Engineering Commons^™

Desirable Combinations Of Electrode And Flux For Submerged Arc Welding Of Low Carbon Steel, James A. Husmann

Graduate Research Papers

The major purpose of this study was to provide information about desirable combinations of welding electrode and appropriate fluxes for submerged arc welding of low carbon steel. Other purposes were to:

1. Test a variety of combinations of available submerged arc welding electrodes and fluxes in welding low carbon steel.

a. Prepare specimens for tensile tests.

b. Conduct tensile tests.

c. Calculate tensile strength, yield point, break point, percent of elongation, and percent reduction of area.

2. Determine the most desirable combinations of electrode and flux for companies presently using or planning to use submerged arc welding for low carbon …

Accelerated Curing Test Of Cement, Amr Ali Ibrahim

Archived Theses and Dissertations

No abstract provided.

Closed Water Systems On Paper And Board Machines Using The Dysco Simulation Program, Stephen Robert Tremont

Masters Theses

This study was conducted to determine the accuracy of the DYSCO simulation program in simulating the open and closed water system on the pilot fourdrinier paper machine located in the Department of Paper Science and Engineering at Western Michigan University. The pilot machine was run at a maximum speed of 76 meters (250 feet) per minute without the press and drier sections, as well as slower speeds of 61 and 46 meters per minute. Retention data were obtained for fiber, titanium dioxide, and water at the three speeds. Upon entering these data along with stream inputs into the DYSCO simulator, …

Factors Influencing The Production Rate And Quality Of Lead Sinter, John R. Knoepke, Hung Yang Tsai, Arthur E. Morris

Materials Science and Engineering Faculty Research & Creative Works

The sintering characteristics of a typical Missouri lead concentrate were determined for two types of raw sinter mix: conventionally prepared and pelletized. The important sintering characteristics are sulfur elimination, sinter strength, production rate of sinter, permeability of the sinter bed, and bed temperature. These characteristics were analyzed statistically, and are described by an empirical model, in which proportion of returns, moisture content, air flow, bed height, size distribution of returns, and ignition time are the independent variables. The characteristics of a conventionally prepared sinter mix are most strongly affected by the moisture content of the raw mix. The characteristics of …

Metal Cation/Anion Speciation Via Paired-Ion, Reversed Phase Hplc With Refractive Index And/Or Inductively Coupled Plasma Emission Spectroscopic Detection Methods, Richard N. Savage, D. Bushee, I. S. Krull, S. B. Smith, Jr.

Materials Engineering

Conventional high performance liquid chromatography instrumentation and packing materials can be inexpensively and rapidly utilized for the qualitative and quantitative analysis of various metal cations or anions. The final approaches utilize reversed phase HPLC in the form of paired-ion separations. The detection of individually eluted, fully resolved metal cations or anions is possible via conventional refractive index or inductively coupled plasma emission spectroscopic detection. In many cases, unresolved mixtures of metal cations, eluted as a single peak on HPLC, can be resolved and identified via the use of ICP detection. Both metal cations and anions can be easily resolved, according …

Plastic Deformation And Fracture Of Binary And Ternary Aluminum Alloys Under Compressive Loading, Samir Mokhtar Biblawi

Archived Theses and Dissertations

No abstract provided.

Chemical Corrosion Of Ag Films On Glass, Hyun Soo Park

Doctoral Dissertations

"The chemical corrosion of chemically, vacuum and sputter deposited Ag films on an aluminoborosilicate and a soda lime glass was investigated in wet HCl and saturated water vapor as a function of concentration, temperature and time. The higher corrosion resistance of chemically deposited Ag films in comparison to evaporated or sputtered Ag films is attributed to their lower microvoid density and higher adhesion strength. Ag films on the more chemically durable aluminoborosilicate glass had a higher corrosion resistance. Furthermore, films which received a moderate thermal annealing (80 to 140° C) or were deposited on a glass surface washed with HN0 …

Effects Of Varying Oxygen Partial Pressure On Molten Silicon-Ceramic Substrate Interactions, And Oxygen Partial Pressure Measurements Of Silicon Sheet Production Facilities, P. D. Ownby, Harold V. Romero

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Measurement Of The Wear Properties Of Metallic Solids With A Falex Lubricant Testing Machine, Edward Boyd Hale, Chun-Ping John Meng, Ronald A. Kohser

Physics Faculty Research & Creative Works

A modified Falex Lubricant Testing Machine has been used to determine wear properties of metallic solids. In particular, wear mass loss, wear volume loss, wear rates, and other parameters have been determined for a basic steel, as heat treated and after ion implantation. Wear rate improvements of more than an order of magnitude were found in a nickel-chrome steel (SAE 3135) implanted with 2.5x10¹⁷ N⁺₂/cm². Wear tests were conducted with a cylinder-in-groove geometry in a mild lubricating oil with loads greater than 540 N, which corresponded to pressures which exceeded 10⁸N/m^{2 …}

Phaseautomodulation In Magnesium, Alexander Aning, Tetsuro Suzuki, Manfred Wuttig

Physics Faculty Research & Creative Works

No abstract provided.

Measurement Of Neck Development In Tensile Testing Using Projection Moire, Raghavan Srinivasan, C. S. Hartley, C. Raju, J. Clave

Mechanical and Materials Engineering Faculty Publications

The projection moire technique affords an accurate method of measuring the geometry of the necked region in a tensile specimen. Corrections to the measured stress, necessary to account for the triaxiality introduced by the neck, require values for the radius of curvature of the specimen at the minimum section. The spacing of fringes resulting from the interference between a grating projected on the specimen surface and a master grating not only provide information which permits calculation of the radius but also demonstrates any changes in symmetry resulting from plastic deformation. Results obtained by testing specimens of copper and mild steel …

Drawing Characteristics Of Electrogalvanized Steel Wires., Chi-Yuan Tsao

Masters Theses

"As a means of investigating the often adverse drawing behavior of electrogalvanized steel wire, drawing experiments were conducted on a variety of industrially-supplied and laboratory-prepared electroplated steel wires. Back-flow and shaving appeared to be the mechanisms by which sizeable zinc losses occurred. Performance during drawing and the quality of the product depended upon both the characteristics of the plating and the drawing process variables. Grain size, grain texture, and surface 'flatness' can affect the required drawing force, surface finish and level of zinc retention. Low die angles and large reductions offered greatest efficiencies with minimum zinc loss"--Abstract p. ii

Sessile Drop Studies Of Gallium On Alumina, Timothy John Snyder

Masters Theses

"The liquid-vapor and solid-vapor interfacial energies of the system Ga-Al₂O₃ were determined by the sessile drop technique. The interfacial energies were found to decrease with increasing temperature and P₀₂.

A maximum liquid-vapor interfacial energy of 581 ergs/cm² was found for a clean sessile drop at 1227°C. Values for Γ₀, the excess concentration of oxygen, were calculated for both the liquid-vapor and solid-liquid interfaces. The work of adhesion between molten Ga and Al₂O₃ was found to increase with decreasing P₀₂ with a maximum of 576 ergs/cm² occurring …

The Influence Of Manganese Oxide On Sintering Of A Commercial Natural Magnesite., Alamar Kasan Duarte

Masters Theses

"Sintering studies on a commercial natural magnesite have been done to investigate the influence of MnO doping (MnO concentration from 0.16 to 2.50 wt.%) on the densification process over the temperature range 1520 to 1760°C , over periods of time from 3,600 to 57,600s in both oxidizing and reducing atmospheres (Air and P_O2 = 10^-7 KPa. In an air atmosphere the additions of MnO enhances the densification process. This fact may be associated with an increase in lattice diffusion of Mg ions due to an increase in cation vacancies in the MgO lattice from the presence of …

Stability And Properties Of Products Made From Splat Cooled Aluminium Base Alloys, Soheir Ahmed Azab

Archived Theses and Dissertations

No abstract provided.

Galling Characteristics Of Aluminum Alloys, Magdy Mohamed Hussein Ahmed Shoukry

Archived Theses and Dissertations

No abstract provided.

Glass Surfaces Then And Now, Norbert J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

A reservoir of efficient instrumentation capable of detailed and quantitative exploration of glass surface features is now available in the face of the recognition of their crucial importance for both surface and bulk properties as well as performance. Yet it may be instructive to glance at what had been learned about glass surfaces by investigators before the advent of these intricate tools. Among such earlier findings are the recognition of the altered composition and structure of the surface layer, the extension of this disturbance to considerable depth, the effect of surface structure on adsorption, adhesion, wetting, finishing, etc. and on …

Anomalous Diffusion Of Carbon In A 70/30 Iron-Nickel Alloy, L. R. Chapman, D. A. Powers, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Seeded Oscillatory Growth Of Si Over Sio² By Cw Laser Irradiation, G.K. Celler, L. E. Trimble, K.K. Ng, H.J. Leamy, H. Baumgart

Electrical & Computer Engineering Faculty Publications

Extensive seeded epitaxial growth of crystalline Si over SiO₂ was achieved by an oscillatory regrowth method applied to rectangular Si pads recessed into a thick SiO₂ film. Narrow (≃5 μm) via holes linked the pads with the bulk (100) Si substrate. Oriented single crystals propagated as far as 500 μm from the seeding area, following the long term advance of a scanned focused laser beam.

Silicon As A Millimeter-Wave Monolithically Integrated Substrate - A New Look, Arye Rosen, Martin Caulton, Anna M. Gombar, Walter M. Janton, Chung P. Wu, John F. Corboy, Charles W. Magee

Henry M. Rowan College of Engineering Departmental Research

Materials suitable for use as monolithic substrates are summarized. A study of the properties of silicon substrates as transmission line media shows that serious consideration should be given to them for use at mm-wave frequencies. It is concluded that for silicon resistivities of 2000 ohm-cm or greater, microstrip loss in silicon at mm-wave frequencies is only slightly higher than that in GaAs or alumina. The cross section width of a transmission line represents an appreciable part of a wavelength when microstrip is used as an impedance transformer at mm-wave frequencies. Therefore, substrate thickness (using the latest dispersion characteristics) is especially …

Suitability Of Egyptian Raw Materials For The Production Of Cement Clinker Using The Dry Process, Lamia Rifaat Ismail

Archived Theses and Dissertations

No abstract provided.

Articles Molded From Papermill Sludge, Bruce A. Haataja, Anders E. Lund

Michigan Tech Patents

An article, such as a pallet having a substantially flat deck member and a plurality of hollow legs projecting from the deck member, is molded as a one-piece unit from a papermill sludge. Dried, comminuted papermill sludge is blended with a fibrous reinforcing material, preferably a cellulosic material such as fibrous bark particles, and a resinous particle board binder, the resulting mixture of furnish is formed into a loosely fitted mat, and the mat is placed between dyes of a mold and press and compressed to substantially the desired shape under temperature and pressure conditions sufficient to bond the sludge …

The Influence Of Halloysite Content On The Shear Strength Of Kaolinite, Reka Katalin Gabor

Dissertations and Theses

The objective of this thesis is to determine the relative shear strengths of halloysite, kaolinite, synthetic mixtures, and local soils, to investigate the influence of halloysite content on the shear strength of kaolinite, and to explore the possibility that the strength properties of soil clays might be controlled by the relative content of their component minerals.

Fingerling Shear, Tauno B. Kilpela, Bruce A. Haataja

Michigan Tech Patents

A fingerling shear for shearing a length of wood in a plane transverse to the grain direction and for splitting the sheared length along the grain direction to form a plurality of fingerlings. The shear includes a planar shearing blade, supported for rotation about a generally vertical axis, the planar shearing blade including an involute cutting edge adapted to engage the elongated piece of wood during rotation of the blade and for shearing off a length of that piece of wood, and a plurality of splitting blades fixed to the lower surface of the planar shearing blade and spaced along …

23rd Rocky Mountain Conference

Rocky Mountain Conference on Magnetic Resonance

Abstracts and meeting program from the 23rd annual meeting of the Rocky Mountain Conference, co-sponsored by the Rocky Mountain Section of the Society for Applied Spectroscopy and the Rocky Mountain Chromatography Discussion Group. Held in Denver, Colorado, August 2-6, 1981.

Conduction Polarization In Sodium Germanate Glasses, Akira Doi, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

Only one thermally stimulated depolarization current (TSDC) peak was found in germanate glasses containing from 0.19 to 32.5 mol% Na₂0, whereas comparable silicate glasses exhibit two such peaks. Equations are developed showing that the distortion of the equilibrium Na⁺-ion distribution by an applied electrical field produces a polarization in general agreement with the observed TSDC peak. It is proposed that the TSDC peak is due to dc conduction.

Synthesis And Evaluation Od Ashless Polymeric Lube Oil Addtives Containing Phosphorus, Sulphur And Nitrogen, Salwa Salah Nasr

Archived Theses and Dissertations

No abstract provided.

The Effect Of Adhesive Bond Strength Of Selected Species Of Laminated Wood, Daniel L. Henderson

Graduate Research Papers

Wood laminating has been used by man for centuries and is a very important part of industrial enterprises today. In most woodworking textbooks reviewed however, those sections devoted to wood laminating are typically miniscule. Topics are hastily covered and only general information is provided. This study has been conducted in order to provide more adequate explanation of the laminating process in addition to those presently available and to explore the interrelationship of laminated components with the ultimate function of the product. A glance at any furniture manufacturing or construction industry periodical, however, will show the importance of wood laminating in …

Computerized Twist Drill Selection For Cast Iron And Steel, Clinton K. Orth

Graduate Research Papers

The science of hole making can hardly be considered new to modern day industry. Evidence of drilling dates back as early as 4000 B.C. However, computers are considered relatively new to industry and their use is growing rapidly. One of the major concerns of industry is to identify a consistent method of selecting the proper drill when given a set of variables. The problem is to identify the sets of variables and select a drill that will give consistent results.

Development And Characterization Of A 9-Mm Inductively-Coupled Argon Plasma Source For Atomic Emission Spectrometry, A. D. Weiss, Richard N. Savage, G. M. Hieftje

Materials Engineering

A new 9-mm (i.d.) inductively-coupled plasma (ICP) torch is described which supports a stable, analytically useful plasma at less than 500 W of r.f. power and 7 l min^-1 total argon gas flow. Detection limits, working curves and other analytical characteristics of the new device are compared with those of both a miniature (13-mm i.d.) and conventional (19-mm i.d.) ICP. Although temperatures of the new plasma are somewhat lower than those in the larger plasmas, the new system offers promise for future, miniaturized ICP instruments.