Engineering Commons^™

Section Abstracts: Astronomy, Mathematics And Physics With Materials Science

Virginia Journal of Science

Abstracts of the Astronomy, Mathematics, and Physics with Material Science Section for the 90th Annual Meeting of the Virginia Academy of Science, May 23-25, 2012, Norfolk State University, Norfolk, Virginia

Corrosion Rate Of Carbon Steel For Flowline And Pipeline As Transmission Pipe In Natural Gas Production With Co2 Content, Andi Rustandi, Muhammad Adyutatama, Enriko Fadly, Norman Subekti

Makara Journal of Technology

The purpose of this research is to investigate the corrosion rate of carbon steel as flowline and pipeline in natural gas production with CO2 content. The influence of variety of conditions that represent the actual conditions in practice such as CO2 partial pressure and solution composition, particularly NaCl percentage were performed. Research conducted by polarization test and simulation methods using PREDICTTM software. The result of this research is used to illustrate the level of corrosion rate of typical carbon steel i.e. API 5L X-52 occurred in natural gas pipelines due to the effect of dissolved CO2. From the experiments obtained …

Concurrent Engineering Of Tolerance Synthesis And Process Selection For Products With Multiple Quality Characteristcs Considering Process Capability, Mohamad Imron Mustajib

Makara Journal of Technology

The existences of variances that are very difficult to be removed from manufacturing processes provide significance of tolerance to the product quality characteristics target of customer functional requirement. Furthermore, quality loss incurred due to deviation of quality characteristics of the target with a specified tolerance. This article discusses the development of concurrent engineering optimization model of tolerance design and manufacturing process selection on product with multiple quality characteristics by minimizing total costs in the system, namely total manufacturing cost and quality loss cost as functions of tolerance, also rework and scrap costs. The considered multiple quality characteristics have interrelated tolerance …

Modification Of Flow Structure Over A Van Model By Suction Flow Control To Reduce Aerodynamics Drag, Harinaldi Harinaldi, Budiarso Budiarso, Warjito Warjito, Engkos Achmad Kosasih, Rustan Tarakka, Sabar Pangihutan Simanungkalit, I Gusti Made Fredy Lay Teryanto

Makara Journal of Technology

Automobile aerodynamic studies are typically undertaken to improve safety and increase fuel efficiency as well as to find new innovation in automobile technology to deal with the problem of energy crisis and global warming. Some car companies have the objective to develop control solutions that enable to reduce the aerodynamic drag of vehicle and significant modification progress is still possible by reducing the mass, rolling friction or aerodynamic drag. Some flow control method provides the possibility to modify the flow separation to reduce the development of the swirling structures around the vehicle. In this study, a family van is modeled …

Optimizing Fermentation Medium To Produce Cyclosporin A Using Response Surface Methodology, Rofiq Sunaryanto

Makara Journal of Technology

Response surface methodology (RSM) is a three factorial model which illustrates the relationship between one or more independent variables. RSM can be used to optimize the fermentation medium for the production of Cyclosporin A from the isolate Tolypocladium inflatum. The optimal point of the response surface area is predicted by using a seconddegree polynomial model and applying the statistic model obtained from the central composite design (CCD). The results of optimizing the fermentation medium for Cyclopsorin using the three independent variables of glucose, casein, and KH2PO4 show that all three of the independent variables affect the production of Cyclosporin A. …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

Age, Gender, And Muscle Strength: A Study Based On Indonesian Samples, Henny Henny, Hardianto Iridiastadi, Iftikar Zahedi Sutalaksana

Makara Journal of Technology

Age and gender have been commonly used as a main criterion in accepting a job aplicant, but it is usually not clear how these affect job performance. While a number of recent studies have been done that describe the relationships between age, gender, and participants capacity (e.g., muscle strength), the results have been inconclusive. In Indonesia, in particular, such issues have been rarely investigated, and it is still important to study the issue since the relationships between these factors are population-specific. This study aimed at describing the relationships between age and muscle strength among workers for both genders. Ninety-six male …

Circularly Polarized Microstrip Array Antenna For Ground Segment In Quasi-Zenith Satellite System, Fitri Yuli Zulkifli, Eko Tjipto Rahardjo

Makara Journal of Technology

In satellite communication system, antenna plays an important role. Therefore, the antenna must meet some requirements, such as high gain, circular polarization, and good directivity. In this paper, a four element linear array triangular patch microstrip antenna with cross slot is designed to be used for Quasi-Zenith satellite system. A simulation study as well as experimental study was carried out. The simulation showed that the 3 dB axial ratio bandwidth of 87 MHz (2.569-2.656 GHz) is achieved while the measured results showed 96 MHz (2.556-2.652 GHz). The linear array of 4 element antenna has a gain of 13.73 dB and …

Tolerance Limit For Trucks With Excess Load In Transport Regulation In Indonesia, Sigit Pranowo Hadiwardoyo, Raden Jachrizal Sumabrata, Mohammed Ali Berawi

Makara Journal of Technology

Reliability of a road is mandatory since damaged will impede the traffic. Destruction is caused by various factors; one of the most important factors is excess load. Overload may give the load of each axle of a vehicle exceeds the determined standard. This condition occurs in trucks exceeding the load limit. In designing the structure of a road based on the method of Directorate General of Highways Ministry of Public Works of the Republic of Indonesia, axle load calculated in equivalent-number, or known as equivalent axle load (EAL), of 8.16 tons of standard axle. Total equivalent-number over the service life …

Earthquake Damage Intensity Relationship For Residential Houses In West Sumatra, Febrin Anas Ismail, Abdul Hakam, Fauzan Fauzan

Makara Journal of Technology

The Sumatra 30 September 2009 earthquake has damaged hundred thousand buildings in West Sumatra Province. The earthquake is located in 100 km offshore of Padang City, the Capital City of the province. Survey has been conducted to assess the damage of the building in few days after the earthquake. In this survey, the damage of buildings are categorised into 3 level that are heavily, moderate and slightly damages. This paper explores the level damage of building and then the intensity of the shaking in the affected area. Then based on the coordinate of every building location, the buildings are scattered …

Evaluation Of Universitas Indonesia’S Recharge Pond Performance And Potential Utilization For Raw Water Source, Nyoman Suwartha, Resky Agaslian Pramadin

Makara Journal of Technology

Evaluasi Kinerja Waduk Resapan UI dan Potensi Pemanfaatannya sebagai Sumber Air Baku. Waduk resapan Universitas Indonesia (UI) telah dibangun sejak 5 tahun yang lalu. Namun kegiatan monitoring dan evaluasinya sangat minim dilakukan. Tujuan dari studi ini adalah untuk mengetahui laju resapan, dan untuk mengevaluasi kondisi kuantitas dan kualitas air waduk resapan selama musim kemarau dan penghujan. Pengukuran kedalaman muka air, intensitas curah hujan dan penguapan dilakukan untuk menentukan ketersediaan air, laju resapan, dan imbangan air waduk. Sejumlah air permukaan diambil dari waduk resapan dan sungai di tiga titik sampling untuk mengetahui kondisi kualitas air eksisting. Hasil studi menunjukkan tidak ada …

Effect Of Methanol Induction And Incubation Time On Expression Of Human Erythropoietin In Methylotropic Yeast Pichia Pastoris, Adi Santoso, Neng Herawati, Yana Rubiana

Makara Journal of Technology

Erythropoietin (EPO) is a glycoprotein hormone consists of 165 amino acids and has molecular mass of 30,400 Daltons. The large quantities of these hormone required to satisfy clinical demand are currently met by recombinant expression in mammalian cell, namely chinese hamster ovary (CHO). Pichia pastoris has become popular yeast based protein production systems to substitute mammalian expression systems. P. pastoris is capable to use methanol as sole carbon and energy source. In this study, recombinant human EPO (rhEPO) protein obtained by expressing the hEPO gene in methylotropic yeast P. pastoris, strain X33. The present work was carried out to study …

Fuel Saving Strategy In Spark Ignition Engine Using Fuzzy Logic Engine Torque Control, Aris Triwiyatno, Sumardi Sumardi

Makara Journal of Technology

In the case of injection gasoline engine, or better known as spark ignition engines, an effort to improve engine performance as well as to reduce fuel consumption is a fairly complex problem. Generally, engine performance improvement efforts will lead to increase in fuel consumption. However, this problem can be solved by implementing engine torque control based on intelligent regulation such as the fuzzy logic inference system. In this study, fuzzy logic engine torque regulation is used to control the throttle position entered by the driver to achieve optimal engine torque. An engine torque vs. throttle position and engine speed mapping …

An Agri-Food Supply Chain Model To Enhance The Business Skills Of Small-Scale Farmers Using Corporate Social Responsibility, Wahyudi Sutopo, Muh. Hisjam, Yuniaristanto Yuniaristanto

Makara Journal of Technology

In general, small-scale vegetable farmers experience problems in improving the safety and quality of vegetables for supplying high-class consumers in modern retailers. Farmer Group and/or Cooperative (FGC) should be able to assist its members to meet the relevant provisions of modern retail on product specifications, delivery terms, and internal business requirements. This study proposed an agri-food supply chain (ASC) model that involves the corporate social responsibility (CSR) activities to enhance the business skills of the FGC as supplier of modern retailer. Multi-objective optimization programming is developed to determine the amount and timing of supply, level of farmers training skills, quality …

Pineapple Liquid Waste As Nata De Pina Raw Material, Agus Sutanto

Makara Journal of Technology

This research aims to study the quantity, quality, ecological and economic feasibility of nata de pina production (NP) from pineapple liquid waste (PLW). The design of the study employs complete random design (CRD) with three treatments: PLW without nutrients addition (A), PLW nutrients addition (B), and PLW stored for six months with nutrients addition (C). The nata de pina’s production factors measured were weight, thickness, fiber content, color, brightness, and residual waste. The highest weight was reached in treatment B (899 grams), followed by treatment A (616.4 grams), and C (477.8 grams). The thickness of NP of the height and …

Modeling Of A New Structure Of Precision Air Conditioning System Using Secondary Condenser For Rh Regulation, Aries Subiantoro, Nasruddin Nasruddin, Feri Yusivar, Muhammad Idrus Al-Hamid, Bagio Budiardjo

Makara Journal of Technology

A dynamic mathematical model for a new structure of precision air conditioning (PAC) has been developed. The proposed PAC uses an additional secondary condenser for relative humidity regulation compared to a basic refrigeration system. The work mechanism for this system and a vapour-compression cycle process of the system are illustrated using psychrometric chart and pressure-enthalpy diagram. A non-linear system model is derived based on the conservation of mass and energy balance principles and then linearized at steady state operating point for developing a 8th-order state space model suited for multivariable controller design. The quality of linearized model is analyzed in …

Microstructure Selection Of Sm–Co–Al Alloys To Increase Magnetization, Brian Dick

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

An ever increasing demand for higher performing magnets drives the need for new and innovative methods to achieve this goal. Sm-Co rare earth permanent magnets have a unique eutectic microstructure that, through refinement, could become a two-phase magnet which would significantly increase their energy product. The eutectic structure of Sm₈Co₉₂ is comprised of αCo rods embedded within a Sm₂Co₁₇ matrix. If the rods are small enough to encourage exchange coupling and the matrix is smaller than the single domain limit, then an efficient two-phase magnet is created.

Refining the Co rods and matrix size …

Laser Processing Of Metals And Polymers, Senthilraja Singaravelu

Physics Theses & Dissertations

A laser offers a unique set of opportunities for precise delivery of high quality coherent energy. This energy can be tailored to alter the properties of material allowing a very flexible adjustment of the interaction that can lead to melting, vaporization, or just surface modification. Nowadays laser systems can be found in nearly all branches of research and industry for numerous applications. Sufficient evidence exists in the literature to suggest that further advancements in the field of laser material processing will rely significantly on the development of new process schemes. As a result they can be applied in various applications …

Structural Health Monitoring Of M1114 High Mobility Multipurpose Wheeled Vehicle Armor System, Frank T. Sha

Theses and Dissertations

The M1114 High Mobility Multipurpose Wheeled Vehicle (HMMWV) has been the workhorse vehicle of the U.S. Armed Forces in Afghanistan and Iraq. Donald Rumsfeld, Secretary of Defense, was faced with massive public criticism in 2004 for not equipping our military personnel in Afghanistan and Iraq with M1114s that had the proper ballistic armor. In May 2004, a $618M Senate Bill was passed to increase the production level of HMMWVs and improve their ballistic protection capabilities while minimizing additional weight. While the military is taking advantage of using composite armor on the HMMWV, it does not have a rigorous method to …

Electromagnetic Interference Behavior Of Multiwall Carbon Nanotubes And Carbon Nanofibers Composites Under Fatigue, Peter A. Hunt

Theses and Dissertations

The United States military is researching the use of nanocomposite materials for structural applications on space vehicle systems. To reduce vehicle weight and mitigate the electromagnetic interference (EMI) brought on by the harsh space environment, today's space vehicles are made of composites coated with expensive conductive materials. Research on composites made of carbon nanotubes (CNT) and carbon nanofibers (CNF) has shown better EMI shielding performance with these materials compared to the current composites coated with expensive conductive materials. Thus, CNTs and CNFs offer the potential to replace the current composites. This study evaluated the effects of EMI behavior on one …

Creep Behavior In Interlaminar Shear Of A Cvi Sic/Sic Composite At Elevated Temperatures In Air And Steam, Matthew T. Pope

Theses and Dissertations

This research investigated the interlaminar shear performance of a SiC/SiC ceramic matrix composite. The interlaminar shear performance was observed in compression of double notched specimens (DNS) at 1200°C in both laboratory air and in steam. Compression to failure tests determined the as-processed interlaminar shear strength and interlaminar shear creep tests were conducted with stresses ranging from -22 MPa to -16 MPa. Primary and secondary creep regimes were observed in all creep tests. The specimens tested in creep at -16 MPa in air achieved run-out, defined as 100 hours at creep stress. The residual strength decreased slightly after 100 h of …

Metal Oxide Graphene Nanocomposites For Organic And Heavy Metal Remediation, Tanvir E. Alam

USF Tampa Graduate Theses and Dissertations

This thesis consists of two research problems in the water decontamination area. In the first work, the main focus is to understand the structure and photocatalytic activity of titanium dioxide with graphene (G-TiO2) which is synthesized by using sol-gel method. The photocatalytic activity of TiO2 is limited by the short electron hole pair recombination time. Graphene, with high specific surface area and unique electronic properties, can be used as a good support for TiO2 to enhance the photocatalytic activity. The obtained G-TiO2 photocatalysts has been characterized by X-Ray Diffraction (XRD), Raman Spectroscopy, Transmission Electron Microscopy (TEM), FTIR Spectroscopy and Ultraviolet …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

The Flow And Fracture Of Advanced Glasses - An Overview, Tanguy Rouxel, Richard K. Brow

Materials Science and Engineering Faculty Research & Creative Works

Editors' note on appropriate occasions, the International Journal of Applied Glass Science will engage the services of Guest Editors to help focus on topics of special interest to the international glass community. in this inaugural issue of this initiative, Professors Tanguy Rouxel and Richard Brow have accomplished just that in their overview of the subject "Flow and Fracture of Advanced Glasses." an introduction to this material and brief biographical sketch are given below. Our sincere thanks are extended to them for their help and cooperation throughout this undertaking, and especially the authors who contributed so much of their time, energy, …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

Preparation And Electrochemical Performance Of Lifepo4/C By Spray Drying Method Assisted With Organic Template, Quan-Bing Liu, Yang-Mei Jiang, Hui-Yu Song, Shi-Jun Liao

Journal of Electrochemistry

In this work, the LiFePO₄/C composites were prepared by the spray drying and carbothermal method, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge measurements. The effects of the organic assisted templates on the morphologies and electrochemical properties of the LiFePO₄/C composites were investigated. The results showed that the morphology and microstructure of the composites could be tuned by incorporating with the different templates. The morphology of the composite appeared to be solid microspheres if no organic template was added, while porous microspheres, nest-like …

Synthesis And Electrochemical Performance Of Xlifepo4·Yli3V2(Po4)3 Composites, Ping-Ping Ma, Zhi-Jian Liu, Jian-Hua Xia, Yu Chen, Pu Hu, Zhi-Chao Lu, Ding-Guo Xia

Journal of Electrochemistry

A series of xLiFePO₄·yLi₃V₂(PO₄)₃ composites were systematically synthesized through solid state reactions by variations in the proportions of LiFePO₄ and Li₃V₂(PO₄)₃. The properties of the prepared compounds were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The capacity of 162.7 mAh/g at 0.2 C rate was obtained with the relatively good cycle stability and good conductivity for 0.95LiFePO₄·0.05Li₃V₂(PO₄)₃ due to more uniformed distributed and smaller particle sizes.

Preparation And Characterization Of Mno/Tin Anode For Lithium Ion Batteries, Gao-Jie Xu, Hai-Yan Yang, Peng-Xian Han, Li-Xue Zhang, Ke-Jun Zhang, Chuan-Jian Zhang, Yu-Hua Fan, Cai-Feng Bi, Guang-Lei Cui

Journal of Electrochemistry

Manganese titanate (MnTiO₃) powder was prepared via a sol-gel method using manganese acetate and tetrabutyl titanate as raw materials, and citric acid as a chelating agent. Through high temperature nitridation of MnTiO₃ powder in ammonia, the MnO/TiN composite was obtained. The phase structure, composition and morphology of the composites were characterized by XRD, SEM and EDS. The electrochemical properties of the composite electrodes were studied by performing cyclic voltammetry, galvanostatic charge and discharge, and electrochemical impedance spectroscopy tests. The MnO/TiN electrode delivered specific capacities of 394 mAh·g^-1 and 146 mAh·g^-1 at the current density of …

Preparation And Hydrogen Evolution Properties Of Ni/Ag2O/Ruo2-Pt Cathodes, Shu Huang, Xue-Ming Li, Wu-Lin Li, Wen Wang

Journal of Electrochemistry

The Ni/Ag₂O/RuO₂-Pt composite cathode was prepared by sol-gel method using RuCl₃ and H₂PtCl₆ as raw materials. The effects of heat treatment conditions and AgNO₃ concentrations on hydrogen evolution properties were investigated. The morphology and composition of Ni/Ag₂O/RuO₂-Pt composite cathode have been characterized by XRD, XPS and SEM-EDS. It is demonstrated that the surface structure of Ni/Ag₂O/RuO₂-Pt composite cathode is more compact, with fewer cracks and larger surface roughness than pure nickel. At the conditions of 0.3 A·cm^-2, 90 ^oC, and …