Engineering Commons^™

Start The Presses, Stephen V. Ducharme, Alexei Gruverman

Stephen Ducharme Publications

A simple nanoimprinting method creates arrays of ferroelectric polymer structures suitable for low-cost, non-volatile memories. With the development of nanoimprinted high-quality ferroelectric nanomesa arrays, it seems that we now have all the necessary ingredients to print inexpensive, disposable organic memory chips.

Polymer Composite And Nanocomposite Dielectric Materials For Pulse Power Energy Storage, P. Barber, S. Balasubramanian, Y. Anguchamy, S. Gong, A. Wibowo, H. Gao, Harry J. Ploehn, Hans-Conrad Zur Loye

Faculty Publications

This review summarizes the current state of polymer composites used as dielectric materials for energy storage. The particular focus is on materials: polymers serving as the matrix, inorganic fillers used to increase the effective dielectric constant, and various recent investigations of functionalization of metal oxide fillers to improve compatibility with polymers. We review the recent literature focused on the dielectric characterization of composites, specifically the measurement of dielectric permittivity and breakdown field strength. Special attention is given to the analysis of the energy density of polymer composite materials and how the functionalization of the inorganic filler affects the energy density …

Metal Induced Crystallization Of Silicon Thin Films, Sandeep Kumar Raju Sangaraju

UNLV Theses, Dissertations, Professional Papers, and Capstones

Low temperature crystallization of thin film silicon is important for many industrial applications including flat panel displays and silicon thin film solar cells. Unfortunately this remains a major challenge since crystallization temperature of silicon is above 1,000 degrees Celsius, thus limiting to substrates that can tolerate high temperatures. The inability to deposit crystalline thin films on glass substrates is the reason why flat panel display industry uses amorphous silicon for LCD active matrix displays. Thus the ability to deposit crystallized thin film silicon at low temperatures will have significant impact on thin film silicon applications. It has been observed that …

Damage Characterization Of Beam-Column Joints Reinforced With Gfrp Under Reversed Cyclic Loading, Aly M. Said

Civil and Environmental Engineering and Construction Faculty Research

The use of fiber reinforced polymer (FRP) reinforcement in concrete structures has been on the rise due to its advantages over conventional steel reinforcement such as corrosion. Reinforcing steel corrosion has been the primary cause of deterioration of reinforced concrete (RC) structures, resulting in tremendous annual repair costs. One application of FRP reinforcement to be further explored is its use in RC frames. Nonetheless, due to FRP's inherently elastic behavior, FRP-reinforced (FRP-RC) members exhibit low ductility and energy dissipation as well as different damage mechanisms. Furthermore, current design standards for FRP-RC structures do not address seismic design in which the …

Mse News 2009, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• MSE Department Welcomes Engineering Fundamentals Chair
• MSE Department Welcomes New Professor
• Steel
• MSE Program Shines in US News Rankings
• MSE Alumnus Excelled in Mining Industry
• Student News
• Staff News
• Faculty News
• Alumni News

Model For Alumina Nanopore-Based Optical Filter, Nathan Lehman, Rama Venkat, Robert A. Schill

Electrical & Computer Engineering Faculty Research

Alumina nanopore structures find applications in magnetic sensors, optical filters, and various biological devices. In this work, we present a ray-optics model for the optical filter. We present a detailed simulation and a simplified analytical expression for the reflectance as a function of the alumina parameters such as pore diameter, pore density, alumina thickness, and a function of the wavelength and angle of incidence of the illuminating plane electromagnetic wave. The reflectance vs wavelength in the range of 400–800nm obtained from the simulation and the analytical expression are compared with that of the experiments for thin and thick alumina. All …

Electronic And Structural Properties Of Molybdenum Thin Films As Determined By Real Time Spectroscopic Ellipsometry, J. D. Walker, H. Khatri, V. Ranjan, Jian Li, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Walker, J.D., Khatri, H., Ranjan, V., Li, J., Collins, R.W., & Marsillac, S. (2009). Electronic and structural properties of molybdenum thin films as determined by real-time spectroscopic ellipsometry. Applied Physics Letters, 94(14). doi: 10.1063/1.3117222

Inclusion Modification In Steel Castings Using Automated Inclusion Analysis, Vintee Singh

Masters Theses

"The objective of this research is to study the effects of changing the melt and ladle practices (deoxidation, slag, refractory types, etc.) in steel foundries on the cleanliness and toughness of steel castings. This study used an automated inclusion analyzer ASPEX PICA-1020, which provides a rapid and accurate method for determining the composition, size, number, and spacing of the inclusions present in steel samples. The first step in this research was to complete a series of industrial tests to benchmark the current foundry ladle practices with respect to cleanliness of the cast steel. Trials were conducted at steel foundries using …

The Role Of Friction Stir Processing On The Microstructure And Mechanical Properties Of A Cast Aluminum Alloy, Saumyadeep Jana

Doctoral Dissertations

"Al-7Si-0.6Mg is one of the most important cast aluminum alloys because of its attractive mechanical properties and high castability. Microstructurally, the alloy consists of primary aluminum dendrites with eutectic Si particles in the interdendritic region. This makes the alloy quasi-brittle in nature which affects the ductility of the alloy to a great extent. In order to improve the ductility, the eutectic Si particles need to be refined which so far has been achieved by chemical and/or thermal modification. Friction stir processing (FSP) on the other hand can achieve the same through plastic deformation, and therefore replace the cast structure with …

Microstructural Evolution And Physical Behavior Of Palladium And Osmium-Ruthenium Noble Metal Films, Wen-Chung Li

University of Kentucky Doctoral Dissertations

Nanostructured noble metals exhibit novel physical, mechanical and chemical behavior, and hold promise for applications such as gas sensing and electron emission. A strong emphasis was placed on the processing and characterization of these materials, in the form of nanoporous or nanocrystalline thin films. Palladium-based and osmium-ruthenium alloys were investigated in this dissertation research and will be presented as follows:

(1) Preparation and Characterization of Nanoporous Metal Thin Films

(2) Characterization of Osmium-Ruthenium Coatings

Nanoporous palladium (np-Pd) thin films were prepared by dealloying co-sputtered palladium-nickel precursor alloys. Nanoporous structures were created with 3-D interconnected ligaments and open pores. Size of …

Material Flow And Microstructure Evolution In Friction Stir Welding Of Aa6111 Alloy Sheets, Manasij Kumar Yadava

Doctoral Dissertations

"Material flow and microstructure evolution are the two important aspects of the Friction stir welding (FSW) technique, which control the properties and performance of the friction stir welds. The present work investigates these two aspects of the FSW with main emphasis on the friction stir lap joints (FSLJs) on the AA6111 sheets. Due to the characteristic material flow during FSW, the faying surfaces in FSLPs are deposited in and around the weld nugget and create unavoidable defects. These defects reduce the load carrying thickness of the joints by providing an easy path for the weld failure. Therefore, to control the …

Freeze Casting Of Bioactive Glass And Ceramic Scaffolds For Bone Tissue Engineering, Qiang Fu

Doctoral Dissertations

"The main objectives of this dissertation were to explore the production of bioactive ceramic and glass scaffolds with oriented pore architectures by unidirectional freezing of suspensions, and to characterize the mechanical and biological performance of the scaffolds. Freezing of aqueous suspensions of hydroxyapatite (HA) or bioactive 13-93 glass particles resulted in the formation of scaffolds with a lamellar-type microstructure (pore width = 5-30 µm). The addition of polar organic solvents (such as 60 wt% dioxane) to the aqueous suspensions markedly changed the morphology and size of the oriented pores, giving scaffolds with a columnar-type microstructure and larger pre width (90-110 …

Microstructural Influence On Dynamic Properties Of Age Hardenable Femnal Alloys, Ryan A. Howell

Doctoral Dissertations

"A lightweight castable alloy was sought to reduce the MIL-PRF-32269 class II cast steel perforated armor's weight with the requirement that the material had to be manufactured utilizing existing foundry technology and without incurring large alloy cost increases to meet property requirements. Literature on wrought age hardenable Fe-Mn-Al-C alloys suggested this alloy system could achieve weight reduction through high aluminum concentrations with the highest reported strengths exceeding 2 GPa for a Fe-30Mn-9Al-0.9C composition. Even though ballistic testing had not been conducted on this system, high strain rate data of wrought alloys showed excellent work hardenability; greater than existing ballistic metals. …

Preliminary Investigation Of Metallurgical Structure And Mechanical Properties Of Cast Iron With High Aluminum Content, Pavel Bizyukov

Dissertations and Theses @ UNI

The problem addressed in this study analyzed various properties of cast iron with high aluminum content. This grade of cast iron was projected for use in the automotive industry. The benefits provided with high aluminum content are lower specific gravity and relatively inexpensive source materials with the potential of achieving high temperature properties.

The purpose of the study was to select suitable source materials and determine an effective melting technique, to investigate metallurgical structure and mechanical properties at given chemical composition, and, finally, to provide elaborate results.

The design of the experiment included the following steps: (a) selection and preparation …

Spectroscopic Characterizations Of Organic/Inorganic Nanocomposites, Jayesh Rasikalal Govani

Open Access Theses & Dissertations

Inorganic potassium dihydrogen phosphate (KDP) is widely known for its value as a nonlinear optical material. In this study, pure and l-arginine-doped KDP single crystals were grown by the slow solvent evaporation technique and further subjected to infrared absorption and Raman studies for the confirmation of chemical group functionalization and possible bonding between the organic and inorganic materials. The appearance in the infrared absorption spectra of additional vibrational lines, which mostly originate from disturbed N-H, C-H, and C-N bonds of the l-arginine-doped salt, confirm the interaction between KDP and the organic material. This affirmation is supported by more evidence from …

Computational Modeling Studies Of The Structures And Properties Of Organotin(Iv) And Stannyl-Thioether Systems With Comparisons To X-Ray Crystallography, Michelle R. Stem Joseph

Open Access Theses & Dissertations

Controlling the toxic effects of organotin(IV) compounds involves engineering the structure of the molecules to optimize their properties. Molecular engineering, coupled with improved capabilities to generate reliable computational optimization models (COMs), will enable researchers to have greater success at harnessing the highly specific cytotoxicity of organotins. For example, as the thio_n ligand phenyl groups were replaced with Cl atoms, the S-Sn intramolecularity was strengthened, the bond distance decreased, and the stannyl tetrahedral structure was deformed from its triphenyl conformation. With each substitution, conformation deformations lowered the damaging bioactivity levels of thio_n. Bonding various ligands to organotin(IV) compounds …

Experimental Study Of The Response Of Semiconductor Detectors For Edxrf Analysis., Sunil Kumar Valaparla

Open Access Theses & Dissertations

This present work relates to the study and characterization of the response function of an energy-dispersive x-ray spectrometer. The problems of energy, efficiency and resolution calibration of the system operating in the energy (5-60 keV) range are discussed. We present the operation characteristics of the portable pyro-electric x-ray generator (COOL-X) and the application of the calibrated response spectrum in the elemental analysis using X-ray Fluorescence (XRF).

We study the response of the Si(Li)-Pin XR-100CR semiconductor detector to low energy photons. The photopeak efficiency was determined experimentally by using radioisotopes and compared against a theoretical efficiency curve. The efficiency for gamma …

High Temperature Oxidation Behavior Of Nb-20mo-15si-5b-20cr Alloy, Julieta Angelica Ventura

Open Access Theses & Dissertations

Materials for high temperature applications, such as jet engines, gas turbines and turbine blades, require a balanced combination of physical and chemical properties to withstand the aggressive environments in which they are utilized. Some of the properties required are high strength, low density, high melting point and good oxidation resistance at elevated temperatures [1-3]. For this reason, the microstructure and oxidation behavior of the Nb-20Mo-15Si-5B-20Cr alloy (at.%) has been studied as a potential candidate to replace Nickel-based alloys currently used in the aerospace industry.

Short term oxidation (STO) and long term oxidation (LTO) studies have been performed in air for …

Observed Superspin-Glass Behavior In Ni0.5zn0.5fe2o4 Nanoparticles, Antony Adair

Open Access Theses & Dissertations

In this investigation we seek to identify the magnetic behavior of Ni0.5Zn0.5Fe2O4 nanoparticles though AC-susceptibility and DC-magnetization measurements. Powder x-ray diffraction was performed to determine the purity and average diameter ( ~ 9nm) of the particles. Aditionally, structure was confirmed by comparison through the International Centre for Diffraction Data's Powder Diffraction File [52] (PDF # 08-0234).

Zero-field cooled and field cooled DC magnetization measurements (bifurcation and blocking temperature), as well as M(H) hysteresis (below and above the blocking temperature) lead us to initially suggest that the material may in fact be superparamagnetic. However, further investigation of the real AC susceptibility …

Characterization And Cytotoxic Assessment Of Ballistic Aerosolized Particulates For Tungsten Alloy Penetrators Interacting With Steel Targets, Brenda Ivette Machado

Open Access Theses & Dissertations

The aerosolized particulates produced during an impact of depleted uranium munitions can potentially contaminate extensive areas around the impact sites and cause a wide spectrum of civilian and military damage. Thus materials such as WHA have been prompted for consideration. The present research is concerned with the regular collection of aerosol particulates associated with ballistic WHA rod penetration into rolled homogeneous steel (RHA) or other related steel armor as armor plate sequences. Particulate size characterization via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) along with chemical compositions via energy dispersive spectroscopy (EDS) were the focus of this research. …

Microstructural Characterization Of Overaged Gtd-111 Hp Turbine Buckets, Oscar Quintero

Open Access Theses & Dissertations

Superalloys are metallic materials that exhibit excellent mechanical strength and creep resistance at high temperatures. They have good surface stability and are corrosion resistant. Superalloys are mostly used in the aerospace industry, gas turbine engines and blades (hot zones of gas turbines), and where extreme heat is encountered. The focus of this research was on the GTD-111 Ni-base superalloy, which is a General Electric (GE) proprietary superalloy mostly used in gas turbine blades with the form of high pressure or first stage buckets. This alloys features better mechanical properties, creep resistance, and a higher stress rupture temperature than the commonly …

Additive Layer Manufacturing Of Ti-6al-4v By Electron Beam Melting From Powder Particles: Solid, Mesh And Foam Components Study, Sara M. Gaytan

Open Access Theses & Dissertations

Additive Manufacturing by Electron Beam Melting Rapid Manufacturing is a technology that consists of the fabrication of a CAD design by melting powder particles in a layer by layer fashion. In this study, Ti-6Al-4V has been utilized to fabricate solid, mesh and foam components by EBM technologies. Powder analysis of Ti-6Al-4V was performed to obtain a better understanding of the porosity obtained by the system. After proper optimization of the machine, and porosity control, microstructural analysis was performed to the components already mentioned and correlated by transmission electron microscopy. Besides the microstructural analysis, tensile and hardness testing was performed to …

Failure Analysis And Materials Characterization Of Hip Implants, Amanda Marie Bastidos

Open Access Theses & Dissertations

This research focused on the microstructural characterization and failure analysis of hip implant components. The main hip components analyzed were the femoral heads and the ultra-high molecular weight polyethylene (UHMWPE) liners. Previous research has shown that hip implants tend to fail by the PE liners due to adhesive and abrasive wear, delamination, and third body particles (metals, ceramics, and PE). The methods and procedures for analyzing the said failures consisted of non-destructive and destructive evaluations. Non-destructive evaluations included of techniques such as visual characterization and dye penetrant inspection (DPI)-which displayed macroscopic surface details and presented initial clues as to the …

Art In A New Light: Design And Assessment Of Illuminants To Reduce Photochemical Degradation Of Works Of Art, Monica Fabiola Delgado

Open Access Theses & Dissertations

The purpose of this research is to design the best lighting that will minimize long term photochemical degradation of Old Master Drawings and/or other works of art, while maintaining the patron's appreciation of the object's color and detail. The present approach is a technological refinement to the basic underlying earlier work on fluorescent lighting by W. A. Thornton, W.A. at General Electric1. Thin-film dielectric, multi-coating technology is used to create filters that eliminate ultraviolet light, near infrared light and significant unnecessary parts from the visible spectrum, thus maximizing the reduction in photochemical degradation, while maintaining optimal color rendering. Three interference …

Assessing Repeatability Of Four-Point Bending Method For Estimating Fatigue Cracking Of Hot Mix Asphalt, Sara -. Montazeri

Open Access Theses & Dissertations

The objective of this thesis was to assess the repeatability of four-point bending method for estimating fatigue cracking of hot mix asphalt. This experimental research examined the influence of mix proportions, specifically asphalt and air void contents, on fatigue behavior of asphalt beam specimens in the laboratory tested with four-point bending method of loading. Following the relevant specifications, the strain-controlled mode of loading was selected. Fatigue failure is expected to occur at the cycle which the flexural stiffness of asphalt specimen reduced to 50% of initial amount. Up to a 1,000,000 cycles of loading were applied to each specimen.

Different …

High Temperature Oxidation Characteristics Of Nb-10w-Xcr Alloys, Maria Del Pilar Moricca

Open Access Theses & Dissertations

The use of refractory metals in high temperature applications has been attractive for several years. Systems based on niobium represent a potential new generation of refractory materials systems because of their low density, high melting points, and strength at elevated temperatures. Despite these desirable characteristics, the widespread use of niobium-based alloys is limited because its oxidation resistance is still inadequate for structural applications. Understanding the oxidation kinetics of Nb-based alloys and the role of the different phases in the oxidation process is of crucial importance to improve the oxidation resistance of these materials.

The effect of Cr content on the …

Temperature-Induced Phenomena In Systems Of Magnetic Nanoparticles, Abdul Wazed Bhuiya

Open Access Theses & Dissertations

Magnetic nanoparticle ensembles have received a lot of attention, stemming in part from their current and potential applications in biomedicine and in the development of high-density magnetic storage media. Key to the functionality of these systems are microscopic structures and mechanisms that make them exhibit unique properties and behave differently from their bulk counterparts.

We studied microscopic structures and processes that dictate macroscopic properties, behavior and functionality of magnetic nanoparticle ensembles. As the temperature T strongly influences the magnetic behavior of these systems, we studied temperature dependent magnetic properties using AC-susceptibility and DC-magnetization measurements carried out over a broad range …

Microstructural Characterization And Heat Treatment Of A-286 Turbine Buckets, Christopher Michael Bradley

Open Access Theses & Dissertations

A-286 is an iron-based superalloy used extensively in land-based gas turbines for 2nd stage (low pressure) buckets and 1st and 2nd stage wheels. Although A-286 may appear to some as just another austenitic stainless steel, its elevated temperature properties are attributed to ' precipitate structures, effective distributions of alloy carbides in the forms of M23C6, M6C and MC, and solid solution strengthening. Unfortunately over the course of these components service lives microstructural degradation develops in the form of η-phase formation. The presence of η-phase, especially in large quantities, can have a negative effect on stress rupture properties. Resistance to creep …

Effects Of Build Orientation, Aging, And Pre-Conditioning On Mechanical Properties For Stereolithography-Manufactured Astm Type I Specimens Using A Design Of Experiments Approach, Karina Puebla

Open Access Theses & Dissertations

With industry's growing focus on the rapid manufacturing (RM) of end-use products, rapid prototyping (RP) or layered manufacturing (LM) machines that were originally designed to build prototypes may now be required to build functional end-use products. To successfully accomplish the transition, the available materials utilized in RP must provide the performance required for RM. The specific technology used must also be capable of producing repeatable and reproducible parts in regards to mechanical and dimensional properties.

A design of experiments approach was performed to determine the effects of build orientation, aging, and pre-conditioning on the mechanical properties. To perform the investigations, …

Exploring Poly(Ethylene Glycol) As A Suitable Material For Peripheral Nerve Regeneration Scaffolds Manufactured By Stereolithography, Nubia Zuverza

Open Access Theses & Dissertations

One of the challenges in tissue engineering is to have spatial and temporal control over the biological elements within a scaffold used to guide regeneration for example of transected nerves. Some of the physical and chemical characteristics to regulate include incorporation of bioactive domains and release of chemical signals. This study presents the use of stereolithography (SL) to incorporate localized domains for cell adhesion in addition to include releasable nerve growth factor (NGF) in the process of building poly(ethylene glycol)diacrylate (PEGda) hydrogel scaffolds. Besides providing sites for cell attachment, an ideal nerve guidance conduit (NGC) should be able to release …