Engineering Commons^™

The Converging Frontiers: 3d Printing Of Polyvinyl Chloride (Pvc) For Environmental Remediation, Hazim F. Abbas, Salam Mohammed, Amamer M. Redwan

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

The global demand for effective environmental cleanup drives the need for innovative materials and techniques. 3D printing, which can produce complex and customized structures, offers promising solutions. PVC, a common, affordable, and durable polymer resistant to chemicals, is increasingly used for environmental applications. This report reviews recent advances in 3D-printed PVC for water purification, air filtration, and waste management. PVC’s strong properties, combined with the flexibility of 3D printing, enable the development of tailored, efficient components such as membranes, adsorbents, and catalytic supports. Technology also encourages a circular economy by recycling PVC waste into new feedstocks and on-demand, eco-friendly infrastructure. …

Smart Universities And Digital Transformation Based On Artificial Intelligence: A Case Of Al-Mustaqbal University, Ahmed Rasol Hasson

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Artificial Intelligence (A.I) is a key facilitator of universities procedures. Although the performance of AI has stretch out superior levels in developed countries, it is remain in its insufficiency in a lot of the developing nations. In this state, there is an imperative need to determine the important of adopting AI everywhere on Iraqi universities, due to the continuous utilize of a management old-fashioned systems. This research sight to explore applications that may influence the acceptance and adoption of AI in the Iraqi universities. This is achieved based on a qualitative approach of thematic analysis. The AI applications that were …

Experimental Study On Thermal Management Of Conventional Photovoltaic Module Using Hybrid Cooling System, Olufisayo Stephen Babalola, Olatunji Waliu Olademeji, Joseph Bukola Samson

Al-Mustaqbal Journal of Sustainability in Engineering Sciences

Photovoltaic (PV) cell junctions are thermally stressed, occasioned by heightened temperature beyond cell operating temperature threshold. This leads to efficiency diminution, which when properly addressed will change the fortune of PV electricity generation; which is more desired for reasons of clean energy and ubiquity of solar flux. Two 80W monocrystalline PV modules were installed at a tilt angle of 17°, south facing, on a stationary rack on top of Obafemi Awolowo University Physics Building. One module’s back surface had a hybrid cooling and the other as control. The PV modules cell temperatures, the ambient temperature, the solar irradiance and the …

Curing Duration Optimization To Reduce Shrinkage Cracking In One-Part Alkali-Activated Slag Concrete, A. Sadrmomtazi, H. Zanganeh

Journal of Sustainable Construction Materials and Technologies

The consequences of inadequate curing on one-part alkali-activated slag concrete (O-AAS) performance relative to ordinary Portland cement concrete (OPCC) have been investigated in this research. Prior to exposure to unsaturated conditions, samples underwent initial moist curing for durations ranging from 24 hours to one year. The testing program included compressive strength evaluation, chloride ion transport analysis, and measurement of free and restrained shrinkage. In addition, cylindrical cores were extracted from concrete columns to assess internal strength and chloride penetration resistance. Under unsaturated exposure, O-AAS exhibited a strength-aging phenomenon, with up to a 37% decrease in compressive strength over 360 days, …

Laboratory Investigation And Numerical Modelling Effect Of Carbon Nanotubes On Hot Mix Asphalt Permanent Displacement, Sepehr Saedi, Auwal Usman Nadada

Journal of Sustainable Construction Materials and Technologies

One of the primary causes of asphalt pavement deterioration is rutting; in contrast, one of the most effective methods to address this type of damage is the use of additives and quality evaluation during the design stages. In this research, laboratory testing and modeling using Abaqus software were employed to validate the laboratory results and predict and assess the potential for rutting. Carbon nanotubes (CNTs) were selected as an additive due to their exceptional mechanical properties and molecular interactions with bitumen. These nanotubes were used to modify the bitumen for the preparation of laboratory samples. The laboratory results from the …

Influence Of Early Microwave Curing On Performance Of Slag-Based Geopolymer Mortars, Ahmet Taşdemı̇R, Abdulkadir Çevı̇K

Journal of Sustainable Construction Materials and Technologies

In this article, an experimental study was conducted to examine the effect of curing time and microwave power on the compressive strength of early microwave-cured slag based geopolymers. Geopolymers have the potential to serve as an environmentally friendly substitute for cement-based building materials, and the use of microwave curing to geopolymers holds the promise of substantial strength improvement. Different microwave curing energies (300 - 800 Watts) were utilized at varying durations (10 - 60 minutes) on demoulded mortar specimens after one day. After that, compressive strength tests were conducted on both the cured and uncured specimens at three different ages: …

Two Members Of The Editorial Board Of Journal Electrochemistry, Kai Wu Elected As An Academician Of The Chinese Academy Of Engineering And Yi Cui A Foreign Academician Of The Chinese Academy Of Sciences, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Electrochemical Characterization And Modulation Of Biological Processes, Yue-Qi Li, Wei-Hua Huang, De-Chen Jiang, Bao-Hong Liu, Bin Su, Yang Tian, Jing-Juan Xu, Ping Yu, Feng Zhao, Huang-Xian Ju, Jing-Hong Li

Journal of Electrochemistry

Electrochemical processes lie at the core of biological function, governing energy transduction, metabolic flux, and molecular signaling. Recent advances in electrochemical science now allow these processes to be probed and controlled with unprecedented spatial, temporal, and chemical resolution. In this review, we present an integrated framework that progresses from fundamental mechanisms to analytical technologies and functional modulation. We begin by outlining electron transfer pathways in mitochondrial respiration, microbial extracellular electron transfer, and DNA- and protein-based charge conduction, followed by the principles of photon-electron conversion in photosynthesis and the central role of redox equilibrium in coordinating cellular responses. We then highlight …

A Novel Electrolyte Pyridine Additive For Enhancing Cycle Life Of Lithium-Ion Batteries, Peng-Cheng Wang, Ding-Chang Li, Jun-Tao Li, Guang-Bo Lu, Shi-Wen Wang

Journal of Electrochemistry

Lithium-ion (Li-ion) battery using a graphite (Gr.) anode and a lithium iron phosphate (LiFePO₄, LFP) cathode (Gr.||LFP) has been widespread in energy storage. To match the warranty period of energy storage systems, the lifespan of this kind of Li-ion battery, not only under room temperature but also under relatively high temperature, is critical. Exploration of functional electrolyte additive provides an efficient approach to address this issue. This study reports the usage of pyridine (Py) as a new electrolyte functional additive for Gr.||LFP. In the first cycle, it was found that Py can be reduced before ethylene carbonate and …

Journal Of Electrochemistry Officially Indexed By Leading Oa Databases Oarl And Coaj, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Feature Column Of Journal Of Electrochemistry Nominated For 2025 Top 10 Famous Columns Of Fujian Provincial Newspapers And Periodicals, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Use Of Alaçatı Stone Aggregate In Conventional And Self-Consolidating Concretes, Tahir Kemal Erdem

Journal of Sustainable Construction Materials and Technologies

Alaçatı stone or Alapietra stone is widely used mostly for building cladding. However, its production and use in the construction sites generate high amounts of waste (debris), causing environmental pollution in Çeşme which is a touristic district. This study investigated the reuse of Alaçatı stone as lightweight aggregate (LWA) in both conventional and self-consolidating concrete (SCC) mixtures. The concretes were prepared to have three different water-to-cement ratios (w/c), which were 0.38, 0.42 and 0.48. For each w/c, a conventional concrete mixture and two SCC mixtures with 60 or 70 cm slump flow were produced by varying the superplasticizer SP content. …

A Decision Support Model For Building Material And Component Reuse In The Context Of Circular Buildings, Havva Aksel

Journal of Sustainable Construction Materials and Technologies

Construction activities cause significant environmental impacts such as waste generation, pollution, resource consumption, and land use, which are expected to increase with global construction demands. To mitigate these environmental problems, the circular building occurs as an emerging concept depending on in the circular economy, which aims to minimize waste and redefine the “end-of-life” concept by reducing, reusing, recycling, and recovering materials. The reuse of building materials and components (BMCs) from existing structures represents a crucial strategy for achieving circularity in the built environment. Within this framework, design plays a key role. However, designing with reclaimed BMCs remains complex due to …

Expansion Limits Of Meshed Split-Thickness Skin Grafts, Haomin Yu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Split-thickness skin grafts are widely used to treat chronic wounds. Procedure design requires surgeons to predict how much a patch of the patient's own skin expands when it is meshed with rows of slits and stretched over a larger wound area. Accurate prediction of graft expansion remains a challenge, with current models overestimating the actual expansion, leading to suboptimal outcomes. Inspired by the principles of mechanical metamaterials, we developed a model that distinguishes between the kinematic rearrangement of structural elements and their stretching, providing a more accurate prediction of skin graft expansion. Our model was validated against extensive data …

Mae Enewsbrief July-Sept 2025, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Design And Development Of Biomimetic Hydrogel Interfaces For Enhanced Bioelectrical Signal Acquisition, Daniela Nikoloska

UNLV Theses, Dissertations, Professional Papers, and Capstones

Every second, human skin processes over one million sensory signals while maintaining properties such as electrical conductivity, mechanical adaptability, and regenerative capability that surpass all synthetic materials. Contemporary bioelectronic devices prove inadequate when contacting skin surfaces due to poor adhesion and electrical contact issues that prevent effective sensing. Despite advancements in wearable and bioelectronic technologies, current devices face major drawbacks when interfacing with human skin, particularly in maintaining firm adhesion, conformability, and low-noise electrical signal acquisition.

This research focuses on the development of a biomimetic hydrogel-based interface for bioelectronic sensing. Specifically, a hybrid hydrogel system composed of polydopamine (PDA)- doped …

Durability Of Alkali-Activated Concretes Under 5% Sulfuric Acid Environment, Celal Karabaş, Anıl Niş

Journal of Sustainable Construction Materials and Technologies

The investigation focused on the resistance to 5% sulfuric acid degradation of the alkali-activated concretes (AAC). The AAC was manufactured using a blended binder of 50% slag and 50% F-type fly ash. The AAC was activated using a blend of 14 M sodium hydroxide and sodium silicate, with a hydroxide-to-silicate ratio of 1/2,5. Six AAC were produced against a 5% sulfuric acid environment, varying the binder amounts (400–500–600 kg/m3) and activator-binder (A/B) ratios (0,45–0,55). The chemical resistance of AAC was evaluated by visual appearance, variation in weight and compressive strengths. The findings pointed out that more gypsum and higher weight …

Comprehensive Risk Assessment For Construction Site Managers In Kosovo: A Mixed-Method Approach, Muhamet Ahmeti, Besian Sinani

Journal of Sustainable Construction Materials and Technologies

This study developed and validated a hybrid ISO 31000:2018 Kosovo-compliant risk assessment framework tailored for construction site managers operating within transitional economies. The research employed audits of 20 ISO-certified contractors in Pristina, Kosovo, along with field observations, interviews, and quantitative risk matrices. The findings indicate a critical concentration of risk, with 70% of firms classified as "High" or “Very High” risk. The most prevalent hazards identified were working at height without collective protection, unprotected electrical systems, and manual handling of heavy materials. Regression analysis revealed that firms with a designated safety champion achieved significantly lower risk scores, whereas those with …

Behaviour Of Internally Strengthening Hollow Stainless-Steel Hot-Rolled Circular Columns Filled With Crumb Rubber And Recycled Aggregate Concrete, Wadhah M. Tawfeeq, Mohammed M. Rasheed, Mithaq Kohees, Ahmed W. Al Zandd, Saif Al-Balushi, Hamed Al Abdul Salam

Journal of Sustainable Construction Materials and Technologies

Stainless-steel sections are increasingly being utilised in favour of their higher durability. Simultaneously, the use of recycled materials in concrete is aligned with the global concern to encourage sustainable and environmentally friendly construction. The paper examined the behaviour of stainless-steel columns filled with concrete with crumb rubber (CR) and recycled aggregate (RA). It analysed the effect of different percentages of CR (0, 15, and 30) and RA (0, 15, and 50) on the compressive strength of the concrete and the performance of the columns using stainless-steel hollow sections. 20 specimens were manufactured, 18 of which were cast with concrete containing …

Piezoelectric Concrete: A Smart Material Approach For Energy-Harvesting Structural Technologies, Dianah Mazlan, Vynotdni Rathinasamy, Naveen Kumar, Liu Chunpeng, Elango Elango

Journal of Sustainable Construction Materials and Technologies

The rapid growth of urban infrastructure demands innovative materials that not only support structural performance but also contribute to sustainability through energy harvesting. Piezoelectric concrete, which integrates ceramics, polymers, nanomaterials, and bio-based fillers into cementitious matrices, has emerged as a promising solution. This review systematically explores the fundamentals of piezoelectricity in concrete, highlighting how stress-induced electromechanical coupling enables both energy harvesting and structural health monitoring. The paper critically evaluates major material systems including PZT ceramics, PVDF polymers, hybrid nanocomposites, and emerging bio-based materials, alongside their integration strategies such as embedded and surface-mounted approaches. Applications across pavements, bridges, and smart buildings …

In-Situ Investigations Of Calcium-Magnesium-Aluminosilicates (Cmas) Infiltration Effects On Thermal Barrier Coatings Under Extreme Environments Replicating Jet Engines, Zachary Stein

Doctoral Dissertations and Master's Theses

Calcium-magnesium-aluminosilicate (CMAS) particulates, such as sand or volcanic ash, are ingested by gas turbine jet engines during operation. When operating within high abundance regions, these particulates negatively interact and degrade the high temperature thermal barrier coatings (TBC) protecting underlying superalloy turbine blades vital to engine operation. These CMAS particulates melt within the engine and infiltrate into the ceramic coatings. In electron-beam physical vapor deposited (EB-PVD) TBCs, the CMAS within the intercolumnar gaps stiffens the coatings and causes thermomechanical induced high stress concentrations, risking crack formation. While molten, the CMAS thermochemically alters and destabilizes the coating, also risking coating failure. Premature, …

(R2122) Analysis Of Halo Orbits In The Elliptical R3bp With Mass Variation, Majhar Ali, Abdullah .

Applications and Applied Mathematics: An International Journal (AAM)

The elliptic restricted three-body problem investigates the motion behaviour of the variable mass infinitesimal body under the gravitational forces of the radiated oblate primary and dipole secondary. The equations of motion of the infinitesimal body are determined using Jeans law and Meshcherskii space time transformations. Using the Lindstedt-Poincaré method, we perform the solutions of the equations of motion. With the use of these solutions and the equations of motion, we numerically illustrate the time series, phase spaces, projections and the Halo orbits.

Powder Degradation Analysis In Reused Pure Tungsten For Electron Beam Melting (Ebm), Hernan Valenzuela

Open Access Theses & Dissertations

Additive manufacturing (AM) enables unparalleled design freedom and geometric complexity, driving its adoption in aerospace and medical fields. A major advantage of metal powder AM technologies, such as Electron Beam Melting (EBM), is its ability to reuse unused metal powder, reducing material waste and costs. However, reusing powder repeatedly alters its properties, affecting the final product. Despite its significance, research on powder degradation remains limited, primarily focusing on alloys like Ti-6Al-4V. This thesis investigates the degradation of pure tungsten powder reused over multiple Electron Beam Melting (EBM) cycles. A literature review revealed general powder-reuse mechanisms across additive manufacturing (AM) technologies …

Coupling Material Formulation Strategies To Tailor Piezoelectric Properties Of Ceramic Lattices, Amanda Lauren Borgaro

Open Access Theses & Dissertations

This thesis examines the material formulation and infiltration processes required to create interpenetrating ceramic composites with a particular focus on developing piezoelectric ceramic-epoxy lattice structures (PCELS). Following this, a high–solid loading barium titanite photopolymer resin (BT40) was developed to produce BTO scaffolds with controlled porosity suitable for metal infusion. The resin’s shear-thinning behavior and scattering-dominated curing response enabled the formation of stable, uniform ceramic structures whose pore networks directly influence infiltration behavior. Building on this foundation, a low-temperature Field’s Metal (FM) infiltration method was established using controlled thermal equilibration and the melting of pre-formed alloy rods. By maintaining the ceramic …

Development Of Oxide And Oxynitride Thin Films For Advanced Optical Applications, Nathan Christopher Episcopo

Open Access Theses & Dissertations

To develop Ga2O3 and TiOₓNᵧ thin films for optical applications, the process–structure–properties relationship was investigated using a comprehensive set of characterization techniques to establish the atomic structure and composition of the films in relation to the deposition conditions. The results provide critical insights into how deposition parameters influence the atomic structure and composition during magnetron sputtering. Furthermore, the correlation between atomic structure and composition with the optical and electrical properties of the films was examined to determine how variations in these factors affect functional performance. Collectively, these findings offer the necessary information to target desirable optical properties for Ga2O3 and …

Microstructure Evolution During Annealing Of Cryogenically Processed Cantor High Entropy Alloy, Mynel Gomez

Open Access Theses & Dissertations

This work focuses on the annealing behavior of a cryogenically processed Cantor high entropy alloy over a wide temperature range of 500–800°C. Scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction (XRD), and transmission electron microscopy (TEM) were employed to analyze the microstructural evolution, with particular emphasis on twinning. Hardness and grain size were measured to correlate these microstructural changes with mechanical properties. The cryogenically processed alloy exhibited a high density of twin bundles, resulting in an initial hardness of 338 HV. Upon annealing at 500 °C, 550 °C, and 600 °C, the material showed only a limited degree …

Decoupling Piezoelectric And Pyroelectric Effects In Anisotropic Polymer-Ceramic Lattices Produced Via Fused Filament Fabrication, Sofia Alexandra Perez

Open Access Theses & Dissertations

This thesis investigates how multi-material fused filament fabrication (FFF) can be used to engineer lattice structures that decouple piezoelectric and pyroelectric responses within a single polymer–ceramic composite. A hybrid ABS–BaTiO3/PLA lattice—referred to as the Hybrid PIZCAL—was designed to direct mechanical strain along the Z-axis while suppressing deformation in the transverse directions. After thermal poling, the lattice exhibited a 293% increase in Z-axis voltage sensitivity compared to a monolithic ABS–BaTiO3 cube and significantly reduced off-axis electromechanical output. Finite element simulations and directional compression testing confirmed that geometric anisotropy and material zoning produce strong, axis-selective piezoelectric behavior. The second part of this …

Simulation Of Stress, Deformation, And Vibration In Unlubricated Ball Bearings At Varying Rotational Speeds, Billy Dwiki, Moh. Hartono

Journal of Mechanical Engineering Science and Technology (JMEST)

Bearings are critical components in rotating machinery, and their performance is highly influenced by operational factors such as rotational speed, load, and lubrication. This study aims to analyze the deformation, stress, and dynamic behavior of SAE 52100 bearings under dry operating conditions at various rotational speeds, as well as to propose mitigation strategies for high-speed industrial applications. A finite element simulation was conducted using ANSYS R19.2 to evaluate the total deformation, equivalent elastic strain, Von Mises stress, and vibrational characteristics of a 6204-type SAE 52100 bearing. The simulations were performed across a speed range of 600 to 2000 RPM under …

Optimizing Zeolite Catalysts For Efficient Ldpe Plastic Waste Pyrolysis, Hilda Porawati, Mazwan Mazwan, Sukadi Sukadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The problem of plastic waste, particularly from low-density polyethylene (LDPE) plastic bags, poses a significant challenge in environmental management due to its non-biodegradable nature and widespread use in daily life. This study evaluates the influence of catalyst types on the characteristics and energy efficiency of liquid fuel products produced from LDPE waste pyrolysis. The three treatments compared were no catalysts, natural zeolite catalyst, and synthetic zeolite catalysts, each subjected to three different temperature variations: 250°C, 300°C, and 350°C. The observed parameters in this study were volume, product mass, cetane index, density, sulfur content, viscosity, flash point, calorific value, and energy …

Thermophysical, Rheological And Wear Resistance Of Canola Oil Biolubricant With Calcium Carbonate Additive Nanoparticle As Coolant In Cnc Machining, Alfandi Jaelani, Poppy Puspitasari, Diki Dwi Pramono, Alief Muhammad, Muhammad Kozin, Muhammad Kashif

Journal of Mechanical Engineering Science and Technology (JMEST)

Vegetable oil-based cutting fluids are of great importance in supporting green and sustainable manufacturing. This research introduces a new groundbreaking vegetable lubricant formulated with canola oil as the base material, coupled with CaCO3 nanoparticles synthesized from scallop shell waste and used as a cutting fluid in the AISI 1045 CNC machining process steel sprayed with minimum quantity lubrication (MQL). This investigation delves into the thermophysical, rheological, and wear resistance of the developed bio-lubricant. The results of this analysis show density value increased in the canola + CaCO3 0.15% sample by 3.28% of the pure canola sample, as did the viscosity …