Engineering Mechanics Commons^™

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Augmenting External Surface Pressures’ Predictions On Isolated Low-Rise Buildings Using Cfd Simulations, Md Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

The aim of this paper is to enhance the accuracy of predicting time-averaged external surface pressures on low-rise buildings by utilizing Computational Fluid Dynamics (CFD) simulations. To achieve this, benchmark studies of the Silsoe cube and the Texas Tech University (TTU) experimental building are employed for comparison with simulation results. The paper is structured into three main sections. In the initial part, an appropriate domain size is selected based on the precision of mean pressure coefficients on the windward face of the cube, utilizing Reynolds Averaged Navier-Stokes (RANS) turbulence models. Subsequently, recommendations regarding the optimal computational domain size for an …

Performance Evaluation Of Gas Lift Valves Using Numerical Simulation, Felipe Simoes Maciel

LSU Master's Theses

This work aimed to assess the performance of two numerical simulation methods to replicate flow capacity test (FCT) results and predict the flow coefficient (Cv) and critical pressure ratio (Rcp) of gas lift valves (GLVs). FCT's use a modified GLV with an adjustable stem positioning system to obtain pressure as a function of flow rate for different stem positions to calculate Cv and Rcp. Therefore, this study used both a one-dimensional (1D) mechanistic model and computational fluid dynamics (CFD) to predict the same variable from the FCT without tests using modified GLVs. This methodology demonstrates accurate results, which were compared …

Atomistic Thermo-Mechanical Description Of The Deformation Behavior, Scaling Laws, And Constitutive Modeling Of Nanoporous Gold, Mohammed Hassan Yousef Saffarini

LSU Doctoral Dissertations

Metallic foams, or nanoporous (NP) metals as it is widely referred to in literature, with ligament sizes up to a few tens of nm show exceptional mechanical properties such as high strength and stiffness per weight ratio under different loading scenarios due to their high surface area to solid volume ratio. Therefore, they can be utilized in a wide range of applications making them of great interest to researchers. While their elasticity and yield strength have been the subject of several studies, very limited attention was given to the effect of size, strain rate, and temperature on the material plastic …

An Improved Foam Modeling Technique And Its Application To Petroleum Drilling And Production Practice, Yanfang Wang

LSU Doctoral Dissertations

Foam is one of the most common used multiphase fluid in Underbalanced Drilling (UBD) and Managed Pressure Drilling (MPD). Because of its low density, high capacity of lifting and carrying cuttings, low cost and compatibility with formations, foam has become more superior than the conventional drilling mud when depleted reservoir pressure, severe lost circulation, or unstable borehole are encountered. In general, the success of foam applications rely on the understanding of the fundamentals of foam rheology in downhole conditions.

Foam rheology has been studied for decades. Conventional foam rheological models such as Power Law, Bingham Plastic, Herschel-Bulkley to explain foam …

Modeling Sulfate Attack In Modern Concrete For Building Sustainable And Resilient Infrastructure, Zachary Grasley

Publications

External sulfate attack is a complex phenomenon and is manifested in the form of large expansion, cracking, and spalling depending on the exposure solution and material constituent properties. Several models were developed in the past to demonstrate sulfate attack mechanisms that account for the diffusion of sulfate ions into the porous concrete and the successive deformation triggered by the chemical reaction and precipitation of expansive agents. However, none of these models accounts for the effect of the migration of solvent water from the low solute concentration solution to high solute concentration solution driven by the osmotic pressure. Osmotic pressure is …