Industrial Technology Commons^™

An Investigation Of The Factors Contributing To Measurement Uncertaintly Using A Coordinate Measurement Machine, Jayson S. Minix

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science and Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science in Engineering & Technology Management by Jayson S. Minix on December 3, 2014.

The Cadet Training Program Versus The Student Certification Program: A Study Of It- Support Training Programs At Western Kentucky University, Michael Courtney Moore

Masters Theses & Specialist Projects

Technology is a critical component of modern-day success. Advancements in technology have improved communication between individuals and companies. Technological advancements have allowed students to earn college degrees online. People who habitually use technology expect a high level of performance and support. As new technologies are implemented, such as complex web services or new operating systems, the dependence for information technology (IT) support grows in demand. Even learning curves can be cumbersome without proper assistance from IT professionals. Companies and institutions must accommodate user needs by implementing fast, efficient, and friendly support. In order to offer optimal customer support, representatives must …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

Magnetic Holding Of Synthetic Quartz For Precision Grinding, Saudin Basic

Theses and Dissertations

The objective of this research work is to investigate the practicality of magnetic workholding of non-magnetic synthetic quartz during high-speed grinding. This research work is sponsored by Quartzdyne and will be used as the starting point to applying single-piece rounding of its quartz. Hypotheses were created that would permit the authors to conclude that magnets are in fact worthwhile workholders for non-magnetic materials. Designs of Experiments were used to reject or fail to reject the null hypotheses. Experiments were carried out using a custom HAAS lathe, modified into a grinding center with an NSK live spindle, and neodymium-iron-boron magnets used …

Emergency Diesel-Electric Generator Set Maintenance And Test Periodicity, Stephen John Fehr

Engineering Management & Systems Engineering Theses & Dissertations

Manufacturer and industry recommendations vary considerably for maintenance and tests of emergency diesel-electric generator sets supporting critical operations power systems facilities. There is little consistency among sets of similar technology, and manufacturers and their representatives often provide contradictory guidance. As a result, periodicity of emergency diesel-electric generator set maintenance and tests varies considerably in practice. This work proposes and tests a research and analysis framework to develop parametric regression survival models of modern diesel-electric generator sets in emergency standby duty as a function of maintenance periodicity, test periodicity, and other predictors. Within this framework, predictors are developed from common maintenance …

Cost Performance Dynamics In Lean Production Leveling, Ahmed Deif, Hoda Elmaraghy

Industrial Technology and Packaging

Balancing of production systems is one of the main lean manufacturing principles as it reduces in-process storage and related forms of waste. A dynamic systems approach is proposed to investigate challenges of implementing production leveling and associated costs. A lean cell producing at takt time is modeled using system dynamics. The model captures various lean tools influencing production leveling and their implications. Comparative cost analysis between various leveling implementation policies for stochastic demand with multiple products is conducted. Results showed that determining the most feasible leveling policy is highly dictated by both the cost and limitations of capacity scalability. In …

Toward Automating Web Protocol Configuration For A Programmable Logic Controller Emulator, Deanna R. Fink

Theses and Dissertations

Industrial Control Systems (ICS) remain vulnerable through attack vectors that exist within programmable logic controllers (PLC). PLC emulators used as honeypots can provide insight into these vulnerabilities. Honeypots can sometimes deter attackers from real devices and log activity. A variety of PLC emulators exist, but require manual figuration to change their PLC pro le. This limits their flexibility for deployment. An automated process for configuring PLC emulators can open the door for emulation of many types of PLCs. This study investigates the feasibility of creating such a process. The research creates an automated process for figuring the web protocols of …

Dynamic Modelling Of Impact Of Lean Policies On Production Levelling Feasibility, Hoda Elmaraghy, Ahmed Deif

Industrial Technology and Packaging

A dynamic systems approach is proposed to investigate challenges of implementing production leveling and associated costs. A model of a lean cell is developed using system dynamics. The model captures various lean tools influencing production leveling. Comparative cost analysis between various leveling implementation policies for stochastic demand with multiple products is conducted. Results showed that determining the most feasible leveling policy is highly dictated by both capacity scalability cost and limitations. The developed model and revealed insights can help lean practitioners to better decide on when and how to implement production leveling as well as determine production lots sizes.

Dynamic Lean Assessment For Takt Time Implementation, Rehab M. Ali, Ahmed M. Deif

Industrial Technology and Packaging

Increasing volatility, global competitiveness, and sales crisis all force the manufacturers to commit to the journey of world-class manufacturing performance via adopting “lean systems” to enable economic success in difficult times. Among the journey to lean, one of the hardest steps is measuring the progress of lean polices implementation especially in this highly dynamic market. This paper presents a dynamic model to evaluate the degree of leanness in manufacturing firms. The model is based on system dynamics approach and presents a “leanness score” for the manufacturing system. In addition, it examines the dynamics associated with the application of “One-piece flow” …

Impact Of Dynamic Capacity Policies On Wip Level In Mix Leveling Lean Environment, Ahmed Deif, Hoda Elmaraghy

Industrial Technology and Packaging

Balancing demand's product variety in production planning is one aspect of variety management challenge. This phenomenon is described in lean systems as mix leveling. This paper approach product mix leveling problem from a dynamic perspective. A system dynamics model is developed to explore the dynamics associated with the WIP level performance at different mix leveling policies in a lean environment. The system captures different lean tools and policies. Results showed that the best WIP performance is sensitive to both the degree of lean tools implementation as well as the capacity scalability level of the system. The presented analysis showed that …

An Integrated Approach To Assess Manufacturing Greeness Level, Ahmed H. Salen, Ahmed Deif

Industrial Technology and Packaging

This paper proposes an integrated approach for relative greenness level assessment in selected manufacturing industries at the system level. The approach builds on existing methodologies to develop a multi-layer tool box called “Greenometer” which focus on the strategic comparison for cross industries evaluation as well as tactical comparison for intra-industries. The assessment tool captures the fundamental evaluation parameters of green manufacturing namely; Environment, Energy, Resources and Economy. In addition, the Greenometer employs geometric mean method (GMM) for the strategic layer and data envelopment analysis (DEA) for the tactical layer and will be used for different selected manufacturing disciplines. The proposed …

Design And Implementation Of Iso:9001 Standards At Sigma 6 Electronics, Inc., Robert Kirkpatrick, Dylan Geisen, Simon Schermerhorn

Industrial Technology and Packaging

ISO 9001 certification is a very long process that can take even the most dedicated team years to complete. For smaller companies such a process could be costly, confusing, and arduous. While many resources exist, it takes nearly the same amount of effort to tailor fit the examples as it does to create a whole new set.

The purpose of this senior project is to research examples and help fit them to a small manufacturing company, Sigma 6 Electronics, Inc. An interlinked, or combined, quality manual/procedures were chosen to aid Sigma 6 Electronics through making the documentation clear and perfectly …

A Comparative Analysis Of Spatial Visualization Ability And Drafting Models For Industrial And Technology Education Students, Petros Katsioloudis, Vukica Jovanović, Mildred Jones

Engineering Technology Faculty Publications

The article presents the comparative study on the drafting models and spatial visualization ability of industrial and technology education students in the U.S. It discusses how the study was conducted which examined the issue based on technical drawings and with regards to the impacts of model types. The results reportedly revealed three-dimensional models are effective for promoting learning, however more studies have to be conducted.

Toughening Of Poly(L-Lactic Acid) With Cu3Btc2 Metal Organic Framework Crystals, Ajay Kathuria, Mohamad G. Abiad, Rafael Auras

Industrial Technology and Packaging

Poly(l-lactic acid) (PLLA) and metal organic framework (MOF) composites were prepared by melt extrusion of PLLA with 5, 10 and 20% w/w of activated Cu₃(BTC)₂ MOF. The morphology and stability of injection-molded samples were evaluated using thermogravimetric analysis, differential scanning calorimetry (DSC), gel permeation chromatography, X-ray diffraction, and scanning electron microscopy (SEM). The composites showed improved toughness during the tensile tests as compared to the neat PLLA matrix. Toughness mechanism of the composites was studied using SEM and rheological studies. SEM images indicated that cavitation induced by debonding at the interface of PLLA and MOF particles during …

The Effects Of Football Helmet Pressure On The Shock Taken During A Controlled Impact, Sullivan Grosz

Industrial Technology and Packaging

College and NFL football teams are focusing their efforts on protecting players more than ever before. With the recent attention on concussions and the troubling long-term effects of head injuries, more research is needed to find ways to ensure players have the adequate protection. The helmets being used have a hard polycarbonate shell with four inner pads that fit tight to the player’s head. These pads are filled with air.

The purpose of the testing and project is to find an ideal air pressure that helmets need to maintain in order to protect the player to the best of its …

The Effect Of Distribution On Product Temperature Profile In Thermally Insulated Containers For Express Shipments, Jay Singh, Sanjiv Jaggia, Koushik Saha

Industrial Technology and Packaging

An uninterrupted cold chain is a continual series of storage and distribution activities that maintain a specific temperature or temperature range. Cold chain solutions typically involve excessive packaging to ensure that the desired product temperature is maintained through the distribution process, thereby increasing the logistics-related costs. There is a myriad of solutions available for shipping temperature-sensitive products, including those constructed with a variety of packaging materials as well as refrigerants. Although static characteristics for thermally insulated packaging solutions such as the R-values of package systems as well as the melting points and heat absorption rates of various refrigerants have been …

Strategic Evaluation Of University Knowledge And Technology Transfer Effectiveness, Thien Anh Tran

Dissertations and Theses

Academic knowledge and technology transfer has been growing in importance both in academic research and practice. A critical question in managing this activity is how to evaluate its effectiveness. The literature shows an increasing number of studies done to address this question; however, it also reveals important gaps that need more research. One novel approach is to evaluate the effectiveness of this activity from an organizational point of view, which is to measure how much knowledge and technology transfer from a university fulfills the mission of the institution. This research develops a Hierarchical Decision Model (HDM) to measure the contribution …

The Impact Of Knowledge Inflows On The Performance Of National Laboratories In Technological Latecomer Countries, Pattravadee Ploykitikoon

Dissertations and Theses

The national laboratories (NLs) play a critical role in the economic and social development of technological latecomer countries, yet no academic study has ever quantified how knowledge inflows and internal knowledge impact the performance of the NLs. This dissertation identifies and ranks the importance of factors pertaining to knowledge inflows and project-internal knowledge, which determine the success or failure of research projects in the NLs of Thailand. A survey of 123 project managers in the NLs, which covers 208 R&D projects, has been conducted. It consists of a questionnaire and unstructured interviews in which the project managers discuss their project(s). …

Innovation Measurement: A Decision Framework To Determine Innovativeness Of A Company, Kenny Phan

Dissertations and Theses

Innovation is one of the most important sources of competitive advantage. It helps a company to fuel the growth of new products and services, sustain incumbents, create new markets, transform industries, and promote the global competitiveness of nations. Because of its importance, companies need to manage innovation. It is very important for a company to be able to measure its innovativeness because one cannot effectively manage without measurement. A good measurement model will help a company to understand its current capability and identify areas that need improvement.

In this research a systematic approach was developed for a company to measure …

Capital Infusion, Dedication To Current Infrastructure And Workforce Development: The Three-Pronged Approach To Strategic Industrial Growth In Western New York, Clinton J. Ronan, Gina Pizziconi-Cupples

Industrial Technology Theses

One billion dollars in incentives (Cuomo, December 2012a) will infuse the opportunity for Western New York (WNY) industrial growth. It is critical two areas are carefully evaluated and supported in order to avoid a false start and accomplish a responsible, long term, reinvigorated economy: (1) leverage current viable infrastructure, specifically the Niagara Falls International Airport (NFIAP), and (2) ensure workforce development in lean operations is initiated immediately to complement technical expertise in order to recruit and sustain high paying employers. Case studies introduced in this thesis included the development of a similar regional airport compared to NFIAP as well as …