Engineering Commons^™

The Use Of Reclaimed Rubber From Waste Tires For Production Of Dynamically Cured Natural Rubber/Reclaimed Rubber/Polypropylene Blends: Effect Of Reclaimed Rubber Loading, A Thitithammawong, C Hayichelaeh, W Nakason, N Jehvoh

Journal of Metals, Materials and Minerals

Reclaimed rubber (RR) from waste tires was introduced into thermoplastic vulcanizates (TPVs) based on blends of natural rubber (NR)/RR/polypropylene (PP). The curing characteristics of NR/RR compounds together with properties of TPVs, i.e., mixing and dynamic vulcanization behaviors and mechanical, dynamic and morphological properties, were investigated with respect to RR content. The results show that the RR affects static and dynamic vulcanization of rubber molecules by increasing cure rate but lowers curing efficiency. Increasing the RR content in NR/RR/PP TPVs slightly reduces tensile strength but with a sharp impact on elongation at break. Dynamic properties reveal that elastomeric response of NR/RR/PP …

One Step Pressing-Annealing To Produce Ltp Mnbi Magnets, T Charoensuk, A Tamman, P Jantaratana, S Abbasi, C Sirisathitkul

Journal of Metals, Materials and Minerals

The production process for the high-purity low-temperature-phase (LTP) manganese bismuth (MnBi) magnets requires arc-melting, grinding and annealing materials under inert atmosphere. However, the formation of MnO is practically unavoidable during these steps since both Mn and MnBi are easily oxidized even by trace amounts of oxygen. In this work, an oxygen-free pressing-annealing system is developed to facilitate the synthesis of LTP MnBi with minimal oxidization. The semi-automatic pressing is carried out by using the compression piston and the load cell is used to measure the pressing force. The copper plate and cylindrical container are heated by nichrome filament heating. Mn …

Use Of Steam Explosion As A Green Alternative Method To Prepare Pulp From Pineapple Leaves, S Tanpichai, A Boonmahitthisud, S Witayakran

Journal of Metals, Materials and Minerals

The use of agricultural wastes as an alternative form of the cellulosic material to wood has gained considerable attention due to the reduction of deforestation. After cultivation, a large number of pineapple leaves are considered as a waste. Here, the potential steam explosion process was used as a green alternative way to prepare pulp from pineapple leaves without any addition of the chemical treatments. The pineapple leaf fibers were defibrillated from fiber bundles due to the rapid depressurization with the steam pressure between 16 and 20 kgf·cm-2. The partly removal of hemicellulose and lignin associated with the increase of the …

Characterization Of Zirconium Oxides Part I: Raman Mapping And Spectral Feature Analysis, Corey M. Efaw, Jordan L. Vandegrift, Michael Reynolds, Samuel Mcmurdie, Brian J. Jaques, Hui Xiong, Michael F. Hurley

Materials Science and Engineering Faculty Publications and Presentations

Raman mapping of sectioned zirconium cladding oxides was performed to analyze different spectral features before and after breakaway, as well as between zirconium and its alloys Zr-2.65Nb, Zry-3, and Zry-4. Oxide phase composition, or percent tetragonality, was defined to compare tetragonal to monoclinic zirconia. Percent tetragonality was spatially mapped to support distinction of zirconia phase distribution. A tetragonal-rich layer was seen at the metal/oxide interface, while post-breakaway samples exhibited increased amount of tetragonal phase in the bulk of their oxides. Spatial mapping of spectral peak location and half-width at half-maximum was accomplished to distinguish differences in stability mechanisms of tetragonal-rich …

Multifunctional Lightweight Aggregate Containing Phase Change Material And Water For Damage Mitigation Of Concrete, Wenyu Liao, Aditya Kumar, Kamal Khayat, Hongyan Ma

Materials Science and Engineering Faculty Research & Creative Works

This paper presents an innovative concept of multifunctional lightweight aggregate, which is produced by loading phase change material (PCM) into the interior of lightweight sand (LWS) and sealing the surface pores using water. The PCM loaded in the LWS functionalizes it as a temperature management agent in concrete, and the water in surface pores enables internal curing. It has been found that the particle shape and pore structure of crushed expanded shale LWS makes it an ideal carrier for PCM, loading sufficient PCM and maintaining better (compared to natural sand) mechanical interlocking. When coupled with the internal curing effect, the …

Accelerated Relaxation In Disordered Solids Under Cyclic Loading With Alternating Shear Orientation, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The effect of alternating shear orientation during cyclic loading on the relaxation dynamics in disordered solids is examined using molecular dynamics simulations. The model glass was initially prepared by rapid cooling from the liquid state and then subjected to cyclic shear along a single plane or periodically alternated in two or three dimensions. We showed that with increasing strain amplitude in the elastic range, the system is relocated to deeper energy minima. Remarkably, it was found that each additional alternation of the shear orientation in the deformation protocol brings the glass to lower energy states. The results of mechanical tests …

Publisher Correction: Pore Elimination Mechanisms During 3d Printing Of Metals (Nature Communications, (2019), 10, 1, (3088), 10.1038/S41467-019-10973-9), S. Mohammad H. Hojjatzadeh, Niranjan D. Parab, Wentao Yan, Qilin Guo, Lianghua Xiong, Cang Zhao, Mimglei Qu, Luis I. Escano, Xianghui Xiao, Kamel Fezzaa, Wes Everhart, Tao Sun, Lianyi Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The original version of this Article contained an error in Fig. 4. The x-axis labels in Fig. 4a, b were incorrectly labelled 'Diameter (mm)', rather than the correct 'Diameter (µm)'. This has been corrected in both the PDF and HTML versions of the Article.

Studies Of Initial Growth Of Gan On Inn, Alaa Alnami

Graduate Theses and Dissertations

III-nitride materials have recently attracted much attention for applications in both the microelectronics and optoelectronics. For optoelectronic devices, III-nitride materials with tunable energy band gaps can be used as the active region of devices to enhance the absorption or emission. A such material is indium nitride (InN), which along with gallium nitride (GaN) and aluminum nitride (AlN) embody the very real promise of forming the basis of a broad spectrum, a high efficiency solar cell. One of the remaining complications in incorporating InN into a solar cell design is the effects of the high temperature growth of the GaN crystal …

Study Of Amorphous Boron Carbide And Hydrogenated Boron Carbide Materials Using Molecular Dynamics And Hybrid Reverse Monte Carlo, Rajan Khadka

Graduate Theses/Dissertations

We present a computational study of amorphous boron carbide (a-B_xC) models using Molecular Dynamics (MD) studied with Stillinger-Weber (SW) and ReaxFF potential. The atomic structure factor (S(Q)), radial distribution function (RDF) and bond lengths comparison with other experimental and ab initio models shows that a random arrangement of icosahedra (B₁₂, B₁₁C) interconnected by chains (CCC, CBC) are present in a-B_xC. Afterward, Hybrid Reverse Monte Carlo (HRMC) technique is used to recreate a-B_xC structures. The existing SW potential parameters of Boron are optimized for the α-rhombohedral (Icosahedral B_{12 …}

Nanoscale Optical And Correlative Microscopies For Quantitative Characterization Of Dna Nanostructures, Christopher Michael Green

Boise State University Theses and Dissertations

Methods to engineer nanomaterials and devices with uniquely tailored properties are highly sought after in fields such as manufacturing, medicine, energy, and the environment. The macromolecule deoxyribonucleic acid (DNA) enables programmable self-assembly of nanostructures with near arbitrary shape and size and with unprecedented precision and accuracy. Additionally, DNA can be chemically modified to attach molecules and nanoparticles, providing a means to organize active materials into devices with unique or enhanced properties. One particularly powerful form of DNA-based self-assembly, DNA origami, provides robust structures with the potential for nanometer-scale resolution of addressable sites. DNA origami are assembled from one large DNA …

Mandela Splash Pad Pre-Construction Plan, Levi Sandbulte

Theses/Capstones/Creative Projects

In the construction industry, it is the responsibility of the general contractor to take the architect’s ideas and turn it into a real building. Many times this requires ample communication and several drafts. This efficient execution of this process is vital to the completion of a successful project. In this project, I practice this communication process. The challenge presented by the owner is to build an affordable splash pad, and without impacting the construction schedule of the Early Childhood Development Center (ECDC) that is being built on the same property at the same time. This proposal gives the owner a …

Modification Of Optical And Structural Properties Of Dc Magnetron Sputtered Tungsten Oxide Thin Films For Electrochromic Application, P Yaemsanguansak, M Sittishoktram, R Tuayjaroen, E Ketsombun, T Lertvanithphol, C Luangchaisri, T Jutarosaga

Journal of Metals, Materials and Minerals

The optical properties of tungsten oxide thin films prepared by a reactive DC magnetron sputtering technique were investigated. The influences of O2 flow rates (15 and 18 sccm) and DC sputtering powers (5, 15 and 25 W) on the optical properties of 200 nm-thick tungsten oxide films on indium tin oxide substrates (WO3/ITO/glass) were investigated using UV-visible spectrophotometer. The results indicated that the transmission modulation in visible region between colored state and bleached state of the films increased significantly with decreasing DC sputtering power and increasing O2 flow rate. The results corresponded with the increase of film roughness and density …

Ultrasonic Wave Propagation In Copper/Graphene Metal Matrix Composites, Casey Lindbloom

Mechanical Engineering Undergraduate Honors Theses

Emerging metallic composite materials implanted with graphene sheets are showing immense promise, with benefits being observed with regards to mechanical, thermal, and electrical material properties. This research aims to investigate the effects on ultrasonic wave propagation in Copper/Graphene Metal Matrix Composites (Cu/Gr MMCs) with varying graphene arrangements inspired from nacre and bone nanoscale material distributions. To accomplish this, the molecular dynamics (MD) method is utilized to simulate nanoscale wave propagation on a set of Cu/Gr MMCs with differing graphene arrangements and volume percentages ranging up to 4.56%. The computational model results are then analyzed to determine the variation in energy …

Graphene/Polypropylene Nanocomposites, Carmen Karam Abuoudah

Theses

Graphene has been regarded as a multifunctional nanofiller for manufacturing polymer nanocomposites. A small amount of graphene nanosheets is expected to significantly improve the properties of base polymers. The property enhancement, however, is a function of the degree of exfoliation and dispersion of graphene as well as its compatibility with the polymer. The non-polar nature of polyolefins such as polyethylene (PE) and polypropylene (PP) restricts the homogeneous dispersion of graphene, leading to significant agglomeration of the nanosheets and thus, limiting the expected property improvements in polyolefins. Currently, more efforts are focused on finding strategies to improve graphene dispersion in polyolefins. …

Effects Of Magnetic Domain And Twin Boundary Interactions On Magneto-Mechanical Properties Of Magnetic Shape Memory Alloys, Medha Veligatla

Boise State University Theses and Dissertations

Magnetic shape memory (MSM) alloys deform substantially when exposed to a magnetic field. This recoverable plastic deformation occurs through crystallographic twinning. Thereby the internal magnetic domain structure modulates the deformation mechanisms through the interaction of magnetic domains with twin boundaries. We study the meso scale magneto-structural interactions that affect the macroscopic material properties of MSM alloys. The study at the meso length scale is most effective as it allows for resolving interactions at magnetic domain wall width resolution with reasonable computing cost. We apply micromagnetics simulations to evaluate the evolution of magnetic domains, their interaction with twin boundaries, the distribution …

Machine Learning Predictions Electronic Couplings For Charge Transport Calculations Of P3ht, Evan D. Miller, Matthew L. Jones, Mike M. Henry, Bryan Stanfill, Eric Jankowski

Materials Science and Engineering Faculty Publications and Presentations

The purpose of this work is to lower the computational cost of predicting charge mobilities in organic semiconductors, which will benefit the screening of candidates for inexpensive solar power generation. We characterize efforts to minimize the number of expensive quantum chemical calculations we perform by training machines to predict electronic couplings between monomers of poly-(3-hexylthiophene). We test five machine learning techniques and identify random forests as the most accurate, information-dense, and easy-to-implement approach for this problem, achieving mean-absolute-error of 0.02 [× 1.6 × 10⁻¹⁹ J], R² = 0.986, predicting electronic couplings 390 times faster than quantum chemical calculations, …

Oxidation Behavior Of Welded Zry-3, Zry-4, And Zr–1nb Tubes, Jordan Vandegrift, Clemente J. Parga, Ben Coryell, Darryl P. Butt, Brian J. Jaques

Materials Science and Engineering Faculty Publications and Presentations

The Transient Reactor Test (TREAT) facility is a research reactor designed to simulate rapid transients to test new fuel designs. TREAT's cladding is exposed to unique conditions compared to normal water reactors. These conditions include: exposure to air at high temperatures (≥600 °C), rapid heating (≈700 °^C/_s), and cladding geometry that includes chamfers and welds. This work investigates the effects of chamfering and welding on the oxidation behavior of zirconium alloys (Zircaloy-3, Zircaloy-4, and Zr–1Nb). Tube specimens were examined under isothermal and transient conditions in dry and humid air. The effect of weld type (tungsten inert …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Nanothermomechanical Logic Gates For Thermal Computing, Ahmed Hamed

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Limited performance and reliability of electronic devices at extreme temperatures, intensive electromagnetic fields, and radiation found in space exploration missions (i.e., Venus & Jupiter planetary exploration, and heliophysics missions) and earth-based applications require the development of alternative computing technologies. Thermal computing, data processing based on heat instead of electricity, is proposed as a practical alternative and opens a new scientific area at the interface between thermal and computational sciences.

We successfully developed thermal AND, OR and NOT logic gates, achieved through the coupling between near-field thermal radiation and MEMS thermal actuation. In the process, we developed two novel non-linear thermal …

Magnetic Properties Of Nd–Fe–B Permanent Magnets Under Thermal Experimentation, Géraldine Houis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Neodymium-Iron-Boron (Nd-Fe-B) magnets were developed in the 1980s, and since then, they have appeared as a common component in many fields. From the industry to consumers or defense applications, from turbines, computers, cellphones to most audio systems, Nd-Fe-B magnets are present everywhere. But when Nd-Fe-B magnets are applied to the motors of electric vehicles and wind-turbine generators, their temperature rises, therefore Nd-Fe-B-Dy magnets are used. However, while the use of these magnets is common at low temperatures, their properties decrease dramatically with the increase of temperature. In this paper, the Nd-Fe-B-based samples used were prepared by using arc melting, melt …

Extending Mission Duration Of Uas Multicopters: Multi-Disciplinary Approach, Marc Lussier

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Multicopters are important tools in industry, the military, and research but suffer from short flight times and mission durations. In this thesis, we discuss three different ways to increase flight times and therefore increase the viability of using multicopters in a variety of missions. Alternate fuel sources such as hydrogen fuel and solar cells are starting to be used on multicopters, in our research we simulate modern fuel cells and show how well they currently work as the power source for multicopters and how close they are to becoming useful in Unmanned Aircraft System (UAS) technology. Increasing the efficiency in …

Piezoceramic-Polymer And Piezoceramic-Cement Composites: A Brief Review, S Inthong, S Eitssayeam, J Tontrakoon, T Tunkasiri

Journal of Metals, Materials and Minerals

The physical properties of piezoceramic-polymers and lead-based or lead-free - Portland cement or geopolymer are described as part of this brief review. The connectivities such as 0-3, 1-3, 2-2 and 3-3 were employed to fabricate the composites. Their physical properties such as dielectric, coupling constant, acoustic impedance etc. were measured. The acoustic impedance obtained from the PZT-epoxy resin (0-3/1-3 connectivity) showed quite low. This can be further developed to match with water or human tissue for both hydrophone and medical applications. The properties of the composites containing leadbased or lead-free cement or geopolymer were also revealed. The results prove that …

Isothermal Aging Of Al-Ni-Sc Alloy Containing Al3ni Microfibers And Al3sc Nanoprecipitates, C Suwanpreecha, J P. Toinin, P Pandee, D C. Dunand, C Limmaneevichitr

Journal of Metals, Materials and Minerals

Binary Al-Sc alloys have excellent strength at room and elevated temperature up to 300°C due to coherent of Al3Sc nanoprecipitates. Binary Al-Ni alloys are an alternative alloy for high-temperature applications owing to high-thermal stability of Al3Ni microfibers. In this study, the hardness evolution at 300°C for up to 672 h for eutectic ternary Al-6Ni-0.4Sc (wt%) was studied and compared with binary Al-0.4Sc and Al-6Ni alloys. The Al-6Ni alloy maintains a constant hardness after aging at 300°C up to 672 h. Both Al-0.4Sc and Al-6Ni-0.4Sc alloys show strong precipitation strengthening response, with peak hardness reached after about 3 h aging, due …

Evaluating The Grinding Process Of Granites Using The Physico-Mechanical And Mineralogical Properties, S Kahraman, M Ucurum, E Yogurtcuoglu, M Fener

Journal of Metals, Materials and Minerals

Granitic rocks are sometimes ground for different purposes. Predicting the mean particle size (d50) is useful for planning and cost estimation of purposes. In order to investigate the possibility of predicting the d50 of ground rock from the physico-mechanical rock properties, six different granites were tested in the laboratory. First, the d50 values were correlated with the corresponding physico-mechanical properties. The simple regression analysis showed that there were no good correlations between the d50 and the physico-mechanical properties. Then, the multiple regression analysis was carried out and strong prediction equations were developed. It was also shown that the dominant parameter …

Optical And Luminescence Investigation Of Er3+ Doped In Na2o-Al2o3-P2o5 Glasses For Photonics Material Application, N Chanthima, N Kiwsakunkran, J Kaewkhao, N Sangwaranatee

Journal of Metals, Materials and Minerals

Optical and photoluminescence properties of Er3+ doped Na2O-Al2O3-P2O5 (NAPEr) glasses were prepared by conventional melt quenching technique at 1200°C. The absorption spectra have 11 peaks corresponded to 4I15/2 ground state to various excited energy levels. The absorption band at 1537 nm shows highest intensity in near-infrared (NIR) region. Also, it can be observed that the intensity of absorption bands increased on increase in concentrations of Er2O3. The Judd-Ofelt (JO) parameters (Ωλ, λ = 2, 4, and 6) are calculated using the absorption bands of the Er2O3 doped glass compositions. McCumber theory has been applied to determine the emission cross-sections (σe) …

Deep Donors And Acceptors In Β-Ga2O3 Crystals: Determination Of The Fe2+/3+ Level By A Noncontact Method, Christopher A. Lenyk, Timothy D. Gustafson, Larry E. Halliburton, Nancy C. Giles

Faculty Publications

Electron paramagnetic resonance (EPR), infrared absorption, and thermoluminescence (TL) are used to determine the Fe^2+/3+ level in Fe-doped β-Ga₂O₃ crystals. With these noncontact spectroscopy methods, a value of 0.84 ± 0.05 eV below the conduction band is obtained for this level. Our results clearly establish that the E2 level observed in deep level transient spectroscopy (DLTS) experiments is due to the thermal release of electrons from Fe²⁺ ions. The crystals used in this investigation were grown by the Czochralski method and contained large concentrations of Fe acceptors and Ir donors, and trace amounts of Cr …

Synthesis And Applications Of Hematite Α-Fe2o3 : A Review, Muhamad Muhajir, Poppy Puspitasari, Jeefferie Abdul Razak

Journal of Mechanical Engineering Science and Technology (JMEST)

This article reviewed the hematite α-Fe2O3. It focuses on its material properties, nanostructures, synthesis techniques, and its numerous applications. Researchers prepared the hematite nanostructure using the synthesis methods such as hydrothermal, and, further, enhanced it by improving the techniques to accommodate the best performance for specific applications and to explore new applications of hematite in humidity sensing.

Failure Analysis On Titen Proto-Xx Car Chassis, Gaguk Jatisukamto, Rika Dwi Hidayatul Qoryah, Santoso Mulyadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The car chassis as a skeleton supports all loads and is the most important component. Car chassis requirements must be rigid, twisting resistant, vibration resistant and resistant to fatigue. This study aims to find the cause of the failure of the Titen Proto-XX car chassis connection. The research methodology was conducted by testing the composition of materials and structural analysis using Ansys Workbench Release 15.0 software. The conclusion of the research is that the skeletal structure material uses Aluminum AA series 1XXX with Al content greater than 99.5%, the welding ability is low, causing a failure in the welded joint. …

The Effect Of Chlorophyll Concentration From Papaya Leaves On The Performance Of Dye-Sensitized Solar Cell, Dede Rizali, Heru Suryanto, Sukarni Sukarni

Journal of Mechanical Engineering Science and Technology (JMEST)

Dye-Sensitized Solar Cell (DSSC) is the third generation solar cell that has sandwich structure consisted of organic dye material and other components such as titanium dioxide (TiO2) semiconductor, electrolyte, and substrates (counter electrode and working electrode). The dye in the device was made from green plant chlorophyll such as papaya. This research aimed to find the influence of dye concentration from papaya leaves chlorophyll on the performance of DSCC. The discussion covered the output power (Pout), Fill Factor (FF), and efficiency (ɳ). The method in this research was explorative experimental with independent variables such as direct and indirect sunlight. The …

The Flame Characteristics Of Diesel Fuel Blend With Kepuh (Sterculia Foetida) Biodiesel, Dani Hari Tunggal Prasetiyo, Nasrul Ilminnafik, Salahuddin Junus

Journal of Mechanical Engineering Science and Technology (JMEST)

Kepuh biodiesel fuel (sterculia foetida) is an alternative fuel that can be used to replace fossil fuel. Diesel fuel is performed to determine the laminar burning velocity and high flame by adding biodiesel kepuh volume of 10%, 20%, 30%. The purpose of this study was to study the effect of biodiesel and the effect of bunsen burners on the laminar burning velocity and flame height. Bunsen burner is made of copper and stainless steel. Testing of flame characteristics was carried out by heating the mixture of fuel and air at a temperature of 200°C. The purpose of heating the air …