Engineering Commons^™

The Effects Of Pedestrian Countdown Timers On Safety And Efficiency Of Operations At Signalized Intersections, Jacob N. Schmitz

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Pedestrian countdown timers are becoming common at urban and suburban intersections. The added information that pedestrian countdown timers provide to pedestrians can also be used by approaching drivers. A before and after case study on the effects that pedestrian countdown timers have on safety and efficiency of operations was performed at two signalized intersections in Lincoln, Nebraska. The effects on both drivers and pedestrians were analyzed. Performance measures for pedestrian analysis include pedestrian compliance and average pedestrian walking speed. Performance measures for the driver analysis include probability of stopping and speed at the stop bar of vehicles during the yellow …

Identification Of Risk Factors Associated With Motorcycle-Related Fatalities In Ohio, Deogratias Eustace, Vamsi Krishna Indupuru, Peter W. Hovey

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Out of the 7,138,476 motorcycles operating on U.S. roads, 346,925 were registered in the state of Ohio in the year 2007. Although motorcycles represent only 2.8% of all registered vehicles in the state of Ohio, motorcycling accounts for more than 13% of Ohio highway traffic fatalities. Since 2005, Ohio has had a distressing distinction of being among the fifteen states that have sustained more than half of all motorcycle fatalities recorded in the USA (NHTSA 2007; NHTSA 2008a). For the past ten years, the overall motorcycle crash fatalities have been increasing while the motor vehicle occupant crash fatalities have been …

Identifying Changes In Climatic Trends And The Fingerprints Of Landuse And Landcover Changes In The High Plains Of The Usa, Denis Mutiibwa

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Human activities such as conversion of natural ecosystem to croplands and urban-centers, deforestation and afforestation impact biophysical properties of land surface such as albedo, energy balance, and surface roughness. Alterations in these properties affect the heat and moisture exchanges between the land surface and atmospheric boundary layer. The objectives of this research were; (i) to quantitatively identify the High plains’ regional climate change in temperatures over the period 1895 to 2006, (ii) detect the signatures of anthropogenic forcing of LULC changes on the regional climate change of the High Plains, and (iii) examine the trends in evolving regional latent heat …

Development Of Guidelines For The Rating, Inspection, And Acquisition Of Railroad Flatcars For Use As Highway Bridges On Low-Volume Roads, Jason T. Provines, Robert Connor

Indiana Local Technical Assistance Program (LTAP) Technical Reports

Due to budget constraints, many state and county highway agencies are often forced to develop innovative and economical rehabilitation strategies for deteriorated bridges. One such option is to use a retired railroad flatcar for a bridge superstructure. Railroad flatcars can be found in many lengths, making them versatile options for replacing bridges of a range of span lengths up to about 90 feet. Railroad flatcars are also completely modular and lightweight, allowing for quick construction. Within Indiana, as well as other states, several of these bridge structures have been in service for many years.

Although their performance has been satisfactory, …

Estimating Highway Maintenance Work, Fifth Edition, Ohio Department Of Transportation, Indiana Ltap

Indiana Local Technical Assistance Program (LTAP) Publications

This manual is founded upon a problem index that walks through a number of equations that will estimate the maintenance work required in areas such as bridge deck repair, chip and seal, crack sealing, mowing, road salt application, salt spreader calibration, and many more everyday road maintenance operations. The manual also includes an appendix to help with lengths, areas, volumes, rates, equivalents, and rules.

Bs News July/August

Building Services Engineering

No abstract provided.

An Enzymatic Treatment Of Soil-Bound Prions Effectively Inhibits Replication, Samuel Saunders, Jason C. Bartz, Kurt C. Vercauteren, Shannon L. Bartelt-Hunt

Department of Civil and Environmental Engineering: Faculty Publications

Chronic wasting disease (CWD) and scrapie can be transmitted through indirect environmental routes, possibly via soil, and a practical decontamination strategy for prion-contaminated soil is currently unavailable. In the laboratory, an enzymatic treatment under environmentally relevant conditions (22°C, pH 7.4) can degrade soil-bound PrPSc below the limits of Western blot detection. We developed and used a quantitative serial protein misfolding cyclic amplification (PMCA) protocol to characterize the amplification efficiency of treated soil samples relative to controls of known infectious titer. Our results suggest large (104- to >106-fold) decreases in soil-bound prion infectivity following enzyme treatment, demonstrating that a mild enzymatic …

Flexural Behavior Of Interlocking Compressed Earth Block Shear Walls Subjected To In-Plane Loading, Bradley James Stirling

Master's Theses

This thesis investigates the flexural behavior of interlocking compressed earth block (ICEB) shear walls. In-plane cyclic tests were conducted to evaluate the performance of three flexure dominant large scale ICEB specimens: a slim wall with a 2:1 height to width aspect ratio, a flanged wall, and a wall with an opening at the center. Following the experimental investigation, two types of analyses were conducted for calculating the ultimate strength of flexure dominant ICEB walls: a nonlinear static analysis model assuming lumped plasticity and a plastic analysis model. In addition, incremental dynamic analysis was conducted to address the seismic performance of …

Using Laser Scanning Cytometry To Investigate The Transport Of Nano-Scale Particles In Porous Media, Ryan May

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The increased production of nanomaterials in recent years has been unprecedented. Given their potential toxicity, understanding the mechanisms controlling the transport of nanoparticles in the subsurface is important. In this study, a technique was developed for using a Laser Scanning Cytometer (LSC) to visualize and quantify the stable attachment of nano-scale particles. Experiments using three different size particles, 510 nm, 210 nm and 57 nm, in conjunction with a flow cell system containing saturated glass beads under varied injection duration, solution chemistry, Darcy velocity and solids content were performed. A technique for using the LSC data to develop spatial distributions …

Effect Of Information On Driver's Risk At The Onset Of Yellow, Nathaniel P. Burnett

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Intersection crashes average approximately 8,500 fatal and 900,000 injury accidents a year (1). At the onset of yellow at a high speed signalized intersection, a driver may encounter a region of the intersection approach, where they can neither stop safely nor be able to clear the intersection before the red indication. A wrong decision to stop when it would have been safer to proceed can lead to a severe rear-end collision. Conversely, a wrong decision to proceed through the intersection could lead to the driver running the red light and possibly causing a right angle collision. The traditional …

Computational Microstructure Modeling Of Asphalt Mixtures Subjected To Rate-Dependent Fracture, Francisco Aragao

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Computational microstructure models have been actively pursued by the pavement mechanics community as a promising and advantageous alternative to limited analytical and semi-empirical modeling approaches. The primary goal of this research is to develop a computational microstructure modeling framework that will eventually allow researchers and practitioners of the pavement mechanics community to evaluate the effects of constituents and mix design characteristics (some of the key factors directly affecting the quality of the pavement structures) on the mechanical responses of asphalt mixtures. To that end, the mixtures are modeled as heterogeneous materials with inelastic mechanical behavior. To account for the complex …

Evaluation Of The In-Service Safety Performance Of Safety-Shape And Vertical Concrete Barriers, Francisco Daniel Albuquerque

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Roadside concrete barriers have been widely used to protect errant motorists from hitting roadside hazards or obstacles. Two concrete barrier profiles, vertical and safety-shape, have been used for this purpose. The safety-shape profile has been shown to produce excessive vehicle climbing which tends to increase rollover propensity. The vertical profile, on the other hand, does not cause vehicle climbing, but it does produce higher lateral forces which may produce higher injury levels.

The objective of this research is to investigate which barrier profile is the safest based on real-world vehicle crash data. The safest barrier profile is defined as the …

Delayed Composite Action Coupled With Post-Tensioning For Cast In Place Bridge Deck Systems, Nathanael J. Toenies

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Cast-in-place bridge decks are known to have transverse cracking early in the life of the bridge due to shrinkage and temperature effects. The cracks result from immediate composite behavior between the girder and the deck. For steel bridges, this bond is caused by shear studs welded to the steel beams and embedded in the cast-in-place deck. Prevention or closure of these cracks could greatly increase the durability of the bridge.

The following research focuses on introducing a system that will have delayed composite action, allowing strain in the concrete before it becomes composite with the girder. The system is meant …

Steel Angle Section Members Under Combined Axial Load And Unsymmetric Bending, Maheshchandra Rajasekharan Phanibhushan

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome of an investigation into the experimental and theoretical behavior of steel angle section members under combined axial load and unsymmetric bending. Tests are conducted on a series of six angle section members provided with biaxial pinned-end boundaries about the cross-sectional non-principal axes. The end bending moments and axial load are applied in a quasi-static manner until the member load-carrying capacity is reached. The experimental load-deflection and load-strain curves are recorded. The theoretical analysis is based on a system of both elastic as well as materially nonlinear differential equations. The equations were solved using an iterative …

Probabilistic Assessment Of Drought Characteristics Using A Hidden Markov Model, Ganeshchandra Mallya, Shivam Tripathi, Sergey Kirshner, Rao S. Govindaraju

2011 Symposium on Data-Driven Approaches to Droughts

Droughts are evaluated using drought indices that measure the departure of meteorological and hydrological variables such as precipitation and stream flow from their long-term averages. While there are many drought indices proposed in the literature, most of them use pre-defined thresholds for identifying drought classes ignoring the inherent uncertainties in characterizing droughts. In this study, a hidden Markov model (HMM) [1] is developed for probabilistic classification of drought states. The HMM captures space and time dependence in the data. The proposed model is applied to assess drought characteristics in Indiana using monthly precipitation and stream flow data. The comparison of …

Assessment Of Statewide Intersection Safety Performance, Christopher M. Monsere, Todd Johnson, Karen Dixon, Jianfei Zheng, Ida Schalkwyk

TREC Final Reports

This report summarizes the results of an analysis of the safety performance of Oregon’s intersections. Following a pilot study, a database of 500 intersections randomly sampled from around the state of Oregon in both urban and rural environments was assembled. These intersections were categorized into eight types based on number of legs (3 and 4), land use (urban or rural) and traffic control (signalized or minor stop-control). These categories were chosen to align with the intersection types in AASHTO’s recently released Highway Safety Manual (HSM). Geometric and traffic control elements were supplemented by compiling crash data and volumes on the …

Piedras Blancas Light Station Vista Point Improvement Plan, Larissa Heeren, Reuben Juster, Annamarie Usher, John Rossi, Nick Mitchell

Mechanical Engineering

Piedras Blancas Light station Improvement Involved the design of two separate parking lot/vista point plans as well as the creation of a concrete Iron Ranger located near the gift shop on site.

Computational Micromechanics Modeling Of Damage-Dependent Bituminous Composites Based On Two-Way Coupled Multiscale Approach, Jamilla Lutif

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

This study presents a multiscale computational model with its verification and validation to mechanical behavior predictions of bituminous composites that are subject to fracture damage. Bituminous composites are classical examples of multi-phase composites in different length scales. The understanding of the mechanical behavior of asphaltic media has been a challenge to the pavement mechanics community due to multiple complexities involved: heterogeneity, anisotropy, nonlinear inelasticity, and damage growth in multiple forms. To account for this problem in an accurate and efficient way, this study proposes the use of the two-way coupled multiscale computational modeling technique.

The two-way coupled multiscale model is …

The Effect Of On-Line Videos On Learner Outcomes In A Mechanics Of Materials Course, Jeffery S. Thomas, Richard H. Hall, Timothy A. Philpot, Douglas R. Carroll

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Mechanics of Materials course is one of the core engineering courses included in the curriculum of mechanical, civil, mining, petroleum, marine, aeronautical, and several other engineering disciplines. As a core course, the Mechanics of Materials course typically has large enrollment. Initiatives aimed at improving the effectiveness of the engineering core courses can have a major impact on engineering education by virtue of the large number of students affected.

Computers afford opportunities for creative instructional activities that are not possible in the traditional lecture-and-textbook class format. The study described in this paper examines the effectiveness of asynchronous online video that …

Elasto-Plastic Lateral Torsional Buckling Of Steel Beams With Perforated Web, Mohammad Iqbal Mohammad Hesham Martini

Theses

I-shaped steel members represent the basic structural element in the majority of steel structures. Perforated-web I-shaped steel sections have been used as structural members since the Second World War in an attempt to enhance the flexural behavior of traditional solid-webbed I-shaped steel sections without increasing the cost of the material. In general, two types of web perforations are commonly used in engineering practice; hexagonal and circular. Although, the main intent of the perforation process is to produce stiffer I-sections by increasing the web height and providing higher major-axis flexural capacity than solid-webbed members of the same weight, it also provides …

Low Cycle Fatigue Behavior Of Concrete With Recycled Concrete Aggregates, Paul Mark Gordon

Master's Theses

A comparison of concrete containing recycled concrete coarse aggregates and natural coarse aggregates subjected to high strain, low cycle compressive fatigue is presented. Using a strain based feedback control loop, concrete cylinders are compressed at 15µε/s to a specified strain then unloaded to zero stress for 10 cycles. After cycling, all samples are loaded to a strain of 0.008. Direct concrete material variables are the water to cement (w/c) ratio, taken as 0.60, 0.45, and 0.39, and percent coarse recycled concrete aggregate content, varied from zero to 100 percent. The primary testing variable is the specified unloading strain. Unloading strains …

Evaporation From Soils Under Thermal Boundary Conditions: Experimental And Modeling Investigation To Compare Equilibrium- And Nonequilibrium-Based Approaches, Kathleen M. Smits, Abdullah Cihan, Toshihiro Sakaki, Tissa H. Illangasekare

Civil Engineering Faculty Publications - Archive

In the shallow subsurface immediately below the land-atmosphere interface, it is widely recognized that the movement of water vapor is closely coupled to thermal processes. However, their mutual interactions are rarely considered in most soil water modeling efforts or in practical applications where it becomes necessary to understand the spatial and temporal distribution of soil moisture. The validation of numerical models that are designed to capture these processes is difficult due to the scarcity of field or laboratory data with accurately known hydraulic and thermal parameters of soils, limiting the testing and refinement of heat and water transfer theories. The …

Effects Of Coupling In Understanding The Surface Energy Balance In The Snake River Basin, Idaho, Thilinl Jaksa, Kevin Nuss, Venkataramana Sridhar

Civil Engineering Faculty Publications and Presentations

An accurate estimation of surface fluxes and evapotranspiration is critical in understanding the hydrological and meteorological processes linking the land and the atmosphere. Due to difficulties in obtaining extensive and timely field measurements, land surface and atmospheric models are widely employed in estimating such fluxes. This study focuses on testing the ability of Noah LSM to simulate the surface fluxes both in an uncoupled mode and coupled within an atmospheric model. An agricultural area in the Snake River Basin in Idaho and its surrounding natural vegetation regions are the study area. Two model improvements are tested in this investigation: modification …

The Adaptability And Sustainability Of Surface Water Diversions Along The Main Stem Of The Snake River In Southern Idaho, David J. Hoekema, Venkataramana Sridhar, Xin Jin

Civil Engineering Faculty Publications and Presentations

Agriculture in southern Idaho depends heavily on the conversion of snowpack into spring runoff. The Natural Resource Conservation Service (NRCS) has developed a Surface Water Supply Index (SWSI) as a tool to predict whether or not forecasted runoff and reservoir storage will be adequate to meet irrigator’s needs at a basin scale. This research by comparing SWSI to diversions for individual canals advances the use of SWSI to develop a Surface Water Supply Metric (SWSM) that can be used to estimate the reliability and sustainability of diversions under historic and projected time periods. An historic analysis of diversions during three …

Rate-Dependent Behavior Of Clay, Harry F. Martindale Iv

Master's Theses

This thesis presents a strain-rate dependent two-surface plasticity constitutive model for clays based on the critical-state soil mechanics.  The model reproduces the mechanical response of clays under multi-axial loading conditions and predicts both drained and undrained behaviors at small and large strains.  Model parameter values are determined for Boston Blue Clay, London Clay and Kaolin Clay.  The performance of the model in simulating the mechanical response of clays is demonstrated for a variety of strain rates. Sensitivity of each model parameter is checked for ±5, ±10 and ±20% of the deterministic values. Probabilistic analysis using Monte Carlo simulations were done …

The Impacts Of Road Capacity Removal, Jason E. Billings

Master's Theses

The road infrastructure of North America is aging, and many governments are faced with a critical decision:  do we repair or remove freeways from our urban centers?  Freeway repair is exceptionally expensive, but removing a freeway is widely seen as a risky venture which may result in negative traffic effects.  Therefore, it is necessary to gain a clearer understanding of how removing road capacity effects traffic distribution.  Three freeway segments were ultimately selected for case study analysis: two in San Francisco and one in Milwaukee.  This analysis consisted of identifying changes in the traffic volumes and volume-capacity (V/C) ratios in …

Wired For Business: The Roebling Story., Kelley Marie Hatch-Draper

Electronic Theses and Dissertations

John Augustus Roebling, a classically educated civil engineer and young Hegelian, immigrated to America in 1831 in search of freedom from a repressive political system that afforded him no opportunity for advancement. Arriving in the midst of the American market revolution, his dream of establishing an agrarian farming colony changed in response to societal transformations resulting from mechanization and the rise of industry. Within forty years, Roebling achieved fame as a canal engineer and bridge designer while establishing the American wire rope industry. Without Roebling's innovation in wire-rope, modern suspension bridges, high-rise elevators, construction cranes, and cable cars would not …

Comparative Field Performance Study Of Flat Plate And Heat Pipe Evacuated Tube Collectors (Etcs) For Domestic Water Heating Systems In A Temperate Climate, Lacour Ayompe, Aidan Duffy, Sarah Mccormack, Michael Conlon, Mick Mckeever

Articles

This paper presents a year round energy performance monitoring results of two solar water heaters with 4 m² flat plate and 3 m² heat pipe evacuated tube collectors (ETCs) operating under the same weather conditions in Dublin, Ireland. The energy performance of the two systems was compared on daily, monthly and yearly basis. Results obtained showed that for an annual total in-plane solar insolation of 1,087 kWh/m², a total of 1,984 kWh and 2,056 kWh of heat energy were collected by the 4 m² FPC and 3 m² ETC systems respectively. Over the year, …

Investigation Of Concrete Sealer Products To Extend Concrete Pavement Life, Justin Nielsen

Boise State University Theses and Dissertations

Portland cement concrete pavements (PCCP) are susceptible to deterioration and decreased service life caused by the ingress of water. Water can dissolve and transport deleterious chemicals such as de-icing salts, carbon dioxide, dissolved oxygen, and sulfates into PCCPs through cracks and the concrete surface. These chemicals and water itself all have the potential to degrade PCCP by chemical and/or physical processes. Surface-applied concrete sealers have demonstrated the ability to increase service life of PCCPs by limiting the ingress of water and deleterious chemicals into concrete.

Concrete sealers are being increasingly used by the Idaho Transportation Department (ITD). However, little has …

Investigation Of The Use Of Multi-Criteria Decision-Making Tools For Management Of An Urbanizing Watershed, Reed C. Colton

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The regulation of non-point pollution sources (e.g. agricultural runoff and stormwater discharges) as mandated by the 1972 Clean Water Act, forced a fundamental paradigm shift from “end of the pipe” pollution control to a watershed management approach. Multiple jurisdictions and often conflicting objectives make it difficult to reach stakeholder consensus and execute watershed management decisions. To facilitate decision making when multiple and/or conflicting objectives exist, Multi-Criteria Decision-Making (MCDM) tools were developed for diverse applications, and potentially could be used to facilitate watershed management.

The overall objective of this thesis was to evaluate MCDM tool use to facilitate community-based management of …