Engineering Commons^™

Mems 411: Soccer Robot, Luis Castro, Lydia Kang, Moshe Eskenazi, Ryan Whelan

Mechanical Engineering Design Project Class

The American Society of Mechanical Engineers (ASME) hosts annual competitions for engineeringstudents across the world. The ASME 2018 Student Design Competition wasto build a robotic soccerteam to compete in a FIFA World Cup style elimination tournament. Robot(s) must fit inside a 0.5 x 0.5 x 0.5 meter cube,be powered by batteries, and be controlled by a human operator with a wireless radio transmitter or through an electrical “umbilical” cord. The balls are tennis balls.

2021 (Fall) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the fall of 2019.

Conductive Polymer Spark Gap Igniters, Miranda P. Mcconnell, Allison K. Murray, Bryan W. Boudouris, I. Emre Gunduz, Steven F. Son, George T.-C. Chiu, Jeffrey F. Rhoads

Mechanical Engineering Faculty Research and Publications

Electrodes fabricated from electronically active polymers offer some benefits over those fabricated with common metals, including an appreciable resistance to corrosion and lower density. These benefits, and potentially others, manifest the advantages of using conductive polymers in lieu of metals for the mass production of ignition systems. In this work, spark gap igniters were fabricated using a potentially low-cost, roll-to-roll compatible process utilizing the doped conductive polymer polyaniline as the electrode material. Subsequently, nanothermite was printed on the spark gap igniters between the organic leads and ignited using a high voltage source to demonstrate the effectiveness of the device. All …

On The Need To Determine Accurately The Impact Of Higher-Order Sensitivities On Model Sensitivity Analysis, Uncertainty Quantification And Best-Estimate Predictions, Dan Gabriel Cacuci

Faculty Publications

This work aims at underscoring the need for the accurate quantification of the sensitivities (i.e., functional derivatives) of the results (a.k.a. “responses”) produced by large-scale computational models with respect to the models’ parameters, which are seldom known perfectly in practice. The large impact that can arise from sensitivities of order higher than first has been highlighted by the results of a third-order sensitivity and uncertainty analysis of an OECD/NEA reactor physics benchmark, which will be briefly reviewed in this work to underscore that neglecting the higherorder sensitivities causes substantial errors in predicting the expectation and variance of model responses. The …

Me-Em Enewsbrief, September 2021, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

An Investigation Of The Ignition Propensities Of Fuels Perturbed By Nitrogen Monoxide, Ackmer Robinson Iii

Theses and Dissertations

Quantitative structure property relationship (QSPR) regression models were developed based on the chemical functional group distribution of toluene reference fuels (TRF, mixtures of n-heptane, iso-octane, and toluene) for RON, MON, and DCN. The QSPR regression models were developed using DCN measurements from this study as well as RON/MON data available in literature. The correlations between RON/MON and DCN were analyzed. The ignition propensity of TRFs perturbed by NO addition was also investigated in this study. The interactions between the chemical functional groups and NO were investigated using an ignition quality tester (IQT). It was found that the increase in the …

Rip Curl: Community Activism For The Coast (The Ux Phase, Rip Curl And Sustainability, The Ui Phase), John Delacruz

Assignment Prompts

ADV 132 enables students to explore the craft and process of user experience and user interface design. They develop their skills within the context of a specific brief. The aim is to offer students the opportunity to immerse themselves in a particular problem and come up with creative solutions that will come to life on digital media platforms.

Leveraging Digital Transformation To Build The Technology Of Tomorrow Using Yesterday’S Equipment, Evan Barnett

Theses and Dissertations

Today’s industry sectors are filled with machines developed years ago. Healthcare, manufacturing, sustainment operations, and many others have equipment that may be reliable, but lacks certain capabilities that the newest technology delivers. The digital environment is becoming a necessity for users who want greater insights into how to improve their processes. A solution to this problem would be to purchase the newest equipment that contains robust measures to generate, collect, and analyze data. However, this solution may not be financially feasible for some and for others may sacrifice machine downtime and reliability. To combat these issues, this research focuses on …

Development Of Acoustic Metamaterial Noise Barriers And Simultaneously Harvesting Energy Using Smart Materials, Fariha Mir

Theses and Dissertations

In our surroundings abundant energy, we either feel through component vibration or hear noises from acoustic sources. Harvesting these unused and untapped green energy in the form of ambient vibration, and acoustic sounds is an emerging field of research in recent years. Utilization of the energy within a wide band of the frequency spectrum originated from the vibrational sources alone stands as one of the most promising ways to power small electronic devices, smartphones, local structural health monitoring sensors, home, and workshop appliances. These abundant sources of green energy are available in almost all the engineering industries, workshops, manufacturing facilities, …

Development Of A Rapid Compression And Expansion Machine To Characterize The Ignition Propensity Of Multi-Component Liquid Fuels, Jonathan Joseph Morreale

Theses and Dissertations

Combustion has been the primary source for energy production, whether it be from coal, oil, or natural gas, for a very long time. With increasing population and therefore an increased demand for energy, efficiency is becoming a concern. In order to increase efficiency, engines have been downsized and compression ratios have been increased. In doing so, problems have arisen such as knock and low speed pre-ignition. To better understand these problems, an investigation into how fuels ignite at higher pressures is necessary. Real fuels are comprised of multiple components that exhibit significant variations in their own physical and chemical characteristics. …

Searching Extreme Mechanical Properties Using Active Machine Learning And Density Functional Theory, Joshua Ojih

Theses and Dissertations

Materials with extreme mechanical properties leads to future technological advancements. However, discovery of these materials is non-trivial. The use of machine learning (ML) techniques and density functional theory (DFT) calculation for structure properties prediction has helped to the discovery of novel materials over the past decade. ML techniques are highly efficient, but less accurate and density functional theory (DFT) calculation is highly accurate, but less efficient. We proposed a technique to combine ML methods and DFT calculations in discovering new materials with desired properties. This combination improves the search for materials because it combines the efficiency of ML and the …

Effect Of Crystal Size On The Failure Mechanics Of Polymer Bonded Explosives, Chizoba Onwuka

Theses and Dissertations

Polymer bonded explosives (PBXs), typically constitute 80-95% of energetic crystals and 5-20% of a soft polymer binder, are widely used in extreme loading conditions such as rocket propellants and explosive munitions because of their high performance and low sensitivity. The particle size of crystals has a significant effect on the mechanical properties of most polymer particulate composites.

In the study, the effect of particle size on the deformation behavior of PBX under dynamic loading is investigated. The study involves testing polymer bonded sugar (PBS) samples, a well-known mechanical simulant of PBXs, with four different crystal sizes: coarse, intermediate, fine and …

Implementation Of Stereo Digital Image Correlation For In-Plane Strain Measurements To Quantify The Anisotropic Behavior, Plastic Flow, And Strain Hardening Of Extruded Aluminum Alloy, Farzana Yasmeen

Theses and Dissertations

The efficient use of metals is important in various industries, including aerospace, automotive, and energy systems. In each case, the type and range of combined loading conditions can be quite different. The approaches to stress analysis of such complex engineering components and assemblies often are limited to elastic conditions. For those cases where components are relatively thin, elastic-plastic conditions are present; there is continuing interest in assessing the accuracy of analytic and computational models for combined loading conditions. In such cases, experiments performed with axial and shear loads (e.g., tension-torsion) provide baseline data regarding the relationship between applied stresses and …

Application Of Digital Transformation In The Water Desalination Industry To Develop Smart Desalination Plants, Ibrahim Yousif

Theses and Dissertations

Fresh water shortage threatens the development and prosperity of many countries including several areas in the United States. Sea and ground water reverse osmosis desalination is rapidly becoming a dominant technology for overcoming water shortage threats by providing cost-effective freshwater production. Digital transformation can be used to help facilitate and advance water treatment technologies by reducing costs and minimizing downtime. Digital transformation is a process that encapsulates digital tools and technologies such as cloud computing, machine learning, artificial intelligence, the internet of things, and virtual/augmented reality. It is a process where objects in the physical world are given virtual replicas …

Multi-Fidelity Surrogate And Reduced-Order Model-Based Microfluidic Concentration Gradient Generator Design, Haizhou Yang

Theses and Dissertations

The microfluidic concentration gradient generator (μCGG) is an important device to generate and maintain concentration gradients (CGs) of biomolecules for understanding and controlling biological processes. However, determining the optimal operating parameters of μCGG is still a significant challenge, especially for complex CGs in cascaded networks. To tackle such a challenge, this study presents multi-fidelity surrogate and reduced-order model-based optimization methodologies for accurate and computationally efficient design of μCGGs.

The surrogate-based optimization (SBO) method is first proposed for the design optimization of μCGGs based on an efficient physics-based component model (PBCM). Various combinations of regression and correlation functions in Kriging and …

Mechanical Strength Of Sic Composite Tubing Under Uniaxial And Multiaxial Loading, Colton Corley

Theses and Dissertations

Silicon carbide fiber reinforced silicon carbide matrix composite is one of the candidate materials for accident tolerant nuclear fuel cladding concepts. In a Nuclear power plant, the reactions between the fuel, cladding, and coolant in a potential loss of coolant accident(LOCA) are of utmost importance to ensure safety in the accident tolerance of such plants. It is for this reason that SiC(silicon carbide) composite tubes have been selected as a possible alternative to the older Zirconium based cladding methods currently used in the industry, which were a partial cause of the Fukushima 2011 meltdown. To serve as fuel cladding, a …

Purification Of Uranium Tetrafluoride Using Ammonium Bifluoride, Kyle Robert Foster

Theses and Dissertations

Molten salt reactors are being deployed as one of the Generation IV nuclear reactor concepts starting in 2025. While their applications and safety potential are considered extremely advantageous, there is a lack of operating history to draw on, so thorough understanding of proposed molten salt materials’ thermochemical behavior is crucial to their successful implementation.

The most prominent fissile fuel proposed for molten salts is uranium tetrafluoride (UF4) using ²³³U of the thorium fuel cycle. UF₄ is extremely hygroscopic, meaning it will react with moisture and oxygen in its environment, so as-received powders contain significant levels of impurity. In …

Fabrication And Characterization Of Micro/Nanostructured Ceramic Device For Energy Conversion, Yun Gan

Theses and Dissertations

The deteriorating climate is threatening our living habitat and arousing public awareness. To achieve the carbon neutral goal by the middle of 21st century, developing novel technologies to reduce CO₂ emission or promote its capture become urgent. Among them, oxygen permeation membrane (OPM) and solid oxide cell (SOC) are two promising devices for clean energy conversion.

In chapter 1, the background of OPM and SOC are briefly introduced. Fundamental mechanism and application of phase inversion, the key process involved in fabrication of hollow fiber OPM and microtubular SOC are emphatically described. Mixed ionic and electronic conducting (MIEC) perovskites demonstrate …

Numerical Study Of Fully Coupled Fluid-Structure Interaction Of Stented Ureter By Varying The Stent Side-Holes, Erick Martinez, Ben Xu, Jianzhi Li, Yingchen Yang

Mechanical Engineering Faculty Publications

Ureteral stents are a measure used for many medical issues involving urology, such as kidney stones or kidney transplants. The purpose of applying stents is to help relieve the urine flow while the ureter is either blocked or trying to close itself, which creates blockages. These ureteral stents, while necessary, cause pain and discomfort to patients due to them being a solid that moves around inside the patients’ body. The ureter normally moves urine to the bladder through peristaltic forces. Due to the ureter being a hyperelastic material, these peristaltic forces cause the ureter to deform easily, making it necessary …

Automated Fiber Placement: A Review Of History, Current Technologies, And Future Paths Forward, Alex Brasington, Christopher Sacco, Joshua Halbritter, Roudy Wehbe, Ramy Harik

Faculty Publications

Automated fiber placement (AFP) is a composite manufacturing technique used to fabricate complex advanced air vehicle structures that are lightweight with superior qualities. The AFP process is intricate and complex with various phases of design, process planning, manufacturing, and inspection. An understanding of each of these phases is necessary to achieve the highest possible manufacturing quality. This literature review aims to summarize the entire AFP process from the design of the structure through inspection of the manufactured part to generate an overall understanding of the lifecycle of AFP manufacturing. The review culminates with highlighting the challenges and future directions for …

Centrifugal Spinning And Characterization Of Co3o4 Coated Carbon Fibers, J. Ayala, D. Ramirez, Elizabeth M. Fletes, Helia Magali Morales, Jason Parsons, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

Centrifugally spun polyacrylonitrile (PAN) microfibers surface-coated with Co3O4 nanoparticles (NPs) were prepared as precursors to produce coated Co3O4 carbon-composite fibers. The Co3O4/C composite fibers were obtained through a staged heating process during which the Co3O4PAN precursor fibers were stabilized over four hours at 200 °C, and subsequently the stabilized fibers were carbonized for six hours at 600 °C. The synthesis process presented in this work provides an effective strategy for the fabrication of surface coated-fiber materials, including composite fibers with good structure and morphology. The characterization of the Co3O4/C composite fibers was performed using SEM, EDS, XPS, XRD …

Justification Of The Main Parameters And Operating Modes Of The Crushers-Shredders Of Coarse Feed, K.D. Astanakulov, F.U. Karshiev, Sh.Kh. Gapparov

Irrigation and Melioration

The article presents the results of research on the justification of the parameters of the working bodies and operating modes of the mini crushers-shredders of coarse feed. On the basis of experimental research to study the effect of the rotor parameters Mini Crusher its qualitative performance indicators. According to the teachings found that rational parametres and operating modes-Crusher are: rotor length 350 mm; rotor diameter 550 mm; rotor speed 1290 min-1; the number of hammers 20 pcs; angle of rotation of the hammers 60.

Plan Dimensions Of The Flow Confinited By Cross Dams, On Rivers With Non-Symmetric Flooring, M.R. Bakiev, U.A. Kahhorov, A.А. Jakhonov

Irrigation and Melioration

Improving methods and technologies for calculating and designing floodplain transverse dams, taking into account the interaction of floodplain and riverbed flows to protect the banks from erosion and regulate riverbeds is one of the most important tasks. At the same time, the priority remains the transverse blind dams made of local soil with the attachment of their head. Their construction on rivers with two-sided asymmetric floodplains has its own characteristics, which consist in the need to take into account the morphology, the different roughness of the floodplain and the channel, the interaction of floodplain and channel flows, the asymmetry of …

Study Of Performance Of Vertical Drainage Well Construction From Polymer Materials, I.A. Akhmedov, Z.K. Mirkhasilova

Irrigation and Melioration

The article is devoted to the reconstruction and construction of vertical drainage wells. The use of vertical drainage wells is characterized by a decrease in the level of groundwater. The article presents data and typical regions of the use of vertical drainage wells.Also presented are mechanical, physical and chemical methods of well cleaning in practice. The information on the design and construction of vertical drainage wells is described. The analysis of corrosion resistance of vertical drainage well materials and their service life has been carried out. It is known that polymeric materials are resistant to corrosive environments. Using filters made …

Results Of Software Modeling Flow Section Of Vane Pumps, О.Я. Гловацкий, R.R. Ergashev, A.A. Abdullaev, J.I. Rashidov

Irrigation and Melioration

The article presents an analysis of data on the flow movement in a centrifugal pump, the results of which are aimed at improving the pump design in the direction of ensuring the flow of the flow without resistance to achieve energy savings in water transmission. To reduce slip on the pumps and to reduce the resistance to current flowing inside the pump to achieve energy savings, working impeller and spiral chamber shape are designed to be constructively correct. Data from pumping stations show that the performance of pumping equipment reduces water consumption by 10-12%, pressure by 18-20% and service life …

Economic Assessment Of A New Energy-Saving Electrical Technology For The Anesthesia Of Silkworms, O.A. Khaliknazarov, A.A. Turdiboev, D.M. Akbarov, D.M. Akbarov

Irrigation and Melioration

The article provides information on the role of Uzbekistan in the world in the field of cocoons, the analysis of cocoon cultivation and primary processing technologies, technologies and technical devices currently used in primary cocoon processing. Suggestion of the use of ultra-high frequency (UV) electromagnetic field in the anesthesia of mulberry silkworm, technical specifications of the electrotechnical device for anesthesia of mulberry silkworm using ultra-high frequency (UV) electromagnetic field, and the implementation of this device SK-150K pilons The cost-effectiveness of the device was assessed, the cost-effective method achieved as a result of the research work is highlighted. According to the …

Main Directions Of Food Security In Uzbekistan (The Case Of Samarkand Province), F.J. Saydullaeva

Irrigation and Melioration

The article assesses food availability as one of the indicators of food security on the example of Samarkand region based on a comparative analysis of the state of agricultural food production over the years and the volume of products per capita and their compliance with established recommended consumption norms. Based on the analysis, the results show that in Samarkand region in 2016-2020, agricultural food products were produced over recommended consumption norms per capita. The periodic evolution of the types of agri-food products produced by dehkan farms and owners of household land increased by 7.1% decreased by 7.3% on private farmers. …

The Economic Assessment Of Factors Affecting Small Household(Tomorka) In Rural Areas And Their Income, Sh.A. Muratov

Irrigation and Melioration

In this research, the role and importance of income from small householding(tomorka) in rural areas, its specific features are analyzed. Economic factors were assessed through the tobit regression model of the factors influencing the formation of income from small households (tomorka) activities, and VIF (Variance inflation factor) test was conducted to determine their multicollinearity. Anonymous surveys of 170 landowners in 4 districts of Samarkand region have been used in the analysis. The age of landowners, the area of arable land, the consumption of organic and mineral fertilizers, the cost of seeds and seedlings, the cost of preparing the field for …

Poly(2-Hydroxyethyl Methacrylate) Hydrogels For Contact Lens Applications–A Review, Kushendarsyah Saptaji, Nurlaely Rohmatul Iza, Sinta Widianingrum, Vania Katherine Mulia, Iwan Setiawan

Makara Journal of Science

The emerging technology in biomedical engineering requires biocompatible materials, which are also referred to as biomaterials. For a material to be considered biocompatible, it should not interact with human tissues in a harmful way, and vice versa. Various properties of biocompatible materials, such as mechanical and optical properties, have to be considered for different biomedical applications. One of the most popular applications of biomaterials is for contact lenses. Hydrogels, specifically poly(2-hydroxyethyl methacrylate) (PHEMA) hydrogels, are among the most popular ones in ophthalmologic applications, especially in soft contact lenses. This paper reviews the use of PHEMA hydrogels as one of the …

Building A Biomechanical Model Of A Rat Forelimb, Joshua Nathaniel Eric Mak

Dissertations and Theses

This paper presents a biomechanical model of the rat forelimb to test theories of determining viscoelastic muscle parameters. Several biomechanical models of rat hindlimbs have been developed and have explored the effects of multi-muscle control during locomotion. The forelimb model uses two ball-and-socket joints to model clavicle and scapula movement. A third ball-and-socket joint is used at the shoulder and two hinge joints are used at the elbow and wrist. Scapula motion is further constrained by muscle and spring elements. Each forelimb has 11 degrees of freedom, and 23 Hill-type muscles. The model has been created in Animatlab, which includes …