Structural Engineering Commons^™

An Assessment Of The Accuracy Of The Euler-Bernoulli Beam Theory For Calculating Strain And Deflection In Composite Sandwich Beams, Qhinhon D. Ho

University of New Orleans Theses and Dissertations

This study focuses on assessing the accuracy of the Euler-Bernoulli beam theory as computational bases to calculate strain and deflection of composite sandwich beam subjected to three-point and four-point bending. Two groups of composite sandwich beams tests results will be used for comparison purposes. Mechanical properties for the laminated skin are provided by researchers from University of Mississippi (Ellen Lackey et al., 2000). Mechanical properties for the balsa wood core are provided by Alcan Baltek Corporation. Appropriate material properties and test geometries are then used in the Euler-Bernoulli-based algorithm in order to generate analytical data for comparison to experimental data …

Independency Of Elasticity On Residual Stress Of Room Temperature Rolled Stainless Steel 304 Plates For Structure Materials, Parikin Parikin, David Allen

Makara Journal of Technology

Mechanical strengths of materials are widely expected in general constructions of any building. These properties depend on its formation (cold/hot forming) during fabrication. This research was carried out on cold-rolled stainless steel (SS) 304 plates, which were deformed to 0, 34, 84, and 152% reduction in thickness. The tests were conducted using Vickers method. Ultra micro indentation system (UMIS) 2000 was used to determine the mechanical properties of the material, i.e.: hardness, modulus elasticity, and residual stresses. The microstructures showed lengthening outcropping due to stress corrosion cracking for all specimens. It was found that the tensile residual stress in a …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

Improvement Of Quality Of Carica Papaya L. With Clove Oil As Preservative In Edible Coating Technology, Eny Kusrini, Anwar Usman, Chrispine Deksita Wisakanti, Rita Arbianti, Dedy Alharis Nasution

Makara Journal of Technology

We have studied utilization of essential clove oil, extracted from clove buds by hydrodistillation, as preservative in edible packaging technology. Preservative of essential clove oil was applied on chopped papaya fruits by using two methods, namely spray and brush. The effects of concentration of clove oil from 0.05 to 0.20% on the preservation of papaya fruits (Carica papaya L.) at room temperature (25 °C) were also evaluated. Physicochemical and in vitro microbiological activities on the papaya fruits that were stored at 25 oC and 85-90% relative humidity were investigated in details. The results indicate that the clove oil at concentration …

Oxidation Process Of H 2 O /Uv For Cod Reduction Of Wastewater From Soybean Tofu Production, Komala Pontas, Abrar Muslim

Makara Journal of Technology

Chemical Oxygen Demand (COD) reduction of wastewater from soybean tofu production was studied by conducting advanced oxidation process (AOP) using hydrogen peroxide with UV radiation catalysts in a closed cylindrical glass reactor. The hydroxyl radical (*OH) concentration from H2O2 decomposition was modeled, and exponential trends were found for the *OH concentration over radiation time and operation temperature. As a result, it was found that the maximal *OH concentration was 0.209 mol L-1 at 240 minutes and 50 °C. The *OH concentration exponentially increased following rise in operation temperature. The H2O2/UV AOP application reduced COD concentration to approximately 42.41% from 10,545 …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Calibration Of Numerical Model For Shoreline Change Prediction Using Satellite Imagery Data, Sigit Sutikno, Keisuke Murakami, Dwi Puspo Handoyo, Manyuk Fauzi

Makara Journal of Technology

This paper presents a method for calibration of numerical model for shoreline change prediction using satellite imagery data in muddy beach. Tanjung Motong beach, a muddy beach that is suffered high abrasion in Rangsang Island, Riau province, Indonesia was picked as study area. The primary numerical modeling tool used in this research was GENESIS (GENEralized Model for Simulating Shoreline change), which has been successfully applied in many case studies of shoreline change phenomena on a sandy beach.The model was calibrated using two extracted coastlines satellite imagery data, such as Landsat-5 TM and Landsat-8 OLI/TIRS. The extracted coastline data were analyzed …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …

Uplift Of Shoreline Regions On Pagai Island Due To The September 12, 2007 Mw 8.4 Earthquake Captured By Sar Image, Ashar Muda Lubis

Makara Journal of Technology

At least 25 people were killed by the September 12, 2007 Mw 8.4 Bengkulu earthquake, and many buildings were destroyed in Bengkulu and West Sumatra provinces. It is very important to estimate the earth surface deformation due to the earthquake to understand the rupture size and its process. The aim of this research is to estimate the shoreline change and vertical displacement on Pagai Island associated with the September 12, 2007 Mw 8.4 Bengkulu earthquake. The intensity of ALOS-PALSAR satellite images is used to access the pattern of displacement. The result shows that Pagai Island demonstrated huge uplift due to …

North American Standard For Cold-Formed Steel Framing -- Nonstructural Members, 2015 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Standard For Cold-Formed Steel Structural Framing, 2015 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Standard For Seismic Design Of Cold-Formed Steel Structural Systems, 2015 Edition With Supplement 1, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Phase I Evaluation Of Selected Concrete Material Models In Ls-Dyna, Bradley J. Winkelbauer

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Numerous roadside safety systems are configured with reinforced concrete materials, such as bridge railings, median barriers, and roadside parapets. These protective barrier systems are intended to safely contain and redirect errant vehicles as well as prevent impacts into hazardous fixed objects or other geometric features. The analysis and design of these structures may involve impact simulation with finite element software, like LS-DYNA, which includes multiple concrete material models. For such investigations, limited guidance is available for selecting preferred concrete material models and determining appropriate values for specific parameters. This Phase I study investigated the viability and performance of existing concrete …

Comparative Analysis Of Buckling-Restrained Braced Frames In Eccentric Configuration (Brbf-Es) And Eccentrically Braced Frames (Ebfs), Peter T. Vayda

Civil Engineering Undergraduate Honors Theses

Continuing on the findings of “Using Buckling-Restrained Braced Frames in Eccentric Configuration,” by Dr. Gary S. Prinz, P.E., which determined that, from a performance standpoint, BRBF-Es could be a viable alternative for EBFs. A comparative analysis was conducted on the design procedures and initial cost estimates of BRBF-Es and EBFs. Upon designing four 12-Story buildings (two BRBF-Es and two EBFs), it was determined that BRBF-Es were easier to design due to the statically determinant system. The initial costs estimates of BRBF-Es; however, ranged upwards of 30% more cost than EBFs. Therefore, the initial investment of more intensive structural engineering design …

Use Of Fiber Reinforced Polymer Composite Cable For Post-Tensioning Application, Xiong Yang

FIU Electronic Theses and Dissertations

Corrosion of steel tendons is a major problem for post-tensioned concrete, especially because corrosion of the steel strands is often hard to detect inside grouted ducts. Non-metallic tendons can serve as an alternative material to steel for post-tensioning applications. Carbon fiber reinforced polymer (CFRP), given its higher strength and elastic modulus, as well as excellent durability and fatigue strength, is the most practical option for post-tensioning applications.

The primary objective of this research project was to assess the feasibility of the use of innovative carbon fiber reinforced polymer (CFRP) tendons and to develop guidelines for CFRP in post-tensioned bridge applications, …

Cultural Change Through Bim: Driving Lean Transformation In Education, Avril Behan, Malachy Mathews, Kevin Furlong, Ciara Ahern, Una Beagon, Peter Brennan, Colin Conway, Lee Corcoran, Pierce Fahy, Alan Hore, Barry Mcauley, Trevor Woods

Conference papers

This paper presents a case study of how the adoption of BIM-based practices in the AECO industry is being reflected by cultural change in higher education in Ireland. The silo-mentality that has dominated the AECO sector for more than a century has, despite numerous reorganisations, been replicated in the structures of educational institutions, including in Dublin Institute of Technology since the inception of its founding colleges in the late 1800s. Most AECO programmes must include content that is external to the programme’s specific discipline. Through the School structures of the Institute, delivery of such content is known as "service teaching" …

Soil-Structure Modeling And Design Considerations For Offshore Wind Turbine Monopile Foundations, Wystan Carswell

Doctoral Dissertations

Offshore wind turbine (OWT) support structures account for 20-25% of the capital cost for offshore wind installations, making it essential to optimize the design of the tower, substructure, and foundation to the extent possible. This dissertation focuses on monopile foundations, as the vast majority (approximately 75%) of currently installed OWTs are supported by monopile structures. The objective of this dissertation is to provide information on the behavior of monopile support structures to better substantiate design and planning decisions and to provide a basis for reducing the structural material costs. In pursuit of these objectives, research is presented on the topics …

Effect Of Steel Fiber And Polypropylene Fiber On Reinforced Concrete, Erjola Reufi, Jozefita Marku

UBT International Conference

This paper presents the results of an experimental study that investigated, the effects of steel fibers and polypropylene fibers on the mechanical properties of concrete. Two types of fibers used are hooked end steel fibers of 50 mm and 30 mm length with the aspect ratio of 67 (length 50 mm and diameter 0.75 mm) and 44 (length 30 mm and diameter 0.75 mm). On the other hand, three types of polypropylene fibers are used of length 12mm, 6mm and 3 mm. Steel fibers are used of 0%, 0.25%, 0.5%, and 1% by the volume of concrete and polypropylene fiber …

A Study On Tibiofemoral Joint Contact Area Stresses Using Finite Element Method, Anjeza Gjini, Altin Bidaj, Enio Deneko, Drilona Disha

UBT International Conference

The joints of the human body act as mechanical or building structures joints. Joints connect different segments by enabling the movement of these segments. The design of a joint that provides durability or static support differs from that one which provides only movement. Joints of the human body, as organic joints, are considered more complex than other types of joints. Finite element models help to comprehend the knee structure behavior under the action of dynamic and static loads. Deformations in the articulating cartilage and the distribution of loads from meniscus provide data to understand the effect of loads in different …

Application Of Ec Regulations On Assessment Of The Effect Of Fire On Buildings, Xhemshir Mulliqi

UBT International Conference

The last decade has been characterized by construction of multi-storey buildings in almost all cities of Kosovo, with the storey-height ranging from B+G+4 to B+G+11 and even B+G+15, which means that they need to be subjected to the revision of the main project, including things be verified for the effect of fire. This paper aims to illustrate the use of EC regulations for the verification of reinforced concrete structures under effect of fire, respectively: EN 1991-2-2 Basis of design and actions on structures. Part-2.2: Actions on structures exposed to fire and EN 1992-1-2:2004 Design of concrete structures- part -1-2: Structural …

Application Of En 1991-1-2 Annex E, Using’S Software Package, Xhemshir Mulliqi

UBT International Conference

The fire may occur anywhere and in any phase in the lifetime of a building .Fire resistance requirements should be based on the parameters influencing fire growth and development. For calculating the characteristic fire load, the characteristic fire load has to be determined using the table of EN 1991-1-2 Annex E.The aim of this paper is to present the methodology used in this tool and to show an example of application. The fire resistance of a steel beam submitted to compartment fires which supports a non-collaborating concrete slab in a compartment is estimated in case of an unprotected and a …

Assessment Of Wood Processing Engineers By Requirements Of Leading Manufacturing Entities In Albania, Ramadan Topuzi, Arden Bejtja

UBT International Conference

In Albania a significant number of wood-processing engineers exercise this profession in the field of manufacturing and trading of furniture. In this sector exercise their activity over 800 manufacturing entities distributed across the country with about 9,000 employees. The main purpose of the study is the assessment of wood processing engineers as perceived by the manufacturing entities and their adaptation to the requirements of the labor market . The data collected through a structured questionnaire for this purpose, are thrown into a database (where they are analyzed to generate the results given in this paper. The selection of the respondents …

Structural Analysis Of A Typical Highway Bridge Comparison Between Ktp, En And Aashto Load Models, Endrit Berisha

UBT International Conference

This study consists on a structural analysis comparison of a typical highway bridge between KTP, EN and AASHTO based on load capacity. The Eurocodes are currently in the process of national implementation towards becoming the Europe wide means for structural design of civil engineering works. A team from Mott Macdonald inspected 562 bridges and the main causes of the defects are figured out in the study as traffic load, nature force, and aging, lack of maintenance and design deficiencies. As design codes are advancing with time, the need of Albania to upgrade its code has become a must. This paper …

Design Of Bearing Capacity Of The Driven Piles Of A Highway Bridge Foundation According To 3 Different Methods, Papa Dhimitri, Dervishi Idlir

UBT International Conference

Contemporary design methods of bearing capacity of deep foundation (pile foundation) change according to different design codes. The main requisition of the designing process of the deep foundation is related with the axial bearing capacity, which should be sufficient to withstand the applied loads. Many authors has developed and published detailed methods to analyze the behavior of a single reinforced concrete pile or a group of piles, based on vertical bearing capacity due to lateral friction or residence at the pile point. The goal of this paper is to illustrate the calculation methods according to 3 analytical methods of vertical …

Advanced Construction Materials For Highway Applications, Altin Bidaj, Irakli Premti, Hektor Cullufi

UBT International Conference

Nowadays cost of highway materials increase every year. In addition, use of marginal materials results in early development of pavement distress, requiring more frequent repairs also rehabilitation, associated lane closures, traffic congestion in high volume traffic areas which increases the potential for construction zone accidents and increased levels of environmental pollution related to automobile emissions. Therefore, there is a strong desire in our country to optimize the use of materials currently used for highway pavement construction and to seek advanced materials that are cheaper and environmentally friendly. It has now been recognized that the age of limitless construction materials and …

Motorizing Cbd Of Tirana. A Before And After Study In Tirana From Sustainability Point Of View, Edison Barhani

UBT International Conference

The Center Business District of Tirana (Skanderbeg Square) plays a crucial part in Tirana Transportation System. After a closure of about 2 years, being under reconstruction, CBD opened to traffic on November 14th, 2011. This study analyses performance parameters like: travel time for both cars and buses, waiting time at bus stations, and passenger boarding/alignment for bus passing through or around the CBD before and after it was opened to traffic. Route that follows Kinostudio-Kombinat bus line has been selected as a representative of all other lines passing through the center of Tirana. Opened to traffic for the supply to …

Imperfection Impact On Behavior Of The Secondary Nonstructural Elements And Vertical Non Precise Erection Of Members, Armend Mujaj, Florim Grajçevci, Driton R. Kryeziu, Zijadin Guri, Fisnik Kadiu

UBT International Conference

In this paper of works will be try to present the fundamental computation referring to the imperfection impacts phenomena of non-precise erection effects of the structural members as are vertical columns. Depends from the structural type, the structure should have a vertical structural members with the enough vertical and shear capacity provoked from horizontal action of earthquake, wind, dead and imposed vertical loads. The structural designers, during the structural computation are improve the several approximations creating the dynamic modeling, having into the consideration of structural elements classification in the prior and secondary structural elements. It is very none that the …

Processing Of Gis Data And Building Of 3d Dem Models With Fme Transformer Tools, Hebib Alili, Fadil Shehu, Shenur Muslija

UBT International Conference

The processes of processing of 2D or 3D geodetic or geo-information data by using the FME software and other software's or tools in combination and then through mathematical logics in FME building of such 3D models from original measured terrain data within transformers given by FME, could be considered as very important attempt of creating of such 3D models, exactly when we have to deal with huge data by the size of its as input data. These kind of doing of processing of data through FME software, can be considered as important issue also for resolving of other today related …

Climate Change And Drinking Water, Muhamet Ahmeti, Ilira Abdullahu

UBT International Conference

The period June 2012 – March 2014 saw a prolonged deficit of precipitation below normal. This led to a major continental scale drought across southern Europe, and in eastern Kosova in particular. E.g. see figure 1 below for the month of December 2013, from Drought Monitoring Center for SEE. In fact December 2013 was the fifth driest month in the recorded history of Kosova. February registered the driest month in the recorded hydro-meteorological history of Kosova, since 1927 with only 2.1 mm precipitation, which expressed in Standardized Precipitation Index (SPI). The chance of getting this value in February was 1 …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the well-functioning of the entire structure. The use of a crystalline admixture during the …