Electrical and Electronics Commons^™

Indoor Positioning Using Synchronized Ultrasonic Ofdma Signals, Julian Bartolone

Master's Theses

This paper proposes a method of short-range indoor localization using differential phase measurements of synchronized two-tone ultrasonic signals in an Orthogonal Frequency Multiple Access (OFDMA) scheme. This indoor positioning system (IPS) operates at an ultrasonic frequency of approximately 40kHz and synchronizes using an infrared signal. The OFDMA scheme allows for a receiver to process the signals from multiple transmitters continuously without the signals interfering with each other. The phases of the signals are measured using Goertzel Filters, allowing for low-complexity frequency content analysis. A MATLAB simulation using the proposed localization method is performed using four transmitter nodes in the corners …

Reference Design Of An Online Emulation And Hot-Patching Approach For Power Electronic Controller Validation, Estefano Soria Pearson

Graduate Theses and Dissertations

This thesis aims to develop a reference design of an online security system approach embedded in a power electronic controller for cybersecurity purposes. Cybersecurity in power electronics focuses on reducing vulnerabilities in the system, where most reside in the communication with the hardware devices. Although methods to secure communications lessen the probability and effects of cyber-attacks, discovering vulnerabilities is inevitable. This thesis attempts to provide a fail-safe approach to securing the system by targeting the safety of the power-electronic controller. This approach applies an additional security layer in case of a malicious or accidental controller firmware malfunction.

The online security …

A Brief Bibliometric Survey On Night Vision Bot Using Dynamic Ir And Object Detection, Devesh Abhyankar Mr., Gurumoorty Suresh Mr., Hrithik Sambhaji Karjule Mr., Parth Bhardwaj Mr., Harish Muleva Mr., Anurag Mahajan Dr.

Library Philosophy and Practice (e-journal)

This study aims to analyse the work done in the field of Night Vision Robots using IR and Object Detection from 2011 to 2021, using the bibliometric methods. This paper presents a Scopus database review on "Night Vision Bot using Dynamic IR and Object Detection". The necessity for doing this bibliometric survey is that to know how the technology in the field of mobile robotics and night vision, as well as to object detection, has evolved over the years. This paper shows the importance of Night Vision Robot from the year 2011 and continued up to 2021 April. The database …

Tractor Hacking, Jin Huang, Kyle B. Kesler

Electrical Engineering

Tractor hacking arose from tractor owners' desire for full control over the tractors they purchase. Tractor manufacturers set strict security on the electrical components of their tractors, making it difficult for tractor owners to diagnose and monitor their tractors on their own. The UltraBlue Tractor Hacking project is a solution to this problem, allowing tractor owners to perform diagnostics and monitor the equipment they purchased without having to go through dealerships. From talking to farmers, we found that they valued a diagnostic tool that allows for clearing and resetting Diagnostic Trouble Codes (DTCs), viewing diagnostic data pertaining to a specific …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Fault Modeling And Test Vector Generation For Asic Devices Exposed To Space Single Event Environment, Ahmed Mohamed

Theses and Dissertations

This work aims at providing a concise automated flow to predict the effect of Single Event Transients (SETs) on ASIC chips by developing a method to characterize the circuit susceptibility to SET pulses propagation and then generation of the required input vectors that sensitize the victim paths. A new enhanced method for SET electrical propagation modeling is proposed and compared to a previously published analytical model. The method was applied on different standard cells libraries built over XFAB Xh018 technology and verified for accuracy against simulations. The new method showed enhancement in accuracy compared with previous work in literature. Industrial …

Smart E-Bike Conversion Kit And Helmet, Megan West, Marena Trujillo, Hossein Asghari

Honors Thesis

With many state governments across the United States implementing shutdowns to prevent the spread of COVID-19, many bike retailers have seen dramatic increases in bike sales. Electric bicycles (e-bikes) have become increasingly popular as the public searches for alternatives to public transportation. Unfortunately, e-bike users assume some risk by riding bikes that are faster than conventional bicycles. While kits to convert conventional bicycles to e-bikes exist, no “smart” e-bike/helmet kit specifically designed to keep the user safe is currently available on the market. To mitigate risks, a smart e-bike conversion kit with multiple novel safety features, including auditory and visual …

Design And Fabrication Of A Microstrip Bandpass Filter In Ltcc, Allison Rucker

Electrical Engineering Undergraduate Honors Theses

The goal of the project was to design and fabricate a bandpass filter with a center frequency of 25GHz with a 2GHz bandwidth. The first step was to do the calculation to design a bandpass filter to meet these specifications along with the properties of the Dupont^TM GreenTape^TM 9K7. HFSS was then used to verify the results from the initial calculations. There was a significant error between the two results, so more tweaking was done to the calculations to get a better center frequency. After a final design was decided, the fabrication process started. Low-Temperature Co-Fired Ceramics (LLTC) …

Enercon Station Vacuum Pump Replacement, Clint Hembree, Jared D'Amico, Connor Moore, Paul Jeffrey Fontenot, Sydnee Castello, J.J. Clements

Senior Design Project For Engineers

This details the progress of the ENERCON pump replacement project as completed by the Kennesaw State University interdisciplinary senior design group. This project is a two-semester capstone effort for the engineering program at Southern Polytechnic School of Engineering, overseen by Dr. McFall during Fall 2020 and Dr. Khalid during Spring 2021 semesters. The 2020-2021 KSU Interdisciplinary Senior Design team was tasked with completing an Engineering Change Package (ECP) for existing vacuum pumps at ENERCON Station. The mechanical, electrical, and civil students worked together, performing evaluations on existing plant systems to ensure the plant could support the new vacuum pumps. By …

Side Channel Attack Counter Measure Using A Moving Target Architecture, Jithin Joseph

Electrical and Computer Engineering ETDs

A novel countermeasure to side-channel power analysis attacks called Side-channel Power analysis Resistance for Encryption Algorithms using DPR or SPREAD is investigated in this thesis. The countermeasure leverages a strategy that is best characterized as a moving target architecture. Modern field programmable gate arrays (FPGA) architectures provide support for dynamic partial reconfiguration (DPR), a feature that allows real-time reconfiguration of the programmable logic (PL). The moving target architecture proposed in this work leverages DPR to implement a power analysis countermeasure to side-channel attacks, the most common of which are referred to as differential power analysis (DPA) and correlation power analysis …

Addressing Security Challenges In Embedded Systems And Multi-Tenant Fpgas, Georgios Provelengios

Doctoral Dissertations

Embedded systems and field-programmable gate arrays (FPGAs) have become crucial parts of the infrastructure that supports our modern technological world. Given the multitude of threats that are present, the need for secure computing systems is undeniably greater than ever. Embedded systems and FPGAs are governed by characteristics that create unique security challenges and vulnerabilities. Despite their array of uses, embedded systems are often built with modest microprocessors that do not support the conventional security solutions used by workstations, such as virus scanners. In the first part of this dissertation, a microprocessor defense mechanism that uses a hardware monitor to protect …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Design, Development, And Evaluation Of Customized Electronics For Controlling A 5-Dof Magneto-Rheological Actuator Collaborative Robot, Ziqi Yang

Electronic Thesis and Dissertation Repository

In recent years, Magneto-Rheological (MR) fluids has been used in various fields such as robotics, automotive, aerospace, etc. The most common use of the MR fluids is within a clutch-like mechanism, namely an MR clutch. When mechanical input is coupled to the input part of the MR clutch, the MR clutch provides a means of delivering this mechanical input to its output, through the MR fluids. The combination of the mechanical input device and the MR clutch is called an MR actuator. The MR actuator features inherently compliance owing to the characteristic of the MR fluids while also offering higher …

Diseño E Implementación De Un Sensor De Impedancia Para La Medición De La Fracción Volumétrica En Un Tubo, Jhon William Fagua Arias, Oscar Arley Moreno Bejarano

Ingeniería Eléctrica

Este documento presenta una propuesta para comparar dos métodos, que permiten tener la medida de las fracciones volumétricas de una mezcla de fluidos bifásica, por medio de la respuesta al cambio de la capacitancia entre dos electrodos. A través de un dispositivo electrónico, llamado puente autobalanceado, se tomó el registro de una sección volumétrica y se comparó entre dos métodos de medición, con esto se obtuvo la permitividad o capacitancia del fluido, y se consiguió el volumen de forma eléctrica, el cual se contrastó con la magnitud eléctrica medida entre una lectura patrón y la obtenida en el circuito contenido …

Automated Blind Control, Daniel Nahra, Matthew Lacek, Timothy Kurczewski, William Daulton Baksa

Williams Honors College, Honors Research Projects

The objective of this project would be to design and prototype an automated, light and temperature sensing window blinds system. The device would detect temperature, both inside and outside, and incoming sunlight to determine proper window blind position for maximum energy savings. The user would also have the ability to change the settings of the blind from a remote device to a setting that they desire at any given time

Hard Hat Ambient Liability Observer (Halo), Hunter Hykes, Nathan Kish, Brian Thomson

Williams Honors College, Honors Research Projects

Capturing workplace incident information is a growing area of concern for most companies. To assist with this, the design team proposed the H.A.L.O. This design uses time-of-flight sensors connected to LEDs to create a proximity-based hazard warning system. It also records incident data using an accelerometer and micro-SD card. This helps workers avoid some of the most common workplace injuries, slips, trips, and falls and accidental collisions.

Students have created a design with engineering, and marketing requirements that accomplish this task. The proposed design allows for this monitoring and mitigation systems to be attached to hard hats. Team members developed …

Design Project: Smart Headband, John Michel, Jack Durkin, Noah Lewis

Williams Honors College, Honors Research Projects

Concussion in sports is a prevalent medical issue. It can be difficult for medical professionals to diagnose concussions. With the fast pace nature of many sports, and the damaging effects of concussions, it is important that any concussion risks are assessed immediately. There is a growing trend of wearable technology that collects data such as steps and provides the wearer with in-depth information regarding their performance. The Smart Headband project created a wearable that can record impact data and provide the wearer with a detailed analysis on their risk of sustaining a concussion. The Smart Headband uses accelerometers and gyroscopes …