Engineering Commons^™

Exploring The Variability In The Gray Scale Imaging Process Of Asphalt Samples, David Oluwawade Olatunji

Civil Engineering Undergraduate Honors Theses

Gray scale image analysis is a powerful tool for testing asphalt concrete materials. From material composition to surface properties, gray scale analysis has shown evidence as a non-invasive way to obtain information from asphalt samples. Casillas et al. used a gray scale analysis to measure the Representative Volume Element of three asphalt sample geometries to understand the minimum size at which an asphalt sample is representative of a larger homogeneous mixture [1]. While the gray scale analysis used in this experiment yielded results, there were unknown factors in the image capturing process. Particularly, not much was known about the effect …

Toward Understanding Underlying Mechanisms Of Drag Reduction In Turbulent Flow Control, Alex Rogge

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The underlying mechanisms of three different flow-control strategies on drag reduction in a turbulent channel flow are investigated by direct numerical simulations. These strategies include the addition of a small concentration of long-chain polymers into a fluid, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying drag-reduction mechanisms among these methods. The analysis is based on the …

Dyeing Properties And Color Fastness Of Eri Silk Yarn Dyed With Soaked Red Kidneybean Water, Piyaporn Kampeerapappun, Kritsana Wongwandee, Siriluk Janon

Journal of Metals, Materials and Minerals

The purpose of this research was to study the dyeing of eri silk yarn using soaked red bean water. The optimal condition for preparing dye solutions was a ratio of 1:5 of dried red bean to water and dyeing at 100°C for 45 min. The dyeing process was conducted with and without mordants, using three different mordanting methods; pre-mordanting, meta-mordanting, and post-mordanting. The effects on silk analyzed are color fastness to washing, wet and dry rubbing, acid and alkali perspiration, and color characteristics on CIEL*a*b* color coordinates.Without mordants, the dyed silk yarn gave a rosy brown color. Each mordant caused …

Effect Of Variations In The Composition And Size Of Red Sand Grains On The Quality Of K-225 Concrete, Mukti Hamjah Harahap, Aulia E. Putri

Journal of Metals, Materials and Minerals

The effect of variations in the composition and size of red sand grains on the solid quality made in the form of a 15×15×15 cm cubes were investigated. By implementing the standard of SNI K-225 which is a mixture of 1:1.9:2.8 with FAS 0.6 and the composition of red sand consisting of 0, 2, 4, 5,and 6.5% of the weight of fine aggregate and variations in the size of red sand grains of 80, 100, and 120 mesh, the concrete was being treated in a water bath for 28 days. It was tested by the method of water absorption, compressive …

Properties And Performance Of The Basalt-Fiber Reinforced Texture Roof Tiles, Parinya Chakartnarodom, Wichit Prakaypan, Pitcharat Ineure, Nutthita Chuankrerkkul, Edward A. Laitila, Nuntaporn Kongkajun

Michigan Tech Publications, Part 1

The mechanical and the physical properties, and the performance of texture roof tiles reinforced with the basalt fibers were observed. The samples of the basalt-fiber reinforced texture roof tiles were produced on the industrial scale by using filter pressing method. After forming, the as-molded samples were air cured and characterized based on ASTM C1185 standard for their mechanical properties and physical properties. In addition, the roof-tile installation test was also performed. The results showed that the samples of the basalt-fiber reinforced texture roof tile (BFRT) could be produced on the industrial scale by using the common setting of the forming …

Development Of Functional Materials And Devices On Flexible Platforms Using Additive Print Manufacturing Processes For Biomedical And Environmental Applications, Dinesh Maddipatla

Dissertations

In recent years, considerable research has been vested into the development of printed electronics (PE) to explore the best ways of fabricating electronic devices on flexible platforms using additive print manufacturing processes. PE produces flexible devices that are compatible with complex geometries, foldable applications and conformal to curved surfaces, with a promising potential for large‐area device fabrication at relatively lower manufacturing costs. This dissertation focuses majorly on the design and fabrication of novel flexible functional materials and devices for biomedical and environmental applications using additive printing processes.

Initially, a simple paper-based low cost and rapid prototypable platform with oxygen sensors …

High-Temperature Optoelectronic Device Characterization And Integration Towards Optical Isolation For High-Density Power Modules, Syam Madhusoodhanan

Graduate Theses and Dissertations

Power modules based on wide bandgap (WBG) materials enhance reliability and considerably reduce cooling requirements that lead to a significant reduction in total system cost and weight. Although these innovative properties lead power modules to higher power density, some concerns still need to be addressed to take full advantage of WBG-based modules. For example, the use of bulky transformers as a galvanic isolation system to float the high voltage gate driver limits further size reduction of the high-temperature power modules. Bulky transformers can be replaced by integrating high-temperature optocouplers to scale down power modules further and achieve disrupting performance in …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

Static And Dynamical Properties Of Multiferroics, Sayed Omid Sayedaghaee

Graduate Theses and Dissertations

Since the silicon industrial revolution in the 1950s, a lot of effort was dedicated to the research and development activities focused on material and solid-state sciences. As a result, several cutting-edge technologies are emerging including the applications of functional materials in the design and enhancement of novel devices such as sensors, highly capable data storage media, actuators, transducers, and several other types of electronic tools. In the last two decades, a class of functional materials known as multiferroics has captured significant attention because of providing a huge potential for new designs due to possessing multiple ferroic order parameters at the …

Soil-Cement Bricks Produced From Local Clay Brick Waste And Soft Sludge From Fiber Cement Production, Nuntaporn Kongkajun, Edward A. Laitila, Pitcharat Ineure, Wichit Prakaypan, Benya Cherdhirunkorn, Parinya Chakartnarodom

Michigan Tech Publications, Part 1

Soil-cement bricks were produced using local clay brick waste (CBW) and soft sludge (SS) from fiber-cement industries, preserving raw resources by substituting with industrial wastes. The control formula to produce soil-cement bricks, is 15 wt% Portland cement, 15 wt% sand, and 70 wt% laterite. Clay brick waste was added with values from 10 to 50 % of laterite weight in the control formula. For SS, 5 and 10 % was used to replace the total weight of the dry mixture in the control formula. The samples were shaped by using a manual brick making machine. The results showed that the …

Numerical Analysis Of A Roadway Piezoelectric Harvesting System, Abdul Rahman Badawi

Mechanical & Aerospace Engineering Theses & Dissertations

Highways, streets, bridges, and sidewalks with heavy traffic dissipate a considerable amount of waste mechanical energy every day. Piezoelectric energy harvesting devices are a very promising technology that can convert the waste mechanical energy to clean and renewable energy to enhance the sustainability of infrastructures. Research efforts in large-scale energy harvesting have led to the advancement of piezoelectric devices to the point that large-scale implementation is starting to become more feasible. The energy harvested by these devices can be used in many ways such as providing heating or cooling, melting ice, monitoring structural conditions in bridges and tunnels, and powering …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Synthesis, Characterization, Spectroscopic, And Mesomorphic Studies Of New Schiff Base Ligands And Titanium, Cobalt, Nickel And Copper Metal Centers, Raj K. Gurung

Chemistry & Biochemistry Theses & Dissertations

Transition metal complexes with Schiff base ligands offer a wide application in the field of development of catalysis and material. The straightforward synthesis allowed the structural modification and helped to optimize in various application of such complexes. Titanium-containing complexes have been reported to be important for their catalytic and material applications through the coordination of a tetradentate Schiff base ligand, viz. N, N’-ethylene bis(salicylideneiminate) dianion (salen). Studies reporting the characterization of achiral titanium(IV) salen complexes are scarce due to their intricate nature. Such complexes would be comparatively less expensive and easier to prepare synthetically and thus could represent an …

Characteristics Biolubricant Enriched With Nanoparticle Additives: A Review, Zhahra Hanif Sholiha, Gaguk Jatisukamto

Journal of Mechanical Engineering Science and Technology (JMEST)

The engine movement mechanism is a system composed of machine elements that contact or rub against each other between these surfaces. Surfaces that rub against each other will cause a friction force that causes wear on the surface, so it requires energy to fight the friction force. Lubricants are needed to reduce friction and reduce wear rates, where lubricants are generally made of mineral materials. Lubricants made from synthetic materials are non-renewable and cause environmental problems. The development of biolubricants as lubricating materials based on animal fats or vegetable oils is continuously being carried out. This study aims to observe …

Surface Properties And Adsorption Capacities Of Rice Bran-Activated Carbon, Dewa Ngakan Ketut Putra Negara, Tjokorda Gde Tirta Nindhia, Wayan Nata Septiadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The growing need for activated carbon requires alternative raw materials to replace non-renewable raw materials whose existence is decreasing. Biomass is a very promising precursor, one of which is from rice bran. This research concerns the development of activated carbon derived from rice bran. Carbonization was carried out at 600 OC and physically activated with nitrogen flow rates of 150 mL/min for 40, 80, and 120 minutes. The activated carbons produced (AC-D40, AC-D80, and AC-D120) were characterized to determine the surface properties, surface morphology, and adsorption capacity for nitrogen and blue methylene adsorptions. The results showed that activated carbon that …

Design Of Savonius Vertical Axis Wind Turbine For Vehicle, Filian Arbiyani, Fernando Pranata Lasut

Journal of Mechanical Engineering Science and Technology (JMEST)

The use of cellular phones is increasing in society, but due to the limited battery capacity of cell phones, it is necessary to charge the battery when travelling in the long distances. The Savonius type wind turbine has a potential as an energy source harvesting the wind energy flowing around the car. However, due to the available space on the car, careful design of Savonius vertical axis wind turbine for vehicle is necessary. The research is conducted numerically using MATLAB software. The wind speed, Reynolds number, and electric power output are numerically simulated to obtain the swept area design. Innovative …

The Effect Of Guide Vane Opening Variations And Total Blades On Cross Flow Turbine Performance Using Computational Fluid Dynamic, Muhamad Akbar Navis, Heru Suryanto, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is an agrarian country that continuously produces water, so it has the potential to develop a hydroelectric power plant. Computational Fluid Dynamic (CFD) application could be used to be an economical, quick, and efficient approach to improve the engineering design and turbine performance. This research aimed to find the effect of guide vane opening variations and total blades on cross-flow turbine performance using CFD simulation. This research used experimental modelling method with ANSYS program for turbine design with 22, 24, and 26 turbine blades and guide vane opening variations of 12°, 16°, 20°, 24°, and 36°. The data were …

Energy And Exergy Efficiency Of Double Slope Passive Solar Still, Jandri Fan Ht Saragi, Wawan Septiawan Damanik

Journal of Mechanical Engineering Science and Technology (JMEST)

Solar desalination functions to filter water, both sea water and brackish water, to produce clean water that is fit for consumption with energy from the sun. Solar energy is a renewable energy source that has been widely studied for its use. One of its uses is in a double slope passive solar still where the sun is the main source. Energy and exergy obtained from solar energy are not all used to evaporate water in the desalination system, so it is necessary to calculate efficiency energy and exergy in the system. This study aims to obtain data on the amount …

Optimization Of Stir Casting Of Aluminum Matrix Composites (Amcs) With Filler Of Recycled Glass Powder (Rgp) For The Mechanical Properties, Yusup Hendronursito, Tumpal Ojahan, Anang Anshori, Asep Yunanto

Journal of Mechanical Engineering Science and Technology (JMEST)

A study of making Aluminum Matrix Composites (AMCs) uses recycled glass powder (RGP) as a filler has been carried out through the stir casting process. The experimental design uses the Taguchi method of 3^3 orthogonal array L9 with the parameters of powder size (20>x> 80, 80>y> 200, 200>z> 325), percentage of filler vs matrix (2%, 7%, 12%), and stirring time (30 Seconds, 3 Minutes, 12 Minutes). The optimum conditions for the hardness of Al-GRp composites were obtained from specimens with Mesh powder size parameters 200> z> 325, the percentage of glass vs aluminum powder was 12% wt, …

New Design Of Aluminum 6061 Welding Joining Using Friction Stir Welding Method, Widia Setiawan, Nugroho Santoso, Surojo Surojo

Journal of Mechanical Engineering Science and Technology (JMEST)

Parallel, lap, corner, and T joints are commonly used in fusion welding and solid welding. Other joints made are lap and butt joint. This study aims to evaluate a new design of fitting model single U and double U for friction stirr welding of Aluminum. Aluminum sheet 6061with a thickness of 10 mm, will be cut to a length of 150 mm and a width of 100 mm, then a locking groove will be made with an inner size of 5 mm and a length of 150 mm The flow is used to be paired in the FSW process. This …

Tool Life Prediction Of Ti [C,N] Mixed Alumina Ceramic Cutting Tool Using Gradient Descent Algorithm On Machining Martensitic Stainless Steel, Joseph Daniel S, Senthil Kumar A

Journal of Mechanical Engineering Science and Technology (JMEST)

In automated manufacturing systems, most of the manufacturing processes, including machining, are automated. Automatic tool change is one of the important parameters for reducing manufacturing lead time. Machining studies on Martensitic Stainless Steel was conducted using Ti[C,N] mixed alumina ceramic cutting tool. Tool life was evaluated using flank wear criterion. The tool life obtained from experimental machining process was taken as training dataset and test dataset for machine learning. Tool life model was developed using Gradient Descent Algorithm. The accuracy of the machine learning model was tested using the test data, and 99.83% accuracy was obtained.

Moisture Reduction Of Honey In Dehumidification And Evaporation Processes, Anang Lastriyanto, Sasongko Aji Wibowo, Erwan Erwan, Firman Jaya, Jati Batoro, Dewi Masyithoh, J.S.A Lamerkabel

Journal of Mechanical Engineering Science and Technology (JMEST)

The high water content of honey can lead to fermentation and accelerate the deterioration of honey. One way to prevent fermentation in honey is to reduce the water content of honey. There are several ways to reduce the water content of honey, namely through a dehumidifier and evaporation. This study aimed to examine the relationship of reduced water content towards time in between dehumidifier and evaporation processes. The research method uses an exponential equation model to determine the value of the constant (K). The constant value (K) is used to predict the rate of reduction in moisture content between the …

Review Of Γ’ Rafting Behavior In Nickel-Based Superalloys: Crystal Plasticity And Phase-Field Simulation, Zhiyuan Yu, Xinmei Wang, Fuqian Yang, Zhufeng Yue, James C. M. Li

Chemical and Materials Engineering Faculty Publications

Rafting is an important phenomenon of the microstructure evolution in nickel-based single crystal superalloys at elevated temperature. Understanding the rafting mechanism and its effect on the microstructure evolution is of great importance in determining the structural stability and applications of the single crystal superalloys. Phase-field method, which is an excellent tool to analyze the microstructure evolution at mesoscale, has been gradually used to investigate the rafting behavior. In this work, we review the crystal plasticity theory and phase-field method and discuss the application of the crystal plasticity theory and phase-field method in the analysis of the creep deformation and microstructure …

The Economics Of Classroom 3-D Printing Of Open-Source Digital Designs Of Learning Aids, Nicole Gallup, Joshua M. Pearce

Michigan Tech Publications, Part 1

While schools struggle financially, capital for purchasing physical learning aids is often cut. To determine if costs could be reduced for learning aids, this study analyzed classroom-based distributed digital manufacturing using 3-D printing of open-source learning aid designs. Learning aid designs are analyzed in detail for their economic viability considering printing and assembly costs with purchased components and compared to equivalent or inferior commercial products available on Amazon. The results show current open-source 3-D printers are capable of manufacturing useful learning aids and that doing so provides high economic savings in the classroom. Overall, the average learning aid would save …

A First Investigation Of Agriculture Sector Perspectives On The Opportunities And Barriers For Agrivoltaics, Alexis Pascaris, Chelsea Schelly, Joshua M. Pearce

Michigan Tech Publications, Part 1

Agrivoltaic systems are a strategic and innovative approach to combine solar photovoltaic (PV)-based renewable energy generation with agricultural production. Recognizing the fundamental importance of farmer adoption in the successful diffusion of the agrivoltaic innovation, this study investigates agriculture sector experts’ perceptions on the opportunities and barriers to dual land-use systems. Using in-depth, semistructured interviews, this study conducts a first study to identify challenges to farmer adoption of agrivoltaics and address them by responding to societal concerns. Results indicate that participants see potential benefits for themselves in combined solar and agriculture technology. The identified barriers to adoption of agrivoltaics, however, include: …

Water Conservation Potential Of Self-Funded Foam-Based Flexible Surface-Mounted Floatovoltaics, Kaomi Soulemane Hayibo, Pierce Mayville, Ravneet Kaur Kailey

Michigan Tech Publications, Part 1

A potential solution to the coupled water–energy–food challenges in land use is the concept of floating photovoltaics or floatovoltaics (FPV). In this study, a new approach to FPV is investigated using a flexible crystalline silicon-based photovoltaic (PV) module backed with foam, which is less expensive than conventional pontoon-based FPV. This novel form of FPV is tested experimentally for operating temperature and performance and is analyzed for water-savings using an evaporation calculation adapted from the Penman–Monteith model. The results show that the foam-backed FPV had a lower operating temperature than conventional pontoon-based FPV, and thus a 3.5% higher energy output per …

Aerosol Jet Printed Capacitive Strain Gauge For Soft Structural Materials, Kiyo T. Fujimoto, Jennifer K. Watkins, Timothy Phero, Takoda Bingham, Kshama Lakshmi Ranganatha, Benjamin C. Johnson, Zhangxian Deng, Brian Jaques, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Soft structural textiles, or softgoods, are used within the space industry for inflatable habitats, parachutes and decelerator systems. Evaluating the safety and structural integrity of these systems occurs through structural health monitoring systems (SHM), which integrate non-invasive/non-destructive testing methods to detect, diagnose, and locate damage. Strain/load monitoring of these systems is limited while utilizing traditional strain gauges as these gauges are typically stiff, operate at low temperatures, and fail when subjected to high strain that is a result of high loading classifying them as unsuitable for SHM of soft structural textiles. For this work, a capacitance based strain gauge (CSG) …

Study On Cation Exchange Of A Lead Coordination Polymer Targeting Dynamic Mixed Cation Doped And Mixed-Valent Coordination Polymers, Hamisu Aliyu Mohammed

Student Works (2020-2029)

Solid solution in Metal-Organic Coordination Polymers (MOCPs) is an emerging synthetic pathway for modifying chemical compositions and has been expansively investigated. It has been demonstrated to be an important tool for engineering novel functional materials that otherwise have not been synthesized via the conventional technique. Although stable solid material with variable functionalities and intriguing structural motifs could be engineered by judicious selection of multivariate metal centers and multifunctional ligands. However, solid solution featuring mixed valence in MOCP is rare. Motivated by the ability of Pb2+ to adopt range of coordination numbers (CN) and chemical environments (CE), in addition to its …

Examination Of Early Stage Grey Iron Solidification Through The Development Of Fast-Quench Methodology, James C. Liggett

Honors College Theses

As grey iron casting accounts for a significant share of the foundry industry, proper understanding of the effects of solidification and growth mechanisms on the mechanical properties of grey iron is crucial. Prior experimentation has been performed examining early stage solidification and growth of the carbon phase of ductile iron, in which rapid quench samples are obtained which detail austenite-graphite interactions during solidification. This prior experimentation is built upon in though this research and applied to examine the early stage growth of flake graphite in grey iron. The purpose of this research is to validate a proposed fast-quench method by …

Radiation Modified Chitosan/Polyvinyl Alcohol Film With Polyvinyl Pyrrolidone Coating For Heavy Metal Ion Removal, Norhashidah Talip

Student Works (2020-2029)

Chitosan (CS) / Polyvinyl Alcohol (PVA) films were obtained by solution casting method. To be used in the water treatment application, these film need to be improved in mechanical strength. In this study, 2% (w/v) chitosan and 5% (w/v) PVA were blend at different CS: PVA weight ratios (50:50, 70:30 and 90:10). These mixtures were then transformed into films by solution casting method. Mechanical properties of the films were evaluated using tensile strength test where, at 70:30 of CS: PVA ratio gave the best tensile strength. Therefore, this composition was selected to proceed with the radiation modification with Polyvinyl Pyrrolidone …