Digital Commons Network^™

Modification Of A Heat Transfer Program (Stan5) To Account For Surface Roughness And Its Application To Aerodynamic Icing, Parthasarathy R. Iyengar

Theses

In order to be able to predict the local ice accretion rate or the icing profile on an airfoil, it is necessary that a suitable heat transfer coefficient model be availabIe. A computer program has been developed which is capable of predicting the local heat transfer coefficient for a typical two dimensional icing surface. Because of the charecteristics of an icing surface, an existing computer program (STAN5) has been modified to include the effects of the following surface roughness surface curvature and boundary layer transition.

The computer program for the heat transfer coefficient has then been used with an existing …

The Application Of The Finite Element Method To Plate Stress Analysis, Yao-Zong Jen

Theses

The finite element formulation of plane elasticity and plate bending is presented and is employed in the development of the formulation of element stiffness equations and structural stiffness equations. The basic relations used to derive the finite element equations for a solid continuum are also presented. The programming organization is summarized.

The computer program cited from TAYLOR has been used to solve the deep beam problem with triangular and rectangular elements and the SAP IV program has been used to solve the plate bending problems with quadrilateral elements. Problems solved are: (1) stress distribution at the midspan of a simply …

Computer Analysis Of The Stefan Problem In Cryosurgery, Dong Hyuk Kim

Theses

Numerical solutions for determining the freezing front location vs time relation in cryosurgery are obtained by utilizing the heat transfer computer program TRUMP, which employs the explicit finite difference algorithm. The probe geometries of rectangular, cylindrical, and spherical shape with one dimensional heat flow are selected for study. Internal heat generation is considered in cylindrical and sphe¬rical probe geometries, and the difference between the solutions with and without heat generation is discussed. To verify the correctness of the TRUMP solution, comparisons are made in the freezing distance vs time relation with the Neumann's solution and the implicit enthalpy method for …

Decision Rules Applied To Spread Spectrum Signal Detection, Richard Jae Kim

Theses

Decision rules for detection of spread spectrum signals were investigated. For each decision rule, error and erasure probabilities were analyzed. The obtained data was used to plot PE vs Pe for constant signal-to-noise ratio (SNR). With the use of the probability of a word error curves the optimum threshold setting was found for a given SNR.

FSK (orthogonal signalling) and PSK (antipodal signalling) were considered for modulating the chips. When the PE vs Pe plots for FSK and PSK were compared, PSK performed better than FSK by a ratio of 6 dB.

Finally, analog and digital correlation of the received …

Prediction Of Enthalpies Of Mixing With A Unifac Model, Dinh Dang

Theses

A modified UNIFAC model is used in the correlation and prediction of enthalpies of mixing. The model requires two interaction parameters per group pair and values for 172 such pairs are presented here. Excellent prediction results are obtained with typical errors, in the temperature range of 273°K to 400°K, below 15%. For systems containing cyclic compounds, somewhat poorer results may be encountered.

Calibration Of Flame Ionization Detector For Chlorinated Hydrocarbons, Nahid Jabalameli

Theses

Relative Responses and Calibration Factors were developed for several volatile organic (mostly chlorinated) priority pollutant species in order to use one single stable compound (e.g.Benzene) for daily instrument calibration. This would replace the procedure of using a standard mixture of target compounds (25-35). This is of particular advantage because the standard mixture may not have all species stable or may show loss of some components relative to others due to wall adsorption in the standard (compressed gas) stainless steel cylinder.

The use of a single standard species was made possible by developing "accurate" relative response and calibration factors of all …

Characterization Of Tdi-Hema Homopolymer Prepared Via An Immiscible Solvent System. Synthesis And Investigation Of Oligodichloroketene, Manuel Montero

Theses

The objective of this thesis has been divided in two parts.

The first part is subdivided into two areas. First a "Universal" calibration curve for gel permeation chromatography (GPC) was construc-ted using different molecular weight standards of PMMA and MMA-HEMA co-polymers. By measuring the viscosity of the different molecular weight solutions and calculating the Vr, (retention volume), from GPC data, plots of In [ η ] Mw against Vr and In Mw against Vr are obtained. These curves can be used to obtain the molecular weight of any linear (not crosslinked) copolymer by simple measurements of viscosity and GPC data. …

Acrylamide Effects On Nerve Terminal Enzymes, Christopher S. E. Marlowe

Theses

Acrylamide causes a peripehral neuropathy. The biochemical mechanism by which it does so is the subject of intense investigation. One of the principal hypotheses for this mechanism centers on acrylamide's ability to inhibit glycolysis. This study examines the effects of in vivo exposure to acrylamide on the enzymes of the nerve terminal particle, the synaptosome.

A method for measuring glycolytic enzyme inhibition in the synaptosome was developed. Acrylamide (500 mg/kg) was administered to rats intraperitoneally. Synaptosomes were prepared by the method of Dodd et al, and lysed by sonication. GAPDH activity and NSE concentration were measured. GAPDH inhibition measured in …

An Analysis Of Costs In Welding, Shashank Gangadhar

Theses

The investment making decision for welding machinery or the selection of an economic welding process is ccmplex due to the associated indirect expenses. For conventional evaluations certain cost elements can be disregarded since they are affected equally by competing alternatives. When considering welding equipment or calculating welding costs or selecting a welding process, the indirect costs assume a significant proportion and such factors must be carefully examined.

In this paper an attempt has been made to highlight the procedure for economic justification for welding machinery and the procedure for calculating the total weld costs. The calculation of such variables as, …

Computer Graphics In Pressworking Of Sheetmetal, Manisekaran Muthu

Theses

This thesis deals with how computer graphics can be applied to the pressworking of sheetmetal. Blanking, bending and cup drawing are the major pressworking operations. A computer graphics package was developed with the aid of the Tektronix 4051 computer. This package would help the designer of pressworking operations. All the programs were written in BASIC computer programming language.

The programs written for the stock layout display the various stock layouts for circular, rectangular, square, triangular shaped components or any irregular shaped component on the computer screen. Each stock layout displays important parameters such as material utilization percentage, width of stock …

Analysis Of Deflection Temperature Under Load, Anand M. Jagani

Theses

Deflection Temperature Under Load (DTUL) is an experimental value commonly used by designers to characterize a plastic in a high temperature environment. This value is currently measured by a standard test procedure specified by the ASTM D-648. A theoretical analysis of this test was made and computer programs were developed to calculate the Deflection Temperaure of Plastics Under Load based upon temperature dependent flexural modulus data and temperature dependent thermal properties of the plastics of interest. The results obtained from the theoretical analysis agree closely with the experimental values found in the literature for two resins. An analysis of the …

An Inquiry Into Engineering Career Choice And Career Satisfaction, Gunars Bachs

Theses

The purpose of this thesis was to ascertain factors that motivate a person to study engineering, and to examine the aspects of engineering career satisfaction. This study was conducted as a survey by means of a mail questionnaire, which was distributed among graduates of New Jersey Institute of Technology. Another sample, comprised of master's degree recipients of NJIT who had received their bachelor's degree from other undergraduate schools, served as a control group.

Motivation factors and positive and negative aspects of the engineering career were established and ranked in order of their importance. A method to measure career satisfaction was …

Decentralized Optimal Control With Application To Dynamic Routing In Computer Communication Networks, Ning Wang

Dissertations

This research considers the dynamic routing problem of computer communication networks in the framework of decentralized control theory. The routing dynamics are modeled in terms of a state equation with multiple controllers. Routing, or control of message flow, is formulated as an optimal control problem with multiple decision makers. Each decision maker may have access to different set of information and work cooperatively to optimize a common system performance index.

Necessary and sufficient conditions for optimality are derived for a system with a deterministic and a stochastic traffic patterns under a linear information structure and a quadratic performance index. The …

Mathematical Models Of Unsteady Operation Of A Packed Column, Jen-Fu Chao

Dissertations

Analytical solutions of differential equations applicable to extraction, ion exchange, or adsorption processes in packed beds are presented. Results are given for three different cases. The first case accounts for adsorption phenomena only. The second one includes surface adsorption on particles and the effects of longitudinal dispersion in the bed. The third one deals with diffusion in particles and longitudinal dispersion in the bed. In the mathematical modelling of these three cases, a linear equilibrium relationship between the solute in the liquid phase and solute in the solid phase is used. The first case is solved using the single boundary …

The Settling Of An Arbitrary Number Of Spherical Particles Arranged On The Corners Of A Regular Polygon In A Viscous Fluid, Eric Robert Bixon

Dissertations

The creeping motion equation has been solved for the case of planar arrays of spheres settling under the influence of gravity in a viscous fluid. The solution is a general solution which applies to an arbitrary number of spheres. All particles will lie at the corners of a regular polygon. Thus, two particles side by side, three particles in an equilateral triangular array, or four spheres in a square array will be special cases of the general solution.

The solution has been obtained by a unique application of the method of reflections. Only a first correction to the drag has …

Measurement Of Thermal Conductivity Of Polymers Using Line Source Method, Manojkumar C. Patel

Theses

The purpose of this investigation was to evaluate the Line Source technique to measure the thermal conductivity of different molten polymers. Although the results obtained using this method are within acceptable experimental error limits, due to tec reasons explained, the results are not as accurate as claimed in the literature which describe this technique.

Behavior Of Joints Using Reinforced Polymer Concrete Under Seismic Loading, Ishac H. Kafrouni

Theses

This report describes the analysis and testing of two types of exterior beam-column joints conducted at New Jersey Institute of Technology. The testing program consisted of six beam column joints with varying strength cementing agents in the joint region: normal, high strength and polymer concrete. Half of the specimens contained 1.5 percent by volume of hooked end fibers. The study of the behavior of these beam column joints has indicated 2 cases of failures: a critical region in which the inelastic behavior was controlled by bending and, a critical region in which the inelastic behavior was controlled by high shear. …

Design Of A Photoreactor For The Oxidation Of Toxic Pollutants In Water By Ozone And Ultraviolet Radiation, Shahab Rashid Khan

Theses

A photoreactor has been designed to oxidize refractory chemicals found in water using ozone and ultraviolet radiation. The feasibility of the ozone/UV process has been examined by conducting experiments with three model compounds, namely, (1) o-chlorophenol (2) m-chlorophenol and (3) p-chloro phenol. For o-chlorophenol and p-chloro-phenol, reactions were very fast with ozone/UV oxidation and somewhat slower with m-chlorophenol. It is concluded that UV irradiation increases the decomposition of ozone and the resulting unstable intermediates are much more reactive than ozone. Ultraviolet light also helps in decomposing the substrate molecules. The effect of UV upon decomposition of ozone is more pronounced …

High Speed Puncture Impact Studies Of Structural Foam Plaques, Shashi B. Kumar

Theses

The constant velocity high speed impact study was conducted on different thermoplastic and thermoset structural foam plaques to study their impact behavior. Plaques of Noryl, Polycarbonate, Polystyrene and Polyurethane were carefully chosen to represent a true sample of the manufactured product. Test plaques were marked such that specimens could be tested for variation in location, thickness of the plaque and variation between plaques. High speed puncture impact experiment was conducted on each specimen and the results were analysed.

The test results showed that the impact performance varied significantly over the plaque. Noryl and Polycarbonate did not exhibit any correlation for …

An Interactive Procedure For Numerical Design Optimization, Jaehwan Lee

Theses

An interactive version of the numerical design optimization method of Pappas for the solution of nonlinear optimization problems is presented in this thesis, A designer intervention strategy is employed herein for interactive optimization to allow the designer to control and manage the optimization process. This procedure embodied in the interactive CADOP6 program is tested on the ten bench mark problems of Eason and Fenton to illustrate the designer intervented optimization process and to provide a comparison with the fully automated procedure of Pappas This designer intervented interactive program appears more effective and faster than the completely automated CADOP5 code on …

Spectral Analysis Of Brainstem Auditory Evoked Responses, Amir Hossein Massumkhani

Theses

In this study, the power spectrum density of the brainstem auditory evoked responses is estimated by the method of periodogram. Several techniques for reducing the leakage due to the finite length of data, smoothing the spectrum and reducing the ambiguity in the spectrum due to the resolution are studied. It is shown that a Hamming window reduces the leakage considerably and zero extention of the data to 512 points produces sufficient spectrum bandwidth. Three major peaks are observed at 100, 500, and 1000 Hz which are stable for different evoked responses. In one case with a delayed wave V, the …

Preparation And Characterization Of Blocked Diisocyanate Monomers For Dental Applications, Stephen Richard Angeli

Theses

Six new monomers were prepared and characterized. The six monomers are blocked diisocyanate compounds. In the preparation 2,4-tolylene diisocyanate was first blocked with 2=hydroxyethyl methacrylate in the para NCO position. Six different blocking agents were then used to block the ortho NCO in the preparation of the monomers: (1) p-methoxyphenol, (2) m-methoxyphenol, (3) o-methoxyphenol, (4) p-chlorophenol, (5) m-chlorophenol, and (6) o-chlorophenol. The six monomers were characterized by mp, liquid chromatography, IR, NMR, and elemental analysis. All the characterizations show that the monomers are indeed the desired products.

Experimental Investigation Of An Axisymmetric Air Jet Impinging On A Flat Plate, Saibal Basu

Theses

Experimental investigation was carried out on a circular, submerged, axisymmetric turbulent air jet-with normal impingement on a smooth, flat, square lucite plate, The flow was considered to be incompressible because the velocity of the jet was not too high, with Mach Number of the order of 0.3. Three nozzle diameters of 0.375" (9,525 mm), 0.250" (6.35 mm) and 0.125" (3.175 mm) were used with Reynolds number ranging from 7,000 to 70,000.

Various flow parameters were measured to obtain the velocity and pressure distributions at the surface of the flat lucite plate and along the centerline of the normal impinging air …

The Quasisteady Approach For Thermal Analysis Of Frost Action Below Refrigerated Warehouses, Milan Kumar Bag

Theses

The quasisteady method of analysis has been used to determine the frost depth below refrigerated warehouses. For the case when the ground temperature is different from phase change temperature, the solution is obtained by numerical integration of the equation governing the phase change process. When the ground temperature approaches the phase change temperature closed form solution is obtained. The results obtained from the quasisteady method compare well with the experimental results. The results presented in this thesis should find use in the design of the refrigerated warehouses in the colder regions of the world.

The Lewis-Matheson Method On Computer, William Raymond Castner

Theses

Lewis and Matheson, in the early 1930's, developed a manual calculation technique for the solution of multicomponent distillation problems. The object of this study was to see if there would be any advantage to using the Lewis-Matheson method, once incorporated onto a computer, over current multicomponent distillation solution techniques. The immediate advantage of using the L-M technique is that it requires fewer preliminary calculations than other computer methods. It was found that the L-M technique uses about half the execution time of a typical Newton-Raphson program, while using only one tenth the computer core (memory). This was not intended to …

Mathematical Model Of Temperature Profiles And Coking In A Crude Oil Heater Tube, Joseph C. Polimeni

Theses

A mathematical model to predict temperature profiles and coking of crude oil in furnace tubes is presented. The model assumes that the coking mechanism is due to a reaction in the laminar sublayer, whose rate depends upon the temperature profile. That profile is obtained by a numerical solution of the appropriate transport equations, with velocity profiles that may be laminar or turbulent, and including the temperature dependence of the crude oil properties. In addition, velocity and temperature profiles were adjusted when necessary to ensure closure of the heat and material balances. As a by-product of this study, a correction was …

Design Of Hvac Duct Stiffeners With Tie Rods, Raviraj Somayaji

Theses

"HVAC" ducts are made of thin gauge sheet metal. They are usually reinforced with transverse stiffeners. These stiffeners are usually made of hot rolled steel sections, such as equal leg angles or channels.

When the size of an "HVAC" duct exceeds 72 inches, additional stiffeners in the axial direction are used to reinforce the duct sheets. Tie rods are also installed, between the axial stiffeners, across the duct cross-section, to support these stiffeners. The "HVAC" ducts are subjected to either external or internal pressure. The transverse stiffeners have one or two tie rods installed, and they become statically indeterminate structures. …

Lifo Perishable Inventory (S,S,T) Model And Its Related Discount Policy, Yuan-Shyi Chiu

Theses

The objective of this thesis is to determine the optimal (s,S,T) ordering policy for a perishable inventory system with a fixed product lifetime and Poisson demand. The simulation technique is utilized to identify the optimal ordering policy which minimizes the total cost consisted of ordering, holding, shortage, and outdate costs. Upon the establishment of the optimal ordering policy, a discount policy on the outdating items is proposed to provide decision maker(s) with tradeoff between the profit and the average outdate cost.

The computer programs written in FORTRAN are designed to generate the optimal (s,S,T) ordering policy of any above-mentioned inventory …

Deposition Of Particles In Horozontal Parallel Plate Channel Due To Image Charge, Inertia, Viscosity And Gravity, Chi-Young Chu

Theses

This investigation was made to determine the effect on the deposition of particle in a horizontal parallel-plate channel due to the influences of image charge, viscosity, inertia and gravity. The flow considered was lamina, incompressible and steady. The flow patterns considered were uniform and fully developed with symmetry about the axis of the channel.

The governing equations derived for a particle were based on Newton's Second Law of motion. Since the resulting governing equations are linear second order differential equations, Runge-Kutta algorithm is used to solve the problem and graphical techniques is used to interpret the results of the numerical …

Data Acquisition And Parameter Identification In Electro-Oculography, Wolfgang Poelzleitner

Theses

Electro-Oculography (EOG) is used in clinical ophthalmology to measure the time response of the corneoretinal potential (CRP) to changes in light intensity. An automatized data acquisition and system modeling link has been developed that significantly reduces processing time presently required for EOG. The data acquisition is performed on a microprocessor based instrument, which supervises the EOG-test, measures the potential and, after completion of the test, transfers the results to a mainframe computer. Parameter identification routines provide graphical representation and mathematical models for the CRP. Both nonlinear curve fitting methods and Least Squares System Identification schemes are used.