Open Access. Powered by Scholars. Published by Universities.®
Science and Technology Studies Commons™
Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Science and Technology Studies
Sensitization Behaviour Of 11-12% Cr Aisi 409 Stainless Steel During Low Heat Input Welding, Cornelis Janise Van Niekerk, Madeleine Du Toit
Sensitization Behaviour Of 11-12% Cr Aisi 409 Stainless Steel During Low Heat Input Welding, Cornelis Janise Van Niekerk, Madeleine Du Toit
Faculty of Engineering and Information Sciences - Papers: Part A
The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the …
Development Of A Dc-Lsnd Welding Process For Gmaw On Dh-36 Steel, Raymond Holder, Nathan Larkin, Huijun Li, Lenka Kuzmikova, Zengxi Pan, John Norrish
Development Of A Dc-Lsnd Welding Process For Gmaw On Dh-36 Steel, Raymond Holder, Nathan Larkin, Huijun Li, Lenka Kuzmikova, Zengxi Pan, John Norrish
Faculty of Engineering and Information Sciences - Papers: Part A
Weld induced distortion correction is a major cost within the shipbuilding industry. This paper investigates the use of an active cooling process known as Dynamically Controlled - Low Stress No Distortion (DC-LSND) Welding on DH-36 steel. Thermal profiles are obtained and distortion measurements are also achieved. Results show that the application of a localised cryogenic cooling source trailing the welding arc can significantly reduce weld induced distortion using the GMAW process. The effect of forced cooling on the weld microstructure is also observed.
Research To Establish A Systematic Approach To Safe Welding Procedure Development Using Austenitic Filler Material For Fabrication Of High Strength Steel, Lenka Kuzmikova, John Norrish, Huijun Li, Mark Callaghan
Research To Establish A Systematic Approach To Safe Welding Procedure Development Using Austenitic Filler Material For Fabrication Of High Strength Steel, Lenka Kuzmikova, John Norrish, Huijun Li, Mark Callaghan
Faculty of Engineering and Information Sciences - Papers: Part A
High strength, thermo-mechanically treated steels often require very careful control of welding procedures to ensure freedom from hydrogen assisted cold cracking (HACC) in the weld metal and heat affected zone (HAZ) whilst avoiding undue loss of heat affected zone strength. In practice this leads to restricted operating envelopes and the requirement for rigorous procedure management. An alternative approach is the use of austenitic welding consumables but whilst this may be expected to expand the process parameter envelope its use is often restricted by adherence to procedures previously developed for ferritic consumables. The current paper describes the research undertaken to establish …
Self-Shape Optimisation Of Cold-Formed Steel Closed Profiles Using Genetic Algorithms, Benoit Gilbert, Lip H. Teh, Hong Guan
Self-Shape Optimisation Of Cold-Formed Steel Closed Profiles Using Genetic Algorithms, Benoit Gilbert, Lip H. Teh, Hong Guan
Faculty of Engineering and Information Sciences - Papers: Part A
For economical benefits, optimisation of mass-produced structural steel products is widely researched. The objective is to minimise the quantity of material used without sacrificing the strength and practicality of the structural members. Current research focuses on optimising the dimensions of conventional cross-sectional shapes but rarely considers discovering new optimum shapes. This report introduces the concepts of a new optimisation method which enables the crosssection to self-shape to an optimum by using the evolution and adaptation benefits of Genetic Algorithm. The feasibility and accuracy of the method are verified by implementing it to find optimum thin-walled profiles against simple parameters for …
The Development And Manufacture Of Ultra-Thin Cast Strip Steel Products With High Residual Element Levels Via The Castrip® Process, Daniel G. Edelman, Peter C. Campbell, Chris R. Killmore, Kristin R. Carpenter, Harold R. Kaul, James G. Williams, Walter N. Blejde
The Development And Manufacture Of Ultra-Thin Cast Strip Steel Products With High Residual Element Levels Via The Castrip® Process, Daniel G. Edelman, Peter C. Campbell, Chris R. Killmore, Kristin R. Carpenter, Harold R. Kaul, James G. Williams, Walter N. Blejde
Faculty of Engineering and Information Sciences - Papers: Part B
A range of Ultra-Thin Cast Strip (UCS) sheet steels with elevated residual levels was produced via the CASTRIP twin drum casting method at Nucor Steel, Indiana. This paper examines the influence of elevated levels of copper, chromium, nickel, and phosphorous on mechanical properties, surface quality, processing, and weldability of UCS sheet steel products produced by the CASTRIP process. Increased levels of copper and phosphorous were found to strengthen UCS sheet steel due to solid solution strengthening but chromium and nickel did not. At lower coiling temperatures and low hot reductions, where processing conditions promote microstructural strengthening, copper and chromium further …