Engineering Commons^™

Frequency Up-Conversion Electromagnetic Energy Harvester For Generating Electrical Power From Vibration Of Beams Under Moving Load, Md Ismail Monsury, Adamaris Sanchez, Mohsen Amjadian, Constantine Tarawneh

Civil Engineering Faculty Publications

This paper studies a single-resonator electromagnetic energy harvester that employs an impact-driven frequency up-conversion mechanism to convert low-frequency vibrations of a multi-span beam, subjected to successive moving loads, into electrical power. The harvester consists of a cantilever beam made of plastic, serving as the resonator, with a thick square copper coil attached to its free end. This coil moves relative to two stationary cubic neodymium permanent magnets, each positioned on one side of the coil. To expand the harvester’s operational bandwidth, a stopper is positioned beneath the resonator, inducing controlled mechanical impacts as the cantilever beam vibrates. These impacts effectively …

Calculating The Radius Of The Earth Using Sunset Method: Comparison With Al-BīRūNi Method, Jana Kamal, Tayeb Brahimi

Effat Undergraduate Research Journal

This paper attempts to compare the earth's radius calculation based on the sunset or sunrise (moonset or moonrise) with the Method developed by the scientist Al-Bīrūni. The sunset sunrise method is used to calculate the earth radius by standing in front of a flat horizontal plane. In addition, the authors have use Al-Bīrūni's rule to calculate the radius. Furthermore, the error percent of both Al-Bīrūni and the sunset sunrise method were calculated as well. The results showed that the earth actual radius is 6371 km. Eratosthenes radius which is 6366 km is the closest to the actual earth radius, then …

Spatial Distribution Of The Bankfull Discharge Recurrence Interval Across Tennessee, Usa, Brayden P. Flanagan

Honors Theses

Stream restoration and water resources engineers use a wide variety of hydrological tools and refer to multiple databases to determine accurate watershed and stream characteristics required for site assessment and restoration projects. Regional curves provide significant watershed and stream data that stream restoration engineers use in various restoration projects. However, developing these curves is time-consuming, costly, and complex, as data collection and validation require extensive field studies at multiple sites within the restoration areas. This study evaluates whether pertinent information on regional curves and streamflow frequency could be combined to provide practical guidance on determining design peak flow discharges for …

Utilizing Uae Date Palm Leaf Ash In Removing Ammoniated Compounds From Reject Brine After The Solvay Process, Hend Mohammed Alsheryani

Thesis/ Dissertation Defenses

This study addresses the critical challenge of managing ammonia-laden reject brine from desalination plants in the United Arab Emirates (UAE), where desalination is the primary freshwater source. The environmental impact of brine disposal, particularly ammonia contamination, necessitates the development of sustainable treatment solutions. This research explores the potential of date palm leaf ash (DPLA), an agricultural byproduct, as a low-cost and eco-friendly adsorbent for ammonia removal, aligning with the UAE’s sustainability and circular economy goals. The study evaluates the ammonia adsorption capacity of DPLA and optimizes its performance through thermal ashing at 750°C and chemical activation using calcium oxide (CaO), …

Enhancing Asphalt Mix Design Through Film Thickness And Bailey’S Gradation Method, Lydia Quinn

Civil Engineering Undergraduate Honors Theses

Contemporary asphalt research aims to strike a balance between rutting and fatigue cracking to enhance pavement longevity. The performance of asphalt mixtures is influenced by factors such as aggregate gradation and asphalt film thickness. Although gradation typically adheres to the mid-gradation method, asphalt film thickness is included in certain mix designs, even though it is not universally regarded as an essential parameter. Nonetheless, no current method primarily addresses both gradation and asphalt film thickness together. In this research, aggregate gradations were designed using the principles of Bailey’s method along with various other criteria such as control points, the dust to …

A Statistical Investigation Of The Parameters Influencing Rutting And Cracking Performance In Asphalt Mixtures, Alexis Light

Civil Engineering Undergraduate Honors Theses

Durable pavement is essential for modern transportation infrastructure, especially in the United States of America which boasts over 8.5 million lane miles of roads and highways. Despite advanced construction techniques, asphalt pavements are susceptible to rutting and cracking, significantly affecting their performance and maintenance costs. Current methods for analyzing rutting and cracking in asphalt mixtures rely on various parameters, leading to measurement variability. This highlights the need for more rigorous analysis to explore the relationship between mix design variables and pavement performance. This research explores the IDEAL-CT and APA data from 171 mix designs collected by the Arkansas Department of …

Toxicity And Biodegradability Of Novel Boronium Vs Conventional Ammonium Based Anti Microbial Compounds In Wastewater Treatment Systems, Noor Shalan

Poster Presentations

Quaternary ammonium compounds (QACs) are highly effective as disinfectants, herbicides, and pesticides; thus, overuse causes elevated levels of residual toxicity in domestic and industrial wastewater. QACs can be toxic to essential bacteria breaking down pollutants in wastewater treatment plants (WWTPs) and can remain untreated in effluent, harming the environment, and contributing to antibiotic resistance, posing risks to human health. Novel boronium-based antimicrobial compounds have demonstrated efficacy in eliminating bacteria, fungi, and viruses. If the boronium compounds exhibit lower residual toxicity, they could offer a promising alternative to QACs. Because these compounds are still in development, their potential toxicity to the …

Ghosts In Glass: Ghost Crabs (Ocypode Quadrata) As Judges Of Glass Sand For Coastal Restoration, Emily Parrish

Poster Presentations

Coastal erosion is heavily impacting coastal ecosystems across the Gulf. For instance, the state of Louisiana loses a football field worth of land every 100 minutes (Couvillion, 2017). The drastic loss of coastline highlights the dire need for restoration in the Northern Gulf Coast. An unexpected solution to this sediment loss may solve two major environmental issues at once by diverting millions of tons of glass waste from entering America’s landfills each year. By crushing glass to create sand and gravel for coastal restoration, we may generate a consistent and sustainable source of substrate. Our goal is to determine the …

Effect Of Beam Bracing On The Seismic Performance Of Laterally Skewed Reduced Beam Section Moment Connections With Composite Concrete Slabs, Pratik Ghimire

Graduate Theses and Dissertations

Existing experimental reduced beam section (RBS) moment frame investigations, particularly those used for prequalification in AISC-358, consider orthogonally oriented beam-to-column connections. While the design commentary provided in AISC-358 references recent skewed SMF numerical studies and potential performance effects when a lateral beam skew is introduced, limited experimental studies have been performed to verify the numerical findings. This study presents an experimental investigation into the cyclic behavior of RBS special moment frames that have lateral skew at the beam-to-column connection and composite concrete slabs. In this study, a skewed composite double-sided RBS connection is tested, having beam bracing outside the RBS …

Mechanical Properties And Microstructural Characteristics Of Hydrated Bcsa Cement At Extreme Temperatures, Behzad Farivar

Graduate Theses and Dissertations

Belitic Calcium Sulfoaluminate (BCSA) cement is an alternative binder known for its rapid setting and high early strength, making it ideal for applications such as fast-track construction and repair. This study presents a comprehensive investigation into the behavior of BCSA cement under a wide range of curing temperatures, with emphasis on early-age strength development, admixture effects, and the use of the maturity method for strength prediction.

The research evaluates BCSA cement performance in both hot and cold environments, ranging from approximately -28.9 °C (-20°F) to 49 °C (120°F). In warm climates, citric acid was used as a set retarder to …

Beyond The Hard Hat: Examining Barriers Of Women In Construction, Allison Pham

2025 Spring Honors Capstone Projects - Archive

The construction industry is falling behind in female representation, with women only making up 11.2% of the industry. The existing labor shortage is further exacerbated by the limited interest among women to pursue a career in construction. The purpose of this research is to investigate the factors that contribute to the lack of women in the construction industry and explore how HR strategies can attract and retain women in construction careers. Environmental, Social, and Governance (ESG) reports from three different industries were used to analyze the percentage of men and women employees. Multivariate regression analyses were conducted to examine whether …

Laboratory Performance Evaluation Of Hot Mix Asphalt Mixtures With Incorporations Of Different Recycled Plastic Additives Using The Dry Method, Alvaro A. Cerdas Murillo

All Theses

Asphalt pavements are susceptible to distresses such as cracking, rutting, and moisture damage, which reduce service life and increase maintenance costs. This study evaluated the use of recycled materials from HDPE and LDPE plastics (shredded and pelletized) and PET fibers of two lengths as asphalt mixture additives to provide a sustainable approach to improve performance. The materials were incorporated into two control mixtures designed with the Balanced Mix Design (BMD) method. Laboratory testing assessed cracking and rutting resistance, moisture susceptibility, abrasion resistance, and dynamic modulus across a range of conditions.

Results showed that PET fibers improved cracking resistance due to …

Community Wastewater Treatment Resilience Assessment, Tristan Veal

All Theses

With the rising threat of climate change and cascading impacts from infrastructure failure there is a growing need to strengthen community resilience. Theoretical and practical resilience frameworks are available, but they vary in aim and scope; there is no standard tool to assess resilience. This research expands on the resilience matrix (RM) application methods of previous research completed by the United States Army Corps of Engineers (USACE) and Clemson University. That work focused on drinking water treatment systems and developed a few dozen specific indicators, or metrics, to quantify resilience. This research adds wastewater infrastructure with the aim of identifying …

Hickory Street Square Revitalization, Spencer Knight, Grace Dungan, Tim Kula, Evan Lauritsen, Lindsey Mennenga

Honors Program: Senior Projects (Public)

The Hickory Street Square Revitalization Project seeks to transform a central public space in Sidney, Nebraska into a dynamic, community-oriented area that supports local events, economic activity, and cultural heritage. The project addresses six core objectives: 1) convertible street design, 2) parking lot reconfiguration, 3) public amenities, 4) event flexibility, 5) lighting and signage, and 6) old electric plant renovation. A conceptual design was developed by the design team (S.T.E.E.L. Sentinel Solutions) by synthesizing the most effective features of three preliminary alternatives, shaped further through community feedback and evolving project constraints. The final project design minimizes disruption to existing activity …

Stop Design: Rethinking The Approach To Public Transit's Architecture, Elizabeth M. Nielsen

Architecture Masters of Science Program: Theses

Public spaces are the foundation of our social health and wellbeing, but are often designed without considering the needs of the public, creating spaces that people do not feel encouraged to use. Just as public space design as a whole often falls short of serving the public, the same can be said for a subset of public space design, public transit stops. While they are public spaces created for the purpose of waiting, their design rarely reflects this.

Well-designed public transit stops are capable of both maintaining existing ridership and drawing in new riders. Most commonly, this design occurs at …

Experimental Study Of Novel Bcsa Scc Repair Materials And Implications On Corrosion In Bcsa Concrete Structures, Elizabeth S.M. Poblete

Graduate Theses and Dissertations

Some current building codes for structural concrete allow the use of alternative cement concrete if their structural, durability, and fire performance can be shown to be comparable to portland cement (PC) concrete. One such alternative cement, belitic calcium sulfoaluminate (BCSA) cement, is a promising standalone replacement for portland cement given its lower global warming potential (GWP), fast setting time, and high early age compressive strength. These properties also make it an ideal repair material. But repair materials often need to be highly flowable and easy to consolidate and their performance when used to repair PC concrete structures must be understood. …

Groundwater Storage Dynamics In Abu Dhabi Emirate Using In-Situ And Grace Data, Tala Jalal Maksoud

Theses

Water scarcity presents a significant challenge to the sustainable development; especially in arid regions like Abu Dhabi Emirate. Addressing concerns over nonrenewable aquifer depletion, caused by agricultural expansion and lifestyle advancements, has, therefore, become crucial in such regions. This thesis investigates Groundwater Storage (GWS) dynamics in Abu Dhabi Emirate by integrating satellite data from the Gravity Recovery and Climate Experiment (GRACE) with in-situ data from 257 wells over two decades (2002-2022), employing GIS and RS technologies. The main aim of this study is to provide a comprehensive approach to evaluate GWS dynamics considering multiple perspectives including: dealing with missing datasets, …

Performance Evaluation Of Highly Modified Asphalt-Based Binders In High Friction Surface Treatment: Comparative Study With Epoxy-Based System, Alireza Roshan, Magdy Abdelrahman, Mohyeldin Ragab

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

High Friction Surface Treatments (HFSTs) are frequently used to increase skid resistance and reduce collisions, particularly in crash-prone zones, including horizontal curves and intersections. Epoxy-based binders traditionally have been the sole option for HFSTs, but their drawbacks, such as high costs and compatibility challenges, have led to the search for substitute binders, including asphalt-based options. This study investigates the comparative performance of highly modified asphalt-based binders, including polymer-modified, mastic, and highly modified emulsions, in HFST applications using two aggregate types, Calcined Bauxite (CB) and Rhyolite with different gradations, with an emphasis on their frictional properties, durability, and resistance to polishing. …

Impacts Of Cognitive Workload On Veteran Driver Reaction Time: Predictive Modeling Using Bayesian And Machine Learning Methods, Kenneth Ofosu-Kwabe

All Theses

In high-demand environments, the ability to manage cognitive workload can mean the difference between optimal or safe performance and critical failure or accidents. Veterans face an elevated risk of fatal motor vehicle accidents due to post-deployment stress, combat-related injuries, and challenges readjusting to civilian driving. This study explores how cognitive workload affects reaction time performance using a driving simulator by collecting and analyzing subjective workload ratings (using the NASA-TLX survey), physiological signals from eye-tracking and performance data from a sample of 28 Veterans.

We examined how task difficulty, cognitive indicators and personal attributes influence reaction times across an interactive driving …

Bim-Based Automated System For Carbon Emissions And Construction Costs Estimation (Bas-Cc) In Modular Design And Production, Roshan Bandiwadekar

All Theses

Modular construction adopts a manufacturing-like construction process, enhancing the management of embodied carbon emissions in production and construction phases. However, estimating these emissions presents challenges due to the involvement of diverse stakeholders across various lifecycle stages. Additionally, cost considerations often influence design choices and material selections in modular constructions, neglecting the impact of embodied carbon emissions. To address these challenges, we present a proof-of-concept for an automated Building Information Modeling (BIM)-based system to estimate both carbon emissions and construction costs. This system automates the calculation of embodied carbon and cost implications of different modular designs and materials, enabling informed decision-making. …

Design And Optimization Of Aquaculture Gear: Development Of A Cage-Integrated Reeling Mechanism For Oyster Farming, Felicity Bryant

Honors Theses

This project encompasses the design, fabrication, and testing of a cage-integrated reeling system aimed at reducing the physical labor required in oyster aquaculture at Bama Bay Oyster Farm, the last operational oyster farm in Mobile Bay. The proposed system includes two primary components: lightweight, modular oyster cages and a dual-winch reeling device for automated retrieval. Three cage prototypes—rectangular, oval, and hexagonal—were evaluated for structural performance and fabrication feasibility. The oval design was ultimately excluded due to practical fabrication limitations. The rectangular and hexagonal designs were fabricated using recycled materials and tested under the most extreme environmental conditions derived from years …

Assessing The Fate Of Antibiotic Resistance Genes In Wastewater Treatment Processes, Gunter A. Campbell

Civil Engineering Undergraduate Honors Theses

The increasing need for clean water has paved the way for the creation of systems for reusing water, such as wastewater treatment plants (“WWTPs”), to provide potable water. But in recent years, such systems have raised concerns about the distribution of antibiotic resistance genes (“ARGs”). Bacteria are adapting to antibiotics by the evolution of resistance mechanisms, such as high mutation rates and horizontal transfer. The presence of ARGs, particularly tetracycline ("tetA") resistance genes, in wastewater effluents is of concern, as they can survive treatment, spread to bodies of water, and pose a threat to human health. In this study, the …

Bim Assessment For State Departments Of Transportation, Francisco Israel Guillen

Open Access Theses & Dissertations

Building Information Modeling (BIM) has been used by the Architecture, Engineering, and Construction (AEC) industry to enhance the efficiency and quality of work across various stages, including planning, design, construction, and operation and maintenance (OM) of projects. Despite widespread adoption in vertical construction, BIM implementation in infrastructure projects is still falling behind. This disparity can be attributed to several factors, including the complexity and scale of infrastructure projects and varying levels of BIM adoption and integration within organizations. Efforts to standardize BIM practices and enhance the digital capabilities of infrastructure projects are essential to bridge this gap and ensure the …

Charging Infrastructure Needs For Electric Trucks In Texas, Katerina Jilkova

Open Access Theses & Dissertations

This thesis focuses on the design of a methodology for determining the optimal location of charging stations for heavy-duty electric trucks. The work focuses primarily on long-distance trips that require charging the truck battery outside cities, where the range of charging stations is not extensive. In addition to design the algorithm, the thesis also focuses on implementing the algorithm on a specific case - the implementation of charging stations in the I-10 Freeway corridor between El Paso and San Antonio. The output of the work is not only a description of the procedure, but also an application to a real …

Wind-Induced Gravel Blow-Off: Experimental Investigations And Predictive Modeling For Resilient Roof Design, Md Safwan Ahsanullah

All Dissertations

Roof gravel blow-off during severe windstorms is a major hazard, leading to roof damage and significant downwind impacts. Understanding the initiation mechanisms for gravel blow-off is critical for improving building design and mitigating windborne debris risks. Existing experimental data on the wind speed required to initiate gravel blow-off have been collected from high-speed, full-scale tests at wind tunnels. While these tests form the basis of current design guidelines, they are expensive and can lack generalizability. As a result, rooftop gravel is frequently blown off at wind speeds below the design thresholds. This dissertation investigates the onset of rooftop gravel motion, …

Feasibility Of Liquid Carbon Sources For Algae Growth, Brady S. Jones

Chemical Engineering Undergraduate Honors Theses

This thesis explores the use of electrochemically produced aqueous bicarbonate as a novel liquid-phase carbon source for enhancing algal biomass productivity. Targeting the freshwater microalgae Chlorella Saccharophila, the study investigates its growth response to varying bicarbonate concentrations and compares the efficacy of liquid bicarbonate delivery with traditional gaseous CO₂ bubbling methods. Results demonstrate that Chlorella Saccharophila can sustain growth solely on bicarbonate, and that bicarbonate-fed cultures yielded higher biomass than those supplied with gaseous CO₂ or hybrid systems. These findings validate the potential of bicarbonate-based carbon delivery for scalable algae cultivation, offering key advantages such as gas-free operation, improved …

Analysis Of Hydrological Model Uncertainty In The Response Of Farmers' Decision Models: A Case Study From The Lower Mississippi River Basin Region, Aayush Khadka

LSU New Orleans Theses and Dissertations

Ever since human have evolved on planet earth, they have been dependent on water resources for almost every aspect of their lives. From food production to industry, water has been an integral part of the ever-growing human civilization. Increasing reliance on water has resulted in development of effective and sustainable management strategies. However, water management has remained a complex task due to different human and natural stressors. Hydro-economic models are powerful tools that have been widely used to study water resource systems, management options, economic values, and infrastructures. They have been used to analyze the Water-Energy-Food nexus, climatic interactions, and …

Effects Of Mississippi River Borrow Area Design On Riverine Sediment Transport Using Delft 3d, Kiara B. Horton

LSU New Orleans Theses and Dissertations

This research uses a Delft3D model to investigate the impacts of Mississippi River borrow areas on the Mississippi River navigation channel. The largest navigation concerns for the Mississippi River are operation and maintenance costs down; this includes costs of transportation and dredging. Borrow areas are created to supplement beneficial use of dredge material in various projects. Borrow areas are designed to a standard set of guidelines, according to Coastal Protection and Restoration authority (CPRA), and consider impacts to the navigation channel by requiring and minimum distance from the navigation channel. This study models the total sediment transport and amount of …

Ai-Powered Inspection: A Computer Vision System For Efficient Defects Detection In Underground Infrastructures, Rasha Alshawi

LSU New Orleans Theses and Dissertations

Undetected defects in culverts and sewer pipes pose significant risks to public safety, leading to infrastructure collapses, flooding, and transportation disruptions. Traditional manual inspections are time-consuming, costly, and prone to human error, while existing automated methods struggle with occlusions, irregular defect shapes, class imbalances, and high computational demands. To address these challenges, this dissertation develops advanced semantic segmentation systems that automate defect detection, significantly improving efficiency and accuracy.

This research introduces a series of innovative models designed to overcome these challenges in underground infrastructure inspection. Using dual-attentive mechanisms, sparsely connected blocks, and depth-separable convolutions, these models improve segmentation performance and …

Drainage Area Limitations Of Single Watershed, Peak Flow Estimates From Nrcs Methods, Timothy A. Maughan, Rollin H. Hotchkiss, Riley Hales

Nebraska Department of Transportation: Research Reports

Most state Department of Transportation roadway design sections predict peak flow for culvert design using, amongst other approaches, Natural Resources Conservation Service (NRCS) TR-20 technology. Even though this technology is more than 50 years old, there are no clear guidelines for how large a single watershed drainage area may be while remaining appropriate for predicting peak discharge with this method. Our objective was to identify the drainage area where TR-20 peak flow predictions significantly deviate from flow frequency predictions. We developed flow frequency estimates for 130 small-area stream gage sites in rural Nebraska and compared the calculated return period discharges …