Engineering Science and Materials Commons^™

Turning An Organic Semiconductor Into A Low-Resistance Material By Ion Implantation, Beatrice Fraboni, Alessandra Scidà, Piero Cosseddu, Yongqiang Wang, Michael Nastasi, Silvia Milita, Annalisa Bonfiglio

Nebraska Center for Energy Sciences Research: Publications

We report on the effects of low energy ion implantation on thin films of pentacene, carried out to investigate the efficacy of this process in the fabrication of organic electronic devices. Two different ions, Ne and N, have been implanted and compared, to assess the effects of different reactivity within the hydrocarbon matrix. Strong modification of the electrical conductivity, stable in time, is observed following ion implantation. This effect is significantly larger for N implants (up to six orders of magnitude), which are shown to introduce stable charged species within the hydrocarbon matrix, not only damage as is the case …

Experimental Investigation And Thermal Modeling On Electro Discharge Drilling Of Pcd, Farnaz Nourbakhsh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This study presents an experimental investigation and finite element simulation of Electro Discharge Drilling (ED-Drilling) of Polycrystalline Diamond (PCD). PCD has many outstanding properties including uniformly high hardness, high wear resistance and strong corrosion which are the main causes of widely using PCD. While PCD has many advantages and an important role in industrial applications, its high level of hardness and wear resistance cause this material to be difficult to form and machine by using traditional machining methods. EDM as a nontraditional machining process is an effective method among other non-traditional methods for PCDs due to its low cost and …

Imaging Thermal Conductivity With Nanoscale Resolution Using A Scanning Spin Probe, Abdelghani Laraoui, Halley Aycock-Rizzo, Yang Gao, Xi Lu, Elisa Riedo, Carlos A. Meriles

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to probe nanoscale heat flow in a material is often limited by lack of spatial resolution. Here, we use a diamond-nanocrystal-hosted nitrogen-vacancy centre attached to the apex of a silicon thermal tip as a local temperature sensor. We apply an electrical current to heat up the tip and rely on the nitrogen vacancy to monitor the thermal changes the tip experiences as it is brought into contact with surfaces of varying thermal conductivity. By combining atomic force and confocal microscopy, we image phantom microstructures with nanoscale resolution, and attain excellent agreement between the thermal conductivity and topographic maps. …

Development Of A Two-Fluid Drag Law For Clustered Particles Using Direct Numerical Simulation And Validation Through Experiments, Ahmadreza Abbasi Baharanchi

FIU Electronic Theses and Dissertations

This dissertation focused on development and utilization of numerical and experimental approaches to improve the CFD modeling of fluidization flow of cohesive micron size particles. The specific objectives of this research were: (1) Developing a cluster prediction mechanism applicable to Two-Fluid Modeling (TFM) of gas-solid systems (2) Developing more accurate drag models for Two-Fluid Modeling (TFM) of gas-solid fluidization flow with the presence of cohesive interparticle forces (3) using the developed model to explore the improvement of accuracy of TFM in simulation of fluidization flow of cohesive powders (4) Understanding the causes and influential factor which led to improvements and …

Pattern Formation Of Elastic Waves And Energy Localization Due To Elastic Gratings, A. Berezovski, J. Engelbrecht, Mihhail Berezovski

Publications

Elastic wave propagation through diffraction gratings is studied numerically in the plane strain setting. The interaction of the waves with periodically ordered elastic inclusions leads to a self-imaging Talbot effect for the wavelength equal or close to the grating size. The energy localization is observed at the vicinity of inclusions in the case of elastic gratings. Such a localization is absent in the case of rigid gratings.

Me-Em Enewsbrief, September 2015, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

System And Method For Estimating States Of Spacecraft In Planet-Moon Environment, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

A method estimates a state of a spacecraft in a planet-moon environment by executing iteratively a particle filter. The particle filter comprising integrates individually states of each particle of the particle filter according to a probability-evolution equation using a model of the state of the spacecraft represented as a planar circular restricted three-body problem and determines a prior probability of each particle as a previous posterior probability of a corresponding particle during a previous iteration. A joint probability distribution of the state of the spacecraft is determines using the states of each particle and the prior probabilities of each particle …

Effect Of Surface Omniphobicity On Drying By Forced Convection, Madani A. Khan, Jeffrey Alston, Andrew Guenthner

STAR Program Research Presentations

Low energy surfaces can strongly repel both oil and water. Recently these surfaces have been fabricated on various substrates including fabric, aluminum, stainless steel and many other materials. In this experiment we explore the use of low energy surface deposition on aluminum alloy, stainless steel and silicon substrates, to enhance the drying rate of liquids removed from the surface by forced convection. We control surface roughness by substrate abrasion and by the growth of Al₂O₃ nanograss to enhance liquid repellence by use of a hierarchical texture. Liquid repellence of the substrates is measured by contact angles of …

An Estimate Of The Second-Order In-Plane Acceleration Sensitivity Of A Y-Cut Quartz Thickness-Shear Resonator, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We perform a theoretical analysis of the second-order in-plane acceleration sensitivity of a Y-cut quartz thick-ness-shear mode resonator. The second-order nonlinear theory of elasticity for anisotropic crystals is used to determine the biasing fields in the resonator under in-plane acceleration. The acceleration-induced frequency shift is determined from a per-turbation analysis based on the plate equations for small-amplitude vibrations superposed on a finite bias. We show that, whereas the first-order acceleration-induced frequency shift is zero for a structurally symmetric resonator under in-plane ac-celeration, the second-order frequency shift is nonzero and is quadratic in the acceleration. As the fourth-order nonlinear elastic constants …

Biodegradable Medical Device Having An Adjustable Degradation Rate And Methods Of Making The Same, Yuebin Guo, Michael Sealy, Meisam Salahshoor Pirsoltan

Department of Mechanical and Materials Engineering: Faculty Publications

Disclosed herein are biodegradable medical devices comprising biodegradable material (e.g., magnesium-calcium alloys) having an adjustable rate of degradation that can be used in various applications, including, but not limited to, drug delivery applications, cardiovascular applications, and orthopedic applications to make biodegradable and biocompatible devices. Also disclosed herein are methods of making biodegradable medical devices comprising biodegradable materials by using, for instance, hybrid dry cutting/hydrostatic burnishing.

Yig: Bi2o3 Nanocomposite Thin Films For Magnetooptic And Microwave Applications, M Nur-E-Alam, Mikhail Vasiliev, Kamal Alameh, Viacheslav Kotov, Victor Demidov, Dmitry Balabanov

Research outputs 2014 to 2021

Y₃Fe₅O₁₂-Bi₂O₃ composite thin films are deposited onto Gd₃Ga₅O₁₂ (GGG) substrates and their annealing crystallization regimes are optimized (in terms of both process temperatures and durations) to obtain high-quality thin film layers possessing magnetic properties attractive for a range of technological applications. The amount of bismuth oxide content introduced into these nanocomposite-type films is controlled by adjusting the RF power densities applied to both Y₃Fe₅O₁₂ and Bi₂O₃ sputtering targets during the cosputtering deposition processes. The measured material properties of …

Non-Wetting Surface-Driven High-Aspect-Ratio Crystalline Grain Growth For Efficient Hybrid Perovskite Solar Cells, Cheng Bi, Qi Wang, Yongbo Yuan, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Large-aspect-ratio grains are needed in polycrystalline thin-film solar cells for reduced charge recombination at grain boundaries; however, the grain size in organolead trihalide perovskite (OTP) films is generally limited by the film thickness. Here we report the growth of OTP grains with high average aspect ratio of 2.3–7.9 on a wide range of non-wetting hole transport layers (HTLs), which increase nucleus spacing by suppressing heterogeneous nucleation and facilitate grain boundary migration in grain growth by imposing less drag force. The reduced grain boundary area and improved crystallinity dramatically reduce the charge recombination in OTP thin films to the level in …

Me-Em Enewsbrief, June 2015, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

The Effect Of Noise On The Response Of A Vertical Cantilever Beam Energy Harvester, Michael I. Friswell, Onur Bilgen, S. Faruque Ali, Grzegorz Litak, Sondipon Adhikari

Mechanical & Aerospace Engineering Faculty Publications

An energy harvesting concept has been proposed comprising a piezoelectric patch on a vertical cantilever beam with a tip mass. The cantilever beam is excited in the transverse direction at its base. This device is highly nonlinear with two potential wells for large tip masses, when the beam is buckled. For the pre-buckled case considered here, the stiffness is low and hence the displacement response is large, leading to multiple solutions to harmonic excitation that are exploited in the harvesting device. To maximise the energy harvested in systems with multiple solutions the higher amplitude response should be preferred. This paper …

Characterizing Water As Gap Fill For Double Glazing Units, Bright Adu

Masters Theses & Specialist Projects

The use of sunlight has always been a major goal in the design and operation of commercial buildings to minimize electrical consumption of artificial lighting systems. Glazing systems designed to allow optimal visible light transmission also allow significant unwanted direct solar heat gain caused by infrared light. Conversely, glazing systems that are designed to reflect unwanted direct solar heat gain significantly reduce the transmittance of visible light through windows. The goal of this research was to characterize the performance of water as gap-fill for double-glazing units in eliminating the compromises that exist in current glazing systems with respect to light …

Local Control Robotic Surgical Devices And Related Methods, Eric Markvicka, Tom Frederick, Jack Mondry, Joe Bartels, Shane Farritor

Department of Mechanical and Materials Engineering: Faculty Publications

The various robotic medical devices include robotic devices that are disposed within a body cavity and positioned using a support component disposed through an orifice or opening in the body cavity. Additional embodiments relate to devices having arms coupled to a device body wherein the device has a minimal profile such that the device can be easily inserted through smaller incisions in comparison to other devices without such a small profile. Further embodiments relate to methods of operating the above devices.

Intensity And Resolution Enhancement Of Local Regions For Object Detection And Tracking In Wide Area Surveillance, Evan Krieger, Vijayan K. Asari, Saibabu Arigela, Theus H. Aspiras

Electrical and Computer Engineering Faculty Publications

Object tracking in wide area motion imagery is a complex problem that consists of object detection and target tracking over time. This challenge can be solved by human analysts who naturally have the ability to keep track of an object in a scene. A computer vision solution for object tracking has the potential to be a much faster and efficient solution. However, a computer vision solution faces certain challenges that do not affect a human analyst. To overcome these challenges, a tracking process is proposed that is inspired by the known advantages of a human analyst.

First, the focus of …

An Operational Performance And Safety Comparison Of Roundabouts Vs. Traditional Intersections, Vincent Spahr

Honors Theses

As the modern roundabout becomes a more popular intersection alternative in the United States, the ability of the roundabout to effectively manage traffic and to do so safely is on the forefront of engineering concerns. Despite decades of international success and credibility, regions throughout the U.S. have been hesitant to implement roundabouts in place of more traditional intersections. This case study of a series of intersections in Dublin, OH assesses the operational performance of roundabouts as it compares to that of their stop-controlled and signalized counterparts and analyzes historical crash data to evaluate the safety of the various intersection types. …

A Microscopic Study On The Corrosion Fatigue Of Ultra-Fine Grained And Conventional Al–Mg Alloy, Mala M. Sharma, Josh D. Tomedi, Jeffery M. Parks

Faculty Journal Articles

The corrosion behavior of a nanocrystalline (NC)/ultrafine grained (UFG) Al–Mg based alloy was investigated and compared to its conventional counterpart 5083(H111). The corrosion fatigue (CF) was studied with respect to pit initiation, pit location and crack propagation as a function of environment. Scanning electron microscopy (SEM) with EDS was used to analyze the fracture surface of the failed specimen with respect to pitting characteristics, crack propagation and corrosion product. Load vs. cycles to failure was measured and S/N curves were generated for the UFG Al–Mg based alloy and the conventional counterpart 5083 in air and seawater.

Methods And Systems For Handling Or Delivering Materials For Natural Orifice Surgery, Carl Nelson, Jeff Midday, Dimitry Oleynikov, Alan Goyzueta

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical systems, including systems that can be used in conjunction with medical devices used in endoscopic surgery. Certain embodiments include various material handling devices that can transport materials between the inside and the outside of an endoscopic surgery patient.

Me-Em Enewsbrief, March 2015, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical Engineering-Engineering Mechanics eNewsBrief

No abstract provided.

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …

Discontinuous Element Insertion Algorithm, Timothy James Truster

Faculty Publications and Other Works -- Civil & Environmental Engineering

An algorithm is presented for inserting zero-thickness interface elements, termed herein as “couplers”, into continuous finite element meshes in two and three dimensions. Insertion is governed solely by the mesh topology and is specified according to regions or subdomains within the overall analysis domain, a geometrically intuitive means to designate the coupler locations. The algorithm is self-contained and requires only nodal coordinates and element connectivity as input. A wide class of volume elements and interface couplers are treated within the framework. Since the algorithm is topologically-based, interfaces of arbitrary complexity are naturally accommodated. Separate treatment is given to inserting couplers …

Development And Preliminary Evaluation Of A Spray Deposition Sensing System For Improving Pesticide Application, Melissa A. Kesterson, Joe D. Luck, Michael P. Sama

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic, resistance-based sensor array and data acquisition system was developed to measure spray deposition from hydraulic nozzles. The sensor surface consisted of several parallel tin plated copper traces of varying widths with varying gap widths. The system contained an embedded microprocessor to monitor output voltage corresponding to spray deposition every second. In addition, a wireless module was used to transmit the voltage values to a remote laptop. Tests were conducted in two stages to evaluate the performance of the sensor array in an attempt to quantify the spray deposition. Initial tests utilized manual droplet placement on the sensor surface …

Enhanced Pool-Boiling Heat Transfer And Critical Heat Flux On Femtosecond Laser Processed Stainless Steel Surfaces, Cory M. Kruse, Troy Anderson, Chris Wilson, Craig Zuhlke, Dennis Alexander, George Gogos, Sidy Ndao

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper, we present an experimental investigation of pool boiling heat transfer on multiscale (micro/nano) functionalized metallic surfaces. Heat transfer enhancement in metallic surfaces is very important for large scale high heat flux applications like in the nuclear power industry. The multiscale structures were fabricated via a femtosecond laser surface process (FLSP) technique, which forms self-organized mound-like microstructures covered by layers of nanoparticles. Using a pool boiling experimental setup with deionized water as the working fluid, both the heat transfer coefficients and critical heat flux were investigated. A polished reference sample was found to have a critical heat flux …

Almost Sure Asymptotic Stabilization Of Differential Equations With Time-Varying Delay By Lévy Noise, Dezhi Liu, Weiqun Wang, Jose Luis Menaldi

Mathematics Faculty Research Publications

This paper aims to determine that the Lévy noise can stabilize the given differential equations with time-varying delay, which has generalized the Brownian motion case. An analysis is developed and sufficient conditions on the stabilization for stochastic differential equations with time-varying delay are presented. Our stabilization criteria is in terms of linear matrix inequalities (LMIs), whence the feedback controls can be designed more easily in practice.

Effects Of Forcing Time Scale On The Simulated Turbulent Flows And Turbulent Collision Statistics Of Inertial Particles, B. Rosa, H. Parishani, O. Ayala, L.-P. Wang

Engineering Technology Faculty Publications

In this paper, we study systematically the effects of forcing time scale in the large-scale stochastic forcing scheme of Eswaran and Pope ["An examination of forcing in direct numerical simulations of turbulence," Comput. Fluids 16, 257 (1988)] on the simulated flow structures and statistics of forced turbulence. Using direct numerical simulations, we find that the forcing time scale affects the flow dissipation rate and flow Reynolds number. Other flow statistics can be predicted using the altered flow dissipation rate and flow Reynolds number, except when the forcing time scale is made unrealistically large to yield a Taylor microscale flow Reynolds …

Quantification Of Plaque Stiffness By Brillouin Microscopy In Experimental Thin Cap Fibroatheroma, Giuseppe Antonacci, Ryan M. Pedrigi, Avinash Kondiboyina, Vikram V. Mehta, Ranil De Silva, Carl Paterson, Rob Krams, Peter Torok

Department of Mechanical and Materials Engineering: Faculty Publications

Plaques vulnerable to rupture are characterized by a thin and stiff fibrous cap overlaying a soft lipid-rich necrotic core. The ability to measure local plaque stiffness directly to quantify plaque stress and predict rupture potential would be very attractive, but no current technology does so. This study seeks to validate the use of Brillouin microscopy to measure the Brillouin frequency shift, which is related to stiffness, within vulnerable plaques. The left carotid artery of an ApoE^-/- mouse was instrumented with a cuff that induced vulnerable plaque development in nine weeks. Adjacent histological sections from the instrumented and control arteries …

Quantification Of Ultraprecision Surface Morphology Using An Algebraic Graph Theoretic Approach, Prahalad Rao, Satish T. S. Bukkapatnam, Zhenyu (James) Kong, Omer F. Beyca, Kenneth Case, Ranga Komanduri

Department of Mechanical and Materials Engineering: Faculty Publications

Assessment of progressive, nano-scale variation of surface morphology during ultraprecision manufacturing processes, such as fine-abrasive polishing of semiconductor wafers, is a challenging proposition owing to limitations with traditional surface quantifiers. We present an algebraic graph theoretic approach that uses graph topological invariants for quantification of ultraprecision surface morphology. The graph theoretic approach captures heterogeneous multi-scaled aspects of surface morphology from optical micrographs, and is therefore valuable for in situ real-time assessment of surface quality. Extensive experimental investigations with specular finished (Sa ~ 5 nm) blanket copper wafers from a chemical mechanical planarization (CMP) process suggest that the proposed method was …

Asphalt Composition, David Allen, Flavio Souza, Yong-Rak Kim, Roberto Soares

Department of Mechanical and Materials Engineering: Faculty Publications

A computational method is provided for predicting roadway failure due to degradation of the roadway over time as a function of the input loads, the roadway geometry, the material properties of the constituents in the asphaltic pavement, the shape, distribution, orientation and volume fractions of the constituents, and environmental conditions. The unique and new feature of the method is that it employs several physically based predictive methodologies simultaneously.