Engineering Commons^™

Calculation Of Corrosion Rate Of Passive Metals With Charge Curve Analysis Technique, Yuan-Sheng Zhang, Min Gong

Journal of Electrochemistry

This work contains two parts: (1) A charge curve equation having no appro-ximation for passivated metal corrosion systems is derived and compared with the routine charge curve equation, which is virtual only when the polarization is minim(linear range). (2) It is simpler to analyze charge curve data by from of charge differential equation than from charge curve equation. After the charge curve data are measured, the slope of charge curve is computed by numerical differentiation method, then the charge differential equation may be transformed to a set of linear equations using polynomial approximation. The electrochemical parameters of corrosion system would …

Direct Electrolysis Of Seawater On Conducting Film For Microbial Anticorrosion 1. Simulation And Measurement Technique, Wei-Ling Hu, Ling-Ling Wu, Jing Zhou, Jing-Xin Li, Jin Luo, Zhong-Hua Lin

Journal of Electrochemistry

Based on the electrochemical micro probe and the weak signal detection technique, simulated test and measurement system were set up by the use of four-electrode cell(including a micro electrode), bipotentiostat, lock-in amplifier and three-dimensional micro manipulating device. Based on the system, the micrometer scale concentration distribution of trace hypochlorite, which is produced by direct electrolysis of seawater on the conducting film for preventing microbial corrosion has been obtained for the first time. Both relationships between concentration of hypochlorite and its reduction current, which is termed an working curve, and between the reduction current of hypochlorite and measured time are reported.

The Techniques Of The Paired Electrosynthesis, Hong-Kun Zhang, Deng-Ping Gu

Journal of Electrochemistry

In this Paper, we introduce our work on paired electrosynthesis. In conjunction with our research practice, we introduce electrolytic conditions,such as material of electrode ,courrent density and electrolytic temperature etc,as reference for researcher. We categorize the paired electrosynthesis techniques to widen our view on the paired electroorganic synthesis and to promote the deveopments of paired electrosynthesis techniques.

Influence Of Thiourea And Its Derivate On The Process Of Cathodic Electrodeposition Of Copper, Yun-Hui Dong, Ai-Hong Zou, Yun-Xia Zhao

Journal of Electrochemistry

The effects of thiourea and its derivate on the electrodeposition of copper from the dilute acid sulphate solutions have been studied by using potential sweep techniques at quasisteady state. Limiting current densities (I_d), exchange current densities (i₀) and α_n are obtained by data processing with the least square method. Thiourea has a depolarizing effect on the copper depositing at concentrations below 8 mg·L^-1, and a polarizing effect at higher concentration (>10 mg·L^-1), and it changes the mechanism of copper deposition reaction. Propenyltiourea and Phenylthiourea have a depolarizing effect on the …

A Study Of The Corrosion On Bronze, Hong-Fan Zhu, Hao Zhou

Journal of Electrochemistry

The bronze is the treasure in chinese metallic antique, which was typified by product in Shang-Zhou period (three thousands years ago). Because of corrosion, archaeological messages, such as inscription and pattern on the surface of bronze, would be damaged then the value of bronze antique decreased. The bronze disease is a common disease which forms powdery rust on the surface of bronze in atmospheric environment, the powdery rust emerge from under incrusted rust, then spreads, and eventually leads to bronze damaged. This paper investigates the bronze disease. According to the chemical and electrochemical tests in simulated occluded cell, the variation …

The Effects Of Metallic Cobalt Abbition On The Performance Of Pasted Nickel Electrodes, An-Bao Yuan, Jian-Qing Zhang, Wan-Chun Ding, Shao-An Cheng, Chu-Nan Cao

Journal of Electrochemistry

The Ni-foam pasted nickel electrodes prepared by coprecipitated Ni_1-XZn_X(OH)₂ with and without cobalt power addition have been studied. The electrode with addition of metallic cobalt showed a higher performance both in discharge capacity and cycle life. It is known from the experiment results that the addition of Co can remarkably increase the active material utilization which is suggested to be improvement of discharge depth due to the conducting CoOOH formed in the first activation charging. The superior capacity during cycling could be attributed to the synergistic action of zinc and cobalt addition ,especially to the …

Study On Synthesizing Of 2-Methylbutanoic Acid By Indirect Electrooxidation, Chong-Tao Zhao, Ze-Shan Zhu

Journal of Electrochemistry

The working conditions of synthesizing 2-methylbutanoic acid by oxidizing 2-methyl-1-butanol with tetrabutylammonium hydrosulfate (TBAS) or tetrabutylammonium perchlorate (TBAP) as phase transfer catalyst in sulfuric acid Cr(Ⅵ) oxidation medium was studied. The Cr(Ⅵ) oxidation medium could be electrolytic regenerated from Cr(Ⅲ), during above oxidation reaction. Under the optinum condition, the yield of 2-methylbutanoic acid is more than 95%.

The Ac-Impedance Analysis For Pluse Oxide Film Of Aluminium Alloy, Ai-Ling Du, Xi-Cheng Ma, He-Ming Zhang

Journal of Electrochemistry

Bode diagrams for aluminum PC (abbreviated from pulse current) oxide films were first obtained by AC-impedance measurements in a wide range of frequency. The experimental results show that different kinds of electrical equivalent circuits can be used for representing PC films and DC (abbreviated from direct current) oxide films separately, the main differences between them are their porous layers, the PC films are more even with little defects.Those are also verified by SEM and V-I characteristic curve measurements.

Electrochemical Synthesis Of Fes Electrode And Its Behavior Measurement, Cong-Sheng Guan

Journal of Electrochemistry

The Potential for the electrochemical synthesis of FeS electrode has been obtained by cyclic voltammetry. FeS electrodes were synthesiaed by controlling Fe electrode at -1.0 V in LiCl-KCl-Li₂S and Li(FClI)-Li₂S melts and their behavior were measured also. The FeS electrode synthesized in molten Li(FClI)-Li₂S has the best charge and discharge properties.

Foundation Sleeve For A Guardrail System, Dean L. Sicking, John D. Reid, John R. Rohde

Department of Mechanical and Materials Engineering: Faculty Publications

A highway guardrail terminal system having horizontally extending guardrail elements mounted on a plurality of posts. Foundation sleeves having an elongated slit along one side retain and support appropriate guardrail posts. A plurality of stiffing ribs extend across the slit at a distal portion of the tube. The sleeves enable a safer and faster removal of broken guardrail posts after vehicular impact.

Effect Of Temperature On Short-Term Creep Rupture Response In Polymer Matrix Pultruded Composites, Robert Harold Munson

Mechanical & Aerospace Engineering Theses & Dissertations

Polymer matrix pultruded composites have increasingly been used in applications where high strength-to-weight ratio and corrosion resistance are needed. Bridge and pier components are a couple of recent applications due the composite's resistance to corrosion from salt water. In applications of this sort, the material will commonly be subjected to sizable static loads while exposed to varying weather conditions. In using pultruded composites for these applications safely, a better understanding of the material's response to ambient conditions is necessary.

In this thesis, rectangular specimens of a polyester matrix glass reinforced pultruded composite sheet are subjected to both static tensile loading …

Newton Parameter Update Algorithm For Recurrent Neural Networks Applied To Adaptive System Identification And Control, Donald Allen Gates

Electrical & Computer Engineering Theses & Dissertations

This paper shows that the combination of a second-order neural network parameter update algorithm and internal network feedback can be effectively used for adaptive, nonlinear, dynamical system identification and control. Adaptive neural identification and control algorithms are typically utilized for real-time applications where the rate of adaptation is often critical. A fast, adaptive network parameter update algorithm is presented.

Simulation results show that this algorithm is capable of quickly identifying and adapting to changes in system parameters, making it feasible to use for real-time control and fault accommodation applications.

Adaptive Sampling For Coordinate Metrology, Robert Edgeworth, Robert G. Wilhelm

Department of Mechanical and Materials Engineering: Faculty Publications

An iterative sampling process for dimensional measurement is presented. The strategy is based upon the use of surface normal measurement data to develop an interpolating curve between sample points. The interpolant is used to select subsequent measurement targets iteratively. The process is repeated until the measurement converges to a complete and accurate evaluation of the surface. The required sample size is proportional to part quality. The most accurate parts will require the least sample points; whereas, lower quality parts will require a greater number of total samples. The method is particularly applicable to measurement of complex surfaces with coordinate measuring …

Large Amplitude Pitching Of Supermaneuver Delta Wings Including Flow Control, Yahia A. Abdelhamid

Mechanical & Aerospace Engineering Theses & Dissertations

The unsteady, three-dimensional Navier-Stokes equations are solved to simulate and study the aerodynamic response of a delta wing undergoing large amplitude pitching motion up to 90° angle of attack. The primary model under consideration consists of a 76° swept, sharp-edged delta wing of zero thickness, initially at zero angle of attack. The freestream Mach number and Reynolds number are 0.3 and 0.45 × 106, respectively. The governing equations are solved time-accurately using the implicit, upwind, Roe flux-difference splitting, finite-volume scheme. Both laminar and turbulent flow solutions are investigated. In the laminar flow solutions, validation of the computational results is carried …

Triangulation Rangefinder And Sight Positioning System, Jeffrey Hargrove, William G. Wickham, John E. Briggs

Mechanical Engineering Patents

A rangefinder includes an angle sensitive transducer and a programmed data processor to calculate the distance to a target. In one embodiment, the rangefinder also includes a point-to-point measuring device. Another embodiment provides a linear actuator to selectively move a sight indicator vertically. A yet additional embodiment includes a liquid crystal display which displays information to the user.

The Influence Of Heat On The Measurement Of Photocurrent At The Anodic Film Of Nickel Electrode, Hang Chen, Zhi-Yu Jiang

Journal of Electrochemistry

The influence of heat on the measurement of photocurrent for nickel electrode in 1 mol/L NaOH solution was investigated by using the photocurrent, photothermal and thermal current methods. It was found that the appearance of photocurrent in potential region of -0.75~0.20 V (vs. Hg/HgO electrode) was due to the p-type semiconductor properties of Ni(OH)₂ film in which is agree with the previous report. In the Ni(OH)₂/NiOOH redox potential region, the increase of temperature at the surface of working electrode during irradiation significantly promoted the electrochemical reaction strongly. The photocurrent observed in potential region 0.20~0.57 V is mainly …

Effects Of Nickel Content And Simulated Heat Affected Zone Of 2205 Duplex Stainless Steel On Pitting Corrosion, Horng-Yih Liou, Ju-Tung Lee, Wen-Ta Tsai, Rong-Iuan Hsieh, Yeongtsuen Pan

Journal of Electrochemistry

The effects of nickel content and Gleeble simulated heat affected zone (HAZ) of 2205 stainless steel on pitting corrosion were investigated in this paper. The results showed that nickel content, ranging from 4.5 wt% to 6.5 wt% in base metal, had only a minor effect on the electrochemical polarization curves, with all E_np's and E_pp's falling in the rang of 1100~1200 mV. Comparing with the base metal, the simulated HAZ microstructure caused an increase in the anodic current density, a distinct decrease in both E_np and E_pp , and a reduction in the passive …

The Influential Factors On The Triboelectrochemical Behaviors Of The Passive Alloys, Dong-Bai Sun, Tao Li, Hong-Ying Yu, De-Jun Yang

Journal of Electrochemistry

The tribocorrosion process of Fe-Cr alloys with different Cr content in H₂SO₄ solution was investigated. The influence of applied load, friction velocity, Cr content and concentration of H₂SO₄ in solution on the triboelectrochemical behaviors of the alloys was analyzed. It is shown that applied load and friction velocity have singnificant influence on the tribocurrent density in passive region when friction process occurs on part of the surface of alloy. Increasing the corrosion resistance of alloys or decreasing the aggressive of the solution can reduce the alloy removal velocity.

Investigation Of Solution Chemistry In Crevice Of Carbon Steel And Its Anodic Polarization Behavior, Zhuo Chen, Cui-Wei Du, Bei Cao, Yin-Shun Wu, Hai Yang, Zheng-Rong Zhang

Journal of Electrochemistry

A self-made wedge-shaped simulated crevice apparatus was designed to investigate the solution chemistry in crevice of carbon steel and its anodic polarization behavior. For carbon steel with 3.5%(wt) NaCl, the change and the distribution of electrode potential, concentration of Cl^- and pH value of solution in the crevice, and the current density of metal in the crevice were measured respectively under various conditions of anodic polarization. The results showed that without polarization the metal about 2 cm away from the opening of the crevice was attacked preferentially because of its lowest free corrosion potential. The anodic polarization promoted the …

A Study On The Cathode Protection Potential Against Pitting Corrosion, Chun-Chun Xu, You-Ping Liu, Xiao-Bo Zhang, Xu-Hui Zhao

Journal of Electrochemistry

The methods have been developed to determine the protection potential against pitting corrosion. They are based on the theory that the pitting protection potential (E_p) is actually the transition potential of the direction of current between the occluded cell and the external surface (E_T). E_T lasts from -220 mV to -440 mV (SCE), the lowest of which can be considered as cathode protection potential. The E_p values determined with cyclic potentiodynamic polarization method is included in the E_T with above methods.

The Adsorption Stability Of Interface Corrosion Inhibitor, Fu-Xing Gan, Di-Hua Wang, Jin-Yun Zou

Journal of Electrochemistry

Some new results on the adsorption stability of interface corrosion inhibitor are presented. The concept of adsorption stability and the factors influencing the adsorption stability were discussed. It is shown that the anodic desorption potential can be employed to evaluate the adsorption stability of the inhibitor as an empirical character in some conditions. Electrochemical oscillations phenomena were observed for the first time on a rotating iron electrode in H₂SO₄ solution containing organic inhibitor in the active potential region. These potentiostatic current oscillations can occur under cathodic polarization, as well as under anodic plarization. The oscillation period, amplitude, …

Electrochemical Behavior Of Riboflavin On Glassy Carbon Electrode, Hong Li, Lin-Cai Jiang, Liang-Nian Ji

Journal of Electrochemistry

The electrochemical behavior of riboflavin(RF) on glassy carbon has been investigated by using potential sweep, rotating ring-disc electrode and the measurement of differential capacitance. It is shown that a single well-behaved oxidation-reduction wave corresponding to a reversible two-electrons reaction apears in medium of pH<6, and the adsorption of RFH₂ formed by electro-reduction is weak and hence its solubility is good. In medium of pH>6, there are two separating but overlapping partly oxidation-reduction waves corresponding to two-step one-electron reaction. The adsorptions of RFH and RFH₂ produced by reduction reactions in medium of 6

Study On The Microband Array Electrode-Based Glucose Microsensor, Neng-Qin Jia, Chui-Jue Sun, Lin Gao, Zong-Rang Zhang, Jian-Zhong Zhu, Guo-Xiong Zhang

Journal of Electrochemistry

The microband array electrode (MAE) consisting of 11 Pt microband of 5 m in wide, 2000 m long and 85 m gap was fabricated with a thin film techology. The MAE was characterized by means of cyclic voltammetry in a solution of K₃Fe(CN)₆ and H₂O₂. The results showed higher current density on MAE than on conventional Pt eletrode due to the strong edge effect of the former. A glucose microsensor was constructed with the substrate electrode of microband array. Microband array electrode was modified by Nafion followed by the immobilization of ferrocene onto …

Oxidation And Adsorption Of Deoxyribonucleic Acid At Highly Ordered Pyrolytic Graphite And Glass Carbon Electrode, Jian-Zhang Zhou, Ling-Ling Wu, Jin Luo, Zhong-Hua Lin

Journal of Electrochemistry

It is shown that calf thymus DNA (CT DNA) can be adsorbed at highly ordered pyrolytic graphite (HOPG) electrode and detected by differential pulse voltammetry (DPV) and electrochemical atomic force microscopy (ECAFM). It is found that controlled potential pre-polarization influences largely the adsorption of dsDNA while it has little influence on ssDNA. It is demonstrated that ECAFM is useful to exploit adsorption of DNA at HOPGE. The pattern of adsorption of DNA at HOPG electrode that fits best with the experimental data is proposed. The results aslo shows that UV/Vis reflection spectroscopy, which has not been used in studying electrochemical …

Study On The Hydrogen Permeation Through Zinc Electrodeposit, Jiang-Li Cao, Ji-Xun Wu, Yan-Ping Lu, Jie Shi

Journal of Electrochemistry

The electrochemical hydrogen-permeation technique was used to study hydrogen permeation through zinc electrodeposit with bilayer specimens of Fe substrate/zinc electrodeposit. The effect of coating thickness on hydrogen diffusion coefficient and hydrogen steady-state flux was studied. The results showed that hydrogen diffusion coefficient was approximately in the range of 10-11 cm²·s^-1 rank and zinc coating could retard hydrogen permeation. Accordingly, hydrogen steady-state flux and effective diffusion coefficient declined while the coating thickness increased.

In Situ Ftir Spectroelectrochemical Study Of Palladium Hexacyanoferrate Thin Film Deposited On Glassy Carbon Electrode, Ai-Li Bo, Xiang-Qin Lin

Journal of Electrochemistry

The electrochemically deposited Palladium hexacyanoferrate thin film on Glassy Carbon electrode (PdHCF|GC) has been studied in HCl, KCl and NaCl solutions by in-situ external reflection FTIR spectroelectrochemical technique. It is found that the behavior of the electroactive PdHCF film can be understood in terms of two states: Pd₂Fe(II)(CN)₆ formed in the inner layer and (M⁺)2Fe(II)(CN)₆ (M⁺: electrolyte cation) formed in the outer layer. The inner layer is oxidized at E_m=0.87 V in 1 mol/L KCl, while for the outer layer Em=0.77 V(vs. Ag/AgCl). In 1 mol/L NaCl or HCl solutions, …

Influence Of Ptfe And Nafion On The Utilization Efficiency Of Pt/C Catalyst In Pemfc, Xiao-Liang Cheng, Bao-Lian Yi, Jing-Xin Zhang, Ming Han, Ya-Guang Qiao

Journal of Electrochemistry

With cycling voltammetry curve(C-V), TEM and SEM photographs, the influence of PTFE and Nafion on the platinum utilization in catalyst layer of PEMFC was investigated. The results show that in gas diffusion electrode, the blocking effect of PTFE in the platinum utilization is not pronunced. In the thin-film catalyst layer, the electron conduct of the catalyst was blocked by the nafion solid and this caused the decrease of platinum utilization. With the increase of the nafion content in the catalyst layer, both platinum utilization and the electron conductivity decreased in the catalyst layer. Because the molecule size of nafion is …

Preparation And Application Of Gold-Film On The Surface Of Bacterial-Modified Carbon Paste Electrode, Rong-Zong Hu, Yan-Ping Ruan, Hao Xu, Jin-Kun Fu, Wei-De Zhang, Wen-Yun Hu

Journal of Electrochemistry

A novel method for preparation of gold-film composed of ultra-fine gold particles was reported in this paper. The gold-film was prepared by electrochemical method on the surface of the paste electrode modified with the strain Bacillus sp. D01 which has strong ability to absorb and reduce Au³⁺. In addition, this paper reported an experimental method of determining trace amount of Cu²⁺ in water solution using cathodic stripping analysis to estimate the performances of the obtained gold-film. The experimental results indicated that this new method for preparation of gold-film is simple. The obtained gold-film electrode is stable and …

An Experimental Investigation Into The Effect Of Clearance And Torque On Load Sharing In A Bolted Joint, Jerry B. Robertson

Mechanical & Aerospace Engineering Theses & Dissertations

The shear load experienced by each bolt in a multi-fastener bolted butt joint is a percentage of the total load applied to the joint. Joint failure can be premature when one fastener is subjected to a disproportional amount of the total load. Conversely, the ultimate load the joint can endure may be increased if the distribution of loads can be equalized by some means. In this investigation, two and four fastener butt joints were studied. An instrumented bolt was constructed that could measure the bending stresses in the bolt associated with the bearing load. That data was converted into force …

Fatigue Response Of Repaired Thick Aluminum Panels With Bondline Flaws, David S. Conley

Theses and Dissertations

his research investigated the fatigue response of precracked 558 x 177.8 x 6.35 mm (22.0 x 7.0 x 0.25 in) 2024-T351 aluminum panels repaired with single-sided partially bonded, unidirectional, eighteen ply boron/epoxy reinforcements. Disbonds were introduced into the bondline of each repair during the adhesion process using teflon inserts. Five different disbond configurations, with varying disbond locations and sizes, were tested. Each repaired panel was subjected to constant amplitude cyclic fatigue loading with a maximum stress of 120MPa. Results from the different configurations were compared against one another and against repaired panels with no debonds to assess the effect of …