Engineering Commons^™

Electrochemical Techniques For Measuring Anti-Corrosion Behavior Of The Thin Corrosion Inhibitor Layer To The 907a Steel, Yong-Tao Zhao, Jian-Hua Wu, Fan-Cai Chen, Zhong-Ping Gao, Jia Wang, Chang-Jiu Zhao

Journal of Electrochemistry

The corrosion inhibiting behavior of 907A steel, which was covered with thin inhibitor layers in moist seawater atmosphere,was studied. The electrochemical measurements, including EIS method and the coulostatic method, were used to atmospheric corrosioed monitor (ACM) under thin inhibitor layers to determine its corrosion rate. The results shown that the application of electrochemical methods such as the coulostatic technique and EIS could readily detect the on going process of film formation. Hence, the rapid evaluation of the thin inhibitor layers for 907A steel might be possible.

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi_0.8-xAl_xCo_0.2O₂ (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi_0.71Al_0.09Co_0.2O₂ compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Diffusion Of Hydrogen At Iron Apply For Electrochemical Oscillating Permeation, Li Zhang, Ren-He Yin, Zhan-Mei Sun

Journal of Electrochemistry

The diffusion of hydrogen in iron was measured using electrochemical oscillating permeation. Through the samples in the different frequencies, it was found that diffusion of hydrogen at iron is of linear relation with boundary condition, which is the key to Fick's diffusion equation amplitude in the liquor. We can exploit this line relation getting the diffusion of hydrogen at iron.

Research Progress On Electrode Material In All-Vanadium Redox Battery, Hua Li, Shou-Wen Chang, Chuan-Wei Yan

Journal of Electrochemistry

An all-vanadium redox flow storage battery possesses many advantages over conventional storage batteries.The development statue of two types electrode materials (metal and compound type) is introduced in this article.

Initial Stages Of Copper Electrodeposition On Glassy Carbon Electrode, Ling Huang, Rui Zhang, Min Gu, Fang-Zu Yang, Shu-Kai Xu, Shao-Min Zhou

Journal of Electrochemistry

Initial stages of copper electrodeposition on glassy carbon electrode from acid sulphate solutions were studied using cyclic voltammetry and chronoamperometry. The electrolyte solution was a 0.05 mol.L^-1 copper sulphate, 1.4～1.8 mol⋅L^-1 sulphuric acid containing 1 mg·L^-1 2-mercaptobenzoimidazole, Results show that 2-mercaptobenzoimidazole produced an inhibition of the copper deposition, probably related to the adsorption,sulphuric acid promote copper electrodeposition. The initial deposition kinetics corresponded to a model including instantaneous nucleation and diffusion controlled growth.Addition of 2-mercaptobenzoimidazole and sulphuric acid did not change the initial nucleation of copper electrocrystallization, it increased the nucleation rate and the number density of nuclei …

Xrd Study On Highly Preferred Orientation Cu Electrodeposit, Min Gu, Fang-Zu Yang, Ling Huang, Shi-Bing Yao, Shao-Min Zhou

Journal of Electrochemistry

Copper electrodeposit was obtained in CuSO₄+H₂SO₄ electrolyte solution by electrodeposition and its structure was studied by XRD. The results showed that copper electoddeposits with the highly preferred orientations of (220) and (111) could be obtained at current density 4.0 A/dm² and 15.0 A/dm², respectively. The texture coefficient (TC) values were increased by thickness of Cu deposits. The thickness would be, to obtain Cu electrodeposit with (111) highly preferred orientation, about 7 times of that of (220) highly preferred orientation, which indicated that(220) face was easier to be remained than (111) face and …

Ionic Conduction In Ba0.95Ce0.9Y0.1O3 - Α Solid Oxide And Its Performance In Fuel Cell, Gui-Lin Ma, Ding-Xian Jia, Li-Gan Qiu, Hui Shi, Rong Chen

Journal of Electrochemistry

Using Ba_0.95Ce_0.9Y_0.1O_3-α as a solid electrolyte and porous platinum as electrodes,hydrogen and oxygen concentration cells and hydrogen-air fuel cell were constructed, respectively. Electromotive forces (MEFs) of the gas concentration cells and I-V characteristics of the fuel cell were detdrmined in the temperature range of 600～1 000 ℃. The Ba_0.95Ce_0.9Y_0.1O_3-α exhibited almost the pure protonic conduction under hydrogen gas,and a mixed conduction of oxide-ion and electron hole with oxide-ion transport number of 0.3～0.5 under oxygen gas. It exhibited a mixed conduction of proton and oxide-ion with the …

Modification Of Molybdenum Nitride Electrode For Supercapacitor(I)——The Effect Of Ammonium Vanadate On The Properties Of Molybdenum Nitride Electrode, Xue-Liang Li, Dao-Rong Luo, Hua-Lin Wang, Jian-Bo He, Yun-Guei Zhu

Journal of Electrochemistry

The effect of vanadium on the properties of the electrode of molybdenum nitride has been studied by using XRD, SEM and cyclic voltammetry. Modified molybdenum nitride was made as follow: films were coated by dipping titanium sheet in the solution containing different composition of molybdenum oxide, ammonium vanadate, ammonia, glycol and oxalic acid, and coated films are reacted with free ammonia. The results show that the specific capacitance of modified electrode was considerably increased and the operation voltage was broadened with the addition of ammonium vanadate in the dipping solution. The mechanism of these effects generated is the formation of …

Some Consideration For Lithium-Ion Cells' Safety, Guang-Xia Hu, Jing-Ying Xie

Journal of Electrochemistry

The safety is the most important problem for lithium ion cells, especially for large lithium ion cells. In this paper, some information about lithium ion cells' safety can be learned by discussing several aspects of lithium ion cells, such as, materials of lithium ion cell, manufacturing processes, using conditions and so on.

Study On Hydrogen Evolution Performance Of Nickel-Tin Electrode, Tian-Yi Chang, Bao-Hong Zhang, Wenbo Cong, Yao Luo

Journal of Electrochemistry

The cathode active material with low hydrogen evolution overvoltage was prepared by electroplating Ni-Sn alloy on the ferrous basic body.This kind of material can be applied in the diaphragm type of electrolytic tank to decrease cell voltage and save energy. On the condition according with cathode solution in the electrolytic tank (NaOH 120 g/L, NaCl 190 g/L, 90 ℃, i=150 mA/cm²), the overvoltage of hydrogen evolution was 88 mV. By the X-ray diffraction analysis, it was found that the structure of this kind of material was different from that of Ni-Sn alloy applied in traditional decoration. By using …

Electrochemical Degradation Of Organic Wastewater By Three-Dimensional Electrode Reactor, Chun He, Tai-Cheng An, Ya Xiong, Dong Shu, Hui-Ling Hu, Xi-Hai Zhu

Journal of Electrochemistry

The electrochemical degradation of aniline was investigated using a novel electrochemical reactor, three-dimensional electrode reactor. The experimental results indicated that the reactor could efficiently remove aniline. The removal efficiency could be attributed to a combination of direct and indirect electrochemical reactions, that is, anodic oxidation and oxidation of electrogenerated H₂O₂ and hydroxyl radicals generated in electro-Fenton process. It was also observed that the removal efficiency was significantly dependent on applied voltage, Fe²⁺ concentration, pH value and electrolysis time. In the experimental range they all have a positive effect on the removal efficiency except for pH value. …

Pure Hap Film Prepared By Direct Electrodepositing On Metallic Surface And Its Mechanism, Hao-Bing Hu, Chang-Jian Lin, Fei Chen, Ren Hu, Ming Guo

Journal of Electrochemistry

In controlling concentration of Ca²⁺ and PO₄^3- in electrodeposition solution, the HAP film on Ti alloy has been deposited directly. Using XRD and SEM we have learned that prepared HAP is intact in crystal and equal in dimension. Thermodynamic calculation indicated that the HAP is easer formation of than that TCP of. With the XRD, SEM analyses and thermodynamic calculation, the electrodeposition mechanism has been discussed. It was proved that electrodepositon is a two-stage process and formation of HAP is a direct process from solution ions to HAP crystal without precursor.

Dielectric Properties Of A Ferroelectric Copolymer Langmuir–Blodgett Film, Mahantappa S. Jogad, Stephen Ducharme

Stephen Ducharme Publications

We report measurements of the real (epsilon prime) and imaginary (epsilon double-prime) parts of the relative complex permittivity of a Langmuir–Blodgett film of ferroelectric copolymer of vinylidene fluoride (70%) with trifluoroethylene (30%). The measurements were made in the temperature range of 35 to 125° C, and frequency range of 19 Hz to 5 MHz. The results indicate low frequency loss due to conduction and dielectric loss peak near the ferroelectric–paraelectric phase transition.

Electrically-Small Low Q Radiator Structure And Method Of Producing Em Waves Therewith, Craig A. Grimes, Dale M. Grimes, Faton Tefiku, Gang Lui

Chemical and Materials Engineering Faculty Patents

An electrically small radiator structure for radiating electromagnetic waves having an electrical size, k*a, with a value less than π/2 and above π/20,000 and configured to have at least a first and second magnetic, or electric, dipole element. Dipole elements are preferably oriented such that a source-associated standing energy value for the structure, or W_ds(t_R), is low, Radiative Q value preferably less than ⅓(k*a)³; and each of the elements, whether paired with respective electric dipole elements, is in electrical communication through a feed circuit to at least one power source. Further, a first …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

System Integration And Real-Time Control Architecture Of A Laser Aided Manufacturing Process, Mallikharjuna R. Boddu, Robert G. Landers, Srinivas Musti, Sanjeev Agarwal, Jianzhong Ruan, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper discusses a hybrid deposition–removal manufacturing system being developed at the University of Missouri--Rolla. The system consists of a laser system, five-axis CNC machining center, and powder feeder system. A description of the control software, real-time control architecture, and integration of various subsystems to build the hybrid system is given. The interaction of the real-time controller with various sensors and subsystems to monitor and regulate the process is presented. The communication between integrated process planning for the system and real–time control is also discussed in this paper.

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Role Of Si3n4 Amorphous Phase In Nc-Tin/A-Si3n4 Nanocomposites In Increases The Hardness And Thermal Stability, Keba Moto

Makara Journal of Technology

The role of Si3N4 amorphous phase in nc-TiN/a-Si3N4 nanocomposites will be shown and compared with polycrystalline ZrN/Ni which has no such amorphous phase (non-composites). The presence of amorphous phase Si3N4 increases the hardness of film as well as the toughness of the bulk nanocomposites under indentation load. It has been observed that nc-TiN/a-Si3N4 nanocomposites films has higher thermal stability than ZrN/Ni polycrystalline films.

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Correlation Between The Xps Peak Shapes Of Y1bu2cu3o7-X And Film Quality, Paul N. Barnes, Sharmila M. Mukhopadhyay, Timothy J. Haugan, Swaminathan Krishnaswami, Justin C. Tolliver, Iman Maartense

Mechanical and Materials Engineering Faculty Publications

X-ray photoelectron spectroscopy (XPS) depth profiling was used to investigate the compositional and chemical profile of a typical YBCO coated conductor architecture. Results of the process revealed that the Y(3d) photoelectronic peak shape in these films is very different from bulk YBCO. To investigate this, several samples of Y i Ba2Cu307_„ thin films were intentionally created of varying quality. The films were deposited on LaA10 3 by pulsed laser deposition with ./c. values ranging from poorly conducting up to several MA/cm2. Initial results indicated a potential correlation between the Y(3d) XPS peak shape (full-width-half-maximum) of the YBCO and the film …

Surface Switching Characteristics Of Variable Permittivity Dielectrics, Wayne Huebner, Eric J. Carleton

Materials Science and Engineering Faculty Research & Creative Works

Flashover voltage, lifetimes, and switch performance of insulators utilizing square thin and thick film electrodes were examined to determine the viability of using thin electrodes for reliable surface discharge switching. Gold, silver, and platinum were sputtered (0.25 µm) and screen printed (15 µm) onto Al₂O₃, TiO₂, and modified BaTiO₃ (MBT), then tested in air at 10⁵ Pa, under vacuum (10^-3/ torr), and while immersed in an insulating fluid, SF-2 (manufactured by 3M). For the measured range of 0.5 to 3 mm in air, the flashover voltage for all three insulators …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report For May-June-July 2002, John Farley

Transmutation Sciences Materials (TRP)

The goal of this project is to understand the basic science of corrosion in the steel/LBE system.

We are taking more data, typically using the newly installed X-ray Photoelectron Spectrometry (XPS) apparatus, and analyzing our existing data. Undergraduate students Denise Parsons and Julia Manzerova have helped a great deal in the analysis of the data. We can obtain the elemental composition as a function of position within the sample. This gives clues to the migration of materials, the composition of the protective oxide layer, and the basic science of the corrosion process. We found dramatic differences between the exposed and …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

44th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Final program, abstracts, and information about the 44th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-endorsed by the Colorado Section of the American Chemical Society and the Society for Applied Spectroscopy. Held in Denver, Colorado, July 28 - August 1, 2002.