Digital Commons Network^™

Reduction Of Acoustic Feedback Oscillations By Use Of Spectrum Shifting, Youssef Abdelilah

Theses

The problem of whistling noise or self-oscillation in public address systems operating in closed halls or rooms can be very disturbing to the listeners. This noise is sustained when the positive acoustic feedback, of the public address-room system, meets the oscillation criteria. This feedback system results from the acoustic sound signal reflected off the room walls and any other obstacles in the room, originating from the public address speakers and then re-entering the microphone.

When all of the audio signal components entering the public address system are shifted by a frequency increment Δf of 6 Hz, an increase of 5 …

Pressure Swing Absorption-Based Separation Of A Gas Mixture, Syamalendu Bhaumik

Theses

In this study, separation of a gas mixture was investigated using the novel concept of pressure swing absorption in a stationary absorbent liquid. The best features of pressure swing adsorption, gas liquid scrubbing and hollow fiber based membrane processes were incorporated to develop the process.

A well-packed microporous hydrophobic hollow fiber module was used to achieve absorption of a gas at a high pressure into a liquid during a certain part of the cycle followed by desorption of the gas from the liquid in the other part of the cycle. The device has a very high interfacial area per unit …

A Successive Approximation Algorithm To Solve Motion Planning Problems, Cheng-Ming Chang

Theses

A successive approximation algorithm is presented to solve motion planning problems and optimal control problems. A motion planning problem is included in an optimal control problem and due to the heavily nonlinear and coulped differential equations describing the dynamics of the manipulator and several constraints imposed on the system, few efficient methods exist to solve this kind of problems.

The successive approximation algorithm can decompose the global nonlinear problem into several nonlinear subproblems and each subproblem is solved by the nonlinear programming method with a highly convergent rate. Because the limited constraints and variables are included in each subproblem and …

Studies Of Wet Thermal Oxidation Of Silicon And Porous Silicon, Nilesh A. Gharia

Theses

Wet Thermal Oxidation of Silicon in VLSI is an extremely important step in the formation of field oxides. Understanding oxidation kinetics is critical for process reproducibility. The present study aims at gaining an insight into the oxidation kinetics through large experimental data at process temperatures of 800°C, 900°C, 1000°C and 1100°C with a bubbler temperature of 98°C. Oxides with thicknesses ranging from 100A to 7000A have been grown. Rate constants are obtained for the growth kinetics. Extensive characterization studies have been performed on MOS structures produced after wet oxidation.

In addition, porous silicon which assumes a growing significance in the …

Partial Vlsi Implementation Of The Architecture For Reusable Components (Arc), Deepak Kakadasam

Theses

This work describes a novel VLSI implementation of the Architecture for Reusable Components (ARC) processor, using Hardware Description Language (HDL). The main goal here is to achieve efficient execution of reusable software through proper hardware support. This involves the hard wired implementation of each instruction designed for the ARC processor.

Instructions are broken down into their logical functions, then modeled and simulated through the hierarchical design methods that HDL offers. The structural model of the processor has been developed and simulated. The purpose here has been to begin work on the design and implementation of the ARC processor.

The instructions …

A Review Of Energy Storing Prosthetic Feet And Computer Aided Structural Optimization Of A Below-Knee Prosthesis, Poonam Gope Lalwani

Theses

Because people with physical disabilities have shown an interest in participation in sports, a new class of prosthetic feet known as "energy storing prosthetic feet" has been developed. These new developments in prosthetic foot design utilize energy storage and return to improve ambulation. This thesis reviews the design, materials, advantages and disadvantages of various energy storing prosthetic feet. Research studies, comparing gait in below-knee amputees using different prosthetic designs, can be applied to the design of prosthetic feet that are lighter, stronger and more reliable. Comparisions among these feet are reviewed in the context of functional capability and patient satisfaction. …

Modification Of Wear Testing Machine And Study Of Wear Resistance, Ning Li

Theses

In this work a modification of a wear testing machine has been done by designing a new loading mechanism and redesigning different components for a new roller-on-roller wear testing machine. A new loading mechanism containing gearbox frame and load cell assembly have been designed, manufactured and assembled. A pusher of the pushing mechanism is redesigned for better durability. Existing bearing support was redesigned and replaced. All new units of the wear testing machine were lined up and assembled with the machine. Finite element stress analysis for designed frame in the load mechanism was performed by using the Integrate Design Engineering …

Microstructural Investigation Of Surface Coating Developed By Electro-Spark Deposition Technology, Tianzong Xu

Theses

Electro-spark deposition (ESD) is a pulsed-spark micro-welding process using an electrode to apply a fused, metallurgically bonded coating with an extremely low heat input so as to eliminate thermal distortion or changes in metallurgical structure of the substrate. The deposited surface achieves an exceptionally fine-grained, homogeneous coating that may approach as amorphous structure which is believed to contribute to good wear and corrosion resistance.

In this research, an optical image analysis system, scanning electron microscope with computerized energy dispersive spectrometer, microhardness testing system and computerized surfanalyzer were employed to investigate the microstructure and properties of achieved surface coatings.

As the …

The Thermal Model Of The Rat Under Hemorrhagic Shock Hypothermia With Microwave Intervention, Liu Zhe

Theses

A whole body thermal model simulating heat distribution and temperature regulation in rats during hemorrhagic shock and during post-shock microwave core rewarming period was developed. An electrical circuit was used to simulate the thermal system and a software named PSpice? was used to analyze the circuit. The temperature regulation as the result of the simulation is demonstrated to match the measured temperature histories of rats in hemorrhagic shock and the microwave rewarming experiment.

The blood pressure drop and cardiac output decrease were considered in the simulation and the so called "set point temperature" was investigated in the model. Linear decrease …

A Petri Net Toolkit For Parallel Program Debugging, Potla Kishore Reddy

Theses

An effective debugger must support the language and operating system resource abstractions that are available to the programmer. Earlier debuggers worked at the machine architecture level: they dealt with machine instructions and registers. Current debuggers, designed for single process debugging, permit access to program variables and breakpoints and single-stepping at the level of high-level language statements. Eventhough the current debuggers, are already implemented to be a powerful tool, they still cannot do a job of parallel debugger.

In this thesis, a computer simulation system has been established by Petri Nets execution providing a convenient and friendly interface as it allows …

Networking High-End Cad Systems Based On Pc/Ms-Dos Platforms, Dagmar Antje Brinkmann

Theses

The concept of today's technology has been dropped. Everything is now either oobsolete or experimental. Yesterday's technology is appealing only because it is tried-and-true and prices are reduced for clearance. Tomorrow's technology is exciting, somewhat expensive and not well tested.

In the field of architecture, where most firms are medium or small, having limited resources, the high cost initially required for a CAD installation was generally impossible to meet not too many years ago.

From spreadsheets and CAD graphics to network file systems and distributed database management, the basic systems and application tools have matured to the point that the …

A Thermal Desorption Modulator For Continuous Monitoring Of Volatile Organic Compounds, Yun Chen

Theses

A thermal desorption modulator is made from a short segment of thin tubing containing an adsorbent or a chromatographic stationary phase. A carrier gas containing the analyte is introduced into the analytical column through the modulator which acts as a sample trap. Rapid electrical heating of the modulator releases a "concentration pulse" of the analyte and this serves as an injection similar to that from an injection valve. The modulator also acts as a sample preconcentrator and can be used to make repetitive injections every few seconds. In this research, the mechanism of thermal desorption modulator was studied and was …

Trouble Shooting In Plastic Injection Molding Machines, Zafar Kamal

Theses

The purpose of this thesis is to find the solution of those problems which occur during plastic injection molding process. Molding cycle problem analysis is an important field in plastic injection process. It is very necessary to catch the problems during operation. Therefore on the basis of research trouble shooting criteria is prepared.

Good quality control is an essential feature for finding any sort of fault. Quality control is associated with each and every step of operation to maintain the required shape and surface finishing.

Most of the molding problems are solved by varying the machine conditions and by changing …

Application Of Organophilic Clay, Koshy Koshy

Theses

The overall goal of this project is to asses the feasibility of using clay to filter water contaminated with organic contaminants. The clays that were used were provided by the Union Carbide Corporation and the Industrial Mineral Ventures (IMV), a division of Floridin company. The organic contaminants that this project concentrated on were, naphthalene, 1,4-dioxane, and phenol. The feasibility studies were done by batch isotherm studies. The protocol for the batch studies were the same as the ones used previously for granular activated carbon. This project looked at a total of six Union Carbide clays and five IMV Floridin clays. …

Simulation Study For The Effect Of Dependencies In Queueing Systems, Yitao Bai

Theses

Few theoretical results have been obtained in the literature for the effects of dependencies between random variables on the performance of queueing systems. This thesis aims at investigating this issue via simulation. Several dependencies are studied in detail, including dependencies between interarrival times, between interarrival time and service time, between service times and dependencies between different stages in networks of queues. We define several classes of dependent random variables and study their correlation coefficients, then we apply them to single and multiple station service systems. Comparisons with the independent case, for which the explicit form solution are available, are made …

Timed Petri Net Simulation Of Flexible Manufacturing Systems, Yan Chen

Theses

Standard Petri nets have been used to model and analyze Flexible Manufacturing Systems. The timed Petri net, which can incorporate the time delay associated with manufacturing events, provides additional information about real time behavior of practical systems. The Timed Petri Net Simulation Tool, a highly interactive graphical tool, is applied to simulate the modeled flexible manufacturing systems. Timed Petri net models are experimented with. Machine utilization data and throughput are obtained. Analysis of the results shows that the system performance can be optimized by choosing proper parameters.

Three Dimensional Magnetic Field Sensors And Array In Bicmos Technology, Bingda Wang

Theses

This thesis presents new designs of three dimensional magnetic field sensors in BiCMOS technology. The detailed design of the merged structure device by common diffusion and the high gain transduction circuit are presented. The merged structure has the advantage of less area, less external contacts and less parasitic capacitance. Cross-sensitivity is also eliminated by employing the merged structure. Three active on-chip loads are introduced to improve the sensitivity. The SPICE simulation results show that when a relative change in current ΔI/I is 0.001, about 13.6 mV and 8.5mV can be detected at the output in X(or Y) and Z directions, …

A Comparison Of Integration Architectures, Amar Mahidadia

Theses

This paper presents GenSIF, a Generic Systems Integration Framework. GenSIF features a pre-planned development process on a domain-wide basis and facilitates system integration and project coordination for very large, complex and distributed systems. Domain analysis, integration architecture design and infrastructure design are identified as the three main components of GenSIF. In the next step we map Beilcore's OSCA interoperability architecture, ANSA, IBM's SAA and Bull's DCM into GenSIF. Using the GenSIF concepts we compare each of these architectures.

GenSIF serves as a general framework to evaluate and position specific architecture. The OSCA architecture is used to discuss the impact of …

An Enhancement And Improvement Of A Prototype Distributed System Based On Elements Of An Integration Architecture, Kunal R. Shah

Theses

The concepts and results presented in this thesis are related to Integrated System Development. It provides introduction to Generic System Integration Framework (GenSIF). And hence its three principal components, Domain Analysis, Integration Architectures and Enabling Technology. It addresses certain issues of distributed processing relating to systems integration.

The primary objective of this thesis is to develop/improve a prototype by applying concepts and ideas presented in GenSIF, with an example channel based building block integration architecture as an example. This prototype was developed with the objective of studying the effect of system intregration framework in mind while working on an application. …

Optical Flow Determination And Motion Analysis, Qian Wang

Theses

Optical flow, also known as image flow, is of fundamental importance in the processing of image sequences. Various approaches to determine optical flow have been proposed --- others continue to appear. Using several sets of real image sequences, here, the results of three different approaches to the the determination of optical flow are reported, the approaches are the Gradient-based approach, the Correlation-based approach and the Correlation-feedback approach. The comparisons are primarily empirical, and they show that the performance of these different algorithms differs significantly among the different image sequences, indicating that there does not exists one superior algorithm which could …

A Programmable Integrated Power Supply For The Electrostatic-Drive Micromotor, Chao Ye

Theses

A 6-phase bipolarized, high-voltage power supply with rectangular pulse shape has been designed to study the special operational characteristics of various electrostatic-drive micromotors. In particular the design powers the variable-capacitance side-drive micromotor. This power supply provides variable frequency, variable voltage, and variable duty-cycle control. Simulation has been used extensively in the design and design verification.

The bipolarization (dual voltage polarity) of each pair of the phases reduces physical clamping of the rotor to the electrical shield beneath it. Thus, bipolarization of the voltage supplied to the stator nodes reduces charge build-up on the rotor.

The output frequency range varying from …

Fingerprint Pattern Recognition For Medical Uses, Feng You

Theses

The purpose of my research is to provide a method to automatically classify fingerprints into three subgroups: whorl, loop and arch, which can help medical scientists to study the relationship between fingerprint patterns and medical disorders. In the research, two different kinds of approaches were developed. The first one is performing pattern recognition in the frequency domain, which uses the feature of Fourier spectrum. That is, prominent peaks in the spectrum give the principal direction of fingerprint patterns. Using the above feature, we can obtain the principal direction of every subregion, after which the pattern of the whole image can …

A Study Of Pulsation Of Chest Wall Using Microwave Interferometer, Paul Zeno

Theses

The microwave interferometer is utilized to pick up vibrations of the anterior chest wall produced by the cardiac activity. The objective of this project is to find the causes of different peaks in the output of the microwave interferometer. The output of the microwave interferometer is recorded simultaneously with EKG and jugular pressure pulses. Eighteen subjects had their mechanical vibrations of the chest wall, EKG and jugular pressure pulses recorded. The processed interferometer data, when compared with EKG and jugular pressure pulses appear to have a close relation to the mechanical events in the cardiac cycle. Four peaks in the …

Computer Implementation Of Mason's Rule And Software Development Of Stochastic Petri Nets, Xiaoyong Zhao

Theses

A symbolic performance analysis approach for discrete event systems can be formulated based on the integration of Petri nets and Moment Generating Function concepts [1-3]. The key steps in the method include modeling a system with arbitrary stochastic Petri nets (ASPN), generation of state machine Petri nets with transfer functions, derivation of equivalent transfer functions, and symbolic derivation of transfer functions to obtain the performance measures. Since Mason's rule can be used to effectively derive the closed-form transfer function, its computer implementation plays a very important role in automating the above procedure. This thesis develops the computer implementation of Mason's …

Computer Aided Finite Element Stress Analysis Of A Three Dimension Mandibular Bone Model Using I-Deas Software, Yixiong Xu

Theses

A three dimensional model of half of the mandibular bone, with 487 tetrahedra elements and 1,047 nodes, is established and analyzed by means of I-DEAS software. The masseter muscle is assumed to be 15° deviation from y-axis, and the Umetani boundary conditions are allowed to be varied. A 337 lb force was applied along the midline of the mandible to simulate a trauma force caused by the auto accident. The maximum principal stress is 18,400 psi and the minimum principal stress is -1,340 psi. Depending on the experimental results of dispalcement and maximum principal stress, the conclusions are drawn: 1) …

Evaluation Of Truck Restrictions Using Simulation, Shaikh Mohamed Arif

Theses

Traffic congestion is a major problem in many central business districts. Many strategies have been proposed and implemented to solve or alleviate this problem. One of the most common strategies is to impose travel restrictions on the movement of trucks, without reviewing the economic consequences of goods movement restrictions on shippers, customers and on the overall business activity of the area.

This research examines the effect of various truck restrictive policies on the cost of urban goods movement, using the central business district of Manhattan as a case study. Computer simulation techniques are used to evaluate several scenarios under different …

Behavior Of R/C Columns Under Nonproportional Variations In Axial And Lateral Loads, Kaniz Fatema Ahsan

Theses

The study on the behavior of reinforced concrete columns subjected to the motion of earthquake suggests that the structure may experience nonproportional variations in axial and lateral forces. In order to assess the capacity of a reinforced concrete structure under nonproportional loadings, an analytical model is developed using the fiber modeling technique.

The method is based on detailed analytical description of the geometry and material properties used in evaluating the behavior of the critical regions rather than a simplified and predefined set of hysteresis rules. The present study has two principal components of investigation. First, the analyses are done at …

Measures For Estimating The Need For Flexibility In A Manufacturing Facility, Raghu Chilukuri

Theses

Manufacturing technology is in the midst of on-going developments stemming from rapid improvements in machine tools, computers and robots. These developments present engineers with greater challenges and opportunities in designing more complex and productive systems. The concept of flexibility was defined by authors like Jaikumar, Son & Park, and Buzacott. The various challenges can be partly over come by building flexibility into the various systems. Various operational or raw measures are described as they help managers to understand the kind and extent of flexibility embedded in their production process and allow them to make informal judgement on new equipment.

Various …

An Improved Human Gait Model Incorporating The Effects Of Muscle Activity And Joint Friction, Tae Ho Choi

Theses

In designing an artificial leg for an amputee, it is important to find those underlying principles which determine the normal human gait. For this purpose we have developed a model of human walking, in which it is possible to predict an optimal gait at any given speed of walking based on the principle of minimum mechanical energy consumption.

Our model is an extension of the model proposed by Mochon and McMahon (1980). Their model assumes that during the swing phase of walking mechanical energy is conserved. Non-conservative forces due to muscle activity are assumed to occur during the double support …

The Permeability Of Hot Mix Asphalt Concrete With Petroleum Contaminated Soils, Kuen-Yuan Chuang

Theses

It is estimated by the United States Environmental Protection Agency (USEPA) that there are 2 to 3.5 million underground storage tanks (USTs) throughout the nation and about 25% of these tanks are leaking. The leakage of petroleum or other organic material presents serious environmental problem due to the uncontrolled release of petroleum products to ground water. Many new techniques have developed to reuse these petroleum contaminated soils generated from sites containing leaking USTs. One such soil reuse method available since 1985 is the use of petroleum contaminated soils in the production of hot mix asphalt.

The stability, durability, and hydraulic …