Electrical and Electronics Commons^™

Contactless Measurement Of Angular Velocity Using Circularly Polarized Antennas, Vit Sipal, Adam Narbudowicz, Max Ammann

Articles

An innovative method to measure the angular velocity using circularly polarized antennas is proposed. Due to the properties of circular polarization, the angular velocity is frequency modulated (FM) on a wireless carrier. This enables a low-cost precise continuous measurement of angular velocity using a standard FM demodulator. The hardware can be easily adapted for both high and low angular velocity values. The precise alignment angle between the antennas can be determined if the initial antenna orientation is known. The angular error is shown to be

Cloud-Induced Uncertainty For Visual Navigation, Alyssa N. Gutierrez

Theses and Dissertations

This research addresses the numerical distortion of features due to the presence of clouds in an image. The research aims to quantify the probability of a mismatch between two features in a single image, which will describe the likelihood that a visual navigation system incorrectly tracks a feature throughout an image sequence, leading to position miscalculations. First, an algorithm is developed for calculating transparency of clouds in images at the pixel level. The algorithm determines transparency based on the distance between each pixel color and the average pixel color of the clouds. The algorithm is used to create a dataset …

Impact Of Hub Location On The Performance Of Wireless Body Area Networks For Fitness Applications, Vit Sipal, Domenico Gaetano, Patrick Mcevoy, Max Ammann

Articles

This letter compares the propagation properties of Wireless Body Area Networks for three different locations (head, foot and waist) of the hub/internet gateway on the human body. The wireless channels between the hubs and four nodes (chest, back, and upper arms) are measured on a female and a male subject performing push-ups and squats. A framework using spider plots is used for cumulative performance description. The results show that the best overall performance is for hub located on the left temple and the worst overall performance is achieved for a hub on the waist. These results are expected to stimulate …

Two-Dimensional Layered Mos2 Biosensors Enable Highly Sensitive Detection Of Biomolecules, Joonhyung Lee, Piyush Dak, Yeonsung Lee, Heekyeong Park, Woong Choi, Muhammad Ashraful Alam, Sunkook Kim

Birck and NCN Publications

We present a MoS₂ biosensor to electrically detect prostate specific antigen (PSA) in a highly sensitive and label-free manner. Unlike previous MoS₂-FET-based biosensors, the device configuration of our biosensors does not require a dielectric layer such as HfO₂ due to the hydrophobicity of MoS₂. Such an oxide-free operation improves sensitivity and simplifies sensor design. For a quantitative and selective detection of PSA antigen, anti-PSA antibody was immobilized on the sensor surface. Then, introduction of PSA antigen, into the anti-PSA immobilized sensor surface resulted in a lable-free immunoassary format. Measured off-state current of the device …

Quantitative Comparison Of Time-Frequency Decomposed Gait Emg Signals, L. Patrick Mitchell

Theses and Dissertations

Falls in the senior population represent an immediate threat to both current and future generations’ quality of life. The results of falls can be disastrous, create a long road to recovery, and in many cases result in death. Hypertension represents a difficult-to-quantify condition which is known to contribute to gait and balance dysfunction. Accurate assessment of conditions such as these represents an area of primary investigative need. In order to meet this need, a new experimental setup is developed which combines time-frequency analysis with surface electromyography (sEMG) signals obtained during ambulation. 3-bit pressure data is acquired using a pressure-sensitive mat, …

Nanopulse Generators: Their Design And Application To Cancer Therapy Studies, Daniel P. Wernig

Senior Honors Theses

Effective nanopulse generators have become critical in recent decades concerning the study of subcellular affects in response to nanosecond pulsed electric fields. It has been observed that nanosecond duration electric pulses can target intracellular organelles, ultimately leading to cell apoptosis, suggesting the possibility of a new, minimally invasive, low risk cancer therapy methodology. The standard topology for developing a medical nanopulser is the Blumlein “transmission line” approach. This approach relies on the nearly infinitesimal, yet finite amount of time required for an electromagnetic field to propagate down a short transmission line. Prior to design, requirements and constraints must be defined …

Design Of Gan-Based Low-Loss Y-Branch Power Splitter, Retno Wigajatri Purnamaningsih, Irma Saraswati, Nji Raden Poespawati, Elhadj Dogheche

Makara Journal of Technology

We present a Y-branch power splitter design with a multimode section using GaN on Sapphire at telecommunication wavelength. The GaN sample optical properties were also investigated, resulting in a refractive index for the GaN layers nTE=2.289±0.001 and nTM=2.324±0.00. Optimization of the structure parameters for this structure was conducted accurately using BPM methods. The results demonstrated the possibility of realizing a GaN-based Y-branch power splitter for various applications.

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany

Makara Journal of Technology

Soekarno–Hatta Airport is the main gateway for international flights to Greater Jakarta. Its accessibility depends on the inter-city and Sedyatmo toll roads, which causes congestion in peak hours, leading to uncertainty about travel times. The Soekarno–Hatta International Airport Rail Link (SHIARL) is proposed as an alternative mass transportation project, which is expected to provide accessibility and mobility for people and goods to and from the airport. Previously, the project was unattractive to private investors as it was technically and financially unfeasible. Therefore, this research aims to improve the feasibility of the Soekarno-Hatta International Airport Rail Link (SHIARL) by using a …

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Ultra-Wideband Notched Characteristic Fed By Coplanar Waveguide, Rastanto Hadinegoro, Yuli Kurnia Ningsih, Indra Surjati

Makara Journal of Technology

In this paper, a novel Ultra-Wide Band (UWB) notch patch antenna with co-planar waveguide (CPW) fed is presented. This antenna only used one layer and the patch antenna is constructed on the first layer and back to back with CPW fed and bottom part is ground plane. The width notch is used to achieve the UWB characteristic. The results shown that the impedance bandwidth is 1130 MHz (1.662–2.792 GHz) or about 50.7% for VSWR <2.

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi

Makara Journal of Technology

Among the phenomena that occur as a result of contact between two surfaces is friction sound, in which surface roughness is of great importance. In this study, the parameter of contact stiffness is used to explain the frequency characteristic of vibration generated by the rubbing of flat surfaces under a small load. A 3-disk configuration rubbing method was used, which provides a unique characteristic of the system's frequency response function containing specific information about the rubbing vibrations. It is shown that the peak frequency of the rubbing vibration can be explained by using a two-degrees-of-freedom model incorporating the parameter of …

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman

Makara Journal of Technology

The effect of the sputtering parameters on the mechanical tribology properties of Titanium Aluminum Nitride coating on the tungsten cabide insert tool in the dry turning of tool steel has been investigated. The coating was deposited using a Direct Current magnetron sputtering system with various substrate biases (-79 to -221 V) and nitrogen flow rates (30 to 72 sccm). The dry turning test was carried out on a Computer Numeric Code machine using an optimum cutting parameter setting. The results show that the lowest flank wear (~0.4 mm) was achieved using a Titanium Aluminum Nitride-coated tool that was deposited at …

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide

Makara Journal of Technology

Total hip replacement (THR) is one of the most successful orthopedic surgical procedures for replacing a broken hip joint. In THR, wear may occur at the articulating surface of the acetabular cup and the femoral head. In Indonesia, the country with the largest Muslim population in the world, most of the inhabitants do salat (praying) every day. THR users are banned from doing salat for fear it will damage the hip joint prostheses. The previous wear calculation methods on the hip joint prostheses use the gravimetric, coordinate measuring machine (CMM), profiler, and geometric method. The disadvantages of the previous methods …

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue

Makara Journal of Technology

Efficient and continuous production of fullerenes, single-walled carbon nanotubes (SWNTs), and carbon nano-particles has been developed by the JxB arc jet method, where the Lorentz force of magnetic field jets out gaseous carbon particles to the JxB direction. In order to realize continuous mass production of these carbon clusters, the revolverinjection- type arc jet producer (RIT-AJP) has been developed. Production of fullerenes, endohedral metallo-fullerenes, SWNTs, metal-encapsulated carbon nano particles has been examined.

Uwb Precise Indoor Localization System Performance, Limitations And Its Integration, Essam Abdelkadir Elkhouly

Doctoral Dissertations

An indoor localization system that was built at University of Tennessee is extensively studied and improved. The goal of the system is to achieve mm down to sub-mm accuracy/precision.

Sub-sampling is used to alleviate the high sampling rate required for UWB signals. Current commercial direct sampling systems are still too slow or prohibitively expensive for UWB applications. We developed two different sub-sampling techniques, but the two systems suffer numerous shortcomings: low throughput, non-robustness, non-linearity. A third system is introduced that achieve both high accuracy and high through-put. Changes in the detection algorithm and the frame synchronization are developed to accommodate …

A Low-Power, Reconfigurable, Pipelined Adc With Automatic Adaptation For Implantable Bioimpedance Applications, Terence Cordell Randall

Doctoral Dissertations

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling …

An Optogenetic Brain-Machine Interface For Spatiotemporal Neuromodulation, Ryan Andrew Baumgartner

Theses and Dissertations

Direct neural stimulation has recently become a standard therapy for neurological disorders such as Parkinson's Disease, Essential Tremors, and Dystonia. Currently, deep brain electro-stimulation and neuro-pharmaceutical treatments are the dominant therapeutic options available to the public. As our understanding of brain function and neurological diseases improves, we are able to develop more advanced neuromodulation techniques. These methods could become viable treatment solutions for treating brain dysfunction. Optogenetics, first introduced by a research team led by Karl Deisseroth at Stanford University, has proved to be a versatile technique with remarkable potential to be used in treatments for brain disorders, dysfunction, and …

Improving Mri Surface Coil Decoupling To Reduce B1 Distortion, Christian K. Larson

Theses and Dissertations

As clinical MRI systems continue to advance, larger focus is being given to image

uniformity. Good image uniformity begins with generating uniform magnetic fields, which

are easily distorted by induced currents on receive-only surface coils. It has become an

industry standard to combat these induced currents by placing RF blocking networks on

surface coils. This paper explores the effect of blocking network impedance of phased array surface coils on B1 distortion. It has been found and verified, that traditional approaches for blocking network design in complex phased arrays can leave undesirable B1 distortions at 3 Tesla. The traditional approach of …

Embedded System Based Sensor Failiure Detection And Industrial Environment Controll Over Wireless Network, Innovative Research Publications Irp India, Ravishankar A, Pandian R

Innovative Research Publications IRP India

This paper focus on sensor nodes failure detection monitoring and control process via GSM and ZIGBEE wireless module. The virtual instrumentation process does measure the sensor node characteristics value and control the environment by wireless network. The industrial need does uses four types of sensor gas, radiation, temperature, and smoke sensors. The error occurrence does it’s to be detected and it will be control by the ARM controller. The performances measures does it can be monitor and also be indicated and also be control through the WSN network. The data logging of sensor monitoring and its control functions are realized …

Dynamic Channel Allocation Technique For Distributed Multi-Radio Multichannel Multi-Path Routing Protocol In Wireless Mesh Networks, Innovative Research Publications Irp India, Shreenidhi. P.L, Ranganath H R, Puttamadappa C, Basavaraju T G

Innovative Research Publications IRP India

Wireless Mesh Networks (WMNs) have gained main attraction in providing flexible network services and support to the end users. There are many efforts seen to design robust routing protocol for WMNs and solutions are proposed to standardized channel allocation techniques. There are various approaches dedicated to maximize the network though put and minimize network interface. Existing multi radio multi channel routing protocols utilize only single channel situation and static channel allocation degrades the performance of the WMNs. The challenge is to allocate channel without link interference and to improve end-to-end throughput efficiency in multipath routing for WMNs. In this paper, …

- Software Reuse, Component Clustering, Faceted Classification, Grade Strategy., Innovative Research Publications Irp India, Syed Misbahuddin

Innovative Research Publications IRP India

Some Embedded systems involve multiple processors connected by a communication medium. These processors communicate with each other exchanging short messages using some message based communication protocols such as Controller Area Network (CAN), SAE J1939 etc. With the induction of new features inside such networks, the number of messages will increase. The increase of messages may affect the network performance for a given network characteristics. Performance evaluation of a message based networks is therefore desired with increasing message load. This paper presents the performance evaluation of message based embedded communication networks. Several parameters have been estimated as function of number of …

Artificial Bee Colony-Based Design Of Optimal On-Line Self-Tuning Pidcontroller Fed Ac Drives, Innovative Research Publications Irp India, Essamudin A. Ebrahim

Innovative Research Publications IRP India

In this paper, an optimization method based on the foraging behavior of a colony of honey bees in nature was proposed. An optimized model for Proportional Integral Derivative (PID)- speed controller of 3-phase IM drives was introduced to adapt the constant gains of this classical controller. To enhance robustness of this controller, an online algorithm for self-tuning of PID controller-parameters was proposed. Experimental work was introduced using DSP and test results were obtained for several speed trajectories of 2-degree of freedom IM drive and compared with conventional PID controllers.

Split-Step Approach To Electromagnetic Propagation Through Atmospheric Turbulence Using The Modified Von Karman Spectrum And Planar Apertures, Monish Ranjan Chatterjee, Fathi H.A. Mohamed

Electrical and Computer Engineering Faculty Publications

The impact of atmospheric phase turbulence on Gaussian beam propagation along propagation paths of varying lengths is examined using multiple random phase screens. The work is motivated by research involving generation and encryption of acousto-optic chaos, and the interest in examining propagation of such chaotic waves through atmospheric turbulence. A phase screen technique is used to simulate perturbations to the refractive index of the medium through the propagation path. A power spectral density based on the modified von Karman spectrum model for turbulence is used to describe the random phase behavior of the medium.

In recent work, results for the …

A Further Look At Capacitors In Complex Arrangements, Kenneth V. Cartwright, Patrick Russell, Edit J. Kaminsky

Electrical Engineering Faculty Publications

Recently, a previous contributor showed how the delta-wye conversion may be applied to find the equivalent capacitance of five capacitors arranged in a bridge configuration. In fact, that contributor gave an algorithm for this purpose which showed that the equivalent capacitance depends upon all five capacitors. However, in this paper, we point out that there is a special case where the equivalent capacitance does not depend upon one of the five capacitors.

Finding The Minimum Input Impedance Of A Second-Order Twofold-Gain Sallen-Key Low-Pass Filter Without Calculus, Kenneth V. Cartwright, Edit J. Kaminsky

Electrical Engineering Faculty Publications

We derive an expression for the input complex impedance of a Sallen-Key second-order low-pass filter of twofold gain as a function of the natural frequency ωo and the quality factor Q. From this expression, it is shown that the filter behaves like a Frequency Dependent Negative Resistance (FDNR) element for low frequencies and as a single resistor at high frequencies. Furthermore, the minimum input impedance magnitude is found without using calculus. We discovered that the minimum input impedance magnitude is inversely proportional to Q and can be substantially less than its high-frequency value. Approximations to the minimum input impedance and …

The Progressive Development Of Turbulence Statistics And Its Impact On Wind Power Predictability, Thomas Woolmington, Keith Sunderland, Jonathan Blackledge, Michael Conlon

Articles

Wind resource assessment is a critical parameter in a diverse range of considerations within the built environment. Engineers and scientists, engaging in building design, energy conservation/application and air-quality/air-pollution control measures, need to be cognisant of how the associated wind resource imposes increased complexities in their design and modelling processes. In this regard, the morphological heterogeneities within these environments, present significant challenges to quantifying the resource and its turbulent characteristics.

This paper presents three aspects of turbulence assessment within the built environment. Firstly, an analysis of how turbulence is currently quantified is considered. The industry standard, Turbulent Intensity (TI) is compared …

Improved Performance Of Analog And Digital Acousto-Optic Modulation With Feedback Under Profiled Beam Propagation For Secure Communication Using Chaos, Fares S. Almehmadi, Monish Ranjan Chatterjee

Electrical and Computer Engineering Faculty Publications

Using intensity feedback, the closed-loop behavior of an acousto-optic hybrid device under profiled beam propagation has been recently shown to exhibit wider chaotic bands potentially leading to an increase in both the dynamic range and sensitivity to key parameters that characterize the encryption. In this work, a detailed examination is carried out vis-à-vis the robustness of the encryption/decryption process relative to parameter mismatch for both analog and pulse code modulation signals, and bit error rate (BER) curves are used to examine the impact of additive white noise.

The simulations with profiled input beams are shown to produce a stronger encryption …

Speech Perception In Reverberated Condition By Cochlear Implants, Moulesh Bhandary

Theses and Dissertations

Previous Studies for bilateral cochlear implants users examined cocktail -party setting under anechoic listening conditions. However in real world listeners always encounter problems of reverberation, which could significantly deteriorate speech intelligibility for all listeners, independent of their hearing status.

The object of this study is to investigate the effects of reverberation on the binaural benefits for speech recognition by bilateral cochlear-implant (CI) listeners.

Bilateral CI subject was tested under different reverberation conditions. IEEE recorded sentences from one male speaker mixed with either speech shaped noise (ssn), energy masking, or with 2 female competing takers (2fsn), informational masking, at different signal …

Designing And Implementing A Micro-Controller Based Primary-Side Sensing Flyback Converter For Leds Driver, Nam Nhat Tran

Graduate Theses and Dissertations

The fast development of LED and its applications has enabled a new generation of lighting device with higher efficiency and long lifespan. By employing a primary-side sensing flyback converter and the PIC18F micro-controller series, an LED driver could achieve two important features: (1) the compatibility with the available lighting fixtures, and (2) reducing unit price. The flyback converter was chosen for its simplicity, competitive low cost, and its ability to provide a constant output current, a necessarily important factor to an LED driver. Meanwhile, the PIC18F micro-controller series offer numerous advanced features which include but not limited to pulse-width modulation …