Engineering Commons^™

Impact Of Communication Latency On The Bus Voltage Of Centrally Controlled Dc Microgrid During Islanding, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Maintaining a sustainable and reliable source of energy to supply critical loads within a renewable energy based microgrid (MG) during blackouts is directly related to its bus voltage variations. For example, voltage variation might trigger protection devices and disconnect DERs within the MG. Centrally controlled MGs (CCMGs) type is dependent on communication. Therefore, it is very important to analyze the impact of communication networks performance degradation, such as latency, on the bus voltage of CCMGs. This paper investigates the effect of wireless communication technologies latency on the bus voltage and performance of centralized DC MGs. Two mathematical models were developed …

Using Gs/S Adc To Evaluate The Emi Of Gan-Based Power Devices, Chi Zhang

Electrical Engineering Theses and Dissertations

As the silicon-based power devices are gradually reaching their performance limits, new power transistors such as Silicon Carbide (SiC) and Gallium Nitride (GaN) FETs have been rapidly developed in recent years. GaN devices have been widely accepted by researchers for its higher speed and efficiency than silicon power devices. However, despite all its merits, the GaN device faces a more severe problem of electromagnetic interference (EMI) than the silicon device due to its high performance. Various control techniques of EMI have been studied so far and many of them require the evaluation of EMI. Research shows that the EMI level …

Investigating The Effect Of Detecting And Mitigating A Ring Oscillator-Based Hardware Trojan, Lakshmi Ramakrishnan

Electrical Engineering Theses and Dissertations

The outsourcing of the manufacturing process of integrated circuits to fabrications plants all over the world has exposed these chips to several security threats, especially at the hardware level. There have been instances of malicious circuitry, such as backdoors, being added to circuits without the knowledge of the chip designers or vendors. Such threats could be immensely powerful and dangerous against confidentiality, among other vulnerabilities.

Defense mechanisms against such attacks have been probed and defense techniques have been developed. But with the passage of time, attack techniques have improved immensely as well. From directly observing the inputs or outputs, adversaries …

Ku-Band Ag Channel Modeling, Albert Smith

Theses and Dissertations

With the rise in use of Unmanned Aerial Systems (UAS), there is a need for safe and reliable integration into existing infrastructure. A proposed system for beyond line of sight control links for UAS is a Ku-band air-to-satellite communication system. To ensure this proposed system does not interfere with existing terrestrial infrastructure that operates in the Ku band, an examination of the Ku-band air-to-ground channel is required. The focus of this thesis is the modeling of the Ku-band AG channel. Tests consisting of transmitting a single tone continuous wave signal were conducted with a signal generator onboard NASA’s Viking S-3 …

Wireless Sensor Networks For Smart Communications, Mu Zhou, Qilian Liang, Hongyi Wu, Weixiao Meng, Kunjie Xu

Electrical & Computer Engineering Faculty Publications

(First paragraph) In the first edition of the special issue titled “Wireless Sensor Networks for Smart Communications”, a total of 22 manuscripts were received and 6 of these were accepted. This issue demonstrated that network congestion, user mobility, and adjacent spectrum interference are the main reasons for the degradation ofcommunication quality inWireless Sensor Networks (WSNs).

Techniques Of Energy-Efficient Vlsi Chip Design For High-Performance Computing, Zhou Zhao

LSU Doctoral Dissertations

How to implement quality computing with the limited power budget is the key factor to move very large scale integration (VLSI) chip design forward. This work introduces various techniques of low power VLSI design used for state of art computing. From the viewpoint of power supply, conventional in-chip voltage regulators based on analog blocks bring the large overhead of both power and area to computational chips. Motivated by this, a digital based switchable pin method to dynamically regulate power at low circuit cost has been proposed to make computing to be executed with a stable voltage supply. For one of …

Non-Destructive Characterization Of Rotated Uniaxial Anisotropic Materials, Alexander G. Knisely

Theses and Dissertations

Electromagnetic material characterization of anisotropic media requires measurement diversity, minimal measurement uncertainty and insight into sample symmetry. Additionally, non-destructive characterization techniques are valued over legacy measurement techniques because a destructive approach requires sample preparation to execute a measurement. A Single Port Waveguide Probe (SPWP) non-destructive material characterization technique is proposed to accommodate measuring a metal backed, known thickness, rotated uniaxial anisotropic material. A rotated uniaxial sample possesses unique transverse constitutive components and a longitudinal constitutive component which is the same as one of the transverse values. The SPWP consists of a rectangular waveguide aperture cut in the center of a …

The Study Of Reconfigurable Antennas And Associated Circuitry, Kansheng Yang

Doctoral

This research focuses on the design of pattern reconfigurable antennas and the associated circuitry. The proposed pattern reconfigurable antenna designs benefit from advantages such as maximum pattern diversity and optimum switching circuits to realise 5G reconfigurable antennas. Whereas MIMO based solutions can provide increased channel capacity, they demand high computational capability and power consumption due to multiple channel processing. This prevents their use in many applications most notably in the Internet of Things where power consumption is of key importance. A switched-beam diversity allows an energy-efficient solution improving the link budget even for small low-cost battery operated IoT/sensor network applications. …

Comparison Of Grid Array And Microstrip Patch Array Antennas At 28 Ghz, Zeeshan Ahmed, Patrick Mcevoy, Max Ammann

Conference papers

A millimeter wave Grid Array Antenna for fifth generation (5G) communications is presented. The 20 cell, nearly-rhombic, 40×40 mm2 Grid Array Antenna structure is simulated and fabricated on a Rogers RT/Duroid 5880 substrate with thickness of 0.25 mm. The grid array has |S11|

Bio-Inspired Multi-Spectral Image Sensor And Augmented Reality Display For Near-Infrared Fluorescence Image-Guided Surgery, Nan Cui

McKelvey School of Engineering Graduate Student Theses & Dissertations

Background: Cancer remains a major public health problem worldwide and poses a huge economic burden. Near-infrared (NIR) fluorescence image-guided surgery (IGS) utilizes molecular markers and imaging instruments to identify and locate tumors during surgical resection. Unfortunately, current state-of-the-art NIR fluorescence imaging systems are bulky, costly, and lack both fluorescence sensitivity under surgical illumination and co-registration accuracy between multimodal images. Additionally, the monitor-based display units are disruptive to the surgical workflow and are suboptimal at indicating the 3-dimensional position of labeled tumors. These major obstacles have prevented the wide acceptance of NIR fluorescence imaging as the standard of care for cancer …

Multi-Gpu Acceleration Of Iterative X-Ray Ct Image Reconstruction, Ayan Mitra

McKelvey School of Engineering Graduate Student Theses & Dissertations

X-ray computed tomography is a widely used medical imaging modality for screening and diagnosing diseases and for image-guided radiation therapy treatment planning. Statistical iterative reconstruction (SIR) algorithms have the potential to significantly reduce image artifacts by minimizing a cost function that models the physics and statistics of the data acquisition process in X-ray CT. SIR algorithms have superior performance compared to traditional analytical reconstructions for a wide range of applications including nonstandard geometries arising from irregular sampling, limited angular range, missing data, and low-dose CT. The main hurdle for the widespread adoption of SIR algorithms in multislice X-ray CT reconstruction …

Forward Electrophysiological Modeling And Inverse Problem For Uterine Contractions During Pregnancy, Mengxue Zhang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Uterine contractile dysfunction during pregnancy is a significant healthcare challenge that imposes heavy medical and financial burdens on both human beings and society. In the U.S., about 12% of babies are born prematurely each year, which is a leading cause of neonatal mortality and increases the possibility of having subsequent health problems. Post-term birth, in which a baby is born after 42 weeks of gestation, can cause risks for both the newborn and the mother. Currently, there is a limited understanding of how the uterus transitions from quiescence to excitation, which hampers our ability to detect labor and treat major …

Robust Engineering Of Dynamic Structures In Complex Networks, Walter Botongo Bomela

McKelvey School of Engineering Graduate Student Theses & Dissertations

Populations of nearly identical dynamical systems are ubiquitous in natural and engineered systems, in which each unit plays a crucial role in determining the functioning of the ensemble. Robust and optimal control of such large collections of dynamical units remains a grand challenge, especially, when these units interact and form a complex network. Motivated by compelling practical problems in power systems, neural engineering and quantum control, where individual units often have to work in tandem to achieve a desired dynamic behavior, e.g., maintaining synchronization of generators in a power grid or conveying information in a neuronal network; in this dissertation, …

Statistical Performance Analysis Of Sparse Linear Arrays, Mianzhi Wang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Direction-of-arrival (DOA) estimation remains an important topic in array signal processing. With uniform linear arrays (ULAs), traditional subspace-based methods can resolve only up to M-1 sources using M sensors. On the other hand, by exploiting their so-called difference coarray model, sparse linear arrays, such as co-prime and nested arrays, can resolve up to O(M^2) sources using only O(M) sensors. Various new sparse linear array geometries were proposed and many direction-finding algorithms were developed based on sparse linear arrays. However, the statistical performance of such arrays has not been analytically conducted. In this dissertation, we (i) study the asymptotic performance of …

Self-Powered Time-Keeping And Time-Of-Occurrence Sensing, Liang Zhou

McKelvey School of Engineering Graduate Student Theses & Dissertations

Self-powered and passive Internet-of-Things (IoT) devices (e.g. RFID tags, financial assets, wireless sensors and surface-mount devices) have been widely deployed in our everyday and industrial applications. While diverse functionalities have been implemented in passive systems, the lack of a reference clock limits the design space of such devices used for applications such as time-stamping sensing, recording and dynamic authentication. Self-powered time-keeping in passive systems has been challenging because they do not have access to continuous power sources. While energy transducers can harvest power from ambient environment, the intermittent power cannot support continuous operation for reference clocks. The thesis of this …

Internet Traffic Forecasting Model Using Self Organizing Map And Support Vector Regression Method, Enrico Laoh, Fakhrul Agustriwan, Chyntia Megawati, Isti Surjandari

Makara Journal of Technology

Internet traffic forecasting is one of important aspect in order to fulfill the customer demand. So, the service quality of internet service provider (ISP) can be maintained at the good level. In this study self-organizing map (SOM) and support vector regression (SVR) algorithm are used as forecasting method. SOM is first used to decompose the whole historical data of traffic internet into clusters, while SVR is used to build a forecasting model in each cluster. This method is used to forecast ISPs traffic internet in Jakarta and surrounding areas. The result of this study shows that SOM-SVR method gives more …

Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy

Makara Journal of Technology

Theoretically, the preheating temperature refers to the start martensite temperature (Ms), and the martensite transformation can be considered as the conservation of the invariant habit-plane in the lattice structure. The habit-plane is the interface plane between austenite and martensite as measured on a macroscopic scale. From the calculation, Ms = 252 °C. The martensite formation can be affected by temperature or stress treatment. In this experiment, temperature treatment was conducted. The sample was treated at 250 °C ± 10 °C. Before and after the pre-heat treatment, the sample was characterized using the neutron diffraction method. BATAN’s Texture Diffractometer (DN2) with …

Investigation Of Ship Hull Girder Strength With Grounding Damage, Muhammad Zubair Muis Alie, Ristiyanto Adiputra

Makara Journal of Technology

The objective of the present study is to investigate ship hull girder strength as a result of grounding damage upon longitudinal bending. A bulk carrier and tanker are analyzed and Smith’s Method is adopted and implemented in the analysis program. An efficient solution procedure is performed by assuming the cross-section remains plane and the vertical bending moment is applied to the cross section. As a fundamental case, the damage is simply created by removing the elements from the cross section. Welding residual stress, initial imperfections, and crack extensions are not considered. The grounding damage is made by two conditions, namely …

Experimental Evaluation Of A Krypton Propellant Arrangement In A T-100-3 Hall-Effect Thruster, Adam Patel, Javier Cortina Fernandez, Justin Chow, Osvaldo Alejandro Martin, Alexey Shashurin

The Summer Undergraduate Research Fellowship (SURF) Symposium

Stationary Hall thrusters are electric, moderate-specific impulse propulsion systems developed in Russia. These devices manipulate electric and magnetic fields to expel ionized gas (plasma) components, resulting in thrust. The success of Hall-effect engines in USSR satellite-transfer missions quickly sparked western interest in the design. Extensive government and academic study commenced shortly after the dissolution of the Soviet Union, when the technology was made available to the United States. The common SPT-100 model was the primary subject of such studies. Unfortunately, limited literature exists for rare and uncommon Hall thruster models. The T-100-3 stationary plasma thruster suffers from this gap; few …

Spice Based Compact Model For Electrical Switching Of Antiferromagnet, Xe Jin Chan, Jan Kaiser, Pramey Upadhyaya

The Summer Undergraduate Research Fellowship (SURF) Symposium

A simulation framework that can model the behavior of antiferromagnets (AFMs) is essential to building novel high-speed devices. The electrical switching of AFMs allows for high performance memory applications. With new phenomena in spintronics being discovered, there is a need for flexible and expandable models. With that in mind, we developed a model for AFMs which can be used to simulate AFM switching behavior in SPICE. This approach can be modified for adding modules, keeping pace with new developments. The proposed AFM switching model is based on the Landau-Lifshitz-Gilbert equation (LLG). LLG along with an exchange coupling module is implemented …

Study Of The Effective Thermal Conductivity Of Polymer Composites With Varying Filler Arrangements, Debraliz Isaac Aragones, Rajath Kantharaj, Aaditya Candadai, Amy Marconnet

The Summer Undergraduate Research Fellowship (SURF) Symposium

Alternative thermal management solutions for electronic devices are being widely explored due to the increasing heat concentration that results from shrinking sizes and increasing power of modern electronics. Clearly, there is a need to spread the heat effectively in these systems, and polymer composites can potentially provide high thermal conductivity at low filler fraction while maintaining desirable mechanical properties for electronic packaging. The present study aims to investigate the effective thermal conductivity of various copper filler arrangements in a polymer matrix. The polymer composites are fabricated using laser cut acrylic templates to embed aligned copper rods in epoxy and create …

Satellite-Based Monitoring Of Spatiotemporal Changes In Batudulang Forest In Sumbawa, Indonesia, Mohammad Muslim, Arief Budhi Witarto, Wahyu Indrajaya

Makara Journal of Technology

Space-based earth observation technology applicable to forest inventory and monitoring is well known in the scientific community. High-resolution satellite images form an important data source for forest mapping and change detection at regional and national scales. The value of forest change information derived from remote sensing data is significantly enhanced if this information is integrated into a spatially explicit geographic information system. Satellite-based rapid assessment was conducted to measure spatiotemporal changes in Batudulang forest over the years. The general approach to quantify change in the spatial aspect of the forest involved change detection using moderate-resolution imaging spectro-radiometer satellite-based normalized difference …

Strength Structure Analysis Of Main Gate Graving Dock Using Pontoons For Condition Repairs, Budianto Budianto

Makara Journal of Technology

Main gate graving dock with pontoon type can certainly suffered some level of damage after a long period of operation. Many employments within the graving dock can delay the process repair of main gate. The main gate may not be opened, because employees are still working to ship fabrication process under sea waterline. For accommodate these interrelated conditions, the best solution with repair one side of the main gate with type pontoon and employees can still work ship fabrication process in graving dock conducted simultaneously. The repair process conditions must be required main gate structure that consists of only one …

Microstructures And Hardness Of Tig Welded Experimental 57fe15cr25ni Steel, Parikin Parikin, Mohammad Dani, Abu Khalid Rivai, Agus Hadi Ismoyo, Riza Iskandar, Arbi Dimyati

Makara Journal of Technology

The microstructures and hardness of tungsten inert gas (TIG) welded experimental 57Fe15Cr25Ni steel were investigated through optical–scanning electron microscopy analyses and with a hardness tester, respectively. The welding process restructured the constituent atoms into regular and irregular crystal lattices. Rapid cooling of the weld metal allowed the formation of a dendritic (columnar) structure, with porous grains. By contrast, slow cooling influenced HAZ and led to the formation of grain structures. The crystal lattice became more organized and larger than other zones. Meanwhile, the base metal formed circular nets that covered large area inside thick and thin grain boundaries. The diffraction …

Mapping Of Bruise Of Oil Palm Fresh Fruit Bunch During Loading And Transportation From Field To Mill, Andreas Wahyu Krisdiarto

Makara Journal of Technology

Fresh fruit bunches (FFBs) are used as raw materials for palm oil, and their transport from a field is a critical step to maintain their quality. Fruit integrity should be maintained so the mill can efficiently obtain palm oil with less than 5% free fatty acid content. Physical treatments for FFBs during loading to truck bins and transport may cause physical injuries. This research aimed to map fruit bruises. The map can be used as a basis in managing transport of FFBs. Physical injuries were assessed by bruise index (BI), which was calculated by measuring the bruise area and weight …

Benchmarking Product Service System Of Generator Set Distributors, Venny Violetta Tiurindah, Tanika Dewi Sofianti

Makara Journal of Technology

Power generation is an industry that is essential to sustain daily life and competes with generator set distributors. The product service system of distributors must be improved to survive the competition. This research aims to develop tools for benchmarking the product service system of generator set distributors. Benchmarking identifies gaps between a product and other competitors’ products. In this work, a product service system board is used to visualize the current product service system of a generator set distributor. A PPIAF framework and a SERVQUAL framework are adapted to assess product performance and service quality, respectively. AHP is used as …

Accuracy Improvement Of Pedestrian Trajectory Prediction By An Extended Kalman Filter And Pedestrian Behavior Classification, Jiayu Guo

Graduate Theses - Electrical and Computer Engineering

The objective of this thesis is to improve the accuracy of predicting motion trajectory, i.e., speed and direction, of a pedestrian in front of an Ego Vehicle which has a Mobileye camera with an advanced driver assistance system (ADAS). The Ego Vehicle captures and records videos of pedestrians in front of it, and these videos are analyzed to predict a pedestrian trajectory from instantaneous, random actions of a pedestrian. Instant actions include, but are not limited to, walking at a constant speed, sudden accelerations/decelerations, sudden dodging from the Ego Vehicle, sudden advancements to the Ego Vehicle, sudden withdrawals or sudden …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Cmos Radioactive Isotope Identification With Multichannel Analyzer And Embedded Neural Network, Samuel Murray

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A radiation detection and identification system is designed and implemented to perform gamma ray spectroscopy on radioactive sources and identify which isotopes are present in the sources. A multichannel analyzer is implemented on an ASIC to process the signal produced from gamma rays detected by a scintillator and photomultiplier tube and to quantize the gamma ray energies to build a histogram. A fast, low memory embedded neural network is implemented on a microcontroller ASIC to identify the isotopes present in the gamma ray histogram produced by the multichannel analyzer in real time.

Advisors: Sina Balkir and Michael W. Hoffman