Engineering Commons^™

Extraction Of Lutein Dye From Tagetes Erecta Garland Waste For Green Dyeing Of Hemp Fabric Using Response Surface Methodology, Pisutsaran Chitichotpanya, Nattaya Vuthiganond, Thitirat Inprasit, Benjamas Klaykruayat, Seranee Srisuk

Journal of Metals, Materials and Minerals

Large quantities of discarded flowers from religious observances are left at temples and other places of worship, causing global disposal and environmental issues. Recycling and transforming such organic waste into value-added products is one of the most effective and beneficial solutions to the problem. The main goal of this study is to convert the most abundant temple wastes of marigold (Tagetes erecta) flowers into an eco-friendly dyestuff for the textile industry. Our study assessed the suitability of dye extract from garland waste for dyeing hemp fabric and valuated indicators including color strength (K/S) and fastness properties using tannic …

Development Of Fexoy Particle Onto Bacterial Cellulose Network By Forced Hydrolysis And Its Electrical Conductivity, Prompong Khamwongsa, Poramed Wongjom, Andi Magattang Gafur Muchlisc, Chun Che Lin, Seranee Srisuk, Sarute Ummartyotin

Journal of Metals, Materials and Minerals

FexOy particle and bacterial cellulose composite sheet was successfully prepared by forced hydrolysis. The presence of Fe3+ ions in bacterial cellulose suspension significantly provided the positive charge due to electrostatic force as reported by Zeta potential. With the pH of 12 of bacterial cellulose suspension, particle was nucleated between bacterial cellulose networks. Fourier transform infrared exhibited Fe-O stretching. X-ray diffraction reported that the mixture of Fe2O3 and Fe3O4 was existed onto bacterial cellulose composite. Scanning electron microscope reported that FexOy particle was randomly distributed in bacterial cellulose network. Intensity of Fe was qualitatively observed by energy dispersive analysis. With the …

Morphology And Electrochromic Property Of Chemical Bath Deposited Nio Films At Different Niso4 Concentration, Watcharaporn Thongjoon, Kamon Aiempanakit, Itsarapong Chuasontia, Chantana Aiempanakit

Journal of Metals, Materials and Minerals

In this study, nickel oxide (NiO) films were prepared on indium tin oxide (ITO) glass by a chemical bath deposition (CBD) at different nickel sulfate (NiSO4) concentrations. The NiO films were verified for their structural properties with field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) while the optical properties were investigated using a spectrophotometer. Moreover, the NiO films were studied to assess their electrochemical properties by cyclic voltammetry in potassium hydroxide (KOH) electrolyte. The results showed that annealed NiO films exhibited the dominant crystal structure of the (111) plane. Meanwhile, the NiSO4 concentration controlled morphological structure between dense …

Optimized Parameter Of Dissimilar Joining Between Al6061-T6 And Height-Strength Steel With Friction Stir Spot Welding Process (Fssw), Anusak Silachai, Suriya Prasomthong

Journal of Metals, Materials and Minerals

High-strength steel and aluminum alloys are used to manufacture modern vehicles. The objective was to reduce the weight and fuel consumption of the vehicles. In this study the optimum parameters for the friction stir spot welding (FSSW) process between Al6061-T6 aluminum alloy and HSS590 high-strength steel were determined. Response surface methodology based on central composite design (CCD) with three parameters, five levels, and 19 runs was used to conduct experiments and develop mathematical regression models. The three joint parameters were tool speed, welding feed, and dwell time. Analysis of variance was then performed to examine the adequacy of the developed …

Synthesis And Characterization Of Hybrid Shell Microcapsules For Anti-Corrosion Ni-Co Coating, Hamed Sadabadi, Saeed Reza Allahkaram, Omid Ghader, Pradeep K. Rohatgi

Journal of Metals, Materials and Minerals

This paper presents the results of the study of microcapsules synthesized using a novel hybrid shell of polyureaformaldehyde/SiO2 (PUF/SiO2) and a core of linseed oil. The synthesis was accomplished by facial polymerization combined with sol-gel of TEOS, and urea-formaldehyde resin to form the hybrid shell under optimal process parameters. The microcapsules were embedded in a metal coating using the electrodeposition method. Microcapsules were characterized by scanning electron microscope (SEM, FE-SEM), energy-dispersive spectroscopy (EDS), particle size analyzer (PSA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The experimental results indicated that the average size of capsules synthesized umder the optimum processing …

Dyeing Of Curcumin And Durable Press Finishing With Citric Acid On Cotton Fabric Using One Step Process, Supannee Boonroeng, Piyaporn Kampeerapappun

Journal of Metals, Materials and Minerals

Cotton is an affordable and durable option for clothing. However, cotton garments tend to wrinkle easily. Therefore, cotton fabrics were studied to improve their wrinkle resistance properties. In this work, curcumin was mixed in an aqueous solution of citric acid and its catalyst and applied to cotton fabric using pad-dry-cure process for both the dyeing and finishing properties. Aloe vera extract and chitosan were used to compare for the reaction of their functional groups with carboxyl groups of citric acid on cotton fabrics. The mixture of curcumin and citric acid solution showed anti-wrinkle properties on the treated cotton. There were …

Mineralogical Studies And Optimization Of Tabling Parameters Of Low Grade Chromite Ore By Box Behnken Design Of Experiments, Amit Kumar Bhandary, Siddhartha Mukherjee, Rajib Dey, Mahua Ghosh Chaudhuri

Journal of Metals, Materials and Minerals

Chromite ore is geologically associated with gangue materials which have lower density compared to pure chromite (FeO.Cr2O3). Gravity separation techniques are very suitable for beneficiation of low grade chromite ore. In the present study mineralogical analysis of the sample has been carried out by using Wavelength dispersive x-ray fluorescence (WDXRF), X-ray powder diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive X-ray (EDX). The beneficiation of low grade (Cr2O3% 26.88) chromite ore has been investigated using wilfley table. Optimization has been carried out using box-behnken statistical design (BBD). The experimental parameters selected are: tilt angle, water flow rate and pre-heat …

Magnetic Nanoparticles Coated With Zwitterionic Copolymer As An Advanced Material For Rapid And Instrument-Free Biomolecular Detection In Human Serum, Supannika Boonjamnian, Varunee Sadsri, Voravee P. Hoven, Piyaporn Na Nongkhai

Journal of Metals, Materials and Minerals

The traditional agglutination assays especially those based on polystyrene beads have been recognized as convenient tools for disease diagnosis despite their limited detection range and low sensitivity. Unlike other particles namely polystyrene beads, SiO2 and gold nanoparticles having insignificant magnetic properties, magnetic nanoparticles (MNPs) offer unique advantages as their magnetic properties for agglutination methods. In the presence of magnet, not only can they be used to enrich the samples, but also their aggregation can also be induced, providing sensitive and rapid measurements. This work aims to develop MNPs for aggregation-based biomolecular detection. The MNPs were surface-modified with PMAMPC via an …

Mechanical Property Evaluation Of Additively Manufactured Materials Across A Wide Temperature Range, Sanket Vinayak Hirve

Electronic Theses and Dissertations

Additive manufacturing (also called 3d printing) has transitioned from a prototyping-only technology to a technology that is able to create usable parts with complex geometries. 3D printed parts are beginning to be used across all areas of engineering, such as biomedical, aerospace, automobile and many more. Typically, the term “3D printing” refers to layer by layer deposition of polymer materials, while the term “additive manufacturing” refers to layer by layer metal deposition. Conventional manufacturing, or substrative manufacturing, has several main problems that additive manufacturing can help overcome, such as high cost for low volume production, inability to create very complex …

Solution Atomic Layer Deposition Of Smooth, Continuous, Crystalline Metal-Organic Framework Thin Films, Maïssa K.S. Barr, Soheila Nadiri, Dong-Hui Chen, Peter G. Weidler, Sebastian Bochmann, Helmut Baumgart, Julien Bachmann, Engelbert Redel

Electrical & Computer Engineering Faculty Publications

For the first time, a procedure has been established for the growth of surface-anchored metal–organic framework (SURMOF) copper(II) benzene-1,4-dicarboxylate (Cu-BDC) thin films of thickness control with single molecule accuracy. For this, we exploit the novel method solution atomic layer deposition (sALD). The sALD growth rate has been determined at 4.5 Å per cycle. The compact and dense SURMOF films grown at room temperature by sALD possess a vastly superior film thickness uniformity than those deposited by conventional solution-based techniques, such as dipping and spraying while featuring clear crystallinity from 100 nm thickness. The highly controlled layer-by-layer growth mechanism of sALD …

Synthesis And Advanced Characterization Of Energy Materials, Erik Sarnello

Graduate Research Theses & Dissertations

Catalysts are used in an extremely broad range of systems including everything from biological systems to industrial processes. An ideal catalyst offers robust stability and high activity. This work focuses on the synthesis and characterization of materials that show promise in the field of catalysis. Advanced synchrotron characterization techniques and unique experimental design are highlighted to provide foundation work that will provide the necessary information to aid in designing and fabricating catalytic materials. Supported metal nanoparticle (SMN) catalysts are enormously crucial for many catalytic applications. However, catalyst deactivation, caused by sintering and coke formation, is a ubiquitous problem that significantly …

Induction Brazing, Austin Squire, Scott Compton, Logan Hathaway, Michael Fleming

Williams Honors College, Honors Research Projects

Our team would like to research and explore ways of designing a portable device that uses induction heating/brazing to connect two exhaust pipes together.

Electrochemical Chloride Removal, Marcus Yudt

Williams Honors College, Honors Research Projects

Electrochemical chloride removal (ECR) was tested to see its effectiveness in preventing corrosion on rebar samples within 3.5 wt% sodium chloride concrete. In order to do this, three scenarios were evaluated using electrochemical techniques such as cyclic potentiodynamic polarization and electrochemical impedance spectrsoscopy as well as visual inspections. The three scenarios that were evaluated were one with no chlorides present within the concrete, one that was a worst-case scenario where extreme pitting and corrosion were initiated, and one that had chlorides present and received the ECR treatment. Cyclic polarization curves showed that the ECR and reference without chlorides had similar …

Rational Design Of Metal-Organic Frameworks (Mofs)-Based Functional Materials Towards Better Air Quality, Zan Zhu

Theses and Dissertations

Air pollution is a major threat to environmental safety and public health. Volatile organic compounds (VOCs), particulate matter (PM), and airborne microorganisms are three typical air pollutants. Conventional strategies to prevent and mitigate air pollution have been employed, which, however, are generally passive. For instance, VOC sensing through solid-state devices is a conventional approach, which, however, is not capable of capturing and removing VOCs. On the other hand, air filters and face masks are useful equipment to protect people from inhaling PM and airborne microorganisms. But most commercial filters can only capture them on the surfaces, which may cause secondary …

Effects Of Additive Manufacturing Techniques On The Magnetocaloric Properties And Chemical Stability Of Lafexcoysi13-X-Y Alloys, Binyam Wodajo

Theses and Dissertations

Additive manufacturing (AM) is an emerging process to fabricate net shape, intricate, engineering components with minimal material waste; however, traditionally it has been largely applied to structural materials. AM of functional materials, such as magnetic materials, has received much less attention and the field is still in its infancy. To date, AM of magnetocaloric regenerators for magnetic refrigeration (an energy-efficient alternative to the conventional vapor-compression cooling technology), remains a challenge. There are several magnetic refrigerator device designs in existence today that are predicted to be highly energy-efficient, on condition that suitable working materials can be developed. This challenge in manufacturing …

Pilot-Scale Spinning And Sucrose-Tetra-Aldehydes-Crosslinking Of Feather-Derived Protein Fibers With Improved Mechanical Properties And Water Resistance, Bingnan Mu, Faqrul Hassan, Qianmei Wu, Yiqi Yang

Department of Textiles, Merchandising and Fashion Design: Faculty Publications

Pliable and water-resistant protein fibers from feathers were developed via continuous one-step spinning and crosslinking using sucrose-tetra-aldehydes. Though flexible protein fibers from feathers were developed, poor wet stability and low tenacity still limit the large and high-end applications of feather-derived fibers. Despite that saccharide aldehydes are considered as an efficient and sustainable crosslinker, substantial concerns such as generation of formaldehyde, high consumption of modifiers, loss of mechanical properties, yellowing, and decline in dyeability of fibers, exist after crosslinking. In this work, we controlled structures of crosslinkers and incorporated disaccharide-tetra-aldehydes into a continuous wet-spinning line. No formaldehyde was generated in the …

Effect Of Thiosulfate On The Passivation Of Zinc-Alloyed Anodes, (Z32120 And Z13000) At 80°C After 288h Immersion In 3.5% Nacl Solution, Thwelt Thinzar Zaw

Chulalongkorn University Theses and Dissertations (Chula ETD)

In this research, the inhibition of passivation on Zn alloys (Z32120 with Al) and Z13000 without Al) in artificial seawater (3.5% NaCl) mixing with different thiosulfate concentrations (100ppm, 150ppm, 200ppm) were investigated electrochemically after 288h immersion at 80°C and compared the results with that of testing without thiosulfate in the environment. According to the Potentiodynamic polarization test results, it is found that the presence of thiosulfate (S2O32-) in the solution hinders the passivation that was formed during the immersion of Zn alloys between 120h and 288h at 80°C in the absence of thiosulfate. Thiosulfate effect promotes Cl- penetration for not …

Augmented Reality Integrated Welder Training For Mechanical Engineering Technology, Aditya Akundi, Hamid Eisazadeh, Mona Torabizadeh

Engineering Technology Faculty Publications

The shortage of welders is well documented and projected to become more severe for various industries such as shipbuilding in coming years. It is mainly because welding training is a critical and often costly endeavor. This study examines the training potential using augmented reality technology as a critical part of welder training for mechanical engineering technology students. This study assessed the performance of two groups of MET students trained with two different methods. One group received training with the traditional method in three sessions. The second group acquired training initially with an augmented reality welding system for three sessions. Then, …

Method For Reducing Warping Stresses In Torsionally Loaded I-Section Members Using Cfrp Plates, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents a method for reducing warping normal stresses in torsionally loaded I-section members by utilizing carbon fiber-reinforced polymer (CFRP) plates. The CFRP plates are bonded to the outer surfaces of the flanges with a view to reducing warping normal stresses. The maximum warping normal stress in the flanges of a steel I-shaped member without the CFRP plates is compared to those obtained with the CFRP plates having various thicknesses. It has been found that the use of CFRP plates bonded to both flanges of the I-section result in a substantial reduction of the warping stresses. For the study …

Crystalline Analysis Of Geomicrobially-Induced Calcium Carbonate Precipitation In Sands Using A Surface Percolation Treatment Technique, Justin Edward Mulloney

UNF Graduate Theses and Dissertations

Ottawa 50/70 sand specimens and natural beach sand samples were treated using bio-augmented geomicrobies via a surface percolation technique. Testing was conducted on these specimens to determine how resultant calcium carbonate precipitation changed as a function of temperature, depth from the surface, and in the presence of magnesium. Specifically, x-ray Diffraction (XRD), a Scanning Electron Microscope (SEM), and Energy Dispersive X-ray Spectroscopy (EDS) were used to determine and quantify the presence of calcium carbonate and its associated phase. Results showed a direct relationship between temperature and precipitated calcium carbonate. In addition, as an unintended consequence associated with the treatment, ammonium …

Histological Comparison Of Shark Dermis Across Various Ecomorphologies, Olivia Schuitema

UNF Graduate Theses and Dissertations

The integument plays essential roles in the structural support, protection, and hydrodynamic capability among fishes. Most shark skin research has been done on the external epidermal layer containing the dermal denticles, while the larger dermis layer has been mostly ignored. The dermis layer in sharks is composed of two layers, the upper stratum laxum and the lower stratum compactum, holding supportive collagen and elastin fibers. There may be morphological and compositional differences in the dermis layers across various species of sharks, although the extent of such is unknown. These potential differences may be represented by various dermal thicknesses and different …

An Approach For Material Model Identification Of A Composite Coating Using Micro-Indentation And Multi-Scale Simulations, Pouya Shojaei, Riccardo Scazzosi, Mohamed Trabia, Brendan O’Toole, Marco Giglio, Xing Zhang, Yiliang Liao, Andrea Manes

Mechanical Engineering Faculty Research

While deposited thin film coatings can help enhance surface characteristics such as hardness and friction, their effective incorporation in product design is restricted by the limited understand-ing of their mechanical behavior. To address this, an approach combining micro-indentation and meso/micro-scale simulations was proposed. In this approach, micro-indentation testing was conducted on both the coating and the substrate. A meso-scale uniaxial compression finite element model was developed to obtain a material model of the coating. This material model was incorporated within an axisymmetric micro-scale model of the coating to simulate the indentation. The proposed approach was applied to a Ti/SiC metal …

Effect Of Freestream Noise On Hypersonic Crossflow-Induced Boundary-Layer Transition, Andrew Bustard, Thomas J. Juliano, Harrison B. Yates, Mark Noftz, Joseph Jewell

Publications

Between the windward and leeward rays, boundary-layer transition on cones at angle of attack in hypersonic flow is dominated by the crossflow instability [1, 2], wherein stationary and/or traveling crossflow vortices develop and can breakdown into turbulence [3]. Stationary crossflow modes are caused by surface roughness or any other steady forcing and produce disturbances that are fixed in place on the surface [3–6]. Stationary vortices create a generalized inflection point in the velocity profile that is inviscidly unstable [7]. This distorted mean flow develops secondary instabilities, whose growth and breakdown is one path to turbulence [8–10]. Traveling crossflow modes are …

An Electrochemical-Mechanical Investigation Of Next Generation Lithium Metal Electrode And Solid Electrolyte, Andrew Meyer

Theses and Dissertations--Chemical and Materials Engineering

Lithium-ion batteries (LIBs) are a staple in today’s society. From our cellphones, laptops, power tools, the ever-growing electric vehicle, and many more application, LIBs are more important to us than most realize. They provide the best combination of both high-energy and high-power density compared to other battery types such as Ni-Cd, Ni-MH, or the lead acid batteries used in our cars. Plus, LIBs are much safer. However, as new technologies grow and are developed, the demand for higher energy and power density, better safety, lower costs, and longer life increases. One way to achieve the ever-increasing demands is to replace …

Improving Manufacturing Processes For Making Lithium Ion Battery Electrodes, Ming Wang

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable lithium-ion batteries (LIBs) are widely used to provide energy and power in portable electronics, electric vehicles, and energy storage systems. The LIB market has grown dramatically as they have a combination of high energy density, high power density, proven reliability, and long cycle life. The manufacturing process is one of the key factors as it strongly affects the cost and performance of LIBs.

This dissertation is focused firstly on the development of a conventional slurry-based electrode manufacturing process. Slurry making is a critical step that affects the subsequent steps in battery manufacturing. In this work, we have investigated the …

Microscale Contact And Friction Of Low Modulus, Lightly Crosslinked Polydimethylsiloxane, Justin Glover

Theses and Dissertations--Chemical and Materials Engineering

Friction and adhesion of soft materials are important for pressure sensitive adhesives, biomaterials, and soft robotics; however, the behavior on the microscale is not fully understood. When two objects come into contact, their interactions are usually mediated by small contact points due to surface roughness. At the microscale size, surface forces can deform soft materials to minimize energy by increasing the contact area, which is balanced by the elastic deformation of the polymer network. However, for soft, crosslinked materials with a modulus below ~100 kPa, it is challenging to predict the behavior with prior contact and friction models. Additionally, lightly …

Derivation, Exploration And Evaluation Of Non-Equiatomic High Entropy Alloys, Artashes Ter-Isahakyan

Theses and Dissertations--Chemical and Materials Engineering

High-entropy alloys (HEAs) are a class of multicomponent alloys based on an innovative alloying strategy that employs multi-principle elements in relatively high concentrations. Commonly defined as alloys that contain at least five principal elements, each with a concentration between 5 and 35 at %. The term entropy refers to the excess configurational entropy associated with HEAs, which is thought to facilitate the formation of solid solutions. The design strategy results in vast compositional space for exploration and innovative potential triggering a renaissance in physical metallurgy. These alloys may have favorable properties compared to conventional dilute solid solutions, but their preeminent …

Optimize The Niu Split Hopkinson Pressure Bar Apparatus For Conducting High Strain Rate Tensile Test On S304 Foils, Jiale Ji

Graduate Research Theses & Dissertations

Split Hopkinson Bar (SHB) methods are widely used to experimentally characterize the mechanical properties of materials such as metals, concrete, and ceramics undergoing rapid deformation. NIU had a split-Hopkinson tensile apparatus that can conduct coarse tensile test, but it can’t output the useful signal. The aim of this thesis is to optimize the existing apparatus, so the high strain rate tensile tests for the stainless steel 304 can be conducted and useful signal can be got. The alignment of the bars is critical for a good signal that has less noise. To eliminate the noise signal, some accurate fixture is …

Warm Unit Stand Analysis For Proton Improvement Project Ii, Michael William Pavlick

Graduate Research Theses & Dissertations

The Proton Improvement Project II, commonly referred to as PIP II, is a linear accelerator overhaul at Fermilab to eventually double the output of its existing proton beam to continue to be the leading force in high energy physics. The proton beam is created through a series of high frequency cryomodules that must be connected utilizing a combination of magnets and vacuum pumps to ensure the beam is properly aligned. A housing mechanism for the magnets and vacuum pumps (Warm Units) will be placed between the cryomodules for realignment and require multiple stages of 6 degree-of-freedom adjustment options, to ensure …

An Archimedes' Screw For Light, Emanuele Galiffi, Paloma A. Huidobro, J. B. Pendry

Advanced Science Research Center

An Archimedes’ Screw captures water, feeding energy into it by lifting it to a higher level. We introduce the first instance of an optical Archimedes’ Screw, and demonstrate how this system is capable of capturing light, dragging it and amplifying it. We unveil new exact analytic solutions to Maxwell’s Equations for a wide family of chiral space-time media, and show their potential to achieve chirally selective amplification within widely tunable parity-time-broken phases. Our work, which may be readily implemented via pump-probe experiments with circularly polarized beams, opens a new direction in the physics of time-varying media by merging the rising …