Engineering Commons^™

Using A Micro-Integrator To Eliminate The Numerical Butterfly Effect In Non-Linear Chaotic Partial Differential Equations, Joshua Jemegbe

Electrical Engineering Theses

Chaos theory is a relatively new scientific paradigm for the analysis, simulation and prediction of non-linear phenomena whose initial conditions determine the behavior of their entire time series representation. It finds many applications in mathematics, science, and engineering. These include, but are not limited, to data encryption and decryption, designing secure communication systems, predicting weather patterns, noise fluctuations on data lines, understanding turbulence in fluid flow, and analyzing quantum wells. Systems that exhibit chaos are called chaotic systems. In computing solutions to nonlinear chaotic partial differential equation sets, slight deviations in step size could lead to completely diverging trajectories as …

Compressive Sensing For Speech Signals In Mobile Systems, Sabir Ahmed

Electrical Engineering Theses

Compressive sensing is an emerging and revolutionary technology that strongly relies on the sparsity of the signal. In compressive sensing the signal is sparsely compressively sampled by taking a small number of random projections of the signal, which contain most of the salient information. Compressive sensing has been previously applied in areas like: image processing, radar systems and sonar systems. This research work will discuss the potential implementation of compressive sensing in mobile communication systems and how it will influence their data rates. In a typical mobile communication system, the signal of interest is sampled at least at the Nyquist …

The Extended Preferred Ordering Theorem For Radar Tracking Using The Extended Kalman Filter, Donald Leskiw

Electrical Engineering and Computer Science - Dissertations

A certain problem in nonlinear estimation exists in radar tracking. Usually radar detections provide instantaneous position measurements in radar (polar) coordinates at discrete times, while tracks (estimated positions and motions over continuous time) are determined in rectangular coordinates; and the linear Kalman filter (LKF) is used as the estimator. Less common, the LKF is used to determine the tracks in radar coordinates, which are then converted into rectangular coordinates. Rarely is the extended Kalman filter (EKF) used, where the tracks are directly determined in rectangular coordinates from the radar detections via a local linearization. And so most radar tracks tend …

Investigation Of A Floating Load Buck Dc-Dc Switching Converter, Hong Tan

Graduate Theses and Dissertations

A floating load buck DC-DC switching converter was analyzed, simulated, designed and prototyped. The floating load buck converter is first compared to the conventional buck converter. It was found that both the floating load buck converter and conventional buck converter exhibit similar conversion characteristics despite the differences in the placement of their output inductors. A floating load buck converter was designed to be used as a high-voltage off-line light-emitting diodes (LEDs) driver using a Texas Instruments' TPS92001 controller. Finally, the characteristics of this floating load buck converter LED driver were experimentally examined.

Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu

Graduate Theses and Dissertations

CMOS technology becomes important in Radio Frequency (RF) communication systems which include both a receiver and a transmitter. In a high performance radio receiver, the Low Noise Amplifier (LNA) is the first circuit, and its noise performance dominates the entire receiver. Depending upon the system in which they are used, LNAs can be designed according to various topologies and structures. The LNA needs to have matched input impedance, and at the same time it should amplify the small amplitude input signal without adding too much noise and still have the minimal power consumption. It also needs a good interface with …

Design Of An 866 Mhz On-Chip Frequency Synthesizer, Phaniraj Joshi

Graduate Theses and Dissertations

There is a strong need for stable frequency references with large tuning ranges in today's communication systems. While the crystal oscillators assure good frequency stability, it is not possible to achieve a large frequency range by tuning the passive components attached to them. Frequency synthesizers are usually used for this purpose because of their ability to produce a variety of output frequencies. The Phase Locked Loop (PLL) based frequency synthesizer is the most preferred of all types of synthesizers available because of its additional features like programmability, low noise and low cost as well as high accuracy and stability. The …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Work In Progress - Virtual Facilitation And Procedural Knowledge Education, Ray Luechtefeld, Steve Eugene Watkins

Electrical and Computer Engineering Faculty Research & Creative Works

Engineering students acquire both conceptual and procedural knowledge as part of their education. While conceptual knowledge, such as understanding why certain design practices are required or having knowledge of the general principles of engineering development, is essential, procedural knowledge to enact specific engineering practices is also needed. This kind of knowledge, such as balancing chemical equations, solving calculus problems, or finding Thevenin-Norton equivalents, is usually taught through rote problem solving, sometimes with the guidance of teaching assistants or aid from the instructor if students find themselves "stuck". However, a Virtual Facilitator, designed to help students develop team skills, can also …

Distributed Electrical Power System In Cubesat Applications, Robert Burt

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The cubesat spacecraft was conceived over ten years ago. Since that time, close to 100 cubesat satellites have either been launched or are in the process of construction. Although started as an educational teaching tool, the cubesat is gaining popularity in the satellite industry and is making inroads as a standard architecture for many nano and pico satellite applications. The electrical power system for the cubesat class satellites almost exclusively conforms to a centralized architecture.

This thesis researches the potential of using a distributed architecture for the cubesat power system. There are several key advantages of a distributed architecture that …

Inkjet-Printed Highly Transparent Solar Cell Antennas, Jesus A. Arellano

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Small satellites, especially Cube Satellites (CubeSats), have become important vehicles for space exploration. One of the challenges CubeSats face is limited surface area. This limitation poses a question for antenna design–where to mount the antenna? Transparent antenna is a solution to resolve the competition between solar cells and antennas for surface area. The transparent antennas can be directly integrated on top of solar cells without requiring additional space. It is for this reason that this thesis focuses on the integration of highly transparent meshed antenna with solar cells. Even though transparent antennas allow light to travel light through them, they …

Wiihopp, Jeff Christian, Ben Hoselton, Derek Simon

Mechanical Engineering

Childhood obesity is becoming a growing problem in the United States. According to the CDC, childhood obesity has more than tripled in the past 30 years [7]. It can lead to health problems previously reserved for adults, such as diabetes, high blood pressure, and high cholesterol. For the team WiiHopp project, we plan to turn a JumpSport mini-trampoline into a controller for the Nintendo Wii console. The hope is to help turn the problem of video games and the laziness surrounding them into an active solution to combat the problem of childhood obesity.

Our goal is to produce an add-on …

Subthreshold 3 Phase Mixers, Jesus Angel Torres

Theses and Dissertations - UTB/UTPA

This thesis will discuss subthreshold FET mixers with a focus on conversion loss derivations. To begin understanding the mixers, a look into the FET model is first taken in Chapter II. Then in Chapter III, a single FET device mixer is studied and its conversion loss is found from its small-signal model. The chapter will then include a two FET device mixer and a four device FET mixer. Finally a new type of mixer will be discussed in Chapter IV. The new type of mixer is a 3 phase mixer with the phase angles being 0°, 120°, and 240°. The …

Radio Frequency Micro/Nano-Fluidic Devices For Microwave Dielectric Property Characterizations, Chunrong Song

All Dissertations

In this dissertation, a number of different topics in microwave dielectric property measurements have been covered by a systematic approach to the goals of development of dielectric spectroscopy and study of its high electric field effects with integrated on-chip microwave microfluidic / nanofluidic devices.
A method of parasitic effects cancellation for dielectric property measurement is proposed, analyzed, and experimentally evaluated for microwave characterization of small devices and materials that yield low intensity signals. The method dramatically reduces parasitic effects to uncover the otherwise buried signals. A high-sensitive radio frequency (RF) device is then developed and fabricated to detect small dielectric …

Using Practical Supergain For Passive Imaging With Noise, Martin Siderius

Electrical and Computer Engineering Faculty Publications and Presentations

Recent work has shown that endfire beamforming of ocean noise can be used to produce images of the seabed layering [Siderius et al., J. Acoust. Soc. Am. 120, 1315–1323 (2006)]. This initial noise imaging technique used conventional beamforming and was later extended to adaptive beamforming that is theoretically optimal. However, there can be problems with adaptive methods, which include extreme sensitivity to random errors, the required averaging time, and computational complexity. Here, the concept of supergain is used to show that delay and sum beamforming can produce nearly the same results as the optimal adaptive methods without the drawbacks.

Decomposition Of Reversible Logic Function Based On Cube-Reordering, Martin Lukac, Michitaka Kameyama, Marek Perkowski, Pawel Kerntopf

Electrical and Computer Engineering Faculty Publications and Presentations

We present a novel approach to the synthesis of incompletely specified reversible logic functions. The method is based on cube grouping; the first step of the synthesis method analyzes the logic function and generates groupings of same cubes in such a manner that multiple sub-functions are realized by a single Toffoli gate. This process also reorders the function in such a manner that not only groups of similarly defined cubes are joined together but also don’t care cubes. The proposed method is verified on standard benchmarks for both reversible and irreversible logic functions. The obtained results show that for functions …

The Performance Of Serial, Matched-Filter Packet Acquisition Using Transmit And Receive Antenna Diversity, Shivram Ramanathan

All Theses

The performance of serial, matched-filter acquisition is evaluated for asynchronous packet radio communications using transmit or receive antenna diversity. Transmit diversity is achieved using dual antenna transmissions of orthogonal preamble sequences and receive diversity is achieved using dual antenna reception of a single preamble sequence. Sequential test statistics are formed using non-coherent combining of the outputs from the orthogonal preamble matched-filters if transmitter diversity is used; the test statistics are formed using non coherent combining of the outputs from the preamble matched-filter in each receiver chain if receiver diversity is used. Threshold-based acquisition of the test statistics using both fixed …

Application Of Genetic Algorithm For Synthesis Of Large Reversible Circuits Using Covered Set Partitions, Maher Mofeid Hawash, Baker Abdalhaq, Amjad Hawash, Marek Perkowski

Electrical and Computer Engineering Faculty Publications and Presentations

We present the results of application of Evolutionary Algorithms to the problem of synthesizing quantum circuits which belong to the class of reversible circuits, represented as an input/output mapping vectors. The paper specifically focuses on large quantum circuits where many valid solutions exist in an exponentially inflating search space. Valid solutions represent the set of all input vector permutations (arrangements) which satisfy the circuit specification. The search space for circuits with large number of variables grows exponentially making it impossible to discover the set of optimal solutions. The paper compares three methods for selecting valid solutions of input vector sequences: …

New Analytical Bounds On The Probability Of Code-Word Error For Convolution Codes With Viterbi Decoding, Shweta Tomar

All Theses

New analytical bounds are developed for the probability of code-word error in a communication system with convolutional coding and soft-decision Viterbi decoding. The bounds are applicable to communications in channels with asynchronous interferers which are modeled as independent, partial-time white Gaussian interference sources. This model is often used in simulations to reflect the circumstances encountered in many packet radio communication networks. The new results include both purely analytical bounds and offline-simulation-aided bounds that permit implementation of accurate communication-link models with much lower online computational and storage requirements than are required with traditional Monte Carlo simulations of link performance. They significantly …

Digitally Controlled, Modular Electronic Load, Jason L. March

Master's Theses

This project entails the design and development of a digitally controlled, modular electronic load. The proposed load is unique from existing designs because it has the added ability to increase its maximum current level by adding identical modules in parallel. Each module is designed to sink a maximum of 5A at 60V but more modules allow for more current. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace, whenever possible, the resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well …

Analysis Of Contrast Enhancement Methods For Infrared Images, Sprinkle Christian

Master's Theses

Contrast enhancement techniques are used widely to improve the visual quality of images. The difference in luminance reflected from two adjacent surfaces creates contrast between the surfaces in the image. The greater the contrast, the easier it is to recognize and differentiate objects in an image. Thus object contrast is an important factor in the perception of the visual quality of an image and in its usefulness for object recognition and image analysis applications.

The focus of this thesis is on studying how well different contrast enhancement techniques developed for visible spectrum photographic images work on infrared images; to determine …

Modeling And Analysis Of A Four-Switch Buck-Boost Dynamic Capacitor, Oscar Plasencia

Master's Theses

Modern electric power utilities are facing a variety of challenges introduced by the increasing complexity of their operation, structure, and consumer loads. One such challenge has been to supply the ever growing demand for reactive power which is essential for grid support. For this reason dynamic VAR technologies are becoming much more important to modern day power systems. A recent dynamic VAR technology known as the Dynamic Capacitor offers full quadrant capacitive VAR control through the combination of AC/AC buck and boost cells. This paper introduces a new topology deemed the “Four-Switch Buck-Boost Dynamic Capacitor” which promises to combine the …

Enhancement Of Light Absorption Efficiency Of Solar Cell Using Dual, Ashton Ellaboudy

Master's Theses

In this research we study the effect of adding a single diffraction grating on top of a solar cell. We simulated the square diffraction grating, as well as triangular diffraction grating. The single square grating showed more favorable results, achieved 330% power improvement compared to 270% power improvement in the single triangular grating case.

We simulated a triangle/triangle (top-bottom) and triangular/rectangular (top-bottom) grating cases. The Triangular grating achieved higher light absorption compared to rectangular grating. The best top grating was around 200nm grating period. We realized solar cell efficiency improvement about 42.4% for the triangular rectangular (top-bottom) grating.

We studied …

Development Of A Simulation Tool For Analysis Of Freeway Crashes Due To Cell Phone Usage, Sourabh Sriom

UNLV Theses, Dissertations, Professional Papers, and Capstones

Research shows that drivers are susceptible to numerous distractions while driving which can be held responsible as the reason of a crash. Usage of cell phones, i.e. talking or texting while driving is considered one of the prominent distractions which causes a crash. This dissertation aims to study the number of crashes occurring on the freeways and their relation with the drivers of these cars using cell phones while they are driving. Since crashes occur relatively less frequently, the study of crashes is done using what is called the "rare event" theory. Java based simulations are done to model a …

A Study Of A Novel Modular Variable Geometry Frame Arranged As A Robotic Surface, Christopher James Salisbury

UNLV Theses, Dissertations, Professional Papers, and Capstones

The novel concept of a "variable geometry frame" is introduced and explored through a three-dimensional robotic surface which is devised and implemented using triangular modules. The link design is optimized using surplus motor dimensions as firm constraints, and round numbers for further arbitrary constraints. Each module is connected by a passive six-bar mechanism that mimics the constraints of a spherical joint at each triangle intersection. A three dimensional inkjet printer is used to create a six-module prototype designed around surplus stepper motors powered by an old computer power supply as a proof-of-concept example.

The finite element method is applied to …

Cooperative Sensing Using Reconfigurable Sensor Networks, Raúl Ordóñez

Raúl Ordóñez

No abstract provided.

Wideband Voltage Variable Attenuator With Fewer Components, Chin-Leong Lim

Chin-Leong Lim

RF/microwave amplifying devices have unit-to-unit gain variability. So, in some critical applications such as the low noise amplifier (LNA) in cellular basestations, the gain has to be adjusted in production using a voltage-variable attenuators (VVA). Constant impedance VVAs such as the PI and the bridged-TEE topologies require between 14 to 18 components, including 2 to 4 active devices, but their large dynamic (attenuation) range is wasted in this amplifier gain adjustment application. To create a more economical and smaller VVA for amplifier gain adjustment, we investigated a new circuit configuration comprising one active and four passive components. This paper describes …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

The Electrochemical Properties Of Cathode Materials Limxv3-Xo8, Hui Yang, Gang-Gang Zhao, Juan Li

Journal of Electrochemistry

The cathode material of LiMxV3-xO8 was fabricated by sol-gel method using citric acid as a chelating agent and doping transition metal ions M (Mn, Ti, Co and Ni). The structure, morphology and electrochemical proprieties of the LiMxV3-xO8 samples were investigated by XRD, TGA/DTA, SEM, charge-discharge and CV measurements. The results showed that different calcining temperatures result in different structures and morphologies, which lead to different discharge capacities. The specific discharge capacity of the sample calcined at 500℃ for 6 h was up to 300.4 mAh/g in the first cycle, and the capacity decreased with the increasing of calcining temperature. The …