Engineering Commons^™

Design Of Three Different Particle Size Distributions In Silver Paste Through Computer Simulation For Higher Electrical Conductivity, Kyungdeok Jang

Open Access Theses & Dissertations

In the field of printed electronics technology, researchers have tried to print highly conductive electrodes with fine width and height in order to manufacture high performance devices.

The purpose of this research is to print particle monolayer silver patterns which have better electrical conductivity than existing ones. The key idea of this experiment is to analyze silver inks with different sized particles. Let us consider a particle monolayer pattern printed with silver ink consisting of mono-sized particles. Inside of the pattern, there are some vacant spaces between the particles, which can lead to low electrical conductivity and discontinuity of the …

Digitally Manufactured Spatially Variant Photonic Crystals, Javier Jair Pazos

Open Access Theses & Dissertations

Metamaterials and photonic crystals are engineered composites that exhibit electromagnetic properties superior to those found in nature. They have been shown to produce novel and useful phenomena that allow extraordinary control over the electromagnetic field. One of these phenomena is self-collimation, an effect observed in photonic crystals in which a beam of light propagates without diffraction and is forced to flow in the direction of the crystal. Self-collimation however, like many of the mechanisms enabled through dispersion engineering, is effective in directions only along the principal axes of the lattice. To this effect, a general purpose synThesis procedure was developed …

Frequency Selective Surfaces For Extreme Applications, Jay Houston Barton

Open Access Theses & Dissertations

It is known that for high-power microwaves and other extreme environments, the use of resonant metallic elements in frequency selective surfaces can be problematic. The solution developed within this Dissertation to solve these problems was to use guided-mode resonance phenomenon to create all-dielectric frequency selective surfaces that could survive these extreme environments.

To fully understand how these devices work, three different computational electromagnetic methods are formulated and implemented. The formulation of these methods start with the differential form of Maxwellâ??s equation and are derived all the way down to the final simulation state. This is done sequentially and all the …

3d Printed Spatially Variant Anisotropic Metamaterials, Cesar Roman Garcia

Open Access Theses & Dissertations

The recent advancement in 3D printing has created a new way to design electronics and electromagnetic devices. This allows for a new breed of non-planar designs to be used, fully exploiting all three dimensions like never before. More functions can be fit into the same amount of space, products with novel form factors can be more easily manufactured, interconnects can be routed more smoothly, interfaces can be better implemented, electrical and mechanical functions can be comingled, and entirely new device paradigms will be invented. When departing from traditional planar topologies many new problems arise like signal integrity, crosstalk, noise, and …

A Robust Algorithm For Estimating The Balance Of Autonomic Nervous System With Application To Mental Fatigue Detection Using Photoplethysmographic (Ppg) Signals, Ajay Kumar Verma

Open Access Theses & Dissertations

Spectral- and time-domain analysis of Heart Rate Variability (HRV) signal is widely used as a quantitative marker of the Autonomic Nervous System (ANS) activity. A robust algorithm was developed to derive HRV from photoplethysmographic (PPG) signals, to compute FFT- and AR-based spectra of these HRV signals, and to determine time- and frequency-domain features. This algorithm has detrending, sample-rate reductions, false-peak removal, automatic peak detection, peak-to-peak (P-P) interval detection and correction, time-domain feature extraction, HRV signal generation, and spectral-domain feature extraction from the HRV signal. Adapting to the very low spectral contents of the input PPG signal is very helpful in …

Critical Analysis Of Transmitarray Antenna Design, Ahmed H. Abdelrahman

Electronic Theses and Dissertations

In recent years, transmitarray antenna concept attracts growing interests of many scientists in the antenna area. It combines the favorable features of the lens antenna that are based on optical theory and the microstrip arrays that are based on array theory, leading to a low profile design with high gain, high radiation efficiency, and flexible radiation performance. Transmitarrays are now emerging as a new generation of high-gain antennas for long-distance communications. In this dissertation, comprehensive analysis, new methodologies, and novel designs of transmitarray antennas are presented. * detailed analysis of the design of planar space fed array antennas is presented. …

Electron – Phonon Interaction In Multiple Channel Gan Based Hfets: Heat Management Optimization, Romualdo A. Ferreyra

Theses and Dissertations

New power applications for managing increasingly higher power levels require that more heat be removed from the power transistor channel. Conventional treatments for heat dissipation do not take into account the conversion of excess electron energy into longitudinal optical (LO) phonons, whose associated heat is stored in the channel unless such LO phonons decay into longitudinal acoustic (LA) phonons via a Ridley path. A two dimensional electron gas (2DEG) density of ~5×10¹²cm^-2 in the channel results in a strong plasmon–LO phonon coupling (resonance) and a minimum LO phonon lifetime is experimentally observed, implying fast heat removal from …

Model Analysis And Predictive Control Of Double Electrode Submerged Arc Welding Process For Fillet Joints With Root Opening, Yi Lu

Theses and Dissertations--Electrical and Computer Engineering

Submerged Arc Welding (SAW) for fillet joints is one of the major applications in the shipbuilding industry. Due to the requirement for the weld size, a sufficient amount of metal must be deposited. In conventional SAW process, the heat input is proportional to the amount of metal melted and is thus determined by the required weld size. To meet this requirement, an excessive amount of heat is applied causing large distortions on the welded structures whose follow-up straightening is highly costly. In order to reduce the needed heat input, Double-Electrode (DE) technology has been practiced creating the Double-Electrode SAW (DE-SAW) …

Machine-Human Cooperative Control Of Welding Process, Weijie Zhang

Theses and Dissertations--Electrical and Computer Engineering

An innovative auxiliary control system is developed to cooperate with an unskilled welder in a manual GTAW in order to obtain a consistent welding performance. In the proposed system, a novel mobile sensing system is developed to non-intrusively monitor a manual GTAW by measuring three-dimensional (3D) weld pool surface. Specifically, a miniature structured-light laser amounted on torch projects a dot matrix pattern on weld pool surface during the process; Reflected by the weld pool surface, the laser pattern is intercepted by and imaged on the helmet glass, and recorded by a compact camera on it. Deformed reflection pattern contains the …

Development Of Northrop-Grumman Mark Viie Training Unit And Wireless Video System For Use In Immersive Environments, Randall Lee Lewis

Theses and Dissertations--Electrical and Computer Engineering

A training unit has been developed that allows NVESD researchers to develop training simulations within virtual environments to enhance infantry skill and awareness. A ground station was developed to house a computer, power system, and video transmission system. This station will allow for a remote operator to wirelessly send a video/audio stream to the handset. The ground station also allows the use of external video and audio inputs to be sent using onboard converters. Different wireless frequencies were evaluated to determine the best for long-range transmission of content. A handset was developed from a carbon fiber prototype shell. The handset …

Multi-Domain, Multi-Objective-Optimization-Based Approach To The Design Of Controllers For Power Electronics, Jing Shang

Theses and Dissertations--Electrical and Computer Engineering

Power converter has played a very important role in modern electric power systems. The control of power converters is necessary to achieve high performance. In this study, a dc-dc buck converter is studied. The parameters of a notional proportional-integral controller are to be selected. Genetic algorithms (GAs), which have been widely used to solve multi-objective optimization problems, is used in order to locate appropriate controller design. The control metrics are specified as phase margin in frequency domain and voltage error in time-domain. GAs presented the optimal tradeoffs between these two objectives. Three candidate control designs are studied in simulation and …

Measurement And Modeling Of Humidity Sensors, Jingbo Tong

Theses and Dissertations--Electrical and Computer Engineering

Humidity measurement has been increasingly important in many industries and process control applications. This thesis research focus mainly on humidity sensor calibration and characterization. The humidity sensor instrumentation is briefly described. The testing infrastructure was designed for sensor data acquisition, in order to compensate the humidity sensor’s temperature coefficient, temperature chambers using Peltier elements are used to achieve easy-controllable stable temperatures. The sensor characterization falls into a multivariate interpolation problem. Neuron networks is tried for non-linear data fitting, but in the circumstance of limited training data, an innovative algorithm was developed to utilize shape preserving polynomials in multiple planes in …

Proposed Middleware Solution For Resource-Constrained Distributed Embedded Networks, Jason T. Rexroat

Theses and Dissertations--Electrical and Computer Engineering

The explosion in processing power of embedded systems has enabled distributed embedded networks to perform more complicated tasks. Middleware are sets of encapsulations of common and network/operating system-specific functionality into generic, reusable frameworks to manage such distributed networks. This thesis will survey and categorize popular middleware implementations into three adapted layers: host-infrastructure, distribution, and common services. This thesis will then apply a quantitative approach to grading and proposing a single middleware solution from all layers for two target platforms: CubeSats and autonomous unmanned aerial vehicles (UAVs). CubeSats are 10x10x10cm nanosatellites that are popular university-level space missions, and impose power and …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …

Humidity Sensor Circuit Using Real Time Operating System (Freertos) Kernel, Bojie Chen

Theses and Dissertations--Electrical and Computer Engineering

A humidity sensor can be used to measure the moisture content of the environment. The physical change of the sensor expresses as the change of electrical property like capacitance, resistance, voltage, current, frequency, etc. In order to process these analog signals digitally, microprocessor is involved in the measurement. This thesis presents design of a circuit to measure low moisture levels. The 16-bit RISC mixed signal microcontroller MSP430F249 from Texas Instruments will be used. The circuit has good performance at extremely low humidity levels.

Meanwhile, a small real time operating system kernel FreeRTOS, a market leading RTOS from Real Time Engineer …

A New Design Of Dc-Dc Converter For Capacitive Deionization Process, Zhiao Li

Theses and Dissertations--Electrical and Computer Engineering

The shortage of clean water has become a significant global problem, and capacitive deionization (CDI) is a technology that can be used to help relieve the problem. A Ćuk converter system that can recover energy from CDI cells is described. This converter transfers energy between two CDI cells when a cell is in its desorption period, allowing energy that would otherwise be lost to be recovered and improving overall system efficiency. In order to control the states of the MOSFET switches in the converter, a self boost charge pump is used. In this way, the microcontroller can control system duty …

Quantum Efficiency Enhancement For Gan Based Light-Emitting Diodes And Vertical Cavity Surface-Emitting Lasers, Fan Zhang

Theses and Dissertations

This thesis explores the improvement of quantum efficiencies for InGaN/GaN heterostructures and their applications in light-emitting diodes (LEDs) and vertical cavity surface-emitting lasers (VCSELs). Different growth approaches and structural designs were investigated to identify and address the major factors limiting the efficiency. (1) Hot electron overflow and asymmetrical electron/hole injection were found to be the dominant reasons for efficiency degradation in nitride LEDs at high injection; (2) delta p-doped InGaN quantum barriers were employed to improve hole concentration inside the active region and therefore improve hole injection without sacrificing the layer quality; (3) InGaN active regions based on InGaN multiple …

Harmonic Power Compensation Capacity Of Shunt Apf And Its Relationship To Design Parameters, Shafiuzzaman Khadem, Malabika Basu, Michael Conlon

Articles

VSI-based three-phase; power exchange mechanism; switching dynamics; three-phase systems; active losses; single-phase systems; power tetrahedron phasor diagram; shunt active power filter; harmonic power compensation capacity; four-wire systems; hysteresis band current control

The Marine Electronic Highway And Routeing Scheme Along The West Coast Of India And Sri Lanka : Feasibility Study : "Aiming Towards A Sustainable Maritime Transportation System", Sellakkannu I. Abul Kalam Azad

World Maritime University Dissertations

No abstract provided.

Analysis Of Power Efficiency Of A Direct-Driven Locally Fabricated Permanent Magnet Ac Generator For Small-Scale Wind Power Applications In Tanzania, Mussa Iddi Mgwatu Dr.

Tanzania Journal of Engineering and Technology (TJET)

The use of direct-driven permanent magnet alternating current (AC) generators offers the opportunity to reduced costs and increased system efficiency. This type of generator could be the best alternative for rural population whom are not connected to the national grid. To improve the design and efficiency of locally fabricated generators, it is imperative to characterize both their mechanical and electrical parameters. This paper presents the analysis of power efficiency of the synchronous permanent AC generator locally fabricated in Tanzania. In this case, load resistance and rotational speed are characterized using designed experiment. The output current and voltage of the generator …

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Physical Design Of A Smart Camera With Integrated Digital Pixel Sensors Using A 0.13Μm 8-Layer Metal Cmos Process, Mahir K. Gharzai

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The design of cameras has historically kept imagery and computational circuitry isolated in an attempt to maximize image quality by improving pixel pitch and routing density. Although this technique has worked in creating high density arrays of pixels for large resolution imagers, it has never been able to achieve high framerate computational operations.

A radical approach is introduced to solve this dilemma by creating compact, low- power pixel elements with built-in analog-to-digital converters that directly interface with digital logic. These pixels are capable of integrating alongside logic cells and to create an array of pixels inside the processor that can …

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Design Of A Low Power Cargo Security Device Using A Micropower Ultra-Wideband Impulse Radar, Brian M. Wihl

Master's Theses

Each year, thousands of cargo containers are broken into during shipping, costing billions of dollars in lost and damaged goods. In addition to removing its contents, intruders can also add unwanted and dangerous materials to a container, posing a threat to National Security. The possibilities of cargo container break-ins require that the containers go through check points at which they are physically searched. These searches often require the opening of the container, unloading and inspecting all cargo, and then loading the container and resealing it. This is a long and costly process.

Because of the high costs of break-ins and …