Engineering Commons^™

Open-Source Tig-Based Metal 3d-Printing, Shane Oberloier

Dissertations, Master's Theses and Master's Reports

Metal 3-D printing has been relegated to high-cost proprietary high-resolution systems and low-resolution low-cost metal inert gas (MIG) systems. In order to provide a path to high-resolution, low-cost, metal 3-D printing, this manuscript proposes a new open source metal 3-D printer design based around a low-cost tungsten inert gas (TIG) welder coupled to a commercial open source self replicating rapid prototyper. Optimal printing parameters for the machine are acquired using a novel computational intelligence software. TIG has many advantages over MIG, such as having a low heat input, clean beads, and the potential for both high-resolution prints as well as …

Coordination, Adaptation, And Complexity In Decision Fusion, Weiqiang Dong

Dissertations

A parallel decentralized binary decision fusion architecture employs a bank of local detectors (LDs) that access a commonly-observed phenomenon. The system makes a binary decision about the phenomenon, accepting one of two hypotheses (H0 (“absent”) or H1 (“present”)). The k 1 LD uses a local decision rule to compress its local observations yk into a binary local decision uk; uk = 0 if the k 1 LD accepts H0 and uk = 1 if it accepts H1. The k 1 LD sends its decision uk over a noiseless dedicated channel to a Data Fusion Center (DFC). The DFC combines the …

Drone-Assisted Emergency Communications, Di Wu

Dissertations

Drone-mounted base stations (DBSs) have been proposed to extend coverage and improve communications between mobile users (MUs) and their corresponding macro base stations (MBSs). Different from the base stations on the ground, DBSs can flexibly fly over and close to MUs to establish a better vantage for communications. Thus, the pathloss between a DBS and an MU can be much smaller than that between the MU and MBS. In addition, by hovering in the air, the DBS can likely establish a Line-of-Sight link to the MBS. DBSs can be leveraged to recover communications in a large natural disaster struck area …

Countering Internet Packet Classifiers To Improve User Online Privacy, Sina Fathi-Kazerooni

Dissertations

Internet traffic classification or packet classification is the act of classifying packets using the extracted statistical data from the transmitted packets on a computer network. Internet traffic classification is an essential tool for Internet service providers to manage network traffic, provide users with the intended quality of service (QoS), and perform surveillance. QoS measures prioritize a network's traffic type over other traffic based on preset criteria; for instance, it gives higher priority or bandwidth to video traffic over website browsing traffic. Internet packet classification methods are also used for automated intrusion detection. They analyze incoming traffic patterns and identify malicious …

Possibilities And Challenges Of Radio Frequency Energy Harvesting In Dar Es Salaam, Tanzania, Fredrick Isingo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents investigation on the possibilities and challenges of harvesting ambient Radio Frequency Energy (RFE) at Dar es Salaam region in Tanzania. The Radio Frequency (RF) signals were measured using a Rohde and Schwarz FSC 3 spectrum analyzer observing available frequencies with their respective power. Among several RF signals received, the most powerful signals observed were; 800 MHz, 950 MHz, 2100 MHz and 2400 MHz, having average signal strengths of about-30.29 dBm,-35.94 dBm,-42.90 dBm and-30.42 dBm respectively. The power possessed within these frequencies were suitable to be harvested due to their signal strengths, an overall power average of-34.89dBm was …

User-Centred Scalable Big Data Visualizer For Power Consumption Data In The Electrical Secondary Distribution Network, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Establishment of Smart Grids for electrical power has been practised worldwide for the purpose of bringing reliability, security, and efficient management of electrical power networks for enhancing quality service to the society. Apart from the potential aim, smart grid has been a challenge to developing countries, including Tanzania from cost and technology point of view. Due to the use of many smart equipment involved in smart grids like Advanced Metering Infrastructure (AMI) equipped with smart meters and sensors, handling and managing big data has been a challenge. Among the challenges is the issue of visualizing the Big Data due to …

Neural Networks On An Fpga And The Exploration Of Hardware Friendly Activation Functions, Jiong Si, Sarah L. Harris, Evangelos Yfantis

Electrical & Computer Engineering Faculty Research

This paper describes our implementation of several neural networks built on a field programmable gate array (FPGA) and used to recognize a handwritten digit dataset—the Modified National Institute of Standards and Technology (MNIST) database. We also propose a novel hardware-friendly activation function called the dynamic Rectifid Linear Unit (ReLU)—D-ReLU function that achieves higher performance than traditional activation functions at no cost to accuracy. We built a 2-layer online training multilayer perceptron (MLP) neural network on an FPGA with varying data width. Reducing the data width from 8 to 4 bits only reduces prediction accuracy by 11%, but the FPGA area …

Comparative Analysis Of Multiplicative And Additive Noise Based Automated Regularizations In Non-Linear Diffusion Image Reconstruction, Chiza Christophe

Tanzania Journal of Engineering and Technology (TJET)

Multiplicative and additive noises are often introduced in image signals during the image acquisition process and result into degradation of image features. The work done by Perona and Malik in 1990 and its modified versions revolutionized the way through which noises or speckles are removed. The Perona-Malik model requires tuning of the regularization parameter to control and prevent staircase artifacts in restored images. The current manual tuning is a challenging and time consuming practice when a long queue of images is registered for processing. Attempt to automate the regularization parameter appeared in Perona-Malik model with self-adjusting shape-defining constant. Although both …

Direct Predictive Speed Control Of Salient Pmsm Drives In Constant Torque And Constant Power Regimes For Electric Vehicles Applications, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

A direct speed control of salient permanent magnet synchronous motor (PMSM) drives in constant torque and constant power regimes for electric vehicles applications is presented. The proposed speed control scheme is derived from model predictive control approach where both rotor speed and stator current are formulated in a single objective function that is periodically computed to attain the PMSM drive optimum switching states. The dynamic model of the PMSM intrinsically encompasses the unknown disturbance, which should be rejected for high-performance speed control especially in transient conditions. Consequently, the extended modified augmented state Kalman filter (ASKF) is incorporated in the proposed …

Potential For Increased Rural Electrification Rate In Sub-Saharan Africa Using Swer Power Distribution Networks, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Rural electrification rate (RER) in Africa is still low to date. Several countries in Sub-Saharan Africa have tried to address this problem using conventional single phase two-wire or three-phase three-wire systems, however at large costs due to the nature of dispersed rural load centres, low load demand, and low population density. Another solution of off-grid generation creates associated health problems. Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes intensive literature review to elucidate challenges and solutions to the implementation of SWER technology. Advantages of SWER technology …

Wind Power Integration And Its Impact On Power Quality-A Didactic Approach, Santos Kihwele Dr

Tanzania Journal of Engineering and Technology (TJET)

This paper presents a model of a wind power system integrated with realistic power system, with intention of using it in addressing power quality issues in relations to grid codes during steady-state operation transient-state operation i.e., presence of grid fault events. For that case, a didactic approach of the normal performance of power systems due to the connection of fixed-speed wind turbine with induction generators is used. A study of integrating wind farms will be presented, including the incidence of high inrush current due to switching capacitor banks, out-rush current and voltage sags due to nearby three phase faults. As …

Mimo Antenna For Fifth Generation Mm-Wave Applications: A Bibliometric Survey, Rajeshwari R. Malekar, Laxmikant K. Shevada, Hema D. Raut, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Nowadays most discussed technology is mm-wave and 5G communication. The requirement of 5G technology is high bandwidth, high data rate, and low latency. To fulfil these requirements for the current growth in mobile communication multiple input multiple output antenna is used. This bibliometric paper throws light on the various methods used to improve mutual coupling between multiple antennas. Various mutual coupling reduction techniques that are used in MIMO antennas like Dielectric resonator antenna, Electromagnetic Bandgap Structure, Neutralization lines, Defected Ground Structures, Metamaterial, etc. are explained. Scopus database is used for this bibliometric review on mm-wave MIMO 5G technology from the …

Bibliometric Review Of Mppt Algorithms For Wind Energy Conversion Systems, Jayshree Ashok Pande, Paresh Nasikkar

Library Philosophy and Practice (e-journal)

The existing conventional fuels are going up in prices and going down in availability. This has boosted the demand for renewable resources like wind energy. Wind energy being abundantly available is becoming very popular as it is a freely available pollution-free green energy. Some technical aspects like the tracking of maximum power from the wind energy conversion systems have a very high impact on the efficiency of the wind energy conversion systems. Several algorithms have been implemented for tracking the maximum power point of the wind energy conversion systems. The main objective of this paper is to study the extent …

A Bibliometric Survey On Ultra Wideband Multiple Input Multiple Output Antenna With Improved Isolation, Laxmikant K. Shevada, Hema D. Raut, Rajeshwari R. Malekar, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Ultra wideband (UWB) technology remains a viable choice for very high speed data communication in future applications involving large bandwidth. For boosting the data communication efficiency and to mitigate the multipath fading issue faced by UWB system with existing narrowband systems, Multiple Input Multiple Output (MIMO) antenna system is used along with UWB. Mutual coupling which must be smaller in value plays a vital role in deciding the efficiency of MIMO antenna and hence it becomes as important aspect. The mutual coupling reduction techniques of various UWB MIMO antennas are surveyed in this bibliometric paper. The bibliometric survey aims to …

Electronic Profiling Of Synthetic Dna Using Schottky Junctions, Souhad M.A Daraghma

Student Works (2020-2029)

Deoxyribonucleic acid (DNA) has attracted a lot of attention lately owing to the discovery of its semiconducting property and is considered as an interesting material that could find applications in nanotechnology and electronic devices. In-depth understanding of its charge transfer mechanism is however required for effective development of DNA-based technology. This unfortunately remains still a non-trivial task despite the numerous theoretical and experimental studies that have been conducted to date. The complexity of the previously employed methods, and their lack of accuracy has made it difficult to grasp the clear understanding of the electronic behaviors of the DNA molecules under …

Multibeam Array Antenna For Base Station In The Fifth-Generation Mobile Communication System, Intan Izafina Idrus

Student Works (2020-2029)

Research on the fifth-generation (5G) mobile communication system has been accelerated to meet the standardization of the International Telecommunications Union for higher data traffic and higher data rates. The main requirements of the 5G mobile communication systems are the utilization of millimeter waves, the deployment of small cells, and the use of multibeam array antennas for multiple-input multiple-output schemes. Multibeam array antennas play an important role in developing a new base station to enhance system capacity, improve network coverage, and reduce co-channel interference. The main objective of this thesis is to design a single-layer multibeam array antenna at 28 GHz …

Conditional Generative Adversarial Network Demosaicing Strategy For Division Of Focal Plane Polarimeters, Garrett Sargent, Bradley M. Ratliff, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

Division of focal plane (DoFP), or integrated microgrid polarimeters, typically consist of a 2 × 2 mosaic of linear polarization filters overlaid upon a focal plane array sensor and obtain temporally synchronized polarized intensity measurements across a scene, similar in concept to a Bayer color filter array camera. However, the resulting estimated polarimetric images suffer a loss in resolution and can be plagued by aliasing due to the spatially-modulated microgrid measurement strategy. Demosaicing strategies have been proposed that attempt to minimize these effects, but result in some level of residual artifacts. In this work we propose a conditional generative adversarial …

Evaluation Of Mechanical Properties Of Malaysia Local Source Wood For Electric Cruiser Board Applications, Mohamad Rosman Othaman

Student Works (2020-2029)

This research project revolves around the idea to reduce the carbon emission in mitigating the issue of climate change. An idea to introduce the electrical cruiser board by Muhammad Fiqkri Ismail from Universiti Kuala Lumpur with his idea to promote carbon less form of multimodal transportation for users in urban city of Greater Kuala Lumpur leads this research to study the elastic properties of local source woods in Malaysia that could be proposed for this application. The wood is used for the construction of the deck of cruiser board which designed three layers with the cross-ply laminate. Three types of …

Influence Of The Shaping Process On The Tensile Properties Of Steel Reinforcement Bars Carbon Steel Grades Bjtp24 And Bjts40, Nuraziz Handika, Ridha Amalia Idhar, Jessica Sjah, Essy Arijoeni, Elly Tjahjono

Makara Journal of Technology

According to the current applicable national standard in Indonesia, i.e. SNI 07 2529 1991, in addition to the limitation on the loading rate, the steel bar must be reduced, formed, or lathed, as part of the shaping process of samples. This study determined and compared the effect of the shaping process on the yield strength, ultimate strength, and percent elongation by conducting tensile tests of steel bar grade BJTS40, i.e. deformed bar type of steel, and grade BJTP24, i.e., plain bar type of steel. Three diameters of the deformed bar (BJTS40) and one diameter of the plain bar (BJTP24) were …

A Density Functional Theory Study On Using Montmorillonite To Reduce Air Pollution, Triati Dewi Kencana Wungu, Meqorry Yusfi, Suprijadi Suprijadi

Makara Journal of Technology

In this study, density functional theory (DFT) method is used to investigate the possibility of using a smectite clay mineral called montmorillonite (MMT) in reducing heavy metals, such as Cd, through Cd adsorption. The mechanism of Cd adsorption in MMT is observed theoretically, and the tetrahedrally isomorphic substitution on the upper layer of MMT is considered to observe the role of Al and Fe in strengthening Cd adsorption. Two types of MMT are modeled in this study: Al-MMT and Fe-MMT. The Al-MMT means that Al substitutes one atom in the upper tetrahedral layer of MMT, while Fe-MMT means that Fe …

Ionic Conductiviy Of Alginate-Nh4cl Polymer Electrolyte, Nurhasniza Mamajan Khan, Noor Saadiah Mohd Ali, Ahmad Faizrin Ahmad Fuzlin, Ahmad Salihin Samsudin

Makara Journal of Technology

This study aims to produce a solid biopolymer electrolyte (SBE) by doping ammonium chloride (NH4Cl) into alginate. Solution casting was used to prepare the alginate–NH4Cl SBE system. Electrical impedance spectroscopy was performed to analyze the electrical properties of the SBE under the applied frequency range of 50 Hz–1 MHz. The incorporation of 8 wt.% NH4Cl enhances the ionic conductivity of the SBE up to 3.18 × 10-7 S/cm at ambient room temperature. Fourier transform infrared spectroscopy shows that complexation occurs between the hydroxyl (-OH), carboxylate (COO-) and ether linkage (C-O-C) functional groups due to the formation of inter- and intra-molecular …

Use Of Viscoplastic Damper For Improving The Resistance Of Steel Frames To Blast Loading, Gholamreza Abdollahzadeh, Hadi Faghihmaleki, Hamed Hamidi Jamnani, Atefeh Ebrahimi Bardar

Makara Journal of Technology

In this paper, we evaluated the effect of viscoplastic dampers on the response of steel frames under blast loading. We used SAP2000 software and link elements to investigate the responses of nine-story steel frames with and without dampers. The proposed viscoplastic damper is a new type of viscous damper. The application of this damper is based on the availability of its constituent materials. The damper acts as a viscoelastic damper at low levels of vibration, but it acts as a combination of viscoelastic operator and metal-yielding device at extreme levels of vibration. With respect to the height of the structure, …

Influence Of Lithium Bromide On Electrical Properties In Bio-Based Polymer Electrolytes, Ahmad Faizrin Fuzlin, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

This research presents the influence of lithium bromide (LiBr) on the electrical properties of alginate in bio-based polymer electrolytes (BBPEs) system. Bio-based alginate was prepared using the solution casting technique with various LiBr compositions. The ionic conductivity and electrical properties of the prepared BBPEs samples were studied using electrical impedance spectroscopy over a frequency range of 50 Hz–1 MHz. A maximum ionic conductivity of 7.46 × 10−5 S cm-1 was obtained for a sample containing 15 wt. % lithium bromide-doped alginate BBPEs at ambient temperature (303 K). The electrical analysis revealed that the most conductive sample based on alginate-LiBr BBPEs …

Mechanical Alloying-Assisted Coating Of Fe–Al Powders On Steel Substrate, Alfian Noviyanto, Sri Harjanto, Wahyu Bambang Widayatno, Agus Sukarto Wismogroho, Muhamad Ikhlasul Amal, Nurul Taufiqu Rochman

Makara Journal of Technology

The coating layer of Fe–Al powders on the steel substrate was prepared by mechanical alloying at room temperature. Fe, Al, and the steel substrates were milled with high-energy ball milling for 32 h with a ball-to-powder ratio of 8 in an argon atmosphere to prevent oxidation during milling. Although mechanical alloying was performed for 32 h, no new phases were observed after mechanical alloying, as analyzed by X-ray diffraction. However, the crystallite size of the milled powders for 32 h decreased by factor two compared with the initial powders. Scanning electron micrographs showed that the coating layers formed >8 h …

Performance Of Free-Space Optical Communication Systems Using Optical Amplifiers Under Amplify-Forward And Amplify-Received Configurations, Ucuk Darusalam, Arockia Bazil Raj, Fitri Yuli Zulkifli, Purnomo Sidi Priambodo, Eko Tjipto Rahardjo

Makara Journal of Technology

With the growth of digital technology in the stage of industrial revolution 4.0, the demand for broadcasting large amounts of information to last mile users has increased. Free-space optical (FSO) communication is one of the telecommunication platforms that has shown immense potential in meeting the demand for information broadcasting. In this work, the performance of FSO communication based on wavelength division multiplexing with a data rate of 80 Gbps is investigated through simulations. The configuration of optical amplifiers in the FSO system is set up on the basis of the amplify-forward and amplify-received configurations to expand the network. The investigation …

Iso 9001:2015 Risk-Based Thinking: A Framework Using Fuzzy-Support Vector Machine, Ralph Sherwin A. Corpuz

Makara Journal of Technology

Risk-based thinking (RBT) is one of the distinct new features of the International Organization for Standardization 9001:2015. Interestingly, the standard does not prescribe any tools. Hence, organizations are puzzled as to the extent of conformance. Some organizations have adopted formal tools. However, these tools seem insufficient in linking the standard into an evidence-based decision support system. To resolve gaps in RBT implementation, this paper proposes a framework based on fuzzy inference system (FIS) and support vector machine (SVM) to automate risk analysis and evaluation, proposal and verification of action plans, and prediction of the feasibility of risks and opportunities according …

Antenna Radiation Element Designs For 5g Applications, Zhijun Gui

Electrical Engineering Undergraduate Honors Theses

This thesis introduced the advantage of the fifth-generation network and gave examples to the three major classes of applications categorized by International Telecommunication Union-Radiocommunication Sector. In this work, a patch antenna and a board-band bow-tie antenna with microelectromechanical switch design were modified to meet 5G communication purposes. The revised patch antenna produced a minimum S11 of -57.92dB, a resonant frequency at the 28GHz, and bandwidth of 4.55GHz. The modified design meets the requirements for wireless communication purposes. During the duplication process of the board-band bow-tie antenna design, multiple discrepancies were found, and the proposed results were not able to achieve. …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

Speaker Prototyping Design, Andrew Lathe

Undergraduate Honors Theses

Audio design is a pertinent industry in today’s world, with an extremely large market including leaders such as Bose, Harman International, and Sennheiser. This project is designed to explore the processes that are necessary to create a new type of product in this market. The end goal is to have a functioning, high–quality set of speakers to prove various concepts of design and prototyping.

The steps involved in this project go through the entire design process from initial choice of product to a finished prototype. Processes include the selection of outsourced components such as drivers and necessary connectors. The design …

Transfer-To-Transfer Learning Approach For Computer Aided Detection Of Covid-19 In Chest Radiographs, Barath Narayanan Narayanan, Russell C. Hardie, Vignesh Krishnaraja, Christina Karam, Venkata Salini Priyamvada Davuluru

Electrical and Computer Engineering Faculty Publications

The coronavirus disease 2019 (COVID-19) global pandemic has severely impacted lives across the globe. Respiratory disorders in COVID-19 patients are caused by lung opacities similar to viral pneumonia. A Computer-Aided Detection (CAD) system for the detection of COVID-19 using chest radiographs would provide a second opinion for radiologists. For this research, we utilize publicly available datasets that have been marked by radiologists into two-classes (COVID-19 and non-COVID-19). We address the class imbalance problem associated with the training dataset by proposing a novel transfer-to-transfer learning approach, where we break a highly imbalanced training dataset into a group of balanced mini-sets and …