Engineering Commons^™

Determination Of Manufacturing Parameters Of Large Section Of Continuous Steel Box Beam With Variable Section In Shenzhen‑Zhongshan Passage, Dong Chuangwen, Chen Long, Li Chuanxi

Journal of China & Foreign Highway

Accurate calculation of manufacturing parameters is the key to the efficient，high-precision，and rapid installation of large sections of continuous steel box beam bridges.Taking the steel box beam with the variable section in Shenzhen-Zhongshan Passage as the background，this paper first established a finite element model of the beam element in the whole construction process to obtain the pre-camper.Secondly，the average neutral axis position was calculated based on the height of the neutral axis of each beam section.Then，according to the deformation characteristic that the beam length remained unchanged at the mean neutral axis，the pre-camber was superimposed at the mean neutral axis to get the …

Key Technology For Construction Of New Single‑Wall Steel Suspended Box Cofferdam With High Pile Tied Beams In Deep Water, Yang Jinlong, Zhao Lin, Jiang Qunlong

Journal of China & Foreign Highway

In order to ensure the safe，efficient，and economical completion of the construction of the high pile tied beam of Muping Xiangjiang River Bridge in deep water，a new type of single-wall steel suspended box cofferdam was designed to act as the water retaining and enclosure structure during high pile tied beam construction according to the characteristics of deep water level and shallow stratum cover layer at the high pile tied beam location.Through the innovative design of steel casing on the bottom of the steel suspended box cofferdam，the design height of the wall panel and the amount of steel input were reduced.On the …

Influence Factors Of Carbonization Of Tunnel Segment Structure And Life Prediction Analysis, Li Dongbiao, Miao Miao, Shen Caihua, Chen Wei

Journal of China & Foreign Highway

There are many factors that affect the carbonization life of concrete segments in underwater tunnels，and the prediction methods are not uniform.In this paper，combined with actual engineering，the influencing factors and laws of carbonization of concrete segments in underwater tunnels were analyzed，and three methods for predicting the life of concrete segments were established with the crack limit as the control target.The prediction results of the three methods were compared.The results show that the influence of the temperature and CO2 concentration in the tunnel predicted by the three methods on the life of the tunnel lining structure is basically consistent with the existing …

Key Technology For Incremental Launching Construction Of Double Guide Beam Of Steel Box Girder, Sun Xiaoqiang, Yue Xinxing

Journal of China & Foreign Highway

By taking the incremental launching construction of the steel box girder at the 6th hole of the approach bridge of Baoji Taigu Bridge as the engineering background，the original plan adopted single-guide beam multi-point walking incremental launching technology for assembly and incremental launching on the prestressed reinforced concrete beam of the adjacent hole.Since the middle span of the concrete beam cannot withstand the concentrated force at the incremental launching points，the multi-guide beam multi-point walking incremental launching technology was finally used to arrange the incremental launching points at the transverse diaphragm plate of the end of the concrete beam.By increasing the incremental …

Emergency Vehicle Dispatching Model Considering Demand Urgency And Delivery Fairness, Long Kejun, Liu Jia, Gao Zhibo, Chen Suqian, Zhang Zhonggen

Journal of China & Foreign Highway

In emergency vehicle dispatching after unexpected events，it is crucial to prioritize critical nodes with high demand urgency while minimizing excessive delivery delays at other nodes to prevent secondary impacts.On this basis，this study developed an emergency vehicle dispatching model that considered demand urgency and delivery delay fairness.Firstly，the entropy weight-TOPSIS method was used to calculate the demand urgency for each node，and a delivery delay balance index was introduced to minimize disparities in delivery delays between nodes.Secondly，a multi-objective optimization model was established with total delivery time，overall cost，and delivery delay balance as objectives，while considering constraints such as inventory levels at distribution centers and route …

Working Properties Of Steel Tube Batter Piles With Concrete Infill Based On Abaqus, Yang Meiliang, Li Liemin, Sun Kunjiang, Han Rui, Zhong Yang

Journal of China & Foreign Highway

In order to explore the respons e characteristics of steel tube batter piles with concrete infill under vertical load，the steel tube batter pile with concrete infill used in Saribas Bridge in Malaysia was taken as the research object.Based on the numerical simulation method，the frictional resistance of the inner and outer walls of the steel tube，the frictional resistance around the pile at the section，and the bending moment bearing ratio between the steel tube and the concrete core of this type of batter pile under vertical load were studied.The results show that the passive-side frictional resistance of the 0–15 m pile section …

Synthesis Of Activated Carbon From Coconut Shell And Recycled Styrofoam Nanofiber For Water Filtration, Rahma Dani, Ismet Ismet, Leni Marlina, Rona Alisya, Muhamad Abel Kirana Aldi, Anggi Ludiansyah, Lintang Auliya Kurdiati, Meutia Kamilatun Nuha Ap Idjan, Agung Mataram, Muhammad Rama Almafie, Ida Sriyanti

Makara Journal of Science

Water pollution affects life sustainability; hence, several efforts have been exerted to overcome this problem. For ex-ample, nanofiber membrane technology is introduced to retain solutes while allowing only water molecules to pass through the system. Therefore, this study aimed to maximize the technology for water filtration using the electrospin-ning method by combining Styrofoam waste-based polymer with activated carbon from coconut shell waste (ACCS). The nanofiber diameter produced ranged from 590 nm to 610 nm with porous characteristics and without beads. The carbon content varied from 68.04% to 69.84%, according to the energy dispersive X-ray measurement, demonstrating the composite’s effectiveness. The …

A Mechanistic Study Of Silicon Nanocrystal Formation Via Solid State Synthesis, Katherine Mccarthy Weinfurter

Dissertations and Theses

Silicon nanocrystals (SiNCs) show promising physiochemical properties that could be used in industrial applications. The production of SiNCs through solid-state synthesis is ideal due to relatively low cost of equipment and chemical reagents, as well as the ability to scale-up production. A widely known and commonly used precursor previously used in solid-state synthesis for SiNCs, hydrogen silsesquioxane (HSiO_1.5), was discontinued in chemical manufacturing, which has led to researching alternative precursors (or starting materials). We have identified that there is a gap of knowledge related to producing these precursors, as well as the mechanistic understanding of the chemical reactions …

Zeolite 13x Particles With Porous Tio2 Coating And Ag2o Nanoparticles As Multi-Functional Filler Materials For Face Masks, Wei Su, Kaiying Wang, Han Yu, Fateme Fayyazbakhsh, Jeremy Watts, Yue-Wern Huang, Jee-Ching Wang, Xinhua Liang

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Adsorbent components in face masks are crucial for protecting individuals exposed to dangerous situations. In this study, one porous TiO₂ layer was deposited on zeolite 13X particles by coating hybrid organic/inorganic titanium alkoxide film via molecular layer deposition (MLD), followed by heat treatment to remove organic components in the MLD film. Various concentrations of Ag₂O nanoparticles were impregnated on the TiO₂-coated 13X particles, offering a wide range of antibacterial, antifungal, and antiviral characteristics. The obtained composite particles were characterized using X-ray photoelectron spectroscopy and thermal gravimetric analysis to study the composition and mass loading of …

Surface Chemistry And Adsorption Mechanism Of Orfom® D8 For Cu Depression In Cu-Mo Flotation, Patrick Jeff Mensah

Graduate Theses & Non-Theses

In traditional chalcopyrite-molybdenite (Cu-Mo) flotation separation systems, inorganic depressants such as NaSH and NaCN are used to selectively depress chalcopyrite making it more hydrophilic so molybdenite can be floated and recovered. NaSH and NaCN are highly toxic, have high explosion potential, strong odor, and readily oxidize in air resulting in a high consumption rates. To control oxidation, nitrogen gas, and Nokes reagent are both necessary, making the process even more expensive. In addressing these challenges, attention is fast shifting to disodium carboxymethyl trithiocarbonate (Orfom® D8), a novel organic depressant designed to replace conventional inorganic depressants because it does not easily …

Lignin Cationization For The Removal Of Phosphates And Nitrates From Effluents Of Wastewater Treatment Plants, Fannyuy V. Kewir

LSU Master's Theses

The removal of phosphates and nitrates from wastewater treatment plant (WWTP) effluents is important for preventing pollution of receiving waters. In this study, we chemically modified alkaline lignin (aLN) with quaternary ammonium groups to obtain biodegradable cationic lignin (cLN). We characterized the cLN and tested its efficacy for removing phosphates and nitrates in a lab setting and on field-collected WWTP samples. Adsorption isotherm and kinetic studies were performed in aqueous media, and the effects of several variables (contact time, pH, initial concentration, and adsorbent dose) were investigated. The Langmuir isotherm described phosphate and nitrate adsorption well, with R2 values of …

Ge/Sige Quantum Wells: Material For The Post-Moore Era, Troy Alexander Hutchins-Delgado

Optical Science and Engineering ETDs

This dissertation demonstrates high-quality germanium quantum wells on a 200 mm silicon wafer platform, enabling novel device possibilities. Partnering with a commercial silicon-germanium epitaxy supplier, we obtained shallow, undoped germanium quantum wells with high-crystalline quality, confirmed through x-ray diffraction, secondary ion mass spectroscopy, high-resolution scanning transmission electron microscopy, and energy dispersive x-ray spectroscopy. Hall bar devices fabricated on single quantum wells revealed that surface preparation can tune transport properties while maintaining peak mobilities around 10⁵ cm²V⁻¹s⁻¹. Manganese-germanide spintronic contacts were integrated via solid-state reaction, with contact quality assessed through Schottky diodes, transfer length …

Nature-Derived Flame Retardant For Cotton Fabrics With Green Coconut Shells, Tarikul Islam, Abdullah Al Rakib Shikder, Md Shahabul Hossen, Md Mazbah Uddin, Md Tanvir Hossain, M. Mahbubul Bashar

Michigan Tech Publications

This study presents an eco-friendly flame-retardant solution for cellulosic fabrics using green coconut shell (GCS) extract and phytic acid (PA). Cellulosic materials are highly flammable and release harmful gases during combustion. Conventional flame retardants may pose environmental and health risks while impacting the fabric quality. GCS extract is a rich source of tannins, phosphorus, silicates, metallic salts, and oxides and is explored as a novel flame retardant (FR) for cotton fabrics. Cotton samples were pretreated with PA and then with varying concentrations of GCS extract using a padding technique. Comprehensive characterization followed, including limiting oxygen index (LOI), thermogravimetric analysis (TGA), …

Using Additive Manufacturing To Characterize Effects Of Sparse Infill Density And Sparse Infill Pattern On The Compressive Properties Of Short Strand Carbon Fiber Infused Petg, Luke C. Salisbury

Honors Theses

The advent of additive manufacturing has revolutionized the prototyping, design, and manufacturing of new and innovative products. Through the use of Fused Deposition Modeling (FDM), parts can be manufactured using different sparse infill percentages (the percentage of void space within a printed object) and sparse infill patterns (the lattice structure of material within the object). Through the manipulation of these variables, the same material and part can have different compressive and flexural properties. In addition to sparse infill, the thermoplastics used in fused deposition modeling can be reinforced with carbon fiber strands to create a printable composite material capable of …

Complex Precipitation Behavior In A Co-Free High Entropy Alloy During Aging, Matthew Luebbe, Fan Zhang, Jonathan D. Poplawsky, Jiaqi Duan, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

High entropy alloys (HEAs) demonstrate high strength, thermal stability, and irradiation resistance, making them desirable for applications in nuclear reactors and other harsh environments. Many existing HEAs contain cobalt (Co), which makes them unsuitable for nuclear applications due to the long-term activation of Co. A previously studied Co-free alloy, (Fe_0.3Ni_0.3Mn_0.3Cr_0.1)₈₈Ti₄Al₈, exhibits high strength but compromised ductility due to its network of brittle precipitates upon aging. This work investigates the formation mechanism and evolution of the precipitates, including L1₂ (Ni₃Ti type, ordered face-centered cubic …

Synthesis And Doping Effects In Highly Conductive Chalcogenide Solid Electrolytes., Selim Halacoglu

Electronic Theses and Dissertations

Lithium and sodium ion batteries have been a vital component in the growth of small, portable electronic devices and EVs over the past 30 years. For future energy needs, changes to battery chemistry and composition will be necessary for two primary reasons: safer and higher energy batteries. Metal anodes have not seen widespread commercialization because of their propensity to react aggressively with the flammable liquid electrolytes commonly used in modern batteries. Non-flammable solid-state batteries (SSB) with solid electrolytes can safely be used with metal anodes, potentially providing a solution to both problems. The future perspective of safer battery is that …

High Energy Density Lithium-Ion Battery Materials., Rachel Dewees

Electronic Theses and Dissertations

Growth of the EV industry has created an increased demand for Li-ion battery electrode materials, and support of a robust lithium-ion battery supply chain is a national imperative. For mainstream acceptance in the American market, the range of EVs must be improved, i.e., the energy density of the battery must be increased. Increasing the specific capacity of the electrode materials is the most direct strategy for increasing the energy density of the battery. Silicon anode materials have a theoretical capacity of over 3700 mAh·g^-1 - an order of magnitude beyond that of the graphitic materials which are currently implemented. …

Striking A Balance: Market Shock & Responses In Automotive Components Manufacturing, Emma Lane Mcgahey

All Theses

This thesis examines the effects of extreme market shocks on supply chain dynamics within the automotive industry. Through an analysis of demand data from an automotive manufacturer to its component suppliers (January 2018 to May 2024), the study investigates the relationship between market shocks and supply chain responses, providing insights into how auto components inventory management handles downstream responses to market shocks. With supporting public data—from FRED, BLS, and the U.S. Census Bureau resources—we explore two primary relationships: the impact of market shocks on the Average Standard Deviation of Demand (SDO) and the effect of demand variability on expedited pricing …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-Based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO₂, MoS₂, and Al₂O₃) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment …

Pressureless Sintering Of Sic - Oxide Multiphase Ceramics For Protective Coating Applications, Reilly Boros

All Theses

For hydrogen-fueled combustion, there exists a demand to improve coating materials that are capable of protecting SiC_f/SiC CMC turbine material. Promising coating materials must be able to shield from harsh oxidation while working at extremely high temperatures. The work presented in this thesis aims to expand the understanding of two promising material systems for integrated environmental barrier coating (EBC) – thermal barrier coatings (TBC) by fabricating bulk composite ceramic samples and performing characterization to further understand their sintering behaviors. In this study, a processing procedure to consistently produce dense composite ceramics of PDC SiC – Y₂Si …

Toward Electrochemical Detection Of Salmonella Enterica Serovar Enteritidis On Hydroponically Grown Green Onions (Allium Fistulosum L.), Lisseth Casso-Hartmann

All Theses

The Food and Drug Administration (FDA) established standards during the growing, harvesting, packing, and holding of produce for human consumption as part of implementing the Food Safety Modernization Act (FSMA). One of the main requirements for farmers is to detect environmental pathogens such as Salmonella enterica species in water and sprout samples. S. enterica is a bacterium of significant concern due to its pathogenicity and ability to survive and persist in diverse environmental conditions. S. enterica has been associated with recalls in ready-to-eat foods. Traditional detection methods include Enzyme-Linked Immunosorbent Assay (ELISA), Polymerase Chain Reaction (PCR), and plate counting, which …

Ellipticity-Controlled Exceptional Points From Nanoscale Metasurfaces, Benjamin Goldberg

McKelvey School of Engineering Graduate Student Theses & Dissertations

Precise control over light polarization is critical for advancing technologies in telecommunica- tions, quantum computing, and image sensing. However, existing methods for manipulating polarization around exceptional points in non-Hermitian systems, have exclusively focused on circular polarization and work with reflected light. To address this limitation, we de- velop a novel metasurface platform with high-Q resonators that enables tunable control of polarization exceptional points across arbitrary ellipticity for transmitted light. Our design uses orthogonally polarized guided mode resonators in a two-layer silicon metasurface, where careful tuning of the dipolar guided mode resonances (DGMRs) and layer spacing allows us to control the …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

Removal Capabilities Of Zeolite And Zero Valent Iron With High-Level Waste Tank Radionuclides And Metals: Cesium, Strontium And Chromium, Colette R. Towles

UNLV Theses, Dissertations, Professional Papers, and Capstones

High level nuclear waste (HLW) has been disposed for temporary storage in underground steel tanks at the Department of Energy Nuclear sites. For example, at the Hanford Site, WA, and Savannah River Site (SRS), SC, HLW account for eighty-eight million gallons (Mgal) and 450 million Curies (MCi) of radioactivity. In the early nuclear activity at Hanford, the waste was discharged to single-shell steel tanks, and the lack of secondary containment allowed leaks, contaminating soil and groundwater. Despite tremendous efforts to stabilize the liquid waste at nuclear sites, treatment is complex, costly, and time-consuming; therefore, HLW may have to be stored …

Density-Driven Investigations Of Ruthenium Binary Compounds Rux2 (X = O, S, N), Melanie White

UNLV Theses, Dissertations, Professional Papers, and Capstones

Exploration and fine-tuning of the energy landscape of materials can be accessed by means of changes in material density, a key principle of high pressure research. Density-driven changes impact variations in oxidation states and coordination numbers for the element constituents of a compound. Pressure-induced modification of intrinsic density can promote the formation of new materials, variations in physical properties, and transformations in crystallographic symmetry. With this as our foundation, we focus on ruthenium binary compounds - altering the anion species to change electronegativity while probing pressure and temperature effects. This led us to the present study of ruthenium oxide RuO2, …

Influence Of Glycopolymer Structure On Amphiphilic, Hybrid, Linear Branched Block Copolymer Properties For Use In Biomedical Applications, Kevin Green

Dissertations

The focus of this dissertation is evaluating and adding fundamental knowledge regarding the structure-property relations of glycopolymers used in the design of hybrid block copolymers (HBC) that are cable of self-assembling into delivery vehicles for biomedical applications. A shift to the utilization of natural materials in the design and fabrication of drug-delivery vehicles has garnered significant attention. Understanding the effects of linear glycopolymers content and composition on the resulting HBCs properties can provide valuable insight into how these materials may be tailored for use in targeted biological applications.

The first chapter introduces current literature on the need for improvement in …

Neural Operator And Physics-Informed Deep Learning Approaches For Inverse Design Of Composites And Manufacturing Processes, Minglei Lu

All Dissertations

In this dissertation, artificial intelligence (AI) models are designed and used to accelerate inverse design of composites and manufacturing processes. The critical bottlenecks in machine learning (ML) including data availability, data quality, model generalization and adaptation, interpretability, physical consistency, and the ’black box’ nature of models for the inverse design are addressed. And the proposed AI models are tested under different engineering scenarios. Firstly, a fast deep neural operator (DNO) structure was developed to significantly reduce training time. This model was tested in the context of additive manufacturing, a transformative industrial technology that allows for the creation of materials with …

Investigation Of Conductive Die-Top Thermal Capacitors During Short Circuit Operation Of Silicon Carbide Devices, Youssef Abotaleb

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) power devices have garnered significant attention in recent years due to their superior thermal and electrical properties compared to traditional silicon devices. However, SiC power devices suffer from severe reliability issues arising from their mechanical properties. This is because the Young's modulus of SiC is about three times larger than that of silicon, which correspondingly raises the mechanical stresses acting on the bonding structure, often leading to device failure under power shock events.

Traditional packaging materials and designs tend to constrain SiC performance, as hot-spot temperature resulting from a power shock is one of the key factors …

Understanding Defect Dynamics In Black Phosphorene Under Noble Gas Ion Irradiation., Saransh Gupta

Electronic Theses and Dissertations

Controlled introduction of defects in phosphorene using high-energy ion beams offers a promising route to design novel high-performance materials for energy technologies. However, this potential remains underexplored due to a lack of fundamental understanding of the atomic-scale mechanisms governing the production, accumulation, and temporal evolution of defects during ion irradiation. Here, we employ a combination of classical and ab initio molecular dynamics simulations to elucidate the effects of ion energy, angle of incidence, noble gas ion size/mass, and fluence on (a) defect generation (i.e., point defects, topological imperfections, voids), (b) atomic-scale mechanisms of defect formation and re-arrangement, and (c) defect …