Open Access. Powered by Scholars. Published by Universities.®
Polymer and Organic Materials Commons™
Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3D printing (2)
- 3D-Printing (1)
- Additive manufacturing (1)
- Anisotropic behavior (1)
- Biomechanics (1)
-
- Carbon Fiber (1)
- Compression molding (1)
- Draw (1)
- Dynamic. Separations (1)
- Elastomers (1)
- Electrophoresis (1)
- Energy efficiency (1)
- Finite element Analysis (1)
- Gradient Generation (1)
- Grayscale (1)
- Hermans Orientation Factor (1)
- Hydrogel (1)
- Industrial ecology (1)
- Manufacturing (1)
- Optimization (1)
- Orthotics (1)
- PAN fiber (1)
- PTFE (1)
- Personalized Medicine (1)
- Production rate (1)
- Rehabilitation (1)
- Seals (1)
- Solution Spinning (1)
- Surface Patterning (1)
- Viscoelasticity (1)
- Publication
- Publication Type
Articles 1 - 6 of 6
Full-Text Articles in Polymer and Organic Materials
Viscoelasticity Of Ptfe-Based Face Seals, Bo Tan
Viscoelasticity Of Ptfe-Based Face Seals, Bo Tan
Theses and Dissertations--Mechanical Engineering
PTFE-based materials are widely used in areas of tribology, particularly in seal and bearing applications because of their outstanding self-lubricating properties. Often in dynamic seal applications there is a need for ultra-low mechanical friction loss between the sealing surfaces. Due to its extremely low friction coefficient, there is interest in employing Polytetrafluoroethylene (PTFE) materials in such applications. One challenging aspect of employing PTFE is that these materials are viscoelastic and plastic. This dissertation concentrates on the modeling of viscoelastic material response when used as mechanical face seals with a focus on PTFE-based materials. First, the viscoelastic characteristics are measured through …
Electrophoresis In Heterogeneous Hydrogels And Applications In Surface Patterning, Ning Ge
Electrophoresis In Heterogeneous Hydrogels And Applications In Surface Patterning, Ning Ge
Theses and Dissertations--Mechanical Engineering
The creation of chemical micropatterns on surfaces makes it possible to add unique chemical functionality to surfaces, modifying properties such as wettability, or even adding the ability to selectively bind other molecules. The creation of biochemical surface patterning in particular is useful in a variety of fields including tissue engineering and highthroughput drug screening. There are many existing surface patterning techniques which focus on precise control over the patterned geometry, even down to submicron scale features, but they do not allow local control over chemical concentration. So the results are high resolution patterns with binary concentration. There are also existing …
Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia
Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia
Theses and Dissertations--Mechanical Engineering
3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …
Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson
Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson
Theses and Dissertations--Mechanical Engineering
This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …
Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic
Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic
Mechanical Engineering Faculty Publications
We review the process rates and energy intensities of various additive processing technologies and focus on recent progress in improving these metrics for laser powder bed fusion processing of metals, and filament and pellet extrusion processing of polymers and composites. Over the last decade, observed progress in raw build rates has been quite substantial, with laser metal processes improving by about 1 order of magnitude, and polymer extrusion processes by more than 2 orders of magnitude. We develop simple heat transfer models that explain these improvements, point to other possible strategies for improvement, and highlight rate limits. We observe a …
The Limits & Effects Of Draw On Properties And Morphology Of Pan-Based Precursor And The Resultant Carbon Fibers, Sarah Edrington
The Limits & Effects Of Draw On Properties And Morphology Of Pan-Based Precursor And The Resultant Carbon Fibers, Sarah Edrington
Theses and Dissertations--Mechanical Engineering
The process, structure, and property relationship of PAN fiber as a precursor to carbon fiber was studied. The limitations of stable spinning and property improvement associated with hot draw in solution spinning were found and quantified. Conditions were varied to generated precursor fiber up to the limit of draw, from which actual samples were collected for thermal conversion to carbon fiber. Samples of PAN and subsequent carbon fiber were characterized using tensile testing and x-ray analysis. The effects of draw on modulus and break stress, as well as the orientation of the crystalline structure of both parent precursor and resultant …