Engineering Commons^™

Mechanical Properties Of Kenaf Composites Using Dynamic Mechanical Analysis, Thomas A. Loveless

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Natural fibers show potential to replace glass fibers in thermoset and thermoplastic composites. Kenaf is a bast-type fiber with high specific strength and great potential to compete with glass fibers.

In this research kenaf/epoxy composites were analyzed using Dynamic Mechanical Analysis (DMA). A three-point bend apparatus was used in the DMA testing. The samples were tested at 1 hertz, at a displacement of 10 μm, and at room temperature.

The fiber volume content of the kenaf was varied from 20%-40% in 5% increments. Ten samples of each fiber volume fraction were manufactured and tested. The flexural storage modulus, the flexural …

Systems Modeling And Economic Analysis Of Photovoltaic (Pv) Powered Water Pumping Brackish Water Desalination For Agriculture, Michael A. Jones

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The objective of this study was to determine the economic viability of solar powered water pumping and desalination systems for agriculture. Growing global demand for agricultural production has put increased pressure on limited freshwater resources in various locations around the word. Many areas have low quality groundwater resources that have not been utilized for agriculture due to limited availability to electricity, high operational costs of diesel generators and the economics associated with water pumping and processing. Reverse osmosis is a desalination technology that removes salts and other minerals from low-quality water, making it fit for drinking or irrigation. Reduced costs …

Effective Properties Of Randomly Oriented Kenaf Short Fiber Reinforced Epoxy Composite, Dayakar Naik L.

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Natural fibers have drawn attention of researchers as an environmentally-friendly alternative to synthetic fibers. Developing natural fiber reinforced bio-composites are a viable alternative to the problems of non-degrading and energy consuming synthetic composites. This study focuses on (i) the application of kenaf fiber as a potential reinforcement and, (ii) determining the tensile properties of the randomly oriented short kenaf fiber composite both experimentally and numerically. Kenaf fiber micro-structure and its Young's modulus with varying gage length (10, 15, 20, and 25.4 mm) were investigated. The variation in tensile strength of kenaf fibers was analyzed using the Weibull probability distribution function. …

Surface Characterization Of 316l Stainless Steel For Biomedical Applications, Lawrence Cano

Theses and Dissertations - UTB/UTPA

Stainless steel alloys play an important role in the field of biomaterials due to their exceptional corrosion resistance and biocompatibility. These alloys have the capability to enhance the quality of a human life by altering various structures of human physiology. The close proximity these alloys have with destructive body fluids, ion dissolution is a detrimental cause from the corrosion initiative and may cause unfavorable reactions. A view on developing an improved compatible surface for the human body leads to implementation of different chemical surface modifications used for creating features that must be corrosion resistant and biologically active without changing the …

Carbon Dioxide (Co2) Emissions, Human Energy, And Cultural Perceptions Associated With Traditional And Improved Methods Of Shea Butter Processing In Ghana, West Africa, Emily Adams

USF Tampa Graduate Theses and Dissertations

The shea tree is indigenous to 21 countries in Sub-Saharan Africa and provides nuts from which oil (referred to as butter) can be extracted. Shea butter production in the Northern Region of Ghana is of socioeconomic importance to female processors who practice shea production. This study quantified the environmental effects of shea processing from carbon dioxide emissions and the human energy expended through the traditional, improved, and centralized methods of shea processing. Par-boiling accounted for up to 88% of total carbon dioxide emissions throughout the entire shea butter production process. A difference of 2.5(CO₂ (kg))/(Shea butter (kg)) emitted observed …

A Field Investigation Of Composite Mud Brick Compressive Strength, Kevin D. Hale

Dissertations, Master's Theses and Master's Reports - Open

It has been highlighted in numerous publications that in the field of earth construction there is a strong disconnect between experimental work in the laboratory and its application in the field. The current study attempts to help bridge this gap with a field test conducted in Nampula, Mozambique. Mud bricks were made with a simple hand mold and reinforced with bamboo and straw fibers. Fibers were cut into lengths of 3 cm and 6 cm while being mixed in fractions of 0.125%, 0.25% and 0.50% by weight and compressive strength was measured using an application of the 3-point bending test. …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

A Market-Based Approach To 3d Printing For Economic Development In Ghana, Wade Aitken-Palmer

Dissertations, Master's Theses and Master's Reports - Open

The purpose of this report is to create the foundation for further study of a market-based approach to 3D printing as an instrument for economic development in Ghana. The delivery of improved products and services to the most underserved markets is needed to spur economic activity and improve standards of living. The relationship between economic development and the advancement of technology is considered within the context of Ghana. An opportunity for market entry exists within both the bottom of the economic pyramid and the mid-segment market. 3D printing (additive manufacturing) has proven to be a disruptive technology that has demonstrated …

Kinematic Analysis And Simulation Of Theo Jansen Mechanism, Mehrdad Mohsenizadeh, Jenny Zhou

Early Career Technical Journal (ECTJ)

Section 3: Dynamic Systems & Control; pp. 98-106

Mechatronic Education At The Faculty Of Technical Sciences Novi Sad, Gordana Ostojić, Vukica Jovanović, Drazan Kozak, Zeljko Ivandić, Stevan Stankovski

Engineering Technology Faculty Publications

The emerging engineering field of mechatronics has caught the attention of many engineering professionals, academics and government officials in recent years, nationally and globally. The main reason for this is that many modern products are no longer purely electrical and electronic or mechanical. Moreover, they are integrated multidisciplinary products which are made from subsystems which require engineering knowledge of different disciplines. Hence, increasing number of universities is offering courses, certificates and programs at undergraduate and graduate levels in the area of mechatronics. This paper presents an educational program in mechatronics at the Faculty of Technical Sciences, University of Novi Sad, …

Design And Implementation Of An Interactive Animatronic System For Guest Response Analysis, Brian Burns

College of Graduate Studies: Theses & Dissertations

In theme park based entertainment applications, there is a need for interactive, autonomous animatronic systems to create engaging and compelling experiences for the guests. The animatronic figures must identify the guests and recognize their status in dynamic interactions for enhanced acceptance and effectiveness as socially interactive agents, in the general framework of human-robot interactions. The design and implementation of an interactive, autonomous animatronic system in form of a tabletop dragon and the comparisons of guest responses in its passive and interactive modes are presented in this work. The dragon capabilities include a four degrees-of-freedom head, moving wings, tail, jaw, blinking …

System Integration Of Hydrogen Energy Technologies Using Renewable Energy Resources, Tarek A Mohammed Hamad

Doctoral Dissertations

"The objective of this work has two major tasks that investigation the use of CHHP system at the Missouri University of Science and Technology (Missouri S&T) campus and studying solid waste as renewable source of energy: current and future possibility in Libya. Task one has three major topics. In Topic I, Design of Combined Hydrogen, Heat and Power (CHHP) system for the campus using local resources and treated biogas can be used to generate CHHP using a Molten Carbonate Fuel Cell (MCFC). In Topic II, hydrogen recovery and cleaning system, Heat recovery and electric power usage, hydrogen compression, storage, and …

Local Alternative Sources For Cogeneration Combined Heat And Power System, Abdulhakim Amer Agll

Doctoral Dissertations

"Global demand for energy continues to grow while countries around the globe race to reduce their reliance on fossil fuels and greenhouse gas emissions by implementing policy measures and advancing technology. Sustainability has become an important issue in transportation and infrastructure development projects. While several agencies are trying to incorporate a range of sustainability measures in their goals and missions, only a few planning agencies have been able to implement these policies and they are far from perfect. The low rate of success in implementing sustainable policies is primarily due to incomplete understanding of the system and the interaction between …

Process Improvements Of Cilantro Harvesting With Ergonomic Considerations, Eric Penningroth, Branden Shimamoto

Industrial and Manufacturing Engineering

The problems presented by Talley Farms to the team were a lower than desired cilantro harvesting capacity and work health pertaining to lower back problems. The project objectives were to address and improve upon both of these objectives. To increase harvesting capacity, a simulation model was created using standard times from time studies. The simulation model helped to compare the different harvesting methods as well as the effect of the utilization of the on-site manager. The throughputs between each of the models were analyzed. To address ergonomic concerns, a work sampling study was conducted and it was determined that kneeling …

Ole Miss Engineer 2014-2015

Ole Miss Engineer

No abstract provided.

Cal Poly India Project, Derek Babine, Austen Hibler, Alex Hernandez

Mechanical Engineering

This report documents the research, ideation, and development of a solution, implemented by the Cal Poly India Sanitation Team per the request of Mr. Harish Bhutani, to solve the problem of hazardous human waste management in poor villages in India. The sponsor envisioned a universal design that would give each household in those villages access to a private toilet system because the current solution is open defecation in water sources and farming fields. The initial constraints required the project be low cost, not use of electricity or water, have the ability to cater to an 8-10 person household, and be …

Analysis And Optimization Of The Scheffler Solar Concentrator, Simone Alberti

Master's Theses

The Scheffler reflector is a new solar concentrator design which maintains a fixed focus while only having a single axis tracking mechanism. This design makes the construction and operation of high temperature solar concentrators accessible to developing nations. In this project, I wrote computer simulation codes to better understand the dynamics and the effect of deformation or deviations from ideal conditions in order to define necessary manufacturing and operational tolerances. These tools and knowledge drove the prototyping of new reflector concepts by myself and other students on my team. A fiberglass prototype was able to drive the cost of a …

Carbon Black Mediated Conductive Polymer Composite, Mohamed Hussein Faris Ali

Theses

The central goal of this thesis is to produce electrically conductive nanocomposites made out of carbon black obtained from waste tires as filler into a polymeric matrix. Waste tires are discarded in substantial numbers on a daily basis, posing a significant environmental concern. By weight, about 25-35% of a tire is carbon black. Pyrolysis is a convenient and environmental friendly process to produce carbon black from tires. Due to carbon black’s low density, high electrical conductivity and economic feasibility, this thesis investigates the electrical conductivity of nanocomposites that utilizes carbon black particles as fillers. As a result of its modified …

A Collagen‐Glycosaminoglycan‐Fibrin Scaffold For Heart Valve Tissue Engineering Applications, Claire Brougham, Stefan Jockenhoevel, Thomas Flanagan, Fergal O'Brien

Conference Papers

The field of heart valve biology and tissue engineering a heart valve continue to expand. The presentatio ns at this meeting reflect the advances made in both areas due to the multi-disciplinary approach taken by many laboratories.

In Vitro Assessment Of Laser Sintered Bioactive Glass Scaffolds With Different Pore Geometries, Krishna C. R. Kolan, Albin Thomas, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The pore geometry of bioactive glass scaffolds intended for use in bone repair or replacement is one of the most important parameters that could determine the rate of bone regeneration. The pore geometry would also affect the mechanical properties of the scaffolds and their rate of degradation. Scaffolds with five different architectures, having ~50% porosity, were fabricated with silicate (13–93) and borate (13–93B3) based bioactive glasses using a laser sintering process. An established, late-osteoblasts/early-osteocytes cell line was used to perform cell proliferation tests on the scaffolds. The results indicated that the cells proliferate significantly more on the scaffolds which mimic …

Analysis Of Different Techniques For Improving Performance Of Flat Plate Solar Collectors For Fruits Drying, Godfrey Mbabaye

Tanzania Journal of Engineering and Technology (TJET)

Fruits drying had become a broader technology in fruits and vegetables value addition. The technology is reported to be a promising way of drying without incurring higher cost but its adaptation has not been feasible in rural areas. Solar dryers have been developed but its poor performance limits its applicability. In this study, several techniques for modifications of traditional solar collector were addressed. It was observed that, varying collector designs in different techniques, a range of collector performances can be archived. The research shows that, collector efficiency can be improved by 9.6% when employing double duct counter flow compared to …

Akabot: 3d Printing Filament Extruder, Emily Albi, Kevin Kozel, Daniel Ventoza, Rachel Wilmoth

Mechanical Engineering Senior Theses

3D printing could usher in a new age of localized manufacturing in places like Uganda, where three of our senior design team members spent the summer of 2013. Motivated by a concept for our senior design project, one of our team members interned with Village Energy, a small electronics business in Kampala, Uganda, as it piloted the use of a 3D printer to manufacture enclosures for its solar lights. The need for our project arose when we realized that although the 3D printer proved a viable method of manufacturing enclosures, Village Energy could not afford to continue 3D printing with …

Modeling And Experimental Investigation Of Parabolic Trough Solar Collector, Mohanad Abdulazeez Abdulraheem Alfellag

Doctoral Dissertations and Master's Theses

In this thesis, a mathematical model is applied to study the performance of a parabolic trough solar collector (PTSC). The proposed model consists of three parts. The first part is a solar radiation model. In this section, the amount of solar radiation incident upon Earth is estimated using equations and relationships between the sun and the Earth. The second part is the optical model. This part has the ability to determine the optical efficiency of PTSC throughout the daytime. The last part is the thermal model. The aim of this section is to estimate the amount of energy collected by …

Understanding The Global Energy Crisis, Eugene D. Coyle, Richard A. Simmons

Purdue University Press Books

We are facing a global energy crisis caused by world population growth, an escalating increase in demand, and continued dependence on fossil-based fuels for generation. It is widely accepted that increases in greenhouse gas concentration levels, if not reversed, will result in major changes to world climate with consequential effects on our society and economy. This is just the kind of intractable problem that Purdue University’s Global Policy Research Institute seeks to address in the Purdue Studies in Public Policy series by promoting the engagement between policy makers and experts in fields such as engineering and technology.

Major steps forward …

Assessing The Impact Of Water Filters And Improved Cook Stoves On Drinking Water Quality And Household Air Pollution: A Randomised Controlled Trial In Rwanda, Ghislaine Rosa, Fiona Majorin, Sophie Boisson, Christina Barstow, Michael Johnson, Miles Kirby, Fidele Ngabo, Evan A. Thomas, Thomas Clasen

Mechanical and Materials Engineering Faculty Publications and Presentations

Diarrhea and respiratory infections remain the biggest killers of children under 5 years in developing countries. We conducted a 5-month household randomised controlled trial among 566 households in rural Rwanda to assess uptake, compliance and impact on environmental exposures of a combined intervention delivering high-performance water filters and improved stoves for free. Compliance was measured monthly by self-report and spot-check observations. Semicontinuous 24-h PM2.5 monitoring of the cooking area was conducted in a random subsample of 121 households to assess household air pollution, while samples of drinking water from all households were collected monthly to assess the levels of thermotolerant …

Semiactive Virtual Control Method For Robots With Regenerative Energy-Storing Joints, Hanz Richter, Daniel J. Simon, Antonie J. Van Den Bogert

Mechanical Engineering Faculty Publications

A framework for modeling and control is introduced for robotic manipulators with a number of energetically self-contained semiactive joints. The control approach consists of three steps. First, a virtual control design is conducted by any suitable means, assuming a fully-actuated system. Then, virtual control inputs are matched by a parameter modulation law. Finally, the storage dynamics are shaped using design parameters. Storage dynamics coincide with the system's internal dynamics under exact virtual control matching. An internal energy balance equation and associated self-powered operation condition are given for the semiactive joints. This condition is a structural characteristic of the system and …

Water Access And Maintenance In Karonga, Malawi, Donald A. Norris

Dissertations, Master's Theses and Master's Reports - Open

This report is a case study of how Mwangalala community accesses water and how that access is maintained. Mwangalala community is located in the northern tip of Karonga district in Malawi, Africa. The case study evaluates how close the community is to meeting target 10 of the Millennium Development Goals, sustainable access to safe drinking water, and evaluates the current water system through Human Centered Design’s criteria of desirability, feasibility, and viability. It also makes recommendations to improve water security in Mwangalala community.

Data was collected through two years of immersive observation, interviews with 30 families, and observing two wells …

Creating Learning Through Service Opportunities For Engineering Students: Lessons Learned From A Primarily Undergraduate Liberal Arts University, Matthew Siniawski, Jose A. Saez, Jeremy Pal, Sandra Luca

Mechanical Engineering Faculty Works

The challenge of creating impactful and long-lasting service opportunities for engineering students lies in how to best implement programs in the unique setting of each academic institution. This paper presents a critical reflection of two different models of learning through service opportunities for engineering students that have evolved over the past six years at Loyola Marymount University. In particular, we highlight the history and lessons learned from four different case studies involving both extra-curricular international service projects and course-based service-learning opportunities for engineering students. Overall lessons learned that emerged from our experience include: 1) Students should receive course credit for …

Experimental Assessment Of Photovoltaic Irrigation System, Khalil Raza

Browse all Theses and Dissertations

Agriculture is a significant measure of an economy for a number of countries in the world. Currently, the agriculture sector relies heavily on conventional sources of energy for irrigation and other purposes. When, considering factors such as increasing costs of fossil fuels and extending new power lines, especially to remote locations where grid electricity is either inaccessible or expensive, a solar PV (photovoltaic) irrigation system can be an effective choice for irrigating farmland. Solar power eliminates the need to run electrical power lines to remote agriculture locations, which quickly turns the monetary equation in favor of solar irrigation over grid-powered …

Gas-Solid Bed Hydrodynamics Of Non-Spherical Particles, A S M Raufur Rahim Chowdhury

Open Access Theses & Dissertations

Gas-solid beds are ubiquitous in industrial and energy production applications. Examples include fluidized beds, which are used in many systems such as in Integrated Gasification Combined Cycle (IGCC) power plants or in chemical looping systems. These examples and others involve complicated interactions between each phase of reactants in the system. The motivation of this work stems from the need for a better understanding of bed hydrodynamics in existing energy systems; results from this work can be used directly in software such as Fluent to more accurately predict flow behaviors of gas and solid phases. The experimental data are collected from …