Physics Commons^™

Experimental And Computational Studies Of Functionalized Carbon Nanotubes For Use In Energy Storage Devices And Membranes, Emine S. Karaman

Dissertations

Electrolytes with good interfacial stability are a crucial component of any electrochemical device. The development of novel gel polymer electrolytes (GEs) with good interface stability and better manufacturability is important for the development of the next generation electrochemical devices. Gel electrolytes are hybrid electrolyte materials, combining benefits of both liquid and solid systems. Compared with liquid and solid electrolytes, GEs open new design opportunities and do not require rigorous encapsulation methods. In this dissertation, studies on functionalized carbon nanotubes (fCNTs) and graphene oxide (GO) doped polyvinyl alcohol (PVA) based gel electrolytes (GEs) are reported. The ionic conductivity and mechanical strength …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Intracavity Phase Interferometry Based Fiber Sensors, Luke Jameson Horstman

Optical Science and Engineering ETDs

Intracavity Phase Interferometry (IPI) is a detection technique that exploits the inherent sensitivity of a laser's frequency to the parameters of its cavity. Intracavity interferometry is orders of magnitude more sensitive than its extracavity alternatives. This dissertation improves on previous free-space proof-of-concept designs. By implementing the technique in fiber optics, using optical parametric oscillation, and investigating non-Hermitian quantum mechanics and dispersion tailoring enhancement techniques, IPI has become more applicable and sensitive. Ring and linear IPI configurations were realized in this work, both operating as bidirectional fiber optical parametric oscillators. The benefit of using externally pumped synchronous optical parametric oscillation is …

Spectral Dependence Of Deep Subwavelength Metallic Apertures In The Mid-Wave Infrared, Heath Gemar

Electronic Theses and Dissertations, 2020-

For two decades, extraordinary optical transmission (EOT) has amplified exploration into subwavelength systems. Researchers have previously suggested exploiting the spectrally selective electromagnetic field confinement of subwavelength cavities for multispectral detectors. Utilizing the finite-difference frequency domain (FDFD) method, we examine electromagnetic field confinement in both 2-dimensional and 3-dimensional scenarios from 2.5 to 6 microns (i.e., mid-wave infrared or MWIR). We explore the trade space of deep subwavelength cavities and its impact on resonant enhancement of the electromagnetic field. The studies provide fundamental understanding of the coupling mechanisms allowing for prediction of resonant spectral behavior based on cavity geometry and material properties. …

Sigesn Light-Emitting Devices: From Optical To Electrical Injection, Yiyin Zhou

Graduate Theses and Dissertations

Si photonics is a fast-developing technology that impacts many applications such as data centers, 5G, Lidar, and biological/chemical sensing. One of the merits of Si photonics is to integrate electronic and photonic components on a single chip to form a complex functional system that features compact, low-cost, high-performance, and reliability. Among all building blocks, the monolithic integration of lasers on Si encountered substantial challenges. Si and Ge, conventional epitaxial material on Si, are incompetent for light emission due to the indirect bandgap. The current solution compromises the hybrid integration of III-V lasers, which requires growing on separate smaller size substrates …

Interplay Between The Lattice And Spin Degrees Of Freedom In Magnetoelectric And Magnetic Materials, Temuujin Bayaraa

Graduate Theses and Dissertations

This dissertation contains several investigations on the cross-coupling between structural and spin degrees of freedom in multiferroic and ferrimagnetic compounds by means of first-principles calculations and ab-initio-based Monte-Carlo simulations. We start with the reviews of magnetoelectricity, ferrimagnetism, strain engineering, followed by a brief introduction to first-principles computational methods, magnetic effective Hamiltonians, and other techniques that are utilized here. The results section of the dissertation can be divided into two parts. The first half focuses on magnetoelectric effects arising from different sources, while the second half is about the ferrimagnetic nature of materials. In the first part, we examine the epitaxial …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Fabricating Nanophotonic Devices Using Nanofabrication Techniques, Scott Cummings

Student Scholar Symposium Abstracts and Posters

Nanofabrication processes are widely used to make the integrated circuits and computer chips that are ubiquitous in today’s technology. These fabrication processes can also be applied to the creation of nanophotonic devices. The ways in which we apply these fabrication techniques in the field of photonics is often constrained by the technologies used for electronics manufacturing which presents an interesting engineering challenge. These limitations include availability and cost of certain fabrication equipment and techniques required to create state-of-the-art nanophotonic devices. Through work with the University of California Irvine nano-fabrication cleanroom, we designed and fabricated various integrated photonic components including grating …

Single-Molecule Localization Microscopy Of 3d Orientation And Anisotropic Wobble Using A Polarized Vortex Point Spread Function, Tianben Ding, Matthew D. Lew

Electrical & Systems Engineering Publications and Presentations

Within condensed matter, single fluorophores are sensitive probes of their chemical environments, but it is difficult to use their limited photon budget to image precisely their positions, 3D orientations, and rotational diffusion simultaneously. We demonstrate the polarized vortex point spread function (PSF) for measuring these parameters, including characterizing the anisotropy of a molecule’s wobble, simultaneously from a single image. Even when imaging dim emitters (∼500 photons detected), the polarized vortex PSF can obtain 12 nm localization precision, 4°–8° orientation precision, and 26° wobble precision. We use the vortex PSF to measure the emission anisotropy of fluorescent beads, the wobble dynamics …

Resampling And Super-Resolution Of Hexagonally Sampled Images Using Deep Learning, Dylan Flaute, Russell C. Hardie, Hamed Elwarfalli

Electrical and Computer Engineering Faculty Publications

Super-resolution (SR) aims to increase the resolution of imagery. Applications include security, medical imaging, and object recognition. We propose a deep learning-based SR system that takes a hexagonally sampled low-resolution image as an input and generates a rectangularly sampled SR image as an output. For training and testing, we use a realistic observation model that includes optical degradation from diffraction and sensor degradation from detector integration. Our SR approach first uses non-uniform interpolation to partially upsample the observed hexagonal imagery and convert it to a rectangular grid. We then leverage a state-of-the-art convolutional neural network (CNN) architecture designed for SR …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Modeling And Characterization Of Optical Metasurfaces, Mahsa Torfeh

Masters Theses

Metasurfaces are arrays of subwavelength meta-atoms that shape waves in a compact and planar form factor. During recent years, metasurfaces have gained a lot of attention due to their compact form factor, easy integration with other devices, multi functionality and straightforward fabrication using conventional CMOS techniques. To provide and evaluate an efficient metasurface, an optimized design, high resolution fabrication and accurate measurement is required. Analysis and design of metasurfaces require accurate methods for modeling their interactions with waves. Conventional modeling techniques assume that metasurfaces are locally periodic structures excited by plane waves, restricting their applicability to gradually varying metasurfaces that …

Tailoring Plasmon Excitations In Alpha − T 3 Armchair Nanoribbons, Andrii Iurov, Liubov Zhemchuzhna, Godfrey Gumbs, Danhong Huang, Paula Fekete, Farhana Anwar, Dipendra Dahal, Nicholas Weekes

Publications and Research

We have calculated and investigated the electronic states, dynamical polarization function and the plasmon excitations for α − T ₃ nanoribbons with armchair-edge termination. The obtained plasmon dispersions are found to depend significantly on the number of atomic rows across the ribbon and the energy gap which is also determined by the nanoribbon geometry. The bandgap appears to have the strongest effect on both the plasmon dispersions and their Landau damping. We have determined the conditions when relative hopping parameter α of an α − T ₃ lattice has a strong effect on the plasmons which makes our material distinguished …

High-Frequency And Below Bandgap Anisotropic Dielectric Constants In Α-(AlXGa1-X)2O3 (0≤X≤1), Matthew Hilfiker, Ufuk Kilic, Megan Stokey, Riena Jinno, Yongjin Cho, Huili Grace Xing, Debdeep Jena, Rafal Korlacki, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

A Mueller matrix spectroscopic ellipsometry approach was used to investigate the anisotropic dielectric constants of corundum α-(Al_xGa_1-x)₂O₃ thin films in their below bandgap spectral regions. The sample set was epitaxially grown using plasma-assisted molecular beam epitaxy on m-plane sapphire. The spectroscopic ellipsometry measurements were performed at multiple azimuthal angles to resolve the uniaxial dielectric properties. A Cauchy dispersion model was applied, and high-frequency dielectric constants are determined for polarization perpendicular (ε_∞,⟂) and parallel (ε_∞,∥) to the thin film c-axis. The optical birefringence is negative throughout the …

Colloidal Quantum Dot (Cqd) Based Mid-Wavelength Infrared Optoelectronics, Shihab Bin Hafiz

Dissertations

Colloidal quantum dot (CQD) photodetectors are a rapidly emerging technology with a potential to significantly impact today’s infrared sensing and imaging technologies. To date, CQD photodetector research is primarily focused on lead-chalcogenide semiconductor CQDs which have spectral response fundamentally limited by the bulk bandgap of the constituent material, confining their applications to near-infrared (NIR, 0.7-1.0 um) and short-wavelength infrared (SWIR, 1-2.5 um) spectral regions. The overall goal of this dissertation is to investigate a new generation of CQD materials and devices that advances the current CQD photodetector research toward the technologically important thermal infrared region of 3-5 ?m, known as …

Wavelength And Power Dependence On Multilevel Behavior Of Phase Change Materials, Gary A. Sevison, Joshua A. Burrow, Haiyun Guo, Andrew M. Sarangan, Joshua R. Hendrickson, Imad Agha

Electro-Optics and Photonics Faculty Publications

We experimentally probe the multilevel response of GeTe, Ge2Sb2Te5 (GST), and 4% tungsten-doped GST (W-GST) phase change materials (PCMs) using two wavelengths of light: 1550 nm, which is useful for telecom-applications, and near-infrared 780 nm, which is a standard wavelength for many experiments in atomic and molecular physics. We find that the materials behave differently with the excitation at the different wavelengths and identify useful applications for each material and wavelength. We discuss thickness variation in the thin films used as well and comment on the interaction of the interface between the material and the substrate with regard to the …

Transport, Photoluminescence & Photoconduction Characteristics Of Free Standing Two-Dimensional Γ-Alumina & Titanium Superlattice Doped Two-Dimensional Γ-Alumina Grown By Graphene-Assisted Atomic Layer Deposition, Elaheh Kheirandish

Theses and Dissertations

This study presents a facile high-yield bottom-up fabrication, morphology, crystallographic and optoelectronic characterization of free-standing quasi-2D γ-alumina, a non van der Waals 2D material. The synthesis comprises a multi-cycle atomic layer deposition (ALD) of amorphous alumina on a porous interconnected graphene foam as a growth scaffold and removed next by annealing and sintering the alumina/graphene/alumina sandwich at ~ 800 °C in air . The crystallographic and structural characteristics of the formed non-van der Waals quasi 2D γ-alumina were studied by X-ray diffraction (XRD), selected area electron diffraction (SAED), and high-resolution transmission electron microscopy (HRTEM). This analysis revealed the synthesized 2D …

Experimental Observation Of Topological Z2 Excitonpolaritons In Transition Metal Dichalcogenide Monolayers, Mengyao Li, Ivan Sinev, Fedor Benimetskiy, Tatyana Ivanova, Ekaterina Khestanova, Svetlana Kiriushechkina, Anton Vakulenko, Sriram Guddala, Maurice Skolnick, Vinod M. Menon, Dmitry Krizhanovskii, Andrea Alù, Anton Samusev, Alexander B. Khanikaev

Publications and Research

The rise of quantum science and technologies motivates photonics research to seek new platforms with strong light-matter interactions to facilitate quantum behaviors at moderate light intensities. Topological polaritons (TPs) offer an ideal platform in this context, with unique properties stemming from resilient topological states of light strongly coupled with matter. Here we explore polaritonic metasurfaces based on 2D transition metal dichalcogenides (TMDs) as a promising platform for topological polaritonics. We show that the strong coupling between topological photonic modes of the metasurface and excitons in TMDs yields a topological polaritonic Z₂ phase. We experimentally confirm the emergence of one-way …

Efficient, Dual-Particle Directional Detection System Using A Rotating Scatter Mask, Robert Olesen, Bryan V. Egner, Darren E. Holland, Valerie Martin, James E. Bevins, Larry W. Burggraf, Buckley E. O'Day Iii

AFIT Patents

A directional radiation detection system and an omnidirectional radiation detector. The omnidirectional radiation detector detects radiation comprising at least one of: (i) gamma rays; and (ii) neutron particles. A radiation scatter mask (RSM) of the radiation detection system includes a rotating sleeve received over the omnidirectional radiation detector and rotating about a longitudinal axis. The RSM further includes: (i) a fin extending longitudinally from one side of the rotating sleeve; and (ii) a wall extending from the rotating sleeve and spaced apart from the fin having an upper end distally positioned on the rotating sleeve spaced apart or next to …

Optical Switching Performance Of Thermally Oxidized Vanadium Dioxide With An Integrated Thin Film Heater, Andrew M. Sarangan, Gamini Ariyawansa, Ilya Vitebskiy, Igor Anisimov

Electro-Optics and Photonics Faculty Publications

Optical switching performance of vanadium dioxide produced by thermal oxidation of vanadium is presented in this paper. A 100nm thick vanadium was oxidized under controlled conditions in a quartz tube furnace to produce approximately 200nm thick VO2. The substrate was appropriately coated on the front and back side to reduce reflection in the cold state, and an integrated thin film heater was fabricated to allow in-situ thermal cycling. Electrical measurements show a greater than three orders of magnitude change in resistivity during the phase transition. Optical measurements exhibit 70% transparency at 1500nm and about 15dB extinction across a wide spectral …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Computational Modeling Of Black Phosphorus Terahertz Photoconductive Antennas Using Comsol Multiphysics With Experimental Comparison Against A Commercial Lt-Gaas Emitter, Jose Isaac Santos Batista

Graduate Theses and Dissertations

This thesis presents computational models of terahertz (THz) photoconductive antenna (PCA) emitter using COMSOL Multiphysics commercial package. A comparison of the computer simulated radiated THz signal against that of an experimentally measured signal of commercial reference LT-GaAs emitter is presented. The two-dimensional model (2D) aimed at calculating the photoconductivity of a black phosphorus (BP) PCA at two laser wavelengths of 780 nm and 1560 nm. The 2D model was applied to the BP PCA emitter and the LT-GaAs devices to compare their simulated performance in terms of the photocurrent and radiated THz signal pulse. The results showed better performance of …

A Study Of Magnetism And Possible Mixed-State Superconductivity In Phosphorus-Doped Graphene, Julian E. Gil Pinzon

FIU Electronic Theses and Dissertations

Evidence of superconducting vortices, and consequently mixed-state superconductivity, has been observed in phosphorus-doped graphene at temperatures as high as 260 K. The evidence includes transport measurements in the form of resistance versus temperature curves, and magnetic measurements in the form of susceptibility and magnetic Nernst effect measurements. The drops in resistance, periodic steps in resistance, the appearance of Nernst peaks and hysteresis all point to phosphorus-doped graphene having a broad resistive region due to flux flow as well as a Berezinskii-Kosterlitz-Thouless (BKT) transition at lower temperatures.

The observation of irreversible behavior in phosphorus-doped graphene under the influence of a thermal …

On-Chip Nanoscale Plasmonic Optical Modulators, Abdalrahman Mohamed Nader Abdelhamid

Theses and Dissertations

In this thesis work, techniques for downsizing Optical modulators to nanoscale for the purpose of utilization in on chip communication and sensing applications are explored. Nanoscale optical interconnects can solve the electronics speed limiting transmission lines, in addition to decrease the electronic chips heat dissipation. A major obstacle in the path of achieving this goal is to build optical modulators, which transforms data from the electrical form to the optical form, in a size comparable to the size of the electronics components, while also having low insertion loss, high extinction ratio and bandwidth. Also, lap-on-chip applications used for fast diagnostics, …

Optical Phonon Modes, Static And High-Frequency Dielectric Constants, And Effective Electron Mass Parameter In Cubic In2O3, Megan Stokey, Rafal Korlacki, Sean Knight, Alexander Ruder, Matthew J. Hilfiker, Zbigniew Galazka, Klaus Irmscher, Yuxuan Zhang, Hongping Zhao, Vanya Darakchieva, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

A complete set of all optical phonon modes predicted by symmetry for bixbyite structure indium oxide is reported here from a combination of far-infrared and infrared spectroscopic ellipsometry, as well as first principles calculations. Dielectric function spectra measured on high quality, marginally electrically conductive melt grown single bulk crystals are obtained on a wavelength-by-wavelength (also known as point-by-point) basis and by numerical reduction of a subtle free charge carrier Drude model contribution. A four-parameter semi-quantum model is applied to determine all 16 pairs of infrared-active transverse and longitudinal optical phonon modes, including the high-frequency dielectric constant, ε_∞=4.05±0.05. The …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Development And Implementation Of A Pressure-Temperature Control System For The Physical Vapor Deposition Of Copper And Niobium From A Molybdenum Filament In The Development Of Superconducting 3d Printed Rf Cavity Particle Accelerators, Chandler J. Fleuette

Student Research Projects

This report covers the development of the pressure-temperature control system used in the production of small superconducting RF cavities for particle accelerators. To test the validity of the created program, a model for the process was created and tested. The model was used to fine tune the control system before integrating it into the lab. The end goal of the control system is to measure the pressure inside of a deposition vacuum chamber, convert that pressure to a temperature, and use that temperature in tandem with a PID controller to control the current passing though a molybdenum filament which is …

Direct Drive Solar Panel Control Circuit, Marcorios Bekheit

Physics

A control circuit is built for insulated solar electric cookers (ISEC). Power delivery and temperature safety are the focus. Using a maximum power point tracking (MPPT) algorithm, Arduino Nano, voltage and current sensors, and a buck converter, the solar panel’s output power was maximized for a direct load heat resistor with 3.5Ω for a range of solar intensities. Using a resistance temperature detector, a temperature sensor is built for safety shutoff.

Memory Module Design For High-Temperature Applications In Sic Cmos Technology, Affan Abbasi

Graduate Theses and Dissertations

The wide bandgap (WBG) characteristics of SiC play a significant and disruptive role in the power electronics industry. The same characteristics make this material a viable choice for high-temperature electronics systems. Leveraging the high-temperature capability of SiC is crucial to automotive, space exploration, aerospace, deep well drilling, and gas turbines. A significant issue with the high-temperature operation is the exponential increase in leakage current. The lower intrinsic carrier concentration of SiC (10-9 cm-3) compared to Si (1010 cm-3) leads to lower leakage over temperature. Several researchers have demonstrated analog and digital circuits designed in SiC. However, a memory module is …

Quantum Dynamical Phenomena In Non-Hermitian And Magnomechanical Systems, Saeid Vashahri Ghamsari

Graduate Theses and Dissertations

In this dissertation, we have investigated quantum dynamics via three case studies. First, we studied a system of two coupled waveguides respectively carrying optical damping and optical gain in addition to squeezing elements in one or both waveguides. Such a system is expected to generate highly entangled light fields in the two waveguides. We, however, show that the degree of the created entanglement is significantly affected by the quantum noises associated with the amplification and dissipation. Because of the noise effect, one can only have nonzero entanglement for a limited time interval. Second, we generalized the first project by considering …