Engineering Commons^™

Design And Analysis Of A Novel Latch System Implementing Fiber-Reinforced Composite Materials, Francisco Guevara

Open Access Theses & Dissertations

The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of …

Reconfigurable Solid-State Dye-Doped Polymer Ring Resonator Lasers, Hengky Chandrahalim, Xudong Fan

Faculty Publications

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G) and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm² per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm² per pulse …

Sustainable Disposal Of Coal Processing Waste Streams, Mohammad Rezaee

Theses and Dissertations--Mining Engineering

Modern coal preparation facilities incorporate a wide array of solid-solid and solid-liquid separation processes for rejecting mineral matter to meet market specifications. The coarse mineral matter is typically placed into engineered refuse piles whereas the fine refuse is either stored in impoundments or co-disposed with the coarse refuse. The discharge water from the refuse material represents an environmental concern due to the potential release of trace elements, and the subsequent elevation of total dissolved solids and conductivity. The research findings reported in this dissertation addresses sustainable coal processing waste disposal through using strategies aimed at minimizing the environmental impacts. To …

Synthesis And Fabrication Of Graphene/Conducting Polymer/Metal Oxide Nanocomposite Materials For Supercapacitor Applications, Mohamad Khawaja

USF Tampa Graduate Theses and Dissertations

The rising energy consumption worldwide is leading to significant increases in energy production with fossil fuels being the major energy source. The negative environmental impact of fossil fuel use and its finite nature requires the use of alternative sources of energy. Solar energy is a clean alternative energy source; however, its intermittent nature is a major impediment that needs to be reduced or eliminated by the development of cost effective energy storage. Thermal storage in tanks filled typically with molten salt at elevated temperatures is widely used in concentrating solar power plants to generate electricity during periods of low daytime …

Studies Related To Microbially Induced Corrosion Of Stainless Steel 304 And 316, Somil Gupta

Electronic Theses and Dissertations

Pitting corrosion of stainless steel (SS) is observed in many different industries including the dairy industry. It is of concern, because it weakens the steel, and can cause cracking. Any replacement or repair of SS equipment is very costly and also causes delays in product manufacture. Microbial Induced Corrosion (MIC) is a possible accelerator of natural corrosion seen in galvanized steel pipes. Studies have shown a correlation between surface roughness and the ability of bacteria to colonize and form biofilms. Dairy industry utilizes higher food grade SS 304 and 316. However, even these relatively corrosion resistant stainless steel grades may …

Assessing Coupled Mechanical Behavior And Environmental Degradation At Submicron Scales, Samantha K Lawrence

Open Access Dissertations

Mechanical and electromechanical properties, deformation and fracture mechanisms, and environmental resistance of materials at submicron scales have been investigated through the combination of nanomechanical testing, high resolution microscopy, diffraction, and electrochemical testing. Nanomechanical techniques were used to isolate environmental, orientation, and size effects. Material evaluation focuses on metals, both model and engineering alloys, in bulk and thin-film form as well as oxide-substrate systems. Yield behavior of Ni 200, a model material, depends on sampled volume size, orientation, and surface preparation. Exposure to high-pressure hydrogen gas is also found to impact incipient plasticity and mechanical properties of commercially pure Ni 201. …

Kesterite Thin-Film Solar Cell Absorbers Derived Using Inhomogeneous Czts Nanoparticles, Wei-Chang D. Yang

Open Access Dissertations

My doctoral research focuses on understanding the structure-property-processing relationship of the kesterite materials to improve their device performance. It is recognized in both my own work and the recent literature that the structural and compositional integrities of CZTSSe are crucial to derive the solar cell grade kesterite thin-films. Analytical electron microscopy (AEM) allows me to demonstrate the structural and compositional inhomogeneity of the CZTS nanoparticles and CZTSSe thin-films at the nanoscale. For example, the observed forbidden reflections in TED patterns and FFT diffractograms corresponding to HRTEM images indicate that cation disorder leads to stacking faults in CZTS nanoparticles. Probe-corrected STEM …

Characterization And Mechanical Properties Of Solar Grade Silicon In Granular And Nanopowder Form, Mohamad Bilal Zbib

Open Access Dissertations

Polycrystalline silicon is mainly used for solar cell applications, structures in micro-electromechanical systems, and production of single crystal Si. One of the relatively new methods for producing large quantities of polysilicon is fluidized bed reactor (FBR), where two main morphologies are produced, granular solid (1-3 mm) and nanopowders (30-300 nm). Grinding and fracture occurs in the granular solid during shipping and handling which can affect the final product properties and create safety issues. The microstructure and the morphology of both the granular and the nanopowder forms of Si were examined using scanning and transmission electron microscopes (SEM and TEM). The …

Determination Of Current Density Distribution In An Electron Beam, Yudhishthir Prasad Kandel

Legacy Theses & Dissertations (2009 - 2024)

Electron beams are useful in many applications because they can be focused down to a spot far exceeding the physical limit of focusing visible light or x-rays. Additionally, electron beams are useful in transferring concentrated amounts of energy to a very small well defined region of a target for a fixed duration. This has led to the development of both scanning electron microscopes (SEMs) and electron beam lithography. The goal of this work was to develop a general method that accurately and easily yields the best estimate of the electron current density distribution of a focused electron beam, known as …

Study Of Millisecond Laser Annealing On Ion Implanted Soi And Application To Scaled Finfet Technology, Tyler J. Michalak

Legacy Theses & Dissertations (2009 - 2024)

The fabrication of metal-oxide-semiconductor field effect transistors (MOSFET) requires the engineering of low resistance, low leakage, and extremely precise p-n junctions. The introduction of finFET technology has introduced new challenges for traditional ion implantation and annealing techniques in junction design as the fin widths continue to decrease for improved short channel control. This work investigates the use of millisecond scanning laser annealing in the formation of n-type source/drain junctions in next generation MOSFET.

Optical Metrology For Directed Self-Assembly Patterning Using Mueller Matrix Spectroscopic Ellipsometry Based Scatterometry, Dhairya J. Dixit

Legacy Theses & Dissertations (2009 - 2024)

The semiconductor industry continues to drive patterning solutions that enable devices with higher memory storage capacity, faster computing performance, lower cost per transistors, and higher transistor density. These developments in the field of semiconductor manufacturing along with the overall minimization of the size of transistors require cutting-edge metrology tools for characterization.

Implementation Of Strategies To Improve The Reliability Of Iii-Nitride Photodetectors Towards The Realization Of Visible And Solar-Blind Imaging Arrays, John Bulmer

Legacy Theses & Dissertations (2009 - 2024)

Ultraviolet (UV) radiation detectors are being heavily researched for applications in non-line-of-sight (NLOS) communication systems, flame monitoring, biological detection, and astronomical studies. These applications are currently being met by the use of Si-based photomultiplier tubes (PMTs), which are bulky, fragile, expensive and require the use of external filters to achieve true visible-blind and solar-blind operation.

Initiated Chemical Vapor Deposition (Icvd) Polymer Thin Films : Structure-Property Effects On Thermal Degradation And Adhesion, Vijay Jain Bharamaiah Jeevendrakumar

Legacy Theses & Dissertations (2009 - 2024)

Opportunities and challenges for chemical vapor deposition (CVD) of polymer thin films stems from their applications in electronics, sensors, and adhesives with demands for control over film composition, conformity and stability. Initiated chemical vapor deposition (iCVD) is a subset of the CVD technique that conjoins bulk free-radical polymerization chemistry with gas-phase processing. The novelty of iCVD technique stems from the use of an initiator that can be activated at low energies (150 – 300 °C) to react with surface adsorbed monomer to form a polymer film. This reduces risk for potential unwarranted side-reactions.

Ion Implantation In Zno : Defect Interaction And Impurity Diffusion, Faisal Yaqoob

Legacy Theses & Dissertations (2009 - 2024)

In the first part of this research we studied the entropy changes in diffusion prefactor and its

High Frequency Signal Transmission In Through Silicon Via Based 3d Integrated Circuit, Min Xu

Legacy Theses & Dissertations (2009 - 2024)

Through silicon vias (TSVs) enable 3-dimensional (3D) integrated circuits (ICs), which have the potential to reduce the power consumption, interconnect length and overall communication latency in modern nanoelectronics systems. High-speed signal transmission channels through stacked silicon substrates are critical for 3D heterogeneous integration. This work presents systematic analyses of fabricated 3D IC test structures. This includes test structure design, fabrication, experimental characterization, equivalent circuit modeling and full wave simulations for high-speed signal transmission of the TSV based 3D IC channels.

The Impact Of Seed Layer Structure On The Recrystallization Of Ecd Cu And Its Alloys, Brendan B. O'Brien

Legacy Theses & Dissertations (2009 - 2024)

Despite the significant improvements originally offered by the use of Cu over Al as the interconnect material for semiconductor devices, the continued down-scaling of interconnects has presented significant challenges for semiconductor engineers. As the metal line widths shrink, both the conductivity and reliability of lines decrease due to a stubbornly fine-grained microstructure in narrow lines.

Carbon 1d/2d Nanoelectronics : Integration And Device Applications, Zhaoying Hu

Legacy Theses & Dissertations (2009 - 2024)

Graphene is a one-atom thick planar monolayer of sp2-bonded carbon atoms organized in a hexagonal crystal lattice. A single walled carbon nanotube (CNT) can be thought of as a graphene sheet rolled up into a seamless hollow cylinder with extremely high length-to-diameter ratio. Their ultra-thin body, large surface area, and exceptional electronic, optical and mechanical properties make these low-dimensional carbon materials ideal candidates for electronic applications. However, adopting low-dimensional carbon materials into semiconductor industry faces significant material and integration challenges. There is an urgent need for research at fundamental and applicative levels to find a roadmap for carbon nanomaterial to …

Design And Development Of Stress Engineering Techniques For Iii-Nitride Epitaxy On Si, Jeff Leathersich

Legacy Theses & Dissertations (2009 - 2024)

III-Nitrides have been a heavily researched material system for decades. Their material properties are favorable for a number of applications, most commonly in the optoelectronic and power device industry. Currently a majority of commercialized devices are fabricated on sapphire and SiC substrates but these are expensive and limit the widespread commercialization of the technology. There is substantial ongoing research geared toward the development of GaN on Si substrates because of the significant cost saving that would be realized through the inexpensive, large wafer and maturity of Si fabrication. Significant challenges with the deposition of GaN on Si have, thus far, …

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh

Research outputs 2014 to 2021

The influence of the Ar/O₂ gas ratio during radio frequency (RF) sputtering of the RuO₂ sensing electrode on the pH sensing performance is investigated. The developed pH sensor consists in an RF sputtered ruthenium oxide thin-film sensing electrode, in conjunction with an electroplated Ag/AgCl reference electrode. The performance and characterization of the developed pH sensors in terms of sensitivity, response time, stability, reversibility, and hysteresis are investigated. Experimental results show that the pH sensor exhibits super-Nernstian slopes in the range of 64.33-73.83 mV/pH for Ar/O₂ gas ratio between 10/0-7/3. In particular, the best pH sensing performance, in …

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

First-Principles Point Defect Models In Zr7ni10 And Zr2ni7 Binary Intermetallic Compounds And Their Implications In Nickel-Metal Hydride Batteries, Diana Felicia Wong

Wayne State University Theses

Zr-Ni-based alloys as nickel-metal hydride battery anode materials offer low-cost, flexible and tunable battery performance. Zr7Ni10 is an important secondary phase found in multi-phased AB2 Laves-phase-based metal hydride alloys, and the synergetic effect between the Zr-Ni and the Laves phases allows access to the high hydrogen storage of the Zr-Ni phases despite the lower absorption/desorption kinetics. Zr7Ni10 displays a small solubility window for Zr-rich compositions, while Zr2Ni7, with no solubility window, shows poor capacity with good kinetics. Stability of point defects within the crystal structure allows Zr7Ni10 to maintain the same structure at off-stoichiometric compositions, thus it is theorized that …

Temporally And Spatially Resolved Plasma Spectroscopy In Pulsed Laser Deposition Of Ultra-Thin Boron Nitride Films, Nicholas R. Glavin, Christopher Muratore, Michael L. Jespersen, Jianjun Hu, Timothy S. Fisher, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Physical vapor deposition (PVD) has recently been investigated as a viable, alternative growth technique for two-dimensional materials with multiple benefits over other vapor deposition synthesis methods. The high kinetic energies and chemical reactivities of the condensing species formed from PVD processes can facilitate growth over large areas and at reduced substrate temperatures. In this study, chemistry, kinetic energies, time of flight data, and spatial distributions within a PVD plasma plume ablated from aboron nitride (BN) target by a KrF laser at different pressures of nitrogen gas were investigated. Time resolved spectroscopy and wavelength specific imaging were used to identify and …

Engineered Fiber Reinforced Shotcrete For Efficient And Fast Ground Support Installation, N. Ginouse, S. Reny, M. Jolin

Shotcrete for Underground Support XII

No abstract provided.

Evaluation Of Wet-Mix Shotcrete Containing Set-Accelerator And Service Life Prediction, Marc Jolin, F. Melo, B. Bissonnette, P. Power, E. Demmard

Shotcrete for Underground Support XII

No abstract provided.

Transport Properties Of Wet-Mix Shotcrete, Lihe (John) Zhang, Dudley R. Morgan

Shotcrete for Underground Support XII

No abstract provided.

Comparison On Different Design Approaches Applied To A New Tunnel Lining System Reinforced By Tubular Arch, C.L. Zenti, R. Perlo

Shotcrete for Underground Support XII

No abstract provided.

New Technologies In Underground Projects: Drill Core Scanning, Documentation And Analysis, Jens Wiegand

Shotcrete for Underground Support XII

No abstract provided.

The Effect Of Spraying On Fiber Content And Shotcrete Properties, Marc Jolin, J.-D. Lemay, N. Ginouse, B. Bissonnette, É. Blouin-Dallaire

Shotcrete for Underground Support XII

No abstract provided.

Influence Of Calcium Sulfoaluminate Cement On The Pullout Performance Of Reinforcing Fibers: An Evaluation Of The Micro-Mechanical Behavior, Robert B. Jewell

Theses and Dissertations--Civil Engineering

The objective of this research was to determine the influence of calcium sulfoaluminate (CSA) cement on reinforcing fibers by evaluating the fiber pullout behavior, and bonding characteristics, of a single fiber embedded in a cementitious paste matrix. Four types of fibers commonly used in industry were evaluated: 1) Polyvinyl alcohol; 2) Polypropylene; 3) Coated Steel; and 4) Plain Steel.

Upward trends in energy costs and potential greenhouse gas regulations favor an increased use of construction materials that require lower energy and lower CO₂ emissions to fabricate, such as CSA cement, as opposed to the production of ordinary portland cement …