Engineering Commons^™

Degradation Of Polystyrene Foam Under Radiant Heat Flux, James Butler

Graduate Theses and Dissertations

As the demand for liquefied natural gas has increased, safety concerns about the performance of transport vessels under fire conditions have been raised. Current codes for the sizing of the pressure relief systems require that the vessels are able to withstand an emmissive heat flux of 108kW/m2 and do not take into account the effects of insulation loss due to thermal decomposition of the insulation materials. To address this possible oversight in the current code models were presented to a working group organized by the Society of International Gas Tanker and Terminal Operators Ltd. focusing on the decomposition rate of …

Photodetectors And Photovoltaic Devices Based On Semiconductor Nanomaterials, Jiang Wu

Graduate Theses and Dissertations

Photodetectors based various nanostructures and plasmon enhanced solar cells are investigated in this dissertation. The motivation of the dissertation rise is driven by urgent need of both high efficiency photodetectors and solar cells.

First, quantum dot infrared photodetectors have been intensely investigated due to their promise in high performance photodetectors. However, the strain-driven growth of quantum dots has hindered the progress of quantum dot photodetectors. The presence of strain in the device presents complexity in designing as well as defects. Therefore, in this project, new designs of quantum dot photodetector structures are presented to improve the control over detection wavelength. …

Direct Contact Pyrolysis Of Hydrocarbons: A Source Of Hydrogen And Interesting Carbon Formations, Peter G. Faught

UNLV Theses, Dissertations, Professional Papers, and Capstones

The work detailed in this document looks at a novel liquid metal supported catalytic system for the generation of hydrogen by decomposition of ethanol through direct contact pyrolysis. The hydrogen is produced at relatively low temperatures (500-600°C) and has carbon and water as co-products. It should be noted that CO is not observed as a product at these low temperatures. This is to be contrasted with the hydrogen produced at higher temperature from ethanol which does contain carbon monoxide. The presence of carbon monoxide in hydrogen complicates fuel cell operation and catalytic chemical processes. Thus, the lack of CO in …

Modeling Of A Novel Solar Down Beam Test Facility Utilizing Newtonian Optics, Ryan J. Hoffmann

UNLV Theses, Dissertations, Professional Papers, and Capstones

As advances in concentrated solar energy progress there will inevitably be an increase in the demand of resources for testing new conceptions. Currently, there are limited facilities available for taking concentrated solar energy concepts from the laboratory bench scale to the engineering test scale. A proposed solution is a scientific and developmental facility that provides highly concentrated solar energy at ground level. The design presented is a solar down beam test facility utilizing a Newtonian optics approach with a flat rectangular down beam mirror to reflect and concentrate the sun's rays at ground level.

Literature review suggests a hyperbolic reflector …

Effects Of Grain Boundary Character On Dynamic Recrystallization Using A Modified Monte Carlo Method, Michael B. Morse

Boise State University Theses and Dissertations

Dynamic recrystallization (DRX) is the recrystallization that occurs during high temperature deformation of metals and alloys. While DRX has been observed experimentally, the parameters that affect the microstructure are still being explored. For example, the effects of temperature, strain rate, and initial grain size have already been studied, yet the effect of initial special boundary fraction is still unknown. Special boundaries are high-angle, low-energy grain boundaries. It is believed that higher initial fractions of special boundaries will lead to a delay in the onset of recrystallization and a higher peak stress.

Experimentation has shown that triple junctions are preferred nucleation …

Mechanical Properties Of Stir-Mixed Sicp-Reinforced Aluminium Composites, R Buntan, D Phuenchomphu, P Sukmoung, K Doomao, O Anunapiwat, T Patcharawit

Journal of Metals, Materials and Minerals

Aluminium composites have found their strength in engineering applications such as automotive, electrical and light-weight applications. To achieve uniform microstructure and good mechanical properties, the fabrication techniques are prime factors in controlling wettability and porosity problems. This research therefore aimed for studying microstructure-mechanical property relation of SiCp-reinforced 356 aluminium composites fabricated by a cost-effective stir casting process, to which three elemental additions, Al-5Ti-B, Sr, and Mg,were investigated. Furthermore, effects of SiCp additions (0-15 wt.%) and T6 heat treatment (530C/12h + 155C/4 h) on mechanical properties of the composites were also studied. The 356 aluminium ingot was melted at 700C then …

Spark Plasma Sintering Of Tungsten And Tungsten-Ceria: Microstructures And Kinetics, Jeffrey Bryce Perkins

Boise State University Theses and Dissertations

Tungsten casting is impractical, and tungsten compacts are most often produced by press-and-sinter or by hot pressing. The temperatures typically required to sinter tungsten above 90% dense are above 1800 ºC, and sintering times are typically hours. Alternatively, spark plasma sintering (SPS) can be used to consolidate materials to high densities at lower temperatures and shorter times than traditional sintering techniques. In this study, pure tungsten and tungsten with 1, 4, 10, 15, and 20 weight percent ceria were spark plasma sintered at varying pressures, temperatures, and times to investigate the microstructures and the kinetics of sintering.

Densification of tungsten …

Modeling And Control Of A Flexible Ionic Polymer Metal Composite(Ipmc) Actuator For Underwater Propulsion, Shivakanth Gutta

UNLV Theses, Dissertations, Professional Papers, and Capstones

The goal of this research is to model and control the underwater vehicle propelled by IPMC actuator. IPMC consists of an ionic membrane sandwiched between two metallic electrodes. When an external voltage is applied, IPMC undergoes large deformation due to transport of ions. Due to its ability to work in aqueous environments, it can be used for developing small scale underwater vehicles.

First, Finite element approach is used to describe the dynamics of the both single and segmented IPMC actuator. In the approach presented, each element is attached with a local coordinate system that undergoes rigid body motion along with …

Effect Of Vanadium On Subcritical Heat Treatment Behavior Of Hypoeutectic 16 Wt% Cr Cast Iron Containing 2 Wt% Mo, R Junsamoot, S Inthidech, K Sriprateep, P Sricharoenchai, Y Matsubara

Journal of Metals, Materials and Minerals

Subcritical heat treatment of austenite in alloyed cast iron by tempering at the temperature below pearlite transformation (A1), has been used to improve matrix hardness without hardening. Hypoeutectic high chromium cast irons containing 16 wt% Cr - 2 wt% Mo without and with V were prepared in order to clarify the effect of holding temperature and holding time on behavior of hardness and decomposition fraction of austenite in matrix (f) in subcritical heat treatment. As-cast specimens were held at temperature from 723 K to 923 K for 14.4 - 43.2 ks, and then cooled by fan air. In the as-cast …

Ni Electroless Plating Of Abs Polymer By Palladium And Tin-Free Process, P Dechasit, W Trakarnpruk

Journal of Metals, Materials and Minerals

A palladium and tin-free process for the Ni electroless plating of acrylonitrile-butadiene-styrene (ABS) polymer has been developed. The ABS was first etched then activated with Ni (or Co) ions. Ni or Co adsorbed was quantified by atomic absorption spectroscopy. Sodium borohydride solution was found to be effective in reduction of Ni (or Co) ions. By immersing in a Ni plating bath the Co (or Ni) can then auto-catalytically deposit a Ni film on the ABS. The amount and thickness of Ni film determined by SEM-EDX were the highest when using 3 g/L of nickel acetate solution, 0.5 M sodium borohydride …

Multi-Properties Of Chitosan/Montmorillonite Composite Films Incorporated With Virgin And Modified Montmorillonite, S Kittinaovarat, W Nitayaphat, N Jiratumnukul, S Charuchinda

Journal of Metals, Materials and Minerals

Chitosan (CTS) composite films were prepared by blending CTS with virgin or modified montmorillonite (vMMT or mMMT, respectively) and then spin coating. XRD analysis showed a good intercalation of CTS and the mMMT in the depolymerized 15 kDa CTS/mMMT composite. The tensile strength and rigidity of the CTS/vMMT and CTS/mMMT composite films increased, whilst the elongation at break decreased, with increasing levels of vMMT or, especially, mMMT from 0.1 to 2% (w/w). Both types of CTS/MMT composite films displayed a decreased oil and water absorption with increasing levels of incorporated vMMT or mMMT. Some aggregation of vMMT but not mMMT …

Recovery Of Zinc From The Spent Zinc-Carbon Dry Cell Batteries Through Pyrometallurgical Route, M Haque Khan, Asw Kurny

Journal of Metals, Materials and Minerals

Spent zinc-carbon batteries of all the five types (AAA, AA, C, D and 9V) were processed to recover zinc metal. All the components of the battery were separated, chemically analyzed and the anodic zinc parts were subjected to pyrometallurgical processing. Extraction of zinc was negligible when no fluxing agent was used. However, extent of recovery increased significantly when chloride salts: sodium chloride, calcium chloride and ammonium chloride were used as a fluxing agent. Among these, ammonium chloride gave the best result as flux. Using 10 %wt. of each flux, extraction of zinc was 90% for ammonium chloride, and around 75% …

Preparation Of Copper Lead Frame By Powder Metallurgy Technique, P Y. Chew, A H. You, T R. Vijayaram, B K. See, P S. Lim, M C. Ng

Journal of Metals, Materials and Minerals

Pure Cu is prepared with the dimension of 17.7 mm in diameter and 10 - 15 mm in height using powder metallurgical method to characterize its electrical and mechanical properties. These samples are compacted at a constant pressure of 280 MPa. Pure Cu pellets are sintered at 600C and 950C for 3, 4 and 7 hours. Before sintering, pure Cu pellet is subjected to SEM in order to check the compactness of the pellet, and also the grain structure of the Cu. All the pellets with different temperatures are re-weighed and sintered density are calculated after sintering. Besides that, porosity …

4-(N,N-Diethylamino)Benzaldehyde Thiosemicarbazone As Corrosion Inhibitor For 6061 Al - 15 Vol. Pct. Sic(P) Composite And Its Base Alloy, G M. Pinto, J Nayak, A N. Shetty

Journal of Metals, Materials and Minerals

The inhibitive action of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) on the corrosion behavior of 6061 Al -15 vol. pct. SiC(p) composite and its base alloy was studied at different temperatures in sulfuric acid medium containing varying concentrations of it, using Tafel extrapolation and AC impedance spectroscopy (EIS) techniques. Results showed that DEABT was an effective inhibitor, showing inhibition efficiency of 80 % in 0.5 M sulfuric acid. The adsorption of DEABT on both the composite and the base alloy was found to be through physisorption obeying Langmuirs adsorption isotherm.The thermodynamic parameters such as free energy of adsorption and activation parameters were calculated.

Novel Oxadiazole Containing Monomers For Polymeric Light Emitting Devices, Alexandra Foguth

All Theses

Organic light emitting diodes (OLED) have received a great deal of
attention in the research community in the past few decades. This
work focuses on OLEDs utilizing the donor-acceptor operational
approach. In specific a single layer device architecture with an
emissive layer of copolymerized hole and electron transport moieties
in an effort to frustrate phase segregation that can occur during
device operation. A new methacryalate based oxadiazole monomer,
4-[5-(biphenly-4-yl)- 1,3,4-oxadiazol-2-yl] phenyl methacrylate (mPBD) an electron transporter, was successfully synthesized. The new monomer was copolymerized with N-vinylcarbazole (VK), a hole transporter, to form statistical copolymers. The glass transition of the copolymers …

Influence Of Aging And Severe Plastic Deformation On The Shape Memory Behavior Of Ti-50.6at%Ni, William Shirley

All Theses

Martensitic phase transformations were investigated for Ti -50.6 at % Ni processed via severe plastic deformation (SPD) and subsequent aging for temperatures between 400 and 550C and times ranging from 1hr to 100hrs. Phase transformations of the SPD material were compared to material processed via solution treated at 800C and 850C for 1hr. Transformations were investigated with differential scanning calorimetry (DSC) and confirmed by X-ray diffraction (XRD) with optical microscopy being used to determine grain size. Solution treated samples displayed a single (1-1) B2↔B19' transformation prior to and upon initial aging, i.e. 400C/1h, 450C/1/10h. Intermediate aging conditions, 450C/100h; 500C/1/10/100h; and …

Effect Of Selected Phase Change Materials Concentration And Manufacturing Process On The Properties Of Plaster Mixture Systems, Rong Cui

All Theses

Phase change materials (PCM) are generally used in building construction materials for their ability to absorb and release large amounts of energy when their phase change happens at their specific melting temperature. This results in a significant increase in thermal mass of the building, a reduction in temperature fluctuations and therefore a reduction in heating and cooling loads. However, in order to properly select a PCM and optimize its integration in a specific building, the properties of building construction materials enhanced with PCM must be known. This research focuses on studying the effects of the concentration of a micro-encapsulated PCM …

Spectral Engineering Of Optical Fiber Through Active Nanoparticle Doping, Tiffany Lindstrom-James

All Dissertations

The spectral engineering of optical fiber is a method of intentional doping of the core region in order to absorb/emit specific wavelengths of light therby providing enhanced performance over current fibers. Efforts here focused on developing an understanding of optically active nanoparticles based on alkaline earth fluorides that could be easily and homogeneously incorporated into the core of a silica based optical fiber preform and result in efficient and tailorable spectral emissions.
Doped and undoped calcium, strontium and barium fluoride nanoparticles were successfully synthesized and characterized for their physical, chemical, and optical behavior. Distinct spectroscopic differences as a result of …

Highly Conductive Carbon Nanotube Fibers For Biomedical Applications, Vijoya Sa

All Dissertations

We developed a wet spinning process for the formation of polymeric fibers with high loading of single walled carbon nanotubes. The dissertation consists of five chapters. In the first chapter, the research goals were formulated and the art and technologies of fiber spinning from carbon nanotubes were critically analyzed. The next three chapters report the original results. Last chapter summarizes all the findings.
In the second chapter, we describe a surfactant based method of stabilization of carbon nanotube dispersions. The conditions of stability of nanotube dispersions in aqueous solutions of sodium dodecyl sulfate were analyzed. Using surface tension isotherms, the …

Process Parameter-Microstructure-Mechanical Property Relations Of Sicp-Reinforced Aluminum Composites Produced By Powder-Injection Casting, M Bunma, P Subarporn, R Bobuangern, T Patthannkitdamrong, T Thuanwong, T Patcharawit

Journal of Metals, Materials and Minerals

Aluminum composites are of interest for engineering applications such as electrical and especially automotive applications and their final physical and mechanical properties are usually determined by fabrication techniques. This research aimed to study effects of process parameters, which are i) argon gas flow rates at 5 and 10 l/min, and ii) casting temperatures at 620 and 680C, on integrity of the SiCp-reinforced 356 aluminum composites fabricated by powder-injection casting using a modified flux injection degassing machine. The SiCp additions are 0, 10 and 15 wt.%. Microstructure - mechanical property relations were constructed based on the predetermined process parameters. Aluminum 356 …

Synthesis Of Aligned Carbon Nanotubes By Floating Catalyst Method Using Ferrocene, R Ravindra, B R. Bhat

Journal of Metals, Materials and Minerals

The aligned carbon nanotubes (CNTs) have been synthesised by floating catalyst method using ferrocene as catalyst precursor and acetylene as carbon precursor. The reaction was carried out at 850C in double stage chemical vapor deposition (CVD) apparatus. The grown aligned CNTs were purified by air oxidation and acid treatment method. The aligned CNTs were characterised by using scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. The purity of CNTs was determined by Thermal analysis and X-ray diffraction method. The average diameter of aligned CNTs were around 20nm. This process not only produces aligned CNTs but also avoids the preparation …

Synthesis Of Zinc Oxide Nanorods And Use In Biosensor Applications, Anishkumar Manoharan

Graduate Theses and Dissertations

The main aim of this research was to develop a nanorod based biosensor for biomedical applications. In this project I use zinc oxide nanorods as the bio-material for biosensor. I fabricated these nanorods using a solution-based technique. Initially I coated a zinc oxide seed layer as the base. This seed layer was then annealed at 350 degrees for almost 1 hour. As a next step, interdigitated electrodes were fabricated on the top of the seed layer using a lift off process. The zinc oxide nanorods were then grown at 90 degrees for almost 4 hours along the electrodes. In this …

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Grain Boundary Behavior In An Ultrafine-Grained Aluminum Alloy, P. S. De, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

The low-angle grain boundary (LAGB) stability in an ultrafine-grained (UFG) Al alloy during monotonic loading was investigated by orientation imaging microscopy (OIM). the experiments show that boundaries with misorientation below ∼2.5 deg are stable, while boundaries with misorientation between 2.5 and 15 deg are unstable. Similar results were observed during cyclic loading of UFG Al alloy. This behavior was rationalized using the nonequilibrium thermodynamics concept. on the other hand, it is postulated that the grain boundary behavior in microcrystalline alloy is different because of the larger dislocation mean free path. © 2011 the Minerals, Metals & Materials Society and ASM …

Fluid Flow-Related Transport Phenomena In Steel Slab Continuous Casting Strands Under Electromagnetic Brake, Yufeng Wang, Lifeng Zhang

Materials Science and Engineering Faculty Research & Creative Works

In the current study, a three-dimensional (3D) numerical model is built to investigate the effect of a local-type electromagnetic brake (EMBr) on the fluid flow, heat transfer, and inclusion motion in slab continuous casting strands. the results indicate that the magnetic force affects the jet characteristics, including jet angle, turbulent kinetic energy, and its dissipation rate. to reduce the top surface velocity and stabilize the top surface, the magnetic flux intensity should be larger than a critical value. with a 0.39 T magnetic flux intensity, the top surface velocity and its fluctuation can be well controlled, and less slag is …

Influence Of Grain Size And Texture On Hall-Petch Relationship For A Magnesium Alloy, W. Yuan, S. K. Panigrahi, J. Q. Su, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

Friction stir processing was applied to a magnesium alloy to generate various grain sizes with the same intense basal texture. Subsequent tensile deformation along two orthogonal directions by easy activation or inhibition of basal slip follows the Hall-Petch relationship between yield stress and grain size in both directions. the Hall-Petch parameters are texture dependent. Easy activation of basal slip introduces lower values, while inhibition of basal slip leads to higher values. the Hall-Petch parameters are interpreted by texture and microstructural factors. © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Nondestructive Electrothermal Detection Of Corrosion, Brittany Ambeau, Harris Enniss, Stefan Schnake

Mathematical Sciences Technical Reports (MSTR)

Nondestructive testing and imaging plays an important role in many industries, e.g., the monitoring and maintenance of corrosion in aircraft. The general technique is to input energy in some form into an object, observe the object’s response, and from this input-output information determine the internal structure. New techniques are always being explored, and recently there has been much interest in methods that use multiple forms of energy. In this vein, we examine a new technique for imaging corrosion or material loss in an object by combining electrical and thermal measurements on some accessible portion of the object’s outer boundary. The …

Structure And Properties Of The Low-Density Phase Ι-Al2o3 From First Principles, Sitaram Aryal, Paul Rulis, Lizhi Ouyang, Wai-Yim Ching

Mathematical Sciences Faculty Research

Of the various phases of transition alumina, iota-alumina (ι-Al2O3) is the least well known. It is considered to be the end member of the mullite series in the limit of zero Si content. The structural details of ι-Al2O3 are not available and its physical properties are totally unknown. Based on an appropriately modified structure of a high alumina content mullite phase close to the 9-1 mullite, we have successfully constructed a structural model for ι-Al2O3. The simulated x-ray diffraction (XRD) pattern of this model agrees well with a measured XRD pattern obtained from samples that claim to belong to ι-Al2O3. …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …