, while improving on the functionality of the …

Mems 411: Lost Grains Thresher, Alicia Gupte, Sophie Fox, Dan Heikes, Andrew Waldherr

Mechanical Engineering Design Project Class

The Lost Grains Thresher project aims to design and implement a device that can successfully separate the seed and chaff from various grains that are native to the greater St. Louis area. This project is designed for Dr. Natalie Mueller at Washington University in St. Louis to replace her current method of separating plant seeds from chaff by hand. This project focused on three main performance goals: 1) the device should work on a minimum of two types of seeds and thresh them to an acceptable quality, 2) the device should be easily cleaned and reset within three minutes, and …

Mems 411: Rowing Force Plate, Mae Hubel, Taylor Southwick, Miles Petersen

Mechanical Engineering Design Project Class

The Rowing Force Plate is a device that is designed to measure a rower’s force
over time so that they can understand how hard they are rowing. Most rowing
aids communicate the speed at which someone is rowing, which is variant on water
speed, wind speed, and other inconsistent environmental and situational factors.
Force, however, can be consistently measured and is a better indicator of effort a
rower is exerting. Other products that measure force do exist, but use complex and
expensive technology, unlike our design.
After brainstorming and analyzing multiple possible designs, we concluded to use
four force sensors …

Mems 411: The Bueffer 3000, Ty W. Bedillion, Krista Sudar, Anna Oneto, Cole Kocjancic

Mechanical Engineering Design Project Class

We were tasked with creating a quality product for a customer for MEMS 411 Senior Design. Our customer was the Washington University in St. Louis Men's Club Volleyball team and they asked us to create a volleyball setting machine.

Mems 411: The Hash Setting Slasher, Garrett Barber, William Koopman, Andrew Werner, Alexandra Carr

Mechanical Engineering Design Project Class

The volleyball setter has certain patents that utilize some sort of rotational component or is a stationary platform that the ball rests on before the player hits it. Our design is different because it utilizes the mechanical properties of springs to propel the ball forwards. We had certain specifications to meet to allow the volleyball to be natural in its trajectory and able to be shot efficiently and effectively. Some specifications required positioning adjustments and some defined how the ball should be propelled through the air. We also had parameters involving cost, weight, and the repeatability of the mechanism to …

Mems 411: Volleyball Setter, Alexander Zuga, Liam Cadden, Neil Cumberland, Jacob Ridderhoff

Mechanical Engineering Design Project Class

Our volleyball setting machine is intended for use by the WashU men’s club volleyball team to improve their training. It allows their skilled hitters to get more reps in practice because there currently aren’t enough skilled setters on their team.

Mems 411: African Pouched Rat Trap, Kelechi Achilefu, Paul Joseph, David Allen, Chase Green

Mechanical Engineering Design Project Class

What is often thought of as a rat trap is often in reality a mouse trap, or a trap designed to catch small rodents. Rats can be quite large and catching them without harming them can be quite difficult. Current market solutions generally either kill or harm the rodent which is not acceptable for our client's needs. While there are some solutions on the market, they fall short of the needs of our client which is more specialized due to the size of rodent they will be capturing, the circumstances surrounding the capture, the number of rodents our client needs …

Volleyball Crossbow- Group W, Giovanni Alvarez, Kyle Krippner, Alexis Rivera

Mechanical Engineering Design Project Class

The Volleyball Crossbow was our solution to the problem of a limited number of skilled setters on a volleyball team. This device will alleviate expectations of the setters and improve the efficiency of practice drills. The major customer needs for this device included consistency in launch, height and angle adjustability, high speed of operation, and ease of use. The Volleyball Crossbow provides a relatively low-cost, easy to manufacture design that meets these customer needs. As the name suggests, the design inspiration came from the crossbow mechanism. Two elastic bands attached to a cross-member and a cart on a track are …

Mems 411: P.O.T.T.E.R. Test Frame, Marie Drevets, Kiersten Horton, Tony Sancho

Mechanical Engineering Design Project Class

Our senior mechanical engineering design is a flexure test frame. At our university, third-year mechanical engineering students take a class called machine elements, in which the final project is a structural design competition. The students design a strong but lightweight object. The P.O.T.T.E.R. device can be used to judge the structural integrity of students contest entries. The customer who commissioned this project is Dr. Potter, who teaches the machine elements class. The customer needs a portable test frame which can apply enough compressive force to fracture an object which is secured in the device. The test frame should also measure …

Mems 411: Soccer Robot Project, Evan Sucherman, Dylan Mitchell, Benjamin Hessman, Emre Koc

Mechanical Engineering Design Project Class

This project aims at designing a robot that is capable of playing a simplified form of soccer against other robots. The original competition was created by the ASME organization as a student design competition in 2018. This project is an adapted version in which some of the rules and guidelines have been changed to fit the goals of this class better. The design parameters for this project include: having the robot drive around the parameter of the playing field in under 17 seconds, having the vehicle successfully capture the ball within 2 seconds of approaching 8 out of times, and …

Mems 411: Friction Frenzy, Angelo Hawa, Landon Tafoya, Noah Owens

Mechanical Engineering Design Project Class

The demo is designed to demonstrate the concept of friction to younger children(ages 4+) using an incline plane. The premise is to allow the user to slowly elevate a surface until a block resting on top begins to slide, at which point an electronic interface displays the calculated amount (or coefficient) of friction. The core functions of the device are discussed based on the customer needs in order to identify key performance goals for its successful operation. The design process is documented from initial modeling to the final prototype and critical metrics including safety and ease of fabrication are discussed. …

Mems 411: Asme Soccer Robot, Braden Arango, Brendan Otani, Florie Markwell

Mechanical Engineering Design Project Class

This project was based off of a variation of the ASME Soccer Robot Competition, where 5 teams were tasked with creating a soccer robot to compete with. The main objective for each team was to create a remote-controlled robot with an integrated shooting mechanism that was capable of shooting a tennis ball, with accuracy, into a goal. A design process was used to create this robot from scratch, where multiple concepts were created and tested through mock-ups and prototypes to better understand the problem at hand. Throughout this process, three main prototype goals were prioritized: the ability to drive around …

Mems 411: The Water Bike, Erin Flynn, Patrick Grindel, Nicholas Payne, Ryan Allin

Mechanical Engineering Design Project Class

This design project explored the concept of a bike that can float on water and be used to assist lifeguards in rescues. The goal was for it to be quickly converted from a road to water configuration and be quick and stable enough to be a useful tool in saving drowning swimmers.

Mems 411: Laundry No Mo (Lnm), Justin Tai, Minju Lee, Logan Johnson, Elijah Stewart

Mechanical Engineering Design Project Class

How can you optimize your time and labor while folding laundry? You can do so with this laundry folding device called Laundry No Mo (LNM).

Mems 411: Q.T. B-Bar, Gambian Pouched Rat Trap, Benjamin W. Horine Jr., Ileane Ho, Sarangi Pathirana

Mechanical Engineering Design Project Class

To design and build an improved rat trap that will effectively capture a Gambian Pouched Rat of larger size ensuring the rodents' safety, easy deployment in natural environments, simple mechanical release mechanisms, and cost-effectiveness.

Mems 411: Bearing Plate Loader, Daniel Firescu, Treeton Allison, Bethany Starr

Mechanical Engineering Design Project Class

Create a Bearing Plate Loader to move a plate from one location to another.

Mems 411: Soccer Robot, Luis Castro, Lydia Kang, Moshe Eskenazi, Ryan Whelan

Mechanical Engineering Design Project Class

The American Society of Mechanical Engineers (ASME) hosts annual competitions for engineeringstudents across the world. The ASME 2018 Student Design Competition wasto build a robotic soccerteam to compete in a FIFA World Cup style elimination tournament. Robot(s) must fit inside a 0.5 x 0.5 x 0.5 meter cube,be powered by batteries, and be controlled by a human operator with a wireless radio transmitter or through an electrical “umbilical” cord. The balls are tennis balls.