Computer Engineering Commons^™

Modeling Of Quad-Station Module Cluster Tools Using Petri Nets, Aung Nay

Theses

The semiconductor industry is highly competitive, and with the recent chip shortage, the throughput of wafers has become more important than ever. One of the tools that the industry has deployed is to use of quad-station modules instead of the traditional single-station modules that allow for higher throughput and better wafer consistency by processing multiple wafers at the same time and distributing work. The industry trend is to use multiple transfer chamber robots to stack the quad-station modules in a series, particularly for etch products. In this work, the quad-station cluster tool wafer movement is modeled by using Petri net …

Design And Prototyping Of A Low-Cost High Frequency Antenna For Vicinity Coupling Devices, Benjamin Kommey, Ernest Ofosu Addo, Elvis Tamakloe

Makara Journal of Technology

This paper describes the development of a high frequency (HF) antenna for high output power vicinity coupling devices (VCDs) operating at 13.56 MHz. Key design parameters, such as RF power level, antenna size, and communication protocol, and their link to the antenna features and requirements, have been discussed. For efficient reader interrogation, detection, and recovery of transponder responses, a tuning circuit necessary to adjust the antenna power matching and resonance characteristics was designed and prototyped. The antenna was fed to an industry standard reader and evaluated for read range performance with vicinity cards. The designed antenna on the reader achieved …

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Machine Learning Approach To Investigate Ev Battery Characteristics, Shayan Falahatdoost

Major Papers

The main factor influencing an electric vehicle’s range is its battery. Battery electric vehicles experience driving range reduction in low temperatures. This range reduction results from the heating demand for the cabin and recuperation limits by the braking system. Due to the lack of an internal combustion engine-style heat source, electric vehicles' heating system demands a significant amount of energy. This energy is supplied by the battery and results in driving range reduction. Moreover, Due to the battery's low temperature in cold weather, the charging process through recuperation is limited. This limitation of recuperation is caused by the low reaction …

Towards Multipronged On-Chip Memory And Data Protection From Verification To Design And Test, Senwen Kan, Jennifer Dworak

Computer Science and Engineering Theses and Dissertations

Modern System on Chips (SoCs) generally include embedded memories, and these memories may be vulnerable to malicious attacks such as hardware trojan horses (HTHs), test access port exploitation, and malicious software. This dissertation contributes verification as well as design obfuscation solutions aimed at design level detection of memory HTH circuits as well as obfuscation to prevent HTH triggering for embedded memory during functional operation. For malicious attack vectors stemming from test/debug interfaces, this dissertation presents novel solutions that enhance design verification and securitization of an IJTAG based test access interface. Such solutions can enhance SoC protection by preventing memory test …

Digital Platform To Aid Youth Substance Abuse Prevention, Bingxuan Li

Discovery Undergraduate Interdisciplinary Research Internship

Through research and interviews, I discovered that a significant portion of students in Africa become drug addicts and drop out of school. The solution is to prevent youth substance abuse before it happens, so that more students in Africa may continue their education. With the strong motivation of expanding African student involvement in higher education, I participated DURI program to increase higher education rates in the Democratic Republic of the Congo, Africa. The local government is establishing rehabilitation centers to monitor at-risk students and prevent youth substance abuse, but due to extremely limited resources, it is critical to evaluate the …

Development Of Directed Randomization For Discussing A Minimal Security Architecture, Henrique Oyama, Dominic Messina, Keshav Kasturi Rangan, Akkarakaran Francis Leonard, Kip Nieman, Helen Durand, Katie Tyrrell, Katrina Hinzman, Michael Williamson

Chemical Engineering and Materials Science Faculty Research Publications

Strategies for mitigating the impacts of cyberattacks on control systems using a control-oriented perspective have become of greater interest in recent years. Our group has contributed to this trend by developing several methods for detecting cyberattacks on process sensors, actuators, or both sensors and actuators simultaneously using an advanced optimization-based control strategy known as Lyapunov-based economic model predictive control (LEMPC). However, each technique comes with benefits and limitations, both with respect to one another and with respect to traditional information technology and computer science-type approaches to cybersecurity. An important question to ask, therefore, is what the goal should be of …

Comparing Importance Of Knowledge And Professional Skill Areas For Engineering Programming Utilizing A Two Group Delphi Survey, John F. Hutton

Theses and Dissertations

All engineering careers require some level of programming proficiency. However, beginning programming classes are challenging for many students. Difficulties have been well-documented and contribute to high drop-out rates which prevent students from pursuing engineering. While many approaches have been tried to improve the performance of students and reduce the dropout rate, continued work is needed. This research seeks to re-examine what items are critical for programming education and how those might inform what is taught in introductory programming classes (CS1). Following trends coming from accreditation and academic boards on the importance of professional skills, we desire to rank knowledge and …

A Robust Platform For Mobile Robotics Teaching And Developing Using Arduino’S Integrated Development Environment (Ide) For Programming The Arduino Mega 2560, Sajjad Alhassan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In light of the rapid pace at which development happens with modern technology, mobile robots play an important role in our daily lives. This is due to their great importance in facilitating the affairs of life in various economic, commercial, industrial, scientific, and many other fields. In this research and project, we have restructured the microcontroller and system for one of the mobile robots (CEENBOT) that was designed by the University of Nebraska and replaced it with an Arduino Mega 2560.

The purpose of using the Arduino Mega 2560 robot is to provide alternative programming for the CEENBOT platform to …

Optimized Learning Using Fuzzy-Inference-Assisted Algorithms For Deep Learning, Miroslava Barua

Open Access Theses & Dissertations

For years, researchers in Artificial Intelligence (AI) and Deep Learning (DL) observed that performance of a Deep Learning Network (DLN) could be improved by using larger and larger datasets coupled with complex network architectures. Although these strategies yield remarkable results, they have limits, dictated by data quantity and quality, rising costs by the increased computational power, or, more frequently, by long training times on networks that are very large. Training DLN requires laborious work involving multiple layers of densely connected neurons, updates to millions of network parameters, while potentially iterating thousands of times through millions of entries in a big …

An Overview Of Bidirectional Electric Vehicles Charging System As A Vehicle To Anything (V2x) Under Cyber–Physical Power System (Cpps), Onur Elma, Umit Cali, Murat Kuzlu

Engineering Technology Faculty Publications

Nowadays, EVs are rapidly increasing in popularity, and are accepted as the vehicles of the future all over the world. The most important components are their battery and charging systems. The energy capacity of EVs’ batteries has a significant potential to supply different energy requirements. Therefore, EVs must be designed in accordance with bidirectional power flow, and Electric Vehicle Supply Equipment (EVSE) should be upgraded as Electric Vehicle Power Exchange Equipment (EVPE). This power exchange infrastructure can be called Vehicle-to-Anything (V2X). V2X will also be the key solution for energy grids of the future that will turn into a much …

Modeling, Control And Estimation Of Reconfigurable Cable Driven Parallel Robots, Adhiti Raman Thothathri

All Dissertations

The motivation for this thesis was to develop a cable-driven parallel robot (CDPR) as part of a two-part robotic device for concrete 3D printing. This research addresses specific research questions in this domain, chiefly, to present advantages offered by the addition of kinematic redundancies to CDPRs. Due to the natural actuation redundancy present in a fully constrained CDPR, the addition of internal mobility offers complex challenges in modeling and control that are not often encountered in literature.

This work presents a systematic analysis of modeling such kinematic redundancies through the application of reciprocal screw theory (RST) and Lie algebra while …

Effective Short Text Classification Via The Fusion Of Hybrid Features For Iot Social Data, Xiong Luo, Zhijian Yu, Zhigang Zhao, Wenbing Zhao, Jenq-Haur Wang

Electrical and Computer Engineering Faculty Publications

Nowadays short texts can be widely found in various social data in relation to the 5G-enabled Internet of Things (IoT). Short text classification is a challenging task due to its sparsity and the lack of context. Previous studies mainly tackle these problems by enhancing the semantic information or the statistical information individually. However, the improvement achieved by a single type of information is limited, while fusing various information may help to improve the classification accuracy more effectively. To fuse various information for short text classification, this article proposes a feature fusion method that integrates the statistical feature and the comprehensive …

Identifying And Minimizing Underspecification In Breast Cancer Subtyping, Jonathan Cheuk-Kiu Tang

Master's Theses

In the realm of biomedical technology, both accuracy and consistency are crucial to the development and deployment of these tools. While accuracy is easy to measure, consistency metrics are not so simple to measure, especially in the scope of biomedicine where prediction consistency can be difficult to achieve. Typically, biomedical datasets contain a significantly larger amount of features compared to the amount of samples, which goes against ordinary data mining practices. As a result, predictive models may fail to find valid pathways for prediction during training on such datasets. This concept is known as underspecification.

Underspecification has been more accepted …

Domain Aware Deep Learning For Wireless Physical Layer, Shuvam Chakraborty

Legacy Theses & Dissertations (2009 - 2024)

Wireless receiver design for OFDM systems is well investigated with classical signal processing tools, which lack the capacity to extract intrinsic channel effects in received signal and lead to high decoding error in receiver. Current deep learning techniques have shown improvement in such cases. But these models are mostly being developed as black box without any anchor to the theory of wireless signal propagation, which leads to surface level information gain and lacks generalizability. We propose deep learning models where the hyperparameters and learning objectives are derived from domain knowledge of wireless signal propagation. These models not only increase the …

Low Power Multi-Channel Interface For Charge Based Tactile Sensors, Samuel Hansen

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Analog front end electronics are designed in 65 nm CMOS technology to process charge pulses arriving from a tactile sensor array. This is accomplished through the use of charge sensitive amplifiers and discrete time filters with tunable clock signals located in each of the analog front ends. Sensors were emulated using Gaussian pulses during simulation. The digital side of the system uses SAR (successive approximation register) ADCs for sampling of the processed sensor signals.

Adviser: Sina Balkır

A Stacking-Based Misbehavior Detection System In Vehicular Communication Networks, Troy Green

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Over the past few decades communication systems for vehicles have continued to advance. Communications between these vehicles can be classified into safety related and non safety related messages. An example of a safety related message would be one vehicle warning others of an icy road it encountered, where a non safety related communication would be a passenger streaming a movie. In either case it's important to secure the communications so that the system continues to behave as expected. In this thesis we propose a Misbehavior Detection System (MDS), which is a system that monitors messages sent between vehicles, and detects …

A Low-Power, Low-Area 10-Bit Sar Adc With Length-Based Capacitive Dac, Zhili Pan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A 2.5 V single-ended 10-bit successive-approximation-register analog-to-digital converter (SAR ADC) based on the TSMC 65 nm CMOS process is designed with the goal of achieving low power consumption (33.63 pJ/sample) and small area (2874 µm^2 ). It utilizes a novel length-based capacitive digital-to-analog converter (CDAC) layout to achieve low total capacitance for power efficiency, and a custom static asynchronous logic to free the dependence on a high-frequency external clock source. Two test chips have been designed and the problems found through testing the first chip are analyzed. Multiple improved versions of the ADC with minor variations are implemented on the …

Performance Comparison Of Several Control Algorithms For Tracking Control Of Pantograph Mechanism, Laylaa Mahmoud Eng, Mohamed Shamseldin Dr, Mohamed Sallam Dr, Abdelghany Mohamed Prof

Future Engineering Journal

A sort of parallel manipulator known as a pantograph robot mechanism was created primarily for industrial requests that required high precision and satisfied speed. While tracking a chosen trajectory profile requires a powerful controller. Because it has four active robot links and one robot passive link in place of just two links like the open chain does, it can carry more loads than the open chain robot mechanism while maintaining accuracy and stability. The calculated model for a closed chain pantograph robot mechanism presented in this paper takes into account the boundary conditions. For the purpose of simulating the dynamics …

Relative Rate Observer Self-Tuning Of Fuzzy Pid Virtual Inertia Control For An Islanded Microgrid, Ahmed H. Mohamed, Helmy M. El Zoghby, Mohiy Bahgat, A. M. Abdel Ghany

Future Engineering Journal

Expanding the usage of renewable energy in islanded microgrids leads to a reduction in its total inertia. Low inertia microgrids have difficulties in voltage and frequency control. That affected saving its stability and preventing a blackout. To improve low inertia islanded microgrids' dynamic response and save their stability, this paper presented relative rate observer self-tuning fuzzy PID (RROSTF-PID) based on virtual inertia control (VIC) for an islanded microgrid with a high renewable energy sources (RESs) contribution. RROSTF-PID based on VIC's success in showing remarkable improvement in the microgrid's dynamic response and enhancement of its stability. Moreover, it handles different contingency …

A Framework For Stable Robot-Environment Interaction Based On The Generalized Scattering Transformation, Kanstantsin Pachkouski

Electronic Thesis and Dissertation Repository

This thesis deals with development and experimental evaluation of control algorithms for stabilization of robot-environment interaction based on the conic systems formalism and scattering transformation techniques. A framework for stable robot-environment interaction is presented and evaluated on a real physical system. The proposed algorithm fundamentally generalizes the conventional passivity-based approaches to the coupled stability problem. In particular, it allows for stabilization of not necessarily passive robot-environment interaction. The framework is based on the recently developed non-planar conic systems formalism and generalized scattering-based stabilization methods. A comprehensive theoretical background on the scattering transformation techniques, planar and non-planar conic systems is presented. …

Computer Engineering Education, Marilyn Wolf

CSE Conference and Workshop Papers

Computer engineering is a rapidly evolving discipline. How should we teach it to our students?

This virtual roundtable on computer engineering education was conducted in summer 2022 over a combination of email and virtual meetings. The panel considered what topics are of importance to the computer engineering curriculum, what distinguishes computer engineering from related disciplines, and how computer engineering concepts should be taught.

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

Rdlnn-Based Image Forgery Detection And Forged Region Detection Using Mot, Akram Hatem Saber, Mohd Ayyub Khan, Basim Galeb Mejbel

Karbala International Journal of Modern Science

Image forgery detection TEMPhas become an emerging research area due to the increasing number of forged images circulating on the internet and other social media, which leads to legal and social issues. Image forgery detection includes the classification of an image as forged or authentic and as well as localizing the forgery wifin the image. In this paper, we propose a Regression Deep Learning Neural Network (RDLNN) based image forgery detection followed by Modified Otsu Thresholding (MOT) algorithm to detect the forged region. The proposed model comprises five steps that are preprocessing, image decomposition, feature extraction, classification and block matching. …

Compilation Optimizations To Enhance Resilience Of Big Data Programs And Quantum Processors, Travis D. Lecompte

LSU Doctoral Dissertations

Modern computers can experience a variety of transient errors due to the surrounding environment, known as soft faults. Although the frequency of these faults is low enough to not be noticeable on personal computers, they become a considerable concern during large-scale distributed computations or systems in more vulnerable environments like satellites. These faults occur as a bit flip of some value in a register, operation, or memory during execution. They surface as either program crashes, hangs, or silent data corruption (SDC), each of which can waste time, money, and resources. Hardware methods, such as shielding or error correcting memory (ECM), …

Redefining Research In Nanotechnology Simulations: A New Approach To Data Caching And Analysis, Darin Tsai, Alan Zhang, Aloysius Rebeiro

The Journal of Purdue Undergraduate Research

No abstract provided.

Energy Efficient Routing Technique In Underwater Wireless Sensor Networks, Yashwanth N Dr.

Technical Collection

Wireless sensor networks can improve the efficiency for collecting information in underwater environments. In the past, researchers collected data under the sea by the way of both sending oceanographic equipments into water and recovering it at the end of mission. The whole process often took long time so real-time services cannot be supported. Wireless sensor networks can detect events and transmit the collected data to a data center immediately. However, current terrestrial routing protocols are not suitable in the underwater sensor networks. Due to unique characteristics in the water, the transmission performance and energy of the routing protocols are inefficient. …

Blockchain And Federated Learning-Based Security Solutions For Telesurgery System: A Comprehensive Review, Sachi Chaudjary, Riya Kakkar, Rajesh Gupta, Sudeep Tanwar, Smita Agrawal, Ravi Sharma

Turkish Journal of Electrical Engineering and Computer Sciences

The advent of telemedicine with its remote surgical procedures has effectively transformed the working of healthcare professionals. The evolution of telemedicine facilitates the remote monitoring of patients that lead to the advent of telesurgery systems, i.e. one of the most critical applications in telemedicine systems. Apart from gaining popularity, the telesurgery system may encounter security and trust issues of patients? data while communicating with the surgeon for their remote treatment. Motivated by this, we have presented a comprehensive survey on secure telesurgery systems comprising healthcare, surgical robots, traditional telesurgery systems, and the role of artificial intelligence to deal with the …

Skin Lesion Segmentation By Using Object Detection Networks, Deeplab3+, And Active Contours, Fatemeh Bagheri, Mohammad Jafar Tarokh, Majid Ziaratban

Turkish Journal of Electrical Engineering and Computer Sciences

Developing an automatic system for detection, segmentation, and classification of skin lesions is very useful to aid well-timed diagnosis of skin diseases. Lesion segmentation is a crucial task for automated diagnosis of skin cancers, as it affects significantly the accuracy of the subsequent steps. Varieties in sizes and locations of lesions, and the lesions with low-contrast boundaries make this task very challenging. In this paper, a three-stage CNN-based method is presented for accurate segmentation of lesions from dermoscopic images. At the first step, normalization, approximate locations and sizes of lesions are estimated. Due to the importance of the normalization stage, …

Computationally Efficient Predictive Torque Control Strategies Without Weighting Factors, Emrah Zerdali̇, Mert Altintaş, Ali̇ Bakbak, Erkan Meşe

Turkish Journal of Electrical Engineering and Computer Sciences

Predictive torque control (PTC) is a promising control method for electric machines due to its simplicity, fast dynamics, ability to handle nonlinearities, and easy inclusion of additional control objectives. The main challenge in conventional PTC design is to determine the weighting factors in the cost function. These weighting factors are generally chosen by the trial-and-error method or metaheuristic optimization algorithms, but these methods may not apply the optimum voltage vectors according to changing operating conditions. There are also several studies on the elimination of the weighting factors. This paper proposes two weighting factorless PTC strategies with lower computational complexities than …