Oil, Gas, and Energy Commons^™

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded, bent (three-point-bend), and cold-worked engineering materials using a new nondestructive technique based on positron annihilation spectroscopy (PAS). The proposed technique is to use γ-rays from a small MeV electron linear accelerator (Linac) to generate positrons inside the test sample via 2 pair production. This method can be used for materials characterization and investigation of defects in thick samples that usually cannot be accomplished by conventional positron technique or other …

Preparation Studies For Secondary Electron Emission Experiments On Superconducting Niobium, Anoop George, Robert A. Schill Jr.

Transmutation Sciences Materials (TRP)

Accelerator driven transmutation of waste is one complementary approach to deal with spent nuclear fuel as compared to permanent storage. High-energy protons generated by a particle accelerator collide with a heavy metal target producing neutrons. Long-lived radioactive isotopes interacting with the neutrons transmute into shorter-lived isotopes. To generate the high-energy protons efficiently, linear accelerators use multi-cell superconducting radio frequency (RF) cavities made of niobium. Superconducting niobium cavities have several advantages, including small power dissipation. The high electromagnetic fields present in these cavities may result in undesired field emission from surface imperfections with the probability of generating an avalanche of secondary …

The Electrochemical Separation Of Curium And Americium: Quaterly Report January - March 2004, David W. Hatchett, Kenneth Czerwinski

Separations Campaign (TRP)

This research report outlines the current status and progress associated with the electrochemical separation of Curium and Americium.

Data collection and analysis of the Ce³⁺/Ce⁴⁺ redox couple in various supporting electrolytes has continued. All electrolyte systems were investigated at Pt, Au, and Glassy Carbon working electrodes. Analysis of these data was accomplished by performing appropriate background subtractions to reveal net peaks due to Ce redox behavior. Successful identification of the Ce redox couple was achieved with all electrolyte/electrode systems, although a decline in peak resolution was observed with increasing acid concentration. Optimal conditions in this experiment were …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: First Quarterly Report 01/12/04-02/29/04, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the TRP proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Proposal For No-Cost Extension And Re-Scope For Unlv Trp Project: Neutron Multiplicity Measurements For The Afci Program (Advanced Fuel Cycle Initiative), Denis Beller

Transmutation Sciences Physics (TRP)

The U.S. Advanced Fuel Cycle Initiative (AFCI) is a program to develop economic and environmental methods to reduce the impact of waste from commercial nuclear fuel cycles. One concept for near-complete destruction of waste isotopes from used nuclear fuel is accelerator-driven transmutation. High-power accelerators would be used to produce high-energy charged particles, which then collide with heavy metal targets to create a cascade of neutrons. These neutrons then cause a nuclear chain reaction in subcritical systems. Fission neutrons then transmute fissile waste isotopes as well as other problematic isotopes such as technetium-99 and iodine-129. To design these systems, complex reactor …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Darrell Pepper, Sean Hsieh

Separations Campaign (TRP)

The chemical processing of used nuclear fuel is an integral component of any strategy for the transmutation of nuclear waste. Due to the large volume of material that must be handled in this first step of the transmutation process, the efficiency of the separations process is a key factor in the potential economic viability of the transmutation strategies. The ability to optimize the chemical separation systems is vital to ensure the feasibility of the transmutation program.

Systems analysis, or total systems modeling, is one of the strongest tools available to researchers for understanding and optimizing complex systems such as chemical …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process based on the traditional …

Development, Fabrication And Study Of Fullerene-Containing Carbon Material (Fcc) For Immobilization Of Iodine: Progress Reports 1-1 And 1-2, Michael Savopulo, Boris E. Burakov

Separations Campaign (TRP)

Immobilization of highly radioactive and long-lived isotope of ¹²⁹I, which is a fission product in spent nuclear fuel, requires development of new durable host-materials. Such materials should be characterized with the following principal features:

• High loading capacity to iodine incorporation
• Chemical durability and radiation resistance in order to prevent iodine release over long time (higher than 105 years) storage under conditions of underground repository of radioactive wastes
• Possibility to use iodine-doped material as a target for iodine transmutation.

Iodine is a very volatile chemical element, and even its chemically strong compounds such as AgI and CuI are not stable …

Development, Fabrication And Study Of Fullerene-Containing Carbon Material (Fcc) For Immobilization Of Iodine: Final Report #1, Michael Savopulo, Boris E. Burakov

Separations Campaign (TRP)

Immobilization of highly radioactive and long-lived isotope of ¹²⁹I, which is a fission product in spent nuclear fuel, requires development of new durable host-materials.

Iodine is a very volatile chemical element, and even its chemically strong compounds such as AgI and CuI are not stable under ultraviolet irradiation or oxidizing conditions. Therefore, development of host materials for iodine immobilization is based on unusual approach – the search and testing of new compounds which were not studied before in respect of iodine sorption and strong fixation.

Laboratory of Applied Mineralogy and Radiogeochemistry of the V.G. Khlopin Radium Institute carries out …

Development, Fabrication And Study Of Fullerene-Containing Carbon Material (Fcc) For Immobilization Of Iodine: Progress Report 1-3, Michael Savopulo, Boris E. Burakov

Separations Campaign (TRP)

During previous reporting periods we studied properties of iodine doped FCC in comparison with activated carbon. An additional goal was to investigate the possibility to convert iodine doped FCC and activated carbon into ceramic-like material avoiding iodine loss. In order to obtain ceramic based on C_xN_y with fullerene structure we decided to carry out gamma irradiation of iodine doped samples in nitrogen atmosphere (0.7 atm. N₂). It was found that iodine doping and irradiation caused principal changes in composition of FCC such as substituting of fullerene C₆₀ and graphite (both formed by benzene-like carbon …

Evaluation Of Fluorapatite As A Waste-Form Material, Dennis W. Lindle, Oliver Hemmers

Separations Campaign (TRP)

Fluorapatite, fluorinated calcium phosphate, has been identified as a potential matrix for the entombment of the zirconium fluoride fission product waste stream from the proposed FLEX process. If the efficacy of fluorapatite based waste-storage can be demonstrated, then new and potentially more-efficient options for handling and separating high-level wastes, based on fluoride-salt extraction, will become feasible. This proposal is for renewal of the UNLV portion of a dual-path research project to develop a process to fabricate a synthetic fluorapatite waste form for the ZrF₄, FP waste stream, characterize the waste form, examine its performance under environmental conditions, and …

Evaluation Of Fluorapatite As A Waste-Form Material, Dennis W. Lindle, Oliver Hemmers, Dale L. Perry

Separations Campaign (TRP)

This research attempts to develop a waste form for disposing of the zirconium fluoride fission product waste stream. Fluorapatite, a naturally-occurring fluorinated calcium phosphate, has been identified as a potential matrix for the entombment of this waste stream. If the efficacy of fluorapatite-based wastestorage can be demonstrated, then new and potentially more efficient options for handling and separating high-level wastes, based on fluoride-salt extraction, will become feasible.

The research effort has been divided along two parallel paths: the Fabrication Path, led by collaborators at the Khlopin Radium Institute (KRI) in St. Petersburg, Russia; and the Characterization Path, led by researchers …

Development Of Fluorapatite As A Waste Form: Progress Report 1-2, Boris E. Burakov

Separations Campaign (TRP)

In the framework of this stage of research the samples of Sr-fluorapatite synthesized earlier had to be studied using different methods.

These are samples of the following desired compositions:

1) Sr₁₀(PO₄)₆F₂ from precipitated precursor;

2) Sr₁₀(PO₄)₆F₂ from precipitated precursor and adding Sr(NO₃)₂;

3) Sr₈CsNd(PO₄)₆F_2.3;

4) Initial precursor for the synthesis of un-doped Sr-fluorapatite.

Development Of Fluorapatite As A Waste Form: Final Report 1, Boris E. Burakov

Separations Campaign (TRP)

Research on the apatite family of minerals to determine their suitability in the Flouride Extraction (FLEX) Process, which is part of the radioactive waste management stream.

1) KRI has fabricated and tested special high temperature furnace for fluorapatite synthesis. This equipment might be installed into glove box in order to carry out experiments with real actinides and technetium. The same equipment might be fabricated and installed in Actinide laboratory at HRC by KRI technical staff;

2) Samples of undoped polycrystalline apatite, Ca₅(PO₄)₃F, of low porosity were successfully obtained by sintering in air at 1300°C. …

Development Of Fluorapatite As A Waste Form: Progress Report 1-3, Boris E. Burakov

Separations Campaign (TRP)

In the framework of this stage of research we had to carry out synthesis and study of fluorapatite doped with fission product elements including Cs, Sr, noble metals and Zr. During previous reporting period different samples of ceramics based on Sr-fluorapatite have been synthesized. Sample of Cs-Nd-doped ceramic has been recognized as the most interesting for detailed examination by SEM and EMPA methods.

Fundamental Chemistry Of U And Pu In The Tbp-Dodecane-Nitric Acid System: Quaterly Report, Kenneth Czerwinski, Byron Bennett

Separations Campaign (TRP)

The speciation of hexavalent U and tetravalent Pu will be examined in the TBP-dodecane- nitric acid systems. This topic is chosen based on data needs for separation modeling identified by the AFCI. Emphasis will be placed on studying the influence of nitrate and acetohydroxamic acid on U and Pu speciation as well as conditions where a third phase forms in the organic phase. The organic phase will be 30 % TBP in dodecane. Equal volumes of aqueous and organic phase will be used. The speciation of the actinides in the aqueous and organic phase will be determined by a number …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator-driven transmutation subcritical systems (ADS), engineers will need to design the system to operate with a neutron multiplication factor just below that of a critical, or self-sustaining, system. This design criterion requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because larger uncertainties in the codes require larger safety margins in the design and result in a lower efficiency of the ADS transmuter. For current design efforts in the U.S., a Monte Carlo particle transport code MCNPX is used to model neutron production and transport for spallation neutron systems.

While …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Allen L. Johnson, Dale L. Perry

Transmutation Sciences Materials (TRP)

There is an active international interest in lead-bismuth eutectic and similar liquid lead systems because of the relevance to the transmutation of nuclear waste, fast reactors, and spallation neutron sources. A successful program in nuclear waste processing that includes transmutation in accelerator-driven systems and fast reactors, would significantly decrease the space requirements for geological repositories.

Materials in these systems must be able to tolerate high neutron fluxes, high temperatures, and chemical corrosion. For lead bismuth eutectic (LBE) systems, there is an additional challenge because the corrosive behaviors of materials in LBE are not well understood. Most of the available information …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of environmental and mechanical parameters on environment induced degradations of candidate target structural materials for applications in spallation-neutron-target systems, such as accelerator-driven systems for the transmutation of waste. The materials selected for evaluation and characterization are martensitic stainless steels including Alloys HT-9, EP-823 and Type 422 stainless steel (SS).

More recently, this experimental program has been expanded to evaluate the effect of molten lead-bismuth eutectic (LBE) on the corrosion behavior of target structural materials in the presence of oxygen. Since the Materials Performance Laboratory (MPL) at UNLV currently cannot …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The corrosion of structural materials is a major concern for the use of lead-bismuth eutectic (LBE) systems for nuclear applications such as in transmuter targets or fast reactors. Corrosion in liquid metal systems can occur through various processes, including, for example, dissolution, formation of inter-metallic compounds at the interface, and penetration of liquid metal along grain boundaries. Predicting the rate of these processes depends on numerous system operational factors: temperature, system geometry, thermal gradients, solid and liquid compositions, and velocity of the liquid metal, to name a few. Corrosion, along with mechanical and/or hydraulic factors, often contributes to component failure. …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The focus of this work is to determine the effect of elevated temperatures on the tensile properties of Alloy EP-823 and other martensitic alloys having similar compositions. The information obtained through this work describing the mechanism of elevated-temperature deformation will assist in developing suitable target structural materials possessing enhanced LBE corrosion resistance at process temperatures, allowing the continued development and eventual deployment of these technologies.

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic, Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Lead-bismuth eutectic (LBE) is a candidate as a spallation target in sub-critical transmutation systems and as a coolant in nuclear programs. One of the primary concerns with LBE systems is the corrosion of stainless steel, the primary structural material used in nuclear systems. To mitigate this problem, trace levels of oxygen can be introduced into the system, causing the formation of a protective oxide layer at the interface between the LBE and steel. To protect the steel components, this oxide layer must be properly maintained. However, too much oxygen will produce unwanted oxide precipitation within the coolant and elsewhere in …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

Metals and alloys, when subjected to tensile loading beyond a limiting value, can undergo plastic deformation resulting in lattice defects such as voids and dislocations. These imperfections may interact with the crystal lattice, producing a higher state of internal stresses characterized by reduced ductility. Residual stresses can also be generated in welded structures due to rapid rate of solidification, and dissimilar metallurgical microstructures between the weld and the base metals. Premature failures can be experienced in engineering metals and alloys due to the presence of these residual stresses. Specific thermal treatments commonly known as stress relief operations can relieve these …

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation: Quarterly Report, Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

This project has four components:

(1) the fabrication of a materials test apparatus with unique capabilities,

(2) comparative studies of steel corrosion under gas phase conditions comparable to the Lead Bismuth Eutectic (LBE) oxygen control conditions,

(3) isotope labeling studies, and

(4) collaborative efforts with other workers in the field.

Development Of Nanostructure Based Corrosion-Barrier Coatings On Steel For Transmutation Applications: Quaterly Report, Biswajit Das

Transmutation Sciences Materials (TRP)

During the past quarter, this project employed one graduate student and two undergraduate student researchers and made the following accomplishments :

• Acquisition of steel samples for experiments

• Design and fabrication of specialized anodization apparatus to accommodate steel samples

• Investigation of adhesiveness of aluminum on steel

• Investigation of effects of anodizing acids on steel to identify most appropriate acid and a suitable barrier material

Stress Corrosion Cracking Of Target Material, Mohammad K. Hossain

Transmutation Sciences Materials (TRP)

The primary objective of this paper is to evaluate the effect of hydrogen on environment assisted cracking of candidate target materials for transmutation applications. Transmutation refers to transformation of long-lived actinides and fission products from spent nuclear fuels (SNF), and occurs when the nucleus of an atom changes because of natural radioactive decay, nuclear fission, nuclear fusion, neutron capture, or other related processes. Martensitic Alloy EP 823 was selected to be the candidate alloy for this investigation. During the initial phase, the stress corrosion cracking (SCC) behavior of this alloy was evaluated in neutral (pH: 6-7) and acidic (pH: 2-3) …

Radiation Transport Modeling Using Parallel Computational Techniques, William Culbreth, Denis Beller

Reactor Campaign (TRP)

The second year of this project involved modeling several aspects of the LANCSE beam experiments:

• Modeling targets of varying diameter in air, in a vacuum, and in the presence of humid air;
• Modeling various proton beam profiles;
• Modeling the effects of off-axis proton beam impingement on the target;
• Modeling the asymmetry introduced by the steel table below the target;
• Modeling the effect of varying ratios of Pb to Bi and the effect of impurities; and
• Modeling the system, including other structures within the test room.

With the experience gained through modeling these systems, the UNLV researchers plan, with the assistance …

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion, Clemens Heske

Fuels Campaign (TRP)

The goal of this project is to elucidate the chemical bonding and interface formation of metal fission products with the coating materials used in state-of-the-art TRISO fuel particles. Particular emphasis is placed on an analysis of intermediate chemical phases at the interface, the intermixing/diffusion behavior, and the electronic interface structure as a function of material choice (metal and coating materials), temperature, and external stress. Furthermore, we intend to assess the chemical state of some of the metal fission products. The findings are expected to give valuable information about failure mechanisms of TRISO particles and fission product transport. Secondly, through simulating …

Interaction Between Metal Fission Products And Triso Coating Materials: A Study Of Chemical Bonding And Interdiffusion: 3rd Quarter Report, 2004, Clemens Heske

Fuels Campaign (TRP)

The goal of this project, which started in May 2004, is to elucidate the chemical bonding and interface formation of metal fission products with the coating materials used in state-of-the-art TRISO fuel particles. Particular emphasis is placed on an analysis of intermediate chemical phases at the interface, the intermixing/diffusion behavior, and the electronic interface structure as a function of material choice (metal and coating materials), temperature, and external stress.

In detail, this project is devoted to studying the interface formation of Pd, Ag, and Cs with SiC and pyrolytic carbon. Using the TRISO coating materials and single crystal references as …