Aerodynamics and Fluid Mechanics Commons^™

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Mitigation Of Aeroacoustic Noise Of A Fixed Wing Using Passive Flow Control, Cameron L. Perry

Electronic Theses and Dissertations

As the world becomes more environmentally conscious, noise pollution is of increasing concern. In this study, shallow dimples are applied to a NACA 0012 airfoil at multiple angles of attack (AoA) with the intent of reducing aeroacoustic noise emissions. Both Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) models are used for aerodynamic and aeroacoustic investigations, respectively, at a fixed Reynolds number of 4.8 x 10⁵. Altering the dimple depth to diameter ratio (d/D) from 2.5% to 15% is first investigated, with a d/D of 5% or lower resulting in the least aerodynamic impact. The transition from …

Feasibility Study Of Slotted, Natural-Laminar-Flow Airfoils For High-Lift Applications, Hector David Ortiz Melendez

Doctoral Dissertations

A computational fluid dynamics approach to evaluate the feasibility of a slotted, natural-laminar-flow airfoil designed for transonic applications, to perform as a high-lift system was developed. Reynolds-Averaged Navier-Stokes equations with a laminar-turbulent transition model for subsonic flow at representative flight conditions were used for this analysis. Baseline high-lift simulations were performed to understand the stall characteristics of the slotted, natural-laminar-flow airfoil. Maximum aerodynamic efficiency was observed with a constant slot-width. In addition, the effectiveness of the aft-element as a high-lift device was explored. Results indicate that a micro-flap is a viable option as a lift effector. These are most effective …

A Study Of Asymmetric Supersonic Wind Tunnel Nozzle Design, Brittany A. Davis

Mechanical & Aerospace Engineering Theses & Dissertations

Achieving higher Mach numbers for private and commercial flight is a growing interest in the aerospace community. To qualify vehicles prior to flight, tests must be run in wind tunnels. Asymmetric wind tunnel nozzles are of continuing interest to the aerospace community due to their ability to change throat geometry, allowing for a range of Mach numbers to be achieved that encompasses all of the supersonic regime. The sliding block wind tunnel at Old Dominion University (ODU) is designed for a range of Mach numbers from about 1.8 to 3.5 but is limited to an upper limit of 2.8 by …

A Computational Fluid Dynamics-Based Surrogate Wind Turbine Blade Aerodynamic Model For Hybrid Simulation, Eric Lalonde

Electronic Thesis and Dissertation Repository

Hybrid simulation (HS) is a promising technique for studying wind turbines due to the presence of scaling errors in wind tunnel testing. However, HS of wind-loaded structures is limited by the current practice of using lower-accuracy, "pre-calculated" aerodynamic loads, which uncouple the aerodynamic loading from the structural response. This thesis presents six stand-alone studies that collectively build towards a novel HS framework that employs a computational fluid dynamics (CFD) based surrogate model to generate higher-accuracy aerodynamic loads within the HS loop. An experimentally-validated residential wind turbine model equipped with an external damping system was used to illustrate the proposed framework. …

Simulating The Effects Of Floating Platforms, Tilted Rotors, And Breaking Waves For Offshore Wind Turbines, Hannah Johlas

Doctoral Dissertations

Offshore wind energy is a rapidly expanding source of renewable energy worldwide, but many aspects of offshore wind turbine behavior are still poorly understood and are not accurately captured by low-cost engineering models used in the design process. To help improve these models, computational fluid dynamics (CFD) can provide valuable insight into the complex fluid flows that affect offshore wind turbine power generation and structural loads. This research uses CFD simulations to examine three main topics important to future offshore wind development: how breaking waves affect structural loads for fixed-bottom wind turbines; how platform motions affect power generation, wake characteristics, …

Optimizing Design Parameters For Active Flow Control Boundary-Layer Fence Performance Enhancement On A Delta Wing, Nathan L. Tedder

Theses and Dissertations

Utilizing computational fluid dynamic (CFD) simulations, the presented study is able to further the investigation of replicating and improving upon the performance of a NACA 0012 cropped half-span delta-wing at high angles-of-attack with an active flow control fluidic fence via wall-normal, steady blowing from an optimized single chordwise slot located at z/b = 70%,. The data is generated using CREATE-AV Kestrel v10.1rc5 CFD software on the Department of Defense High Performance Computing systems. The flight regime is held constant at a Mach number of 0.18 and a Reynolds number (Re) of 5.0 x 10⁵, based on the root …

Helios And Tenasi Results For The Workshop For Integrated Propeller Prediction, Aaron Crawford

Honors Theses

Beginning in 2018, the AIAA began the workshop for integrated propeller prediction. This effort was intended to bolster the CFD prediction capabilities of the aerospace community due to a resurgent interest in propeller driven vehicles for electric applications. The test bed for this workshop is the NASA X-57, a model of which was experimentally tested in the Lockheed Martin Low Speed Wind Tunnel in January 2019. Using the 3D scanned geometry provided by the workshop a mesh was created and all priority one simulations were performed using two flow solvers. The flow solvers used were Helios, developed by the ADD …

A Numerical Investigation Of Microgravity Evaporation, Daniel Peter Ringle

Dissertations and Theses

Evaporation is important to myriad engineering processes such as cooling, distillation, thin film deposition, and others. In fact, NASA has renewed interest in using cabin air pressure evaporation as a means to recycle waste water in space. As one example, NASA recently conducted experiments aboard the International Space Station (ISS) to measure evaporation rates in microgravity and to determine the impacts of porous structure on the process. It has long been assumed that differences in evaporation rates between 1-g₀ and microgravity are small. However, discrepancies by as much as 40% have been observed in practice. The assumption now …

Rough Airfoil Simulation For Wind Turbine Applications, Nathaniel B. Develder

Doctoral Dissertations

As a result of insects or other environmental fouling, surface roughness on wind turbine blades can reduce power output significantly. Superhydrophobic surfaces, though possibly a passive, cost-saving, answer to the problem of ice accretion on wind turbine rotors in cold climates, may alter turbulence development in the blade boundary layer similar to environmental roughness. This work uses an equivalent sand grain extension to the Turbulent Potential model to computationally assess the aerodynamic effects of surface roughness on the s809 airfoil, including a representational superhydrophobic surface. Rough surface boundary layer theory, application of the equivalent sand grain method, roughness parameter correlation, …

Numerical Study Of Spacer Grid Geometry In A 5 X 5 Nuclear Fuel Rod Bundle, Wan Chuan Fan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Reactor fuel rod bundles serve as the primary heat source in light water reactors (LWRs), commonly found in the aforementioned PWR plants. The fuel rod bundles’ structure consists of a collection of fuel rods put into a parallel grid configuration. The bundles also include fuel rod spacers, which hold the fuel rods in place, in accordance with the grid. Repeating structures of the fuel bundles create the meta-structure in the reactor. In other words, the grid configuration repeats until it fills the entire space of the reactor. This results in reactor fuel rods suspended in the working fluid domain, oriented …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

Thermochemical Non-Equilibrium Models For Weakly Ionized Hypersonic Flows With Application To Slender-Body Wakes, Matthew P. Clarey

Theses and Dissertations

The current resurgence of interest in hypersonic technologies has warranted an inquiry into the commonly employed thermochemical non-equilibrium models within computational fluid dynamic (CFD) simulations. Additionally, research has historically focused on forebody flowfields, while studies of the complex wake structure have remained elusive. Although the forebody is of significance for vehicle analysis, the wake presents many exploitative characteristics. This dissertation aimed to address these two deficits. First, two three-temperature non-equilibrium models were developed, increasing the fidelity of hypersonic solutions above that of the legacy two-temperature model. The models were then investigated via zero-dimensional simulations, to detail the non-equilibrium processes, and …

Dust Control Examination Using Computational Fluid Dynamics Modeling And Laboratory Testing Of Vortecone And Impingement Screen Filters, Ashish R. Kumar

Theses and Dissertations--Mining Engineering

Heavy industries, such as mining, generate dust in quantities that present an occupational health hazard. Prolonged exposure to the respirable dust has been found to result in many irreversible occupational ailments in thousands of miners. In underground mining applications, a variety of scrubbing systems are used to remove dust near the zones of generation. However, the wire-mesh type fibrous screens in the flooded-bed dust scrubbers used on continuous miners, are prone to clogging due to the accumulation of dust particles. This clogging results in a reduced capture efficiency and a higher exposure to the personnel. This research establishes the Vortecone, …

Aerodynamic Design And Analysis Of A Large-Scale Stall-Regulated H-Type Vertical Axis Wind Turbine For An Offshire Floating Installation, Brian Peter Hand

PhDs

Wind energy has witnessed a consistent expansion over the past decade, especially with the move to offshore installation. There is an increasing need to further exploit superior offshore wind resources, which is pushing multi-megawatt wind turbines into deeper water locations where the current popular horizontal axis wind turbine configuration is not entirely suitable. In particular, there has been a renewed interest in the vertical axis wind turbine (VAWT) configuration due to its inherent design attributes for an offshore floating application and also its potential to provide a significant reduction in the system cost of energy. However, challenges still remain as …

Design And Computational Fluid Dynamics Analysis Of An Idealized Modern Wingsuit, Maria E. Ferguson

McKelvey School of Engineering Theses & Dissertations

The aerodynamics of a modern wingsuit has been the subject of very few detailed scientific studies to date. The prevailing design process remains the dangerous “sew and fly” method, in which designs are tested when they are first flown. This study utilizes Computational Fluid Dynamics (CFD) tools to analyze the flow field and aerodynamics of an idealized wingsuit, which is designed using Computer-Aided Design (CAD) modeling. The 3D CAD software Autodesk Inventor is used to create the wingsuit model, which is designed with a Gottingen 228 airfoil cross-section and a relatively large planform of aspect ratio 1.3. The commercial flow …

Freedrop Testing And Cfd Simulation Of Ice Models From A Cavity Into Supersonic Flow, Thomas J. Flora

Theses and Dissertations

Weapon release at supersonic speeds from an internal bay is highly advantageous. For this reason, both experimental and numerical methods were used to investigate store separation from a cavity (L=D=4.5) into Mach 2.94 flow. The experiment used a piezoresistive pressure transducer, Schlieren and high-speed photography for data acquisition. The computational solution used the OVERFLOW solver. A sphere and a Mk-82, scaled to 1:20, were formed using frozen tap water. The sphere model was freedrop tested experimentally and computationally, while the sub-scale store shaped model was freedrop tested experimentally. The total pressure was varied to alter the dynamic response of the …

Numerical Investigation Of Highly Curved Turbulent Flows In Centrifugal Compressors And In A Simplified Geometry, Kevin J. Elliott

Electronic Thesis and Dissertation Repository

Curvature effects are investigated in terms of a recently developed curvature corrected turbulence model in turbomachinery applications. Two centrifugal compressor stages and a curved geometry modelled after a centrifugal impeller are simulated using the curvature corrected SST (SST-CC) turbulence model. This work improves the understanding of how the SST-CC model predicts curvature effects. An analysis of the SST-CC production multiplier in both centrifugal cases reveals that the model is appropriately accounting for curvature effects, showing increased production near concave surfaces and decreased production near convex surfaces. This correlates well with the simplified geometry results and demonstrates that the simplified geometry …

Cfd Study On Aerodynamic Effects Of A Rear Wing/Spoiler On A Passenger Vehicle, Mustafa Cakir

Mechanical Engineering Master's Theses

Aerodynamic characteristics of a racing car are of significant interest in reducing car-racing accidents due to wind loading and in reducing the fuel consumption. At the present, modified car racing becomes more popular around the world. Sports cars are most commonly seen with spoilers, such as Ford Mustang, Subaru Impreza, and Chevrolet Corvette. Even though these vehicles typically have a more rigid chassis and a stiffer suspension to aid in high-speed maneuverability, a spoiler can still be beneficial. One of the design goals of a spoiler is to reduce drag and increase fuel efficiency. Many vehicles have a fairly steep …

A Filter-Forcing Turbulence Model For Large Eddy Simulation Incorporating The Compressible "Poor Man's" Navier--Stokes Equations, Joshua Strodtbeck

Theses and Dissertations--Mechanical Engineering

A new approach to large-eddy simulation (LES) based on the use of explicit spatial filtering combined with backscatter forcing is presented. The forcing uses a discrete dynamical system (DDS) called the compressible ``poor man's'' Navier--Stokes (CPMNS) equations. This DDS is derived from the governing equations and is shown to exhibit good spectral and dynamical properties for use in a turbulence model. An overview and critique of existing turbulence theory and turbulence models is given. A comprehensive theoretical case is presented arguing that traditional LES equations contain unresolved scales in terms generally thought to be resolved, and that this can only …

Cfd Analysis Of A Uni-Directional Impulse Turbine For Wave Energy Conversion, Carlos Alberto Velez

Electronic Theses and Dissertations

Ocean energy research has grown in popularity in the past decade and has produced various designs for wave energy extraction. This thesis focuses on the performance analysis of a uni-directional impulse turbine for wave energy conversion. Uni-directional impulse turbines can produce uni-directional rotation in bi-directional flow, which makes it ideal for wave energy extraction as the motion of ocean waves are inherently bi-directional. This impulse turbine is currently in use in four of the world’s Oscillating Wave Columns (OWC). Current research to date has documented the performance of the turbine but little research has been completed to understand the flow …

Novel Inverse Airfoil Design Utilizing Parametric Equations, Kevin A. Lane

Master's Theses

The engineering problem of airfoil design has been of great theoretical interest for almost a century and has led to hundreds of papers written and dozens of methods developed over the years. This interest stems from the practical implications of airfoil design. Airfoil selection significantly influences the application's aerodynamic performance. Tailoring an airfoil profile to its specific application can have great performance advantages. This includes considerations of the lift and drag characteristics, pitching moment, volume for fuel and structure, maximum lift coefficient, stall characteristics, as well as off-design performance.

A common way to think about airfoil design is optimization, the …

Cfd Analysis Of Experimental Wing And Winglet For Falconlaunch 8 And The Exfit Program, Benjamin P. Switzer

Theses and Dissertations

Reusable launch vehicles have many benefits over their expendable counterparts. These benefits range from cost reductions to increased functionality of the vehicles. Further research is required in the development of the technology necessary for reusable launch vehicles to come to fruition. The Air Force Institute of Technology’s future involvement in the ExFIT program will entail designing and testing of a new wing tip mounted vertical stabilizer in the hypersonic regime. One proposed venue for experimentation is to utilize the United States Air Force Academy’s FalconLAUNCH Program which annually designs, builds, and launches a sounding rocket capable of reaching hypersonic speeds. …

Comparative Study Of Aerodynamic Interference During Aft Dispense Of Munitions, Matthew G. Burkinshaw

Theses and Dissertations

Based on forthcoming USAF needs, an investigation was launched to further the understanding of aft dispense of munitions in a high-speed environment. A computational fluid dynamics (CFD) study was performed followed by a wind tunnel experiment. The study consisted of a strut-mounted cone simulating a parent vehicle and a sting mounted cone-cylinder store situated directly behind the cone. The CFD modeled the test objects inside a supersonic wind tunnel in which the experiments took place. The CFD study consisted of evaluating a new strut designed to reduce asymmetry in the airflow aft of the cone. The CFD study also included …

Dynamic Aeroelastic Analysis Of Wing/Store Configurations, Gregory H. Parker

Theses and Dissertations

Limit-cycle oscillation, or LCO, is an aeroelastic phenomenon characterized by limited amplitude, self-sustaining oscillations produced by fluid-structure interactions. In order to study this phenomenon, code was developed to interface a modal structural model with a commercial computational fluid dynamics program. LCO was simulated for a rectangular wing, referred to as the Goland⁺ wing. It was determined that the aerodynamic nonlinearity responsible for LCO in the Goland+ wing was the combination of strong trailing-edge and lambda shocks which periodically appear and disappear. This mechanism limited the flow of energy into the structure which quenched the growth of the flutter, resulting …

Implementation And Testing Of Unsteady Reynolds-Averaged Navier-Stokes And Detached Eddy Simulation Using An Implicit Unstructured Multigrid Scheme, Juan A. Palaez

Mechanical & Aerospace Engineering Theses & Dissertations

Investigation and development of the Detached Eddy Simulation (DES) technique for the computation of unsteady flows on unstructured grids are presented. The motivation of the research work is driven by the ultimate goal of predicting separated flows of aerodynamic importance, such as massive stall or flows over complex non-streamlined geometries. These cases, in which large regions of massively separated flow are present, represent a challenge for conventional Unsteady Reynolds-Averaged Navier-Stokes (URANS) models, that in many cases, cannot produce solutions accurate enough and/or fast enough for industrial design and applications. A Detached Eddy Simulation model is implemented and its performance compared …

Three-Dimensional Aerodynamic Design Optimization Using Discrete Sensitivity Analysis And Parallel Computing, Amidu Olawale Oloso

Mechanical & Aerospace Engineering Theses & Dissertations

A hybrid automatic differentiation/incremental iterative method was implemented in the general purpose advanced computational fluid dynamics code (CFL3D Version 4.1) to yield a new code (CFL3D.ADII) that is capable of computing consistently discrete first order sensitivity derivatives for complex geometries. With the exception of unsteady problems, the new code retains all the useful features and capabilities of the original CFL3D flow analysis code. The superiority of the new code over a carefully applied method of finite-differences is demonstrated.

A coarse grain, scalable, distributed-memory, parallel version of CFL3D.ADII was developed based on "derivative stripmining". In this data-parallel approach, an identical copy …