Engineering Commons^™

Low-Voltage Ride-Through Capability Improvement Of Type-3 Wind Turbine Through Active Disturbance Rejection Feedback Control-Based Dynamic Voltage Restorer, El M. Boulaoutaq, Asma Aziz, Abdelmounime El Magri, Ahmed Abbou, Mohamed Ajaamoum, Azeddine Rachdy

Research outputs 2022 to 2026

Disconnections due to voltage drops in the grid cannot be permitted if wind turbines (WTs) contribute significantly to electricity production, as this increases the risk of production loss and destabilizes the grid. To mitigate the negative effects of these occurrences, WTs must be able to ride through the low-voltage conditions and inject reactive current to provide dynamic voltage support. This paper investigates the low-voltage ride-Through (LVRT) capability enhancement of a Type-3 WT utilizing a dynamic voltage restorer (DVR). During the grid voltage drop, the DVR quickly injects a compensating voltage to keep the stator voltage constant. This paper proposes an …

Semi-Annual Progress Report #12, Missouri University Of Science And Technology. Inspire - University Transportation Center

Semi-Annual Progress Reports

No abstract provided.

Designing A Model Of Solar Photovoltaic Water Pumping System For Off-Grid Localities In Tanzania, Imani Mruma

Tanzania Journal of Engineering and Technology (TJET)

Modeling of photovoltaic (PV) water pumping system for rural water localities is vital especially in these modern days, in Tanzania. This is due to the rise of high number of solar-powered rural water projects constructed lacking appropriate design. The fate result into poor and substandard projects delivering below expectations. Kikombo Solar Water Project situated in Dodoma; Tanzania is one among poorly designed solar project chosen as a case study to validate proposed model. The main problem of Kikombo project is unsatisfactory amount of water from domestic points to satisfy population demand. This matter has been raised by pumping-station attendants and …

Assessment Of Spatial Variability Of Groundwater Potential Using Remote Sensing And Gis-Based-Criteria Evaluation For Dar Es Salaam, Tanzania, Augustina Alexander

Tanzania Journal of Engineering and Technology (TJET)

Groundwater is an important resource for the continuous provision of water supply in both urban and rural areas. Lack of enough knowledge about the spatial variability of groundwater potential zones (GWPZS) has a negative impact on groundwater extraction development and management and may result into over exploitation. In this study, analytic hierarchy approach (AHP)-coupled with multi criteria decision analysis (MCDA) and GIS techniques were employed to integrate hydrogeological, geological as well as topographical data to assess spatial variability of groundwater potential zones of Dar es Salaam city. Seven thematic layers such as lithology, slope, land-use, lineament, drainage, soil, and rainfall …

Extraction And Characterization Of Fibres From The Bark Of Ficus Nekbudu Tree, Liberato V Haule

Tanzania Journal of Engineering and Technology (TJET)

This paper investigates the extraction and characterization of fibres from the bark of the ficus nekbudu tree. The Ficus Nekbudu Fibres (FNF) was extracted from the bark by retting in water and then treatment with sodium hydroxide solution. The extracted FNF was analysed for chemical composition, physical, tensile, surface, structural and thermal stability properties. Findings on the chemical composition indicated that FNF has cellulose (49.9 %), lignin (13.4%), ash (7.1%) and water content (8.1%). From the physical investigation it was found that FNF has density (1.42 ± 0.005 g/cm3) and moisture regain (9.2 ±0.3%). From mechanical investigation it was found …

Assessing Spatio-Temporal Variations And Trends Of Rainfall Over Somalia From 1991 To 2020, Paul Ts Limbu Sr

Tanzania Journal of Engineering and Technology (TJET)

This study aims to examine the spatiotemporal variability and trends of rainfall over Somalia using the Mann-Kendall (MK) test and Sen’s slope estimator to investigate the trend and magnitude of the rainfall changes and the arithmetic mean and coefficient of variation (CV) to examine the rainfall variability. To achieve this aim, the gridded monthly satellite rainfall datasets from Climate Hazards Group InfraRed Precipitation with Station (CHIRPS) for the period between 1991 and 2020 were used. Results show that annual rainfall generally exhibits bimodal rainfall distribution, March to May (Gu) and September to November (Deyr), though southern coastal regions receive extended …

Retraining Investment For Alberta’S Oil And Gas Workers For Green Jobs In The Solar Industry, Theresa K. Meyer, Carol Hunsberger, Joshua M. Pearce

Michigan Tech Publications

If oil sands are to be eliminated from the energy market to protect the global environment, human health and long-term economic welfare, a significant number of workers will be displaced in the transition to renewable energy technologies. This study outlines a cost-effective and convenient path for oil and gas workers in Alberta to be retrained in the burgeoning solar photovoltaic (PV) industry. Many oil and gas workers would be able to transfer fields with no additional training required. This study examines retraining options for the remainder of workers using the most closely matching skill equivalent PV job to minimize retraining …

Application Of Mangrove Timber In Reinforcing Concrete, John K. Makunza Jkm

Tanzania Journal of Engineering and Technology (TJET)

Use of mangrove timber beams for supporting floor slabs in historic buildings in Zanzibar Stone Town is still applied although the available structural data on mangrove timber is inadequate. This concern has called for an investigation on the structural properties of mangrove timber, so that the information obtained could help to establish the structural strength of the existing floor slabs in historic buildings. Hence, mangrove timber specimens were sampled from Zanzibar, and tested in the laboratory for their strengths in tension, compression and shear. The test results showed that mangrove is a hardwood timber of strength class D70, the highest …

Vulnerable Road User Safety: Data Collection, Analysis, And Countermeasures, Anahita Kakhani

Theses and Dissertations

The safety of pedestrians and bicyclists (vulnerable road users) has become a paramount global concern, especially with a 53% and 31% surge in related crashes over the past decade in the U.S. Despite transportation agencies implementing various safety measures to address this issue, the number of severe injuries among these road users continues to climb annually. This underscores the urgent need for innovative methodologies and technologies to pinpoint the factors compromising their safety. To do so, this study aimed to introduce and employ techniques and countermeasures to gain deeper insight into risks faced by vulnerable road users. This study includes …

Modeling Leaf-Level Transpiration: Exploring The Consequences Of Assumed Saturated Vapor Pressure In Leaves, Danlyn L. Brennan

Dissertations and Theses

Understanding the dynamics of water transport through leaf intercellular airspaces (IAS) and its impact on transpiration is crucial for accurate predictions of plant water use and ecosystem response to changing climates. This study investigates the implications of assuming undersaturation of water vapor in the IAS for transpiration predictions and explores potential modifications to standard modeling approaches.

A dynamic 1D soil-plant-atmosphere continuum using a stomatal optimization model (SPAC-SOT) framework was used to simulate the response of tree species, P. edulis, to prolonged drought and varying environmental conditions. Comparisons between two model assumptions (saturated vs. undersaturated IAS) reveal notable differences in …

Developing A Smart And Sustainable Public Transportation System: A Case Study In Camden, New Jersey, Zahra Vafakhah

Theses and Dissertations

The transportation sector is a major contributor to air pollution and Greenhouse Gas (GHG) emissions. As a significant source of emissions, public transportation presents an opportunity for mitigation through electrification. However, transitioning to an electric bus fleet necessitates substantial investments in bus procurement and charging infrastructure. To address the associated costs, this study introduces a mixed-integer linear mathematical model developed to optimize the location of on-route fast charging stations within bus networks. The central objective of this optimization formulation is to minimize the overall cost of establishing the charging infrastructure. The study employs a real-world case study focusing on a …

Simultaneous 3d Construction And Imaging Of Plant Cells Using Plasmonic Nanoprobe-Assisted Multimodal Nonlinear Optical Microscopy, Kun Liu, Yutian Lei, Dawei Li

Department of Civil and Environmental Engineering: Faculty Publications

Nonlinear optical (NLO) imaging has emerged as a promising plant cell imaging technique due to its large optical penetration, inherent 3D spatial resolution, and reduced photodamage; exogenous nanoprobes are usually needed for nonsignal target cell analysis. Here, we report in vivo, simultaneous 3D labeling and imaging of potato cell structures using plasmonic nanoprobe-assisted multimodal NLO microscopy. Experimental results show that the complete cell structure can be imaged via the combination of second-harmonic generation (SHG) and two-photon luminescence (TPL) when noble metal silver or gold ions are added. In contrast, without the noble metal ion solution, no NLO signals from the …

Simultaneous 3d Construction And Imaging Of Plant Cells Using Plasmonic Nanoprobe-Assisted Multimodal Nonlinear Optical Microscopy, Kun Liu, Yutian Lei, Dawei Li

Department of Civil and Environmental Engineering: Faculty Publications

Nonlinear optical (NLO) imaging has emerged as a promising plant cell imaging technique due to its large optical penetration, inherent 3D spatial resolution, and reduced photodamage; exogenous nanoprobes are usually needed for nonsignal target cell analysis. Here, we report in vivo, simultaneous 3D labeling and imaging of potato cell structures using plasmonic nanoprobe-assisted multimodal NLO microscopy. Experimental results show that the complete cell structure can be imaged via the combination of second-harmonic generation (SHG) and two-photon luminescence (TPL) when noble metal silver or gold ions are added. In contrast, without the noble metal ion solution, no NLO signals from the …

Common Ground Newsletter Fall 2023, Missouri University Of Science And Technology

Common Ground

- Free-Format Education

- S&T student selected as national ASCE ambassador

- Heart of a servant

- Exploring history, architecture of Chicago

Thermotolerance And Hydrogen Production Potential Of Salt-Tolerant Microflora From Salt Fields, Tsuyoshi Imai, Gede Adi Wiguna Sudiartha, Jantima Teeka, Prapaipid Chairattanamanokorn, Alissara Reungsang, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Upper mesophilic temperature acclimation of halophilic, hydrogen-producing bacteria from salt fields was investigated in this study, along with the changes in microbial abundance during anaerobic digestion (AD) process. Genomic approaches such as PCR-denaturing gradient gel electrophoresis (DGGE) and next-generation sequencing (NGS) were performed to profile the microbial communities. During AD, there was a significant abundance of Halanaerobacter lacunarum at 48°C followed by the increase in hydrogen yield, signifying potential contribution from the halophile in the hydrogen production. A decrease in the dominance of H. lacunarum and Halanaerobium fermentans at 42°C, likely due to an increase in other bacterial species, was …

Evaluation Of Digital Twin Approaches For Thermal Modeling And Energy Optimization For Existing Buildings, Jason Bastie Muermann

Theses and Dissertations

Residential, commercial, and industrial building sectors in the United States were responsible for 42% of the nation’s consumption of 100.2 quadrillion BTUs of energy in 2019 [1]. 80% of the nation’s energy is sourced from fossil fuels, including coal, natural gas, and petroleum. Fossil fuels are known contributors to carbon emissions and climate change, making energy reduction vital. Consequently, New Jersey Department of Military and Veterans Affairs (NJDMAVA) is tasked with evaluating energy consumption and efficiency in all New Jersey Army National Guard (NJARNG) facilities, as mandated by TAG Policy Letter 18-5, Executive Order 13990, and the Energy Independence and …

Robotic Inspection Of Infrastructure Using Vision, Gpr, And Impact-Echo Sensors, Jizhong Xiao

INSPIRE Archived Webinars

Bridges, dams, highways, and tunnels in the U.S. are reaching their life expectancy, and thus have imperative needs for routine inspection and maintenance to ensure sustainability. It is reported that 42% of over 600,000 highway bridges in the National Bridge Inventory (NBI) have exceeded their design life of 50 years, and 42,951 bridges are rated in poor condition and classified as "structurally deficient". To inspect the structurally integrity of bridges, the inspectors also need to detect subsurface defects (i.e., delamination, voids) using NDE instruments such as GPR and impact-echo (IE) device at difficult to access components (i.e., pier, bottom side …

Dual Activation Of Peroxymonosulfate Using Mnfe2O4/G‑C3N4 And Visible Light For The Efficient Degradation Of Steroid Hormones: Performance, Mechanisms, And Environmental Impacts, Kitipong Poomipuen, Chainarong Sakulthaew, Chanat Chokejaroenrat, Athaphon Angkaew, Kanidrawee Techauay, Thapanee Poompoung, Kanokwan Teingtham, Piyaporn Phansak, Piyangkun Lueangjaroenkit, Daniel D. Snow

Daugherty Water for Food Global Institute: Faculty Publications

Single activation of peroxymonosulfate (PMS) in a homogeneous system is sometimes insufficient for producing reactive oxygen species (ROS) for water treatment applications. In this work, manganese spinel ferrite and graphitic carbon nitride (MnFe₂O₄/g-C₃N₄; MnF) were successfully used as an activator for PMS under visible light irradiation to remove the four-mostdetected- hormone-contaminated water under different environmental conditions. The incorporation of g-C₃N₄ in the nanocomposites led to material enhancements, including increased crystallinity, reduced particle agglomeration, amplified magnetism, improved recyclability, and increased active surface area, thereby facilitating the PMS activation and electron …

Social Vulnerability Of The People Exposed To Wildfires In U.S. West Coast States, Arash Modaresi Rad, John T. Abatzoglou, Erica Fleishman, Miranda H. Mockrin, Volker C. Radeloff, Yavar Pourmohamad, Megan Cattau, J. Michael Johnson, Philip Higuera, Nicholas J. Nauslar, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Understanding of the vulnerability of populations exposed to wildfires is limited. We used an index from the U.S. Centers for Disease Control and Prevention to assess the social vulnerability of populations exposed to wildfire from 2000–2021 in California, Oregon, and Washington, which accounted for 90% of exposures in the western United States. The number of people exposed to fire from 2000–2010 to 2011–2021 increased substantially, with the largest increase, nearly 250%, for people with high social vulnerability. In Oregon and Washington, a higher percentage of exposed people were highly vulnerable (>40%) than in California (~8%). Increased social vulnerability of …

Barriers To Bim Implementation For Cost Management In The Irish Construction Industry, Uchenna Sampson Igwe Dr, Alan Hore Dr, Dermot Kehily Dr., David Colmenero Lechuga

Conference Papers

Building Information Modeling (BIM) is the foundation of digital transformation in the architecture, engineering, and construction (AEC) industry that enables efficient collaboration and information sharing among stakeholders in the industry. It has been identified as a powerful tool for construction cost management because it provides accurate and timely information about the cost implications of design decisions. BIM development in Ireland is expected to continue growing in the coming years, driven by the proposed 2024 government mandate, continued state supports and the benefits that BIM brings to the construction industry, including improved collaboration, reduced errors and waste, and increased efficiency. Notable …

An Investigation Into Ireland’S Bim Skills Gap, Guadalupe Centanni, Barry Mcauley

Conference Papers

The adoption of digital skills within the Irish AEC Sector has the potential to enhance efficiency and competitiveness among its stakeholders. Despite this opportunity, there is still a high demand for skilled BIM professionals, which cannot be currently met. To meet this skills demand and directly target future skills gaps within Ireland, several challenges must be addressed to facilitate broader BIM adoption. This paper focuses on addressing this gap by identifying steps to be followed to develop skilled professionals within BIM. This has been achieved by investigating the extent to which construction stakeholders in Ireland comprehend BIM and, examiningthe training …

Accelerating Bim Adoption In Ireland: A Ten-Year Review Of Cita Bim Gathering Proceedings, Alan Hore, Roger West, Barry Mcauley

Conference Papers

Digital construction interfaces have been studied extensively over the last few decades, with an ever-grow- ing catalogue of publications. The CitA BIM Gathering conferences have played a key role in bringing together the research and industry communities ina collaborative setting over the past decade in Ireland. In this paper the authors systematically review 10 years of papers published in the BIM Gathering pro- ceedings since the inaugural conference in 2013. A total of 175 papers involving over 200 authors have been reviewed and classified under the 2018 World Economic Forum (WEF) recommendations in respect to ac- celerating BIM adoption. The …

The Development Of A Lean Digital Construction (Bim) Innovation Framework For Irish Construction Smes, Marina Andreou, Barry Mcauley, Alan Hore

Conference Papers

The adoption of Building Information Modelling (BIM) within small and medium-sized enterprises (SMEs) must overcome several challenges to succeed. Potential barriers include the need for financial resources, correct BIM guidance, and training. In recent years, SME organisations have investigated how the complementary application of BIM and Lean principles can maximise digital construction practices. For this approach to be successful, structured guidance is paramount. This paper presents the results from an extensive literature review that explores BIM and Lean capabilities, focusing on synergies and existing frameworks. Based on the results from the literature review, the paper suggests an experimental framework that …

Optimization Of Removal Of Toluene From Industrial Wastewater Using Rsm Box– Behnken Experimental Design, Dariush Jafari, Morteza Esfandyari, Mehdi Mojahed

Department of Civil and Environmental Engineering: Faculty Publications

The study is concerned with the adsorption of toluene from real wastewater using granular beads of activated carbon. The adsorbent was analyzed before and after the process using Scanning Electron Microscope analysis to characterize its surface characteristics. The adsorption parameters including solution pH, contact time, dosage of adsorbent, temperature and toluene initial concentration were optimized using response surface methodology (RSM) Box-Behnken experimental design to maximize the toluene adsorption. The adsorption capacity of the adsorbent was 298 mg g⁻¹ and the maximum toluene removal was 99.5% which was achieved in the following optimal conditions: pH: 2, 100 min, adsorbent dosage: …

Optimization Of Removal Of Toluene From Industrial Wastewater Using Rsm Box– Behnken Experimental Design, Dariush Jafari, Morteza Esfandyari, Mehdi Mojahed

Department of Civil and Environmental Engineering: Faculty Publications

The study is concerned with the adsorption of toluene from real wastewater using granular beads of activated carbon. The adsorbent was analyzed before and after the process using Scanning Electron Microscope analysis to characterize its surface characteristics. The adsorption parameters including solution pH, contact time, dosage of adsorbent, temperature and toluene initial concentration were optimized using response surface methodology (RSM) Box-Behnken experimental design to maximize the toluene adsorption. The adsorption capacity of the adsorbent was 298 mg g^{− 1} and the maximum toluene removal was 99.5% which was achieved in the following optimal conditions: pH: 2, 100 min, adsorbent …

Industry Colloquium Report, Robert Moore

Reports

In the ever-evolving landscape of the construction industry, digital transformation has emerged as a pivotal force reshaping the way projects are conceived, executed, and delivered. This transformation, fuelled by cutting-edge technology and innovative practices, holds the promise of greater efficiency, sustainability, and collaboration within the construction sector.

This report offers a comprehensive summary of the Build Digital Project colloquium. It provides actionable insights and recommendations for clients, supply chain partners, and for prioritisation within the Build Digital Project pillars. As the industry partners seek to build a more efficient, sustainable, and collaborative construction sector, understanding and harnessing the invaluable insights …

Feasibility Study Of Pavement Rutting Evaluation Method Based On Driving Vibration, Zhang Jinxi, Wang Peirong, Cao Dandan, Ceng Jingxiang

Journal of China & Foreign Highway

To explore the intelligent detection and monitoring methods of pavement performance, this paper utilized the self-developed driving data collection app to collect vibration acceleration and other data of the pavement during driving, and carried out the feasibility study of evaluating the pavement rutting by driving vibration. Firstly, the collected vibration acceleration data was processed for noise reduction, and the driving vibration characteristics in different working conditions were analyzed. Secondly, seven time domain indicators with high correlation between vibration acceleration and the rutting were extracted as the initial set of indicators, and the seven indicators were downscaled into two independent principal …

Influence Of Shear Deformation On Manufacturing And Erection Alignment, Wang Jin, Chen Changsong

Journal of China & Foreign Highway

This paper aims to study the effect of shear deformation on the manufacturing and erection alignment of main girders of free cantilever erection steel box girder bridges and better design the state of bridge formation state. To this end, it calculated the shear stress coefficient of uniformity of the steel box girder’s cross-section by adopting the finite element method and conducted comparison with the solid model of the plate and shell units of the steel box girder. The results show that the shear stress coefficient of uniformity calculated by finite element software is accurate and reliable. Additionally, simple modeling indicates …

Study On Temperature Gradient Of Long-Span Single-Box Double-Chamber Box Girder Bridge, Yang Wenbin

Journal of China & Foreign Highway

In view of the complex temperature effect of the single-box double-chamber box girders, this paper aimed to carry out the temperature gradient study of box girder cross-sections by employing a short-tower single-box double-chamber cable-stayed bridge with span arrangement of (120+120) m. 21 temperature sensors were installed at the cross-sections of large-mileage closure sections, with the set collection frequency of one time per hour and a wireless collection module for data collection. Meanwhile, temperature observation was carried out for a period of 171 d to obtain the distribution law of the temperature gradient in cross-sections of the closure sections. The study …

Experimental Study On The Influence Of Cantilevered Sidewalk On The Wind Resistance Of A Cable-Stayed Bridge With Pk Girder, Yu Zhenghua

Journal of China & Foreign Highway

Bilateral box steel main girders are widely employed in large-span double-plane cable-stayed bridges. These bridges are characterized by low frequency, small damping, and relatively light mass, and their wind resistance stability is a key problem to be solved in bridge construction. By taking the Pingnan super major cable-stayed bridge with a main span of 636 m on Pingrong Expressway under construction as the research project, this paper built a finite element spatial model of the bridge and analyzed the structural modal characteristics. Meanwhile, it carried out the main girder segmental model of elastically suspended vortex vibration and chatter vibration wind …