Digital Commons Network^™

An Experimental Investigation Of Round Normal Impinging Jet Of Water, Dipendra Saharay

Theses

The various flow parameters of round jets of water impinging normally on a flat plate are measured experimentally. The velocity and pressure distribution along the axis of the jet at various sections of the jet parallel to the horizontal lucite striking plate and along the impinging surface was found. The nozzles used were 1/4 inch and 1/2 inch in diameter. The Reynolds number based on the nozzle diameter was 15,000 to 25,000. The distance from the jet origin to the deflecting boundary ranged from thrice the diameter of the jet to twelve and sixteen times the diameter of the jet. …

Kinetics Of Biodegradation Of Phenol And 2,6-Dichlorophenol, Samir Shrikant Desai

Theses

Biological removal of phenol up to 600 ppm and 2,6-dichlorophenol up to 20 ppm was studied in a well aerated fill-and-draw reactor of 41 capacity at 26 C using an activated sludge obtained from the municipal treatment plant in Livingston, N.J. Experimental evaluation of kinetic parameters showed that biodegradation of both phenol and 2,6-DCP followed zero-order kinetics. As expected, the lag time for both compounds was considerably reduced when acclimated sludge was used. However, the metabolism of 2,6-DCP was very slow even for preacclimated sludge, requiring about 36 hours to degrade only 15 ppm.. This was markedly improved by the …

Preparation And Characterization Of Blocked Isocyanate Monomer Polymer And Equilibrium Constant Of Deblocking, Kirti P. Kamdar

Theses

A 2-Hydroxyethyl methacrylate (HEMA) adduct of toluene 2-4 diisocyanate (TDI) was prepared in petroleum ether at 35-40°C under nitrogen. In order to prepare the monomer, equimolar amounts of TDI and HEMA were reacted with P-cresol which functions as a blocking agent.,Di-butyltin dilaurate was used as a catalyst and chloranil was used as an inhibitor. The solid monomer which was obtained was recrystallized, and polymerized in chloroform using azobis isobutyronitrile as initiator.

Monomer and polymer were characterized using infrared spectroscopy, melting point, liquid chromatography gel permeation chromatography. A vapor pressure osmometric study of the polymer in three different solvents at three …

Optimization Of A New Linear Fm Detector Using Digital Signal Processing Techniques, Edward J.A. Kratt

Dissertations

This dissertation describes and synthesizes a new member of the family of FM detectors introduced earlier by Klapper and Kratt. A salient property of these detectors is low delay with excellent sensitivity. The emphasis in the new detector is on the ease of digital implementation. In addition, the new detector is also extremely linear. In congruence with the other Klapper-Kratt detectors, it makes use of zero group delay elements, balance at RF, quasi-synchronous detection and carrier cancellation. The Performance of the detector is mathematically analyzed under the conditions of a modulated input wave, sinewave [sic] interference, and noise. The results …

The Effect Of Ultrasound On The Hydrolysis Of Carbohydrates, Adel A. Khamis

Dissertations

Acid hydrolysis of dextran and cellulose were studied with and without irradiation with ultrasonic waves of different frequencies (17 - 150 KHz), and powers (0.4 - 200 w/cm²). In the case of both materials, the hydrolysis reaction was found to be first order with respect to the activity of hydrogen ions in the reaction medium. Weight average molecular weight was evaluated at different durations of the reaction course. The reaction rate of dextran was found to be proportional to the weight average molecular weight raised to the power 4/3, and raised to the power 4 for cellulose.

The …

Application Of Fuzzy Theory To Pattern Recognition, David Usechak

Dissertations

Piecewise curve approximation is used to describe boundaries of objects in pictures and waveforms. The method consists of linear and quadratic piecewise polynomial approximations in which the error must not exceed a predetermined cost threshold. A fuzzy Bayes model is used to determine if a breakpoint exists within an interval I_n or between intervals I_n and I_n+1 and to determine whether these intervals can be merged for data compaction reasons. In order to achieve these objectives a new fast algorithm has been proposed which gives good curve/object fitting. This algorithm uses a technique for generating generalized inverse …

Nucleus 1983, New Jersey Institute Of Technology

Yearbooks

This is a digitized, downloadable version of the Newark College of Engineering Nucleus.

Mathematical Modeling Of The Unsteady State Glucose And Insulin Concentrations In Blood For Normal Subjects And Diabetics, Tung Shih

Theses

A mathematical model of the blood-glucose regulatory system has been developed. This model describes an oral glucose tolerance test adequately and simulates the behavior of the real physiological system using computer techniques.

Regression of the rate constants involved have been effected by conforming the theoretical functions to the data from glucose tolerance test in nonobese normal subjects, obese normal subjects, nonobese mild diabetics, obese mild diabetics, nonobese moderate diabetics and obese moderate diabetics measured by continuous sampling after oral ingestion. Most of the data were conformed within the limits of experimental error. The result of optimal parameters lead to a …

Computer Simulation Of Cavity Filling During Injection Molding Process, Sumit Banerjee

Theses

A numerical technique is proposed for the simulation of cavity filling process during injection molding of glass-bead filled polypropylene. The mold cavity is of cylindrical shape. Marker And Cell (MAC) method is utilized for solving the transient flow phenomena, after a mathematical simulation of the flow model is carried out by using the relevant continuity and-momentum equations governing the system. The complexity of the equations involved, results in the simplifying assumption of incompressible and isothermal flow process. A computer program is written on the basis of finite-difference equations developed during the application of MAC method under the prevailing conditions.

The …

An Improvement In The Chemical Engineering Simulation System, Roman Andreyuk

Theses

The accurate design of chemical processing plants is important to the chemical engineer. The original version of CHESS (Chemical Engineering Simulation System) greatly reduced the amount of time which previously had to be spent on the design of such plants by providing the engineer with a package which simulated some of the more common pieces of chemical processing equipment found in a typical chemical plant.

The present version of the Chemical Engineering Simulation System (CHESS2) presents a significant improvement over the original version. The improvement was achieved by expanding the thermodynamic package, offering the user a choice of methods by …

Proposed Product Plan For A High Growth, High Technology Organization, Alan R. Eschbach

Theses

Analyzing and consequently redefining a corporation's product line or mix is an important task facing all manufacturing organizations. While this task is usually addressed in detail as part of an organization's business plan, it can be very disconcerting when an organization realizes that the markets and products that got them to where they are now will not necessarily be the ones that will give them the growth that they would like to realize. Redefining the product line can be even more critical to young, high technology organizations who have never done it before and have found themselves facing the possibility …

Nomographs And Tables For Simplified Thermal Analysis Of Power Piping, Dhanjibhai N. Patel

Theses

This Thesis develops Nomographs and Tables for simplified thermal analysis of " Power Piping." It gives the length of required Thermal Relieve Leg when a set of piping parameters such as, pipe size, pipe material, operating temperature and pipe length are given.

The Nomographs and Tables developed here can be used

1. to determine the primary piping layout, piping route, support location etc. before vigorous conputer analysis is performed.

2. to help the Field Engineer on the plant site to make " on the spot " decisions on pending piping route changes.

Two Nomographs are developed in this Thesis. One …

Computer Simulation Of The Human Hypophysial-Ovarian System, Robert Charles Blencowe

Theses

In order to more adequately simulate the human pituitary-ovarian cycle further refinements were made to the original Bogumil and Feng computer models. This involved the inclusion of equations which mathematically describe the peripheral conversion of prehormones and a subroutine showing the effect of plasma proteins, TeBG, CBG, and albumin on the total concentration of estradiol, progesterone, testosterone, androstenedione, dehydroepiandrosterone and estrone.

Once the models were functioning properly, values for the normal state and for the disease condition, Polycystic Ovary Syndrome (PCO), were obtained. In most cases there exists good agreement between the results reported in the literature and those generated …

An Assessment Of Job Attitudes Held By Hourly Workers At A Food Processing Plant, Charles J. Sheahan

Theses

This study applied Vroom's instrumentality-valence model to an assessment of the overall job attitude of hourly workers at a food processing plant. The specific job factors relating to the formation of overall job attitude are described and the managerial implications of the results are discussed. A short discussion of the relationship of these employees' attitudes to Herzberg's motivation-hygiene theory is also presented.

The results of the study indicate a moderate degree of job satisfaction based on Vroom's model. Additionally, the correlations of specific instrumentality to specific valence give a strong indication that the subjects value rewards they perceive as attainable, …

Computer Simulation Of The Respiratory System, Bruce Diner

Theses

The respiratory system was simulated utilizing a series of three models, each more complex than the previous. The first model simulated the respiratory system as a two compartment model driven by carbon dioxide concentration. The second model, also a two compartment model, simulated periodic breathing while the third model is a three compartment model and simulates acid-base balance disturbances.

In this study, the effects of hyperthyroidism and respiratory center depression on respiration premeasured utilizing the models to obtain data and then compare the results to known physiologic data.

The Operational Utility Of The Walton-Mckersie Attitudinal Structuring Model In Collective Bargaining, Donald Warren

Theses

This work is an heuristic inquiry into behavioral change theory designed for application to labor/management interaction in collective bargaining. The theory itself was postulated by Richard E. Walton and Robert B. McKersie in their book A Behavioral Theory Of Labor Negotiations. The principles of their theory are highly axiomatic and their importance and validity can only be recognized through applied empirical analyses that demonstrate or refute its concept.

The aspect of the theory which is the focal point of this research pertains to the structuring and restructuring of attitudes and attendant relationships resulting from the collective bargaining process. The objective …

The Role Of Electrical Noise In Screening Transformers Prone To Failure, Rajeev D. Shirodkar

Theses

Insulation used as a barrier between the high voltage and low voltage windings of a transformer has sites of in- homogeneities like pinholes, cracks or voids, developed during the manufacturing process. Thus, these minute air pockets are stressed much more than the solid dielectric, on the application of a voltage stress, because the dielectric constant of the solid insulation is many times that of the air dielectric. As a result, excitation or ionization takes place in the air (gases). The amount of excited or ionized molecules is proportional to the volume of the inhomogenei- ties within the insulation.

Therefore, experiments …

Behavior Of Composite Steel-Fibrous Concrete Beams, Avijit Mookerjee

Theses

This research thesis on composite steel-fibrous concrete is based on a series of beam tests conducted in the Structural and Concrete Laboratory of the New Jersey Institute of Technology.

In the first series of tests, two twenty-foot two-span continuous beams were tested. In the first beam, plain reinforced concrete was used in the construction of the composite beam. The second beam had 1.5% by volume of steel fibers in the concrete.

In the second series, four composite T-beams were tested. Two of the beams had 1% of steel fibers by volume. The other two beams were constructed using plain concrete. …

Forecasting Construction Product Demand, Robert Singerline

Theses

This is a synopsis of practical and theoretical methods used in forecasting construction product manufacturers' product demand. The practical methodology was accumulated by the author while working as a consultant for the Dodge Construction Information Division of McGraw-Hill. The objective is to review and update the various methods of forecasting with illustrations of current practices that are being used to forecast building product demand. The resulting work will help management in the planning process.

Prediction Of Heats Of Mixing In Hydrogen-Bonded Solutions Using A Unifac Model, Peter John Stathis

Theses

A model for the correlation and prediction of heats of mixing of hydrogen-bonded mixtures is presented. The model incorporates a UNIFAC term to describe the physical interactions and a chemical term to account for the hydrogen bonding contribution. The model is applied to binary and tertiary mixtures of normal, isomeric, substituted, and multihydroxy alcohols with a variety of solvents. Thirteen interaction parameters are determined. For the temperature range 0 to 100°C typical errors of ±10% are obtained.

Gallium Nitride Film Deposition By Ionized Cluster Beam Epitaxy, Ghulum Bakiri

Theses

An experimental Ionized Cluster Beam System similar in design to the one developed at Kyoto University in Japan was. designed and constructed in the Microelectronics Laboratory at NJIT. This involved making the working drawings, having the parts machined and then assembling the system in a vacuum system together with the necessary variable power supplies, meters, controls, gas inlets, cooling water connections, etc.

Eleven deposition runs were then attempted to grow gallium nitride utilizing the system constructed. In a typical deposition run, gallium was vaporized from a boron nitride crucible at 1000° C and allowed to expand through a 0.5 mm …

Finite Element Analysis Of The Femoral Head, Ghandikota Ramamurthy

Theses

Femoral component loosening and Prosthetic stem fractures have renewed interest in conservative alternatives to conventional total hip replacements. One such alternative is the concept of surface replacement. The objective in this study is a finite element analysis of a femoral surface replacement cup with Particular attention given to the interfacial stresses. An axisymmetric model with a grid of two-dimensional isoparametric elements is generated. This study utilizes an adaptive model so as to include the effect of bone remodeling in response to stress. The stiffness is considered to be linearly proportional to the stress in the femoral head and neck. Isotropic …

Mathematical Modeling Of Mass Transfer In A Hollow Fiber Dialyzer, Tzyy-Kai Yu

Theses

A mathematical model describing the flow characteristics and mass transfer has been developed for the hollow fiber dialyzer in countercurrent dialysis.

The theoretical expressions are developed from a typical Graetz problem for the stream side, and a first order differential equation for the dialyzate side. The solution of the dimensionless concentration profile is obtained as a summation of orthogonal eigenfunctions in closed form, which are given as product of an exponential function and a confluent hypergeometric function.

The analytical solution of the model has been examined by adjusting system parameters, like Sherwood number, Peclet number and the geometry of the …

Automation Considerations For A Manufacturing System, Marvin Fachuan Wang

Theses

This thesis examines the present manufacturing system of Apollo Valve Company, a solenoid control valves manufacturing. After analyzing the present system, the automation considerations and proposed new system were recommended.

Chapter 1 presenti the background material of automation and manufacturing system. The development of the automated factory is also included. The plant layout, organization, and departments functions of the present system are briefly described in the Chapter 2. Analysis of the present manufacturing system by the production volume, by plant layout, and by the manufacturing operations, is discussed in Chapter 3.

Proposed automation considerations and improvements, such as group technology …

One-Dimensional Compressible Flow Analysis : Isentropic And Normal Shock, Su-Bo Wong

Theses

A computer program to compute and analyse one-dimensional isentropic compressible flow through variable cross-sectional area with or without a normal shock is developed. The program is written in the "FORTRAN LANGUAGE".

In this work, the area change is the predominant cause of change of flow condition. One of the advantage of this program is set on general uses for isentropic flow. In common practice, the values of the isentropic flow property ratios were tabulated or graphically presented as function of the Mach number with a specified specific heat ratio, K (normally K=1.40 was presented). With todays technology, the most versatile …

Behavior Of Channel-Shaped Reinforced Concrete Columns Under Combined Biaxial Bending And Compression, Dureseti Chidambarrao

Theses

The inelastic behavior of irregular shaped reinforced concrete columns has been a constant concern for a structural engineer, to design a safe and economic structure in modern buildings and bridge piers. The shape of the elements in a reinforced concrete structure may be used to optimize its structural strength, to make better use of the available space, to improve the aesthetic appearance of the structure, or to facilitate construction. Due to the locations of the columns, the shapes of the buildings and the nature of the applied loads, many columns are subject to combined biaxial bending and axial load.

Seven …

Failure Surface For L-Shaped Reinforced Concrete Short Columns, Mon-Chen Liu

Theses

Combined bending and axial compression for L-shaped reinforced concrete short columns is a common problem. But the present ACI Building Code (ACI 318-77), handbooks and texbooks pay no attention to this problem. A numerical analysis and computer program developed by Hsu fora reinforced concrete member subject to biaxial bending and axial load has been used Using this computer program, the interaction diagrams and failure surface were developed for L-shaped members under combined bending and axial compression. A comparison between theoretical and experimental results was included to examine the validity of failure surface.

Analysis And Tests [Of] L-Shaped Reinforced Concrete Column Under Combined Biaxial Bending And Axial Compression, Alaedin Majlesi

Theses

A total of five tests on biaxially loaded column specimens were conducted to investigate the complete behavior of load-deformation characteristics from zero load until failure. The specimens were tested under horizontal position with 60 ton hydrolic jack. Pin end was used for both ends to obtain higher accuracy of plotting curves.

Two specimens were tested with dial gages to obtain load-deflection curves and the other three specimens were tested with demec and strain gages to obtain load strain and moment-curvature curves. The strain gages were measured by weston bridge and deme-gages were measured by mechanical dial gage.

The above moment-curvature …

Simulation Of Rotational Molding, Hersel Ahdout

Theses

A computer program is written in FORTRAN IV to simulate the Rotational Molding process based on the discrete technique suggested by Progelhof and Throne. This program employs three techniques of Finite Difference, Euler's, Crank Nicolson's, and pure implicit, with their inherent accuracy and cost limits. The program has the capability of updating the variable parameters of polymer as the temperature rises, which eventuall leads to the closest simulation possible to the actual experiment.

Designing Cost Effective Pump Suction Systems Using Statistical Correlation Techniques To Estimate Vessel Elevation Costs, Neil J. Bernstein

Theses

In order to minimize total costs (investment plus operating costs) when elevating process equipment to meet hydraulic requirements, it is essential to establish cost effective and energy efficient pump suction systems. During the early stages of design of such systems it is most critical that preliminary costs be determined in a timely manner to avoid job delays. One method of accomplishing this is through the use of a cost estimating relationship for defining the price behavior of alternative pump suction systems. This thesis describes the procedure used to develop a mathematical model to predict the cost of elevating vertical drums. …