Engineering Commons^™

Maize Nitrogen Uptake, Grain Nitrogen Concentration And Root-Zone Residual Nitrate Nitrogen Response Under Center Pivot, Subsurface Drip And Surface (Furrow) Irrigation, Suat Irmak, Ali T. Mohammed, Matthew Drudik

Department of Agricultural and Biological Systems Engineering: Faculty Publications

While the impact(s) of irrigation and nitrogen (N) levels on crop yields have been investigated separately, research lacks about how different irrigation methods coupled with different N application timing strategies under full and limited irrigation levels effect yield, soil nitrate nitrogen (NO₃-N) residual and stover N uptake. Knowledge of these dynamics can help to establish effective water and N management guidelines for the same crop under different irrigation methods and irrigation levels. This research investigated maize (Zea mays L.) residual soil NO₃-N concentration and stover and grain N uptake response to water under different irrigation …

Recent Developments In Timber Design & Its Impact On Carbon Emissions, Raquel Jackson

Spectra Undergraduate Research Journal

This paper explores recent developments in timber building designs and its potential towards reducing carbon emissions. Carbon dioxide emissions are a growing issue worldwide as urbanization and industrialization continues to increase. The rising concentration of carbon dioxide emissions pose significant concerns towards public welfare and environmental health. Despite current methods to reduce greenhouse gasses, carbon emissions remain difficult to reduce from steel and concrete industries. Increasing timber use in building design is a possible solution. Increasing more timber in building design can help reduce carbon emissions due to the carbon-absorbing properties of the construction material. Timber as a construction material …

Digital Education And Training Inventory, Ken Thomas, Robin Stubbs, Emily Shakespeare, Theresa Marie Greiwe

Tools

As the construction industry continues to evolve and increasingly embraces digitisation, an early-stage deliverable for Build Digital Project was to conduct a horizon scan of the opportunities available for those within the construction sector. A primary aim, therefore, is to provide a comprehensive inventory of educational and training provisions that exist within Ireland at present.

The resulting searchable inventory focuses on key educational sectors including Universities, Educational Training Boards (ETBS), Colleges of Further Education, Professional bodies and similar organisations.

Supporting The Delivery Of Information Management And Bim In Ireland: Learnings From Selected International Regions, Alan Hore, Ciaran Mcnally, Adekunle Qudus Adeleke, Wahib Saif

Reports

The Executive Summary introduction the report recommendations for Build Digital with respect to information management and the use of BIM as a critical vehicle of innovation to unlock improved project outcomes in construction.

Rejuvenation Effect Of Aged Sbs-Modified Asphalt Utilizing Molecule Analysis, Ke Shi, Feng Ma, Jenny Liu, Zhen Fu, Ruimeng Song, Dongdong Yuan, Chen Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Performance of Styrene-Butadiene-Styrene Modified Asphalt (SBSMA) is Significantly Impacted by its Aging and Regeneration. in This Research, the Molecular Dynamics Simulation Was Utilized to Investigate the Rejuvenation Effect of Active Reagents on Aged SBS Modified Asphalt through the Following Tasks: 1) Verifying the Accuracy of the Asphalt Model by Density and Solubility Parameters; 2) Assessing the Changes in the Rejuvenated Asphalt Model's Energetic Parameters and Volume Parameters, 3) Studying the Interaction Energy between SBS Molecules and Asphalt Molecule Models, and 4) Evaluating the Relative Concentration, Interfacial Interaction Energy, and Diffusion Effect of the Asphalt-Asphalt Models. the Results Indicated that …

Nonlinear Impact-Echo Test For Quantitative Evaluation Of Asr Damage In Concrete, Clayton Malone, Hongbin Sun, Jinying Zhu

Department of Civil and Environmental Engineering: Faculty Publications

Nonlinear acoustic methods demonstrate high sensitivity for concrete damage evaluation. Among these methods, nonlinear resonance acoustic methods have been widely used in laboratory tests on small scale test samples. In this study, a nonlinear impact-echo (IE) method was proposed for concrete damage evaluation, in which the IE frequency shift was measured at different impact force levels. The nonlinear IE test is similar to the nonlinear impact resonance acoustic spectroscopy (NIRAS) test in the experimental setup and analysis method. How- ever, the nonlinear IE test excites a local thickness resonance mode of a member instead of the global resonance vibration. Therefore, …

Nonlinear Impact-Echo Test For Quantitative Evaluation Of Asr Damage In Concrete, Clayton Malone, Hongbin Sun, Jinying Zhu

Department of Civil and Environmental Engineering: Faculty Publications

Nonlinear acoustic methods demonstrate high sensitivity for concrete damage evaluation. Among these methods, nonlinear resonance acoustic methods have been widely used in laboratory tests on small scale test samples. In this study, a nonlinear impact-echo (IE) method was proposed for concrete damage evaluation, in which the IE frequency shift was measured at different impact force levels. The nonlinear IE test is similar to the nonlinear impact resonance acoustic spectroscopy (NIRAS) test in the experimental setup and analysis method. How- ever, the nonlinear IE test excites a local thickness resonance mode of a member instead of the global resonance vibration. Therefore, …

Toward Low Carbon Footprint And Lightweight Masonry Alkali-Activated Material, Zina Ebrahim, Mohammad Mastali, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

The portland cement concrete industry and the masonry industry are undergoing changes in response to skilled labor shortages and concerns over climate and pollution. There may be interest from parts of the industry in lower carbon footprint and lightweight masonry products. Toward this aim, the use of hemp shiv--the woody core of the hemp plant--in alkali-activated concrete was investigated herein and shown to have a wide range of impacts on the hardened state characteristics of a material suitable for structural concrete masonry units (CMUs) in accordance with ASTM C90 requirements. Hemp shiv is well known for its use in hempcrete, …

Evaluating The Feasibility Of Bioenergy Production From Single And Mixed Beverage Waste And Sewage Sludge Through An Integrated Hydrothermal Liquefaction-Anaerobic Digestion System, Oluwayinka Michael Adedeji

Theses and Dissertations

Beverage waste and sewage sludge are two of the most generated waste-based biomasses. Recent interest in the hydrothermal liquefaction (HTL) of these wastes pointed to the generation of a byproduct of high dissolved organic carbon [also called aqueous co-product (ACP)]. However, ACP is being discarded which not only increases the environmental footprints of the HTL process but also results in reduced bioenergy potential. Hence, anaerobic digestion (AD) is touted as an effective utilization process of ACP for further bioenergy recovery. This study evaluated the feasibility of producing bioenergy (biocrude and biomethane) from the combination of beverage waste and sewage sludge …

The Association Between Drought Exposure And Respiratory-Related Mortality In The United States From 2000 To 2018, Yeongjin Gwon, Yuanyuan Ji, Jesse E. Bell, Azar M. Abadi, Jesse D. Berman, Austin Rau, Ronald D. Leeper, Jared Rennie

Daugherty Water for Food Global Institute: Faculty Publications

Climate change has brought increasing attention to the assessment of health risks associated with climate and extreme events. Drought is a complex climate phenomenon that has been increasing in frequency and severity both locally and globally due to climate change. However, the health risks of drought are often overlooked, especially in places such as the United States, as the pathways to health impacts are complex and indirect. This study aims to conduct a comprehensive assessment of the effects of monthly drought exposure on respiratory mortality for NOAA climate regions in the United States from 2000 to 2018. A two-stage model …

The Use Of Point Cloud Data To Support Concrete Bridge Deck Condition Assessment, Issa Nidal Al Shaini

Theses and Dissertations

Bridge deck condition assessments are typically conducted through visual physical inspections, utilizing traditional contact sensors for Non-Destructive Evaluation techniques such as hammer Sounding and chain dragging which require the expertise of trained inspectors. However, the accuracy of these inspections is limited by the level of deterioration of the bridge deck, as the ability of the inspectors is proportional to the apparent level of damage. This study aims to improve the accuracy of bridge deck inspection processes by utilizing non-destructive evaluation techniques, including the analysis of point cloud data gathered via Light Detection and Ranging (LiDAR) as a geometry-capturing tool. The …

Concise Summary Of Existing Correlations With Thermophysical Properties Of Seawater With Applications: A Recent Review, Furqan Jamil, Hafiz Muhammad Ali, Mehdi Haji Khiadani

Research outputs 2022 to 2026

Physical and thermal specifications of seawater are used by researchers and engineers in different fields. Accordingly, a vast array of literature has been devoted to developing different correlation equations for calculating seawater characteristics. This review presents a concise investigation of various physical and thermal specifications of seawater including: density, boiling point and vapor pressure, osmotic coefficient and pressure, surface tension, thermal conductivity, viscosity, specific enthalpy, specific entropy, specific heat capacity, isothermal compressibility, isobaric expansivity and Gibbs energy. Further to this, apsects of temperature, salinity and pressure have a significant influence on these properties, and will also be considered here. The …

Experimental Testing And Constitutive Modelling Of Pavement Materials, Xueyan Liu, Yuqing Zhang, Zhanping You, Linbing Wang, Changhong Zhou

Michigan Tech Publications, Part 1

Pavement materials such as asphalt mixtures, granular aggregates and soils exhibit complex material properties and engineering performance under external loading and environmental conditions [...].

Experimental Testing And Constitutive Modelling Of Pavement Materials, Xueyan Liu, Yuqing Zhang, Zhanping You, Linbing Wang, Changhong Zhou

Michigan Tech Publications, Part 1

No abstract provided.

Spatiotemporal Variability In Total Dissolved Solids And Total Suspended Solids Along The Colorado River, Godson Ebenezer Adjovu, Haroon Stephen, Sajjad Ahmad

Civil and Environmental Engineering and Construction Faculty Research

The Colorado River is a principal source of water for 40 million people and farmlands in seven states in the western US and the Republic of Mexico. The river has been under intense pressure from the effects of climate change and anthropogenic activities associated with population growth leading to elevated total dissolved solid (TDS) and total suspended solid (TSS) concentrations. Elevated TDS- and TSS-related issues in the basin have a direct negative impact on the water usage and the ecological health of aquatic organisms. This study, therefore, analyzed the spatiotemporal variability in the TDS and TSS concentrations along the river. …

A High-Speed Portable Ground Heat Exchanger Model For Use In Various Energy Simulation Software, Ryan Davies, Matt Mitchell, Edwin Lee

Macalester Journal of Physics and Astronomy

A portable component model (PCM) of a ground source heat pump system was developed and used as a test case in the creating of a PCM development framework. By developing this framework, new building energy simulation models will be able to be easily integrated into existing simulation software such as EnergyPlus and the Modelica Buildings Library. Our model uses a time responsive g-function and numerical methods to simulate ground source heat pumps for single time steps as well as long time scales. We validated our model against GHESim and GLHEPro and found that our model agrees with these two standards …

Influence Of Support Attachment Pattern On The Out-Of-Plane Buckling Capacity Of Steel Deck, Divyansh R. Kapoor, Brian Bogh, Kara D. Peterman

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

Diaphragms (Figure 1) serve as a critical component of a building's lateral force resisting system (LFRS), transferring lateral loads from the façade of the structure to the designated vertical lateral force resisting system. Design guidance for profiled steel diaphragm panels can be found in AISI S310 - 20 (AISI 2020) and SDI DDM04 (Luttrell 2015) and are controlled by connection limit states or buckling limit states. Deck connectivity with the underlying frame can either be fully attached (For example 36/7), i.e. connected through the bottom of each flute, or partially attached (for example 36/5 or 36/4) where not all the …

Alkali-Silica Reaction Mitigation Using Alternative Supplementary Cementitious Materials, Craig Newtson, Judit M. Garcia, Seyedsaleh Mousavinezhad

Data

Over the past few decades, Class F fly ash has been widely used in concrete as a supplementary cementitious material (SCM) due, in part, to its ability to mitigate alkali-silica reaction (ASR). However, future availability of fly ash is uncertain as the energy industry shifts towards renewable sources, resulting in the closure of coal-burning power plants. Therefore, there is a growing need to find alternatives to fly ash that are both cost effective and environmentally friendly. This study aimed to evaluate the effectiveness of ground-granulated blast furnace slag (GGBFS), metakaolin, and a locally available natural pozzolan mined from a pumicite …

Accelerated Sulfate Attack Testing For Concrete, Craig Newtson, Seyedsaleh Mousavinezhad, William Toledo, Federico Aguayo

Data

Extensive research has been conducted on sulfate attack of concrete structures, however, the need to adopt use of more sustainable materials is driving a need for a quicker test method to assess sulfate resistance. Class F fly ash, which is a byproduct of coal combustion for electricity generation, has historically been used in concrete mixtures to improve sulfate resistance. However, environmental considerations and evolving energy industry has decreased its availability, requiring the identification of economically viable and environmentally friendly alternatives to fly ash. Another challenge in addressing sulfate attack durability issues in concrete is that the standard sulfate attack test …

Alkali-Silica Reaction Mitigation Using Alternative Supplementary Cementitious Materials, Craig Newtson, Judit M. Garcia, Seyedsaleh Mousavinezhad

Publications

Over the past few decades, Class F fly ash has been widely used in concrete as a supplementary cementitious material (SCM) due, in part, to its ability to mitigate alkali-silica reaction (ASR). However, future availability of fly ash is uncertain as the energy industry shifts towards renewable sources, resulting in the closure of coal-burning power plants. Therefore, there is a growing need to find alternatives to fly ash that are both cost effective and environmentally friendly. This study aimed to evaluate the effectiveness of ground-granulated blast furnace slag (GGBFS), metakaolin, and a locally available natural pozzolan mined from a pumicite …

Accelerated Sulfate Attack Testing For Concrete, Craig Newtson, Seyedsaleh Mousavinezhad, William Toledo, Federico Aguayo

Publications

Extensive research has been conducted on sulfate attack of concrete structures, however, the need to adopt use of more sustainable materials is driving a need for a quicker test method to assess sulfate resistance. Class F fly ash, which is a byproduct of coal combustion for electricity generation, has historically been used in concrete mixtures to improve sulfate resistance. However, environmental considerations and evolving energy industry has decreased its availability, requiring the identification of economically viable and environmentally friendly alternatives to fly ash. Another challenge in addressing sulfate attack durability issues in concrete is that the standard sulfate attack test …

Investigating Disparities And Safety Equity In Pedestrian Nighttime Crashes In Michigan, Sia Isaria Mwende

Masters Theses

For the past eleven years (2011 - 2021) in Michigan, 76 percent of all fatal pedestrian crashes occurred at night. Over the same period, about 36 percent of pedestrian nighttime crashes were fatal or incapacitating (KA), while only 25 percent of daytime pedestrian crashes were fatal or incapacitating (KA). Previous studies suggest that, overall, poor neighborhoods and racial minorities are associated with more pedestrian crashes. With more fatal and incapacitating pedestrian crashes occurring at night, it is imperative to examine how these crashes are distributed by economic status and racial makeup. Therefore, this study aims to investigate the racial and …

Assessing Boil Water Notices As Health-Risk Communication: Risk Perceptions, Efficacy, And Compliance During Winter Storm Uri, Ashleigh M. Day, Sydney O'Shay, Khairul Islam, Matthew W. Seeger, Shawn P. Mcelmurry

Open Data at Wayne State

Winter Storm Uri was an extreme disaster that impacted much of the United States during February of 2021. Texas and Oklahoma were generally not prepared for such an event and experienced massive power grid failures. This led to cascading risks including water system disruptions and many boil water notices (BWNs). The breakdown of some communication channels and the inability to enact protective actions due to power outages, as well as travel limitations on public roads, complicated both dissemination and implementation. Under these conditions, a non-representative, cross-sectional, survey was collected to assess individuals experience BWNs and how perceived efficacy impacts compliance. …

Freeze-Thaw Damage Assessment Of Engineered Cementitious Composites Using The Electrochemical Impedance Spectroscopy Method, Ru Bai, Shuguang Liu, Changwang Yan, Ji Zhou, Lihe Lu, Lin Li

Civil and Architectural Engineering Faculty Research

The mechanical properties of engineered cementitious composites (ECC) in service in cold regions can be significantly degraded by periodic freezing and thawing. In this work, the damage degree of freeze–thaw of ECC was systematically assessed by using the electrochemical impedance spectroscopy (EIS) technique. In addition, Nuclear Magnetic Resonance (NMR) Relaxometry measurements were also performed to obtain pore structure parameters, and the uniaxial tensile tests were also carried out to analyse the tensile performance after freeze–thaw cycles. From the acquired results, it was demonstrated that the EIS behaviour of ECC varied with the freeze–thaw cycles. The diameter of the Nyquist curve …

Understanding The Flow Dynamics Of The Pearl River, Ms, Through Hydrodynamic Modeling, Nahruma Mehzabeen Pieu

Master's Theses

The Pearl River brings fresh water and nutrients into Lake Borgne regulating conditions for oyster growth in estuarine waters. However, there are no flow measurement stations installed on East Pearl or West Pearl either at the river outlets or after the upstream bifurcation of the Pearl. This study aims to model the Lower Pearl River to understand the flow dynamics in the major branches, and to determine the final outflow distribution into the Mississippi Sound, aiming to improve river forcing for ocean models studying estuarine dynamics of the Mississippi Sound.

Synthetic meandering bathymetry with updated banks is developed and applied …

Merging Multiple Existing Geotechnical Databases, Charlie Sun, Brad Rister, Eileen Grady

Kentucky Transportation Center Research Report

This report discusses a project undertaken by Kentucky Transportation Center (KTC) researchers to create a comprehensive geotechnical database for highway planning, design, maintenance, and repair. The project consolidated multiple geotechnical data sources into a unified database accessible to Kentucky Transportation Cabinet (KYTC) staff, enabling informed decision making and improving project outcomes. Databases were merged with great attention to detail, ensuring data integrity and coherence. A geotechnical data collector app developed as part of the project supports convenient and efficient data collection in the field, even when phones or tablets lack network connectivity. A rockfall rating app and landslide hazard rating …

Non-Steady-State Fickian Diffusion Models Decrease The Estimated Gel Layer Diffusion Coefficient Uncertainty For Diffusive Gradients In Thin-Films Passive Samplers, Samuel D. Hodges, David G. Wahman, Levi M. Haupert, Huong T. Pham, Margaret K. Bozarth, Michael B. Howland, Julian L. Fairey

Civil Engineering Faculty Publications and Presentations

Mass transport in diffusive gradients in thin-film passive samplers is restricted to diffusion through a gel layer of agarose or agarose cross-linked polyacrylamide (APA). The gel layer diffusion coefficient, D_Gel, is typically determined using a standard analysis (SA) based on Fick’s first law from two-compartment diffusion cell (D-Cell) tests. The SA assumes pseudo-steady-state flux, characterized by linear sink mass accumulation–time profiles with a typical threshold R² ≥ 0.97. In 72 D-Cell tests with nitrate, 63 met this threshold, but the SA-determined D_Gel ranged from 10.1 to 15.8 × 10^_–6 cm²·s^–1 (agarose) and …

Experimental Characterization And Computer Vision-Assisted Detection Of Pitting Corrosion On Stainless Steel Structural Members, Riley J. Muehler

Master's Theses

Pitting corrosion is a prevalent form of corrosive damage that can weaken, damage, and initiate failure in corrosion-resistant metallic materials. For instance, 304 stainless steel is commonly utilized in various structures (e.g., miter gates, heat exchangers, and storage tanks), but is prone to failure through pitting corrosion and stress corrosion cracking under mechanical loading, regardless of its high corrosion resistance. In this study, to better understand the pitting corrosion damage development, controlled corrosion experiments were conducted to generate pits on 304 stainless steel specimens with and without mechanical loading. The pit development over time was characterized using a high-resolution laser …

Investigation Of Placement Of Polyethylenimine Within Thin Film Composite Reverse Osmosis Membranes For Enhanced Anti-Fouling Properties, Taylor F. Austin

Master's Theses

Fresh water scarcity is an alarming issue for communities across the globe. The development of water recycling and reuse technologies has become crucial in expanding the limited water resources. Reverse osmosis (RO) is among the key processes that can treat wastewater to meet potable water reuse standards. Despite the advancements in RO membrane technologies, many challenges persist regarding the operation and maintenance of RO membranes, such as membrane fouling. Extensive research investigations have focused on developing RO membrane modifications to combat the decreased performance due to fouling. Polyethylenimine (PEI) is a promising polymer used for enhancing the anti-fouling properties of …

Sustainability In Concrete Masonry With Natural Pozzolans, Ceiley L. Davis

Architectural Engineering: Graduate Reports

To achieve greater sustainability in masonry construction for the Western market it is common to replace masonry grout's partial cement content with waste pozzolans. As waste pozzolans are in limited supply, as the coal burning market in the West diminishes, this research investigates viable grout mixtures which replace cement with Natural Pozzolans, a more plentiful sustainable replacement. The present work investigated the percentage of Natural Pozzolans that can be partially substituted for cement for grout mixtures to achieve an axial compressive strength of 2000psi within 28 and 56 days of curing. To determine efficacy per ASTM 476-22, “Standards Specifications for …